Abstract: The material behavior of graphene, a single layer of
carbon lattice, is extremely sensitive to its dielectric environment. We
demonstrate improvement in electronic performance of graphene
nanowire interconnects with full encapsulation by lattice-matching,
chemically inert, 2D layered insulator hexagonal boron nitride (h-
BN). A novel layer-based transfer technique is developed to construct
the h-BN/MLG/h-BN heterostructures. The encapsulated graphene
wires are characterized and compared with that on SiO2 or h-BN
substrate without passivating h-BN layer. Significant improvements
in maximum current-carrying density, breakdown threshold, and
power density in encapsulated graphene wires are observed. These
critical improvements are achieved without compromising the carrier
transport characteristics in graphene. Furthermore, graphene wires
exhibit electrical behavior less insensitive to ambient conditions, as
compared with the non-passivated ones. Overall, h-BN/graphene/h-
BN heterostructure presents a robust material platform towards the
implementation of high-speed carbon-based interconnects.
Abstract: The first pn-type carrier-induced silicon Bragg-grating filter is demonstrated. The extinction-ratio modulations are 11.5 dB and 10 dB with reverse and forward biases, respectively. 8-Gpbs data rate is achieved with a reverse bias.
Abstract: In this paper, we demonstrated a 1 × 4 silicon photonic cascaded arrayed waveguide grating, which is fabricated on a SOI wafer with a 220 nm top Si layer and a 2µm buried oxide layer. The measured on-chip transmission loss of this cascaded arrayed waveguide grating is ~ 5.6 dB, including the fiber-to-waveguide coupling loss. The adjacent crosstalk is 33.2 dB. Compared to the normal single silicon photonic arrayed waveguide grating with a crosstalk of ~ 12.5 dB, the crosstalk of this device has been dramatically increased.
Abstract: In order to clarify the structure of the cold flow discharged from the vortex tube (VT), the pressure of the cold flow was measured, and a simple flow visualization technique using a 0.75mm-diameter needle and an oily paint is made to study the reverse flow at the cold exit. It is clear that a negative pressure and positive pressure region exist at a certain pressure and cold fraction area, and that a reverse flow is observed in the negative pressure region.
Abstract: A theoretical investigation from the view point of gas-dynamics and thermodynamics was carried out, in order to clarify the energy separation mechanism in a viscous compressible vortex, as a primary flow element in a uni-flow vortex tube. The mathematical solutions of tangential velocity, density and temperature in a viscous compressible vortical flow were used in this study.It is clear that a total temperature in the vortex core falls well below that distant from the vortex core in the radial direction, causing aregion with higher total temperature,compared to the distant region,peripheral to the vortex core.
Abstract: By the real representation of the quaternionic matrix,
an iterative method for quaternionic linear equations Ax = b is
proposed. Then the convergence conditions are obtained. At last, a
numerical example is given to illustrate the efficiency of this method.
Abstract: In this paper, we propose a method for detecting
circular shapes with subpixel accuracy. First, the geometric properties
of circles have been used to find the diameters as well as the
circumference pixels. The center and radius are then estimated by the
circumference pixels. Both synthetic and real images have been tested
by the proposed method. The experimental results show that the new
method is efficient.
Abstract: A stack with a small critical temperature gradient is
desirable for a standing wave thermoacoustic engine to obtain a low
onset temperature difference (the minimum temperature difference to
start engine-s self-oscillation). The viscous and heat relaxation loss in
the stack determines the critical temperature gradient. In this work, a
dimensionless critical temperature gradient factor is obtained based
on the linear thermoacoustic theory. It is indicated that the
impedance determines the proportion between the viscous loss, heat
relaxation losses and the power production from the heat energy. It
reveals the effects of the channel dimensions, geometrical
configuration and the local acoustic impedance on the critical
temperature gradient in stacks. The numerical analysis shows that
there exists a possible optimum combination of these parameters
which leads to the lowest critical temperature gradient. Furthermore,
several different geometries have been tested and compared
numerically.
Abstract: This paper investigates vortex shedding processes
occurring at the end of a stack of parallel plates, due to an oscillating
flow induced by an acoustic standing wave within an acoustic
resonator. Here, Particle Image Velocimetry (PIV) is used to quantify
the vortex shedding processes within an acoustic cycle
phase-by-phase, in particular during the “ejection" of the fluid out of
the stack. Standard hot-wire anemometry measurement is also applied
to detect the velocity fluctuations near the end of the stack.
Combination of these two measurement techniques allowed a detailed
analysis of the vortex shedding phenomena. The results obtained show
that, as the Reynolds number varies (by varying the plate thickness
and drive ratio), different flow patterns of vortex shedding are
observed by the PIV measurement. On the other hand, the
time-dependent hot-wire measurements allow obtaining detailed
frequency spectra of the velocity signal, used for calculating
characteristic Strouhal numbers. The impact of the plate thickness and
the Reynolds number on the vortex shedding pattern has been
discussed. Furthermore, a detailed map of the relationship between the
Strouhal number and Reynolds number has been obtained and
discussed.
Abstract: In a travelling wave thermoacoustic device, the
regenerator sandwiched between a pair of (hot and cold) heat
exchangers constitutes the so-called thermoacoustic core, where the
thermoacoustic energy conversion from heat to acoustic power takes
place. The temperature gradient along the regenerator caused by the
two heat exchangers excites and maintains the acoustic wave in the
resonator. The devices are called travelling wave thermoacoustic
systems because the phase angle difference between the pressure and
velocity oscillation is close to zero in the regenerator. This paper
presents the construction and testing of a thermoacoustic engine
equipped with a ceramic regenerator, made from a ceramic material
that is usually used as catalyst substrate in vehicles- exhaust systems,
with fine square channels (900 cells per square inch). The testing
includes the onset temperature difference (minimum temperature
difference required to start the acoustic oscillation in an engine), the
acoustic power output, thermal efficiency and the temperature profile
along the regenerator.
Abstract: Safety of bus journey is a fundamental concern. Risk of injuries and fatalities is severe when bus superstructure fails during rollover accident. Adequate design and sufficient strength of bus superstructure can reduce the number of injuries and fatalities. This paper deals with structural analysis of bus superstructure undergoes rollover event. Several value of mass will be varied in multiple simulations. The purpose of this work is to analyze structural response of bus superstructure in terms of deformation, stress and strain under several loading and constraining conditions. A complete bus superstructure with forty four passenger-s capability was developed using finite element analysis software. Simulations have been conducted to observe the effect of total mass of bus on the strength of superstructure. These simulations are following United Nation Economic Commission of Europe regulation 66 which focuses on strength of large vehicle superstructure. Validation process had been done using simple box model experiment and results obtained are comparing with simulation results. Inputs data from validation process had been used in full scale simulation. Analyses suggested that, the failure of bus superstructure during rollover situation is basically dependent on the total mass of bus and on the strength of bus superstructure.
Abstract: We demonstrate a 1×4 coarse wavelength
division-multiplexing (CWDM) planar concave grating
multiplexer/demultiplexer and its application in re-configurable
optical add/drop multiplexer (ROADM) system in silicon-on-insulator
substrate. The wavelengths of the demonstrated concave grating
multiplexer align well with the ITU-T standard. We demonstrate a
prototype of ROADM comprising two such concave gratings and four
wide-band thermo-optical MZI switches. Undercut technology which
removes the underneath silicon substrate is adopted in optical switches
in order to minimize the operation power. For all the thermal heaters,
the operation voltage is smaller than 1.5 V, and the switch power is
~2.4 mW. High throughput pseudorandom binary sequence (PRBS)
data transmission with up to 100 Gb/s is demonstrated, showing the
high-performance ROADM functionality.