Abstract: Rice straw is lignocellulosic biomass which can be utilized as substrate for the biogas production. However, due to the property and composition of rice straw, it is difficult to be degraded by hydrolysis enzymes. One of the pretreatment methods that modify such properties of lignocellulosic biomass is the application of lignocellulose-degrading microbial consortia. The aim of this study is to investigate the effect of microbial consortia to enhance biogas production. To select the high efficient consortium, cellulase enzymes were extracted and their activities were analyzed. The results suggested that microbial consortium culture obtained from cattle manure is the best candidate compared to decomposed wood and horse manure. A microbial consortium isolated from cattle manure was then mixed with anaerobic sludge and used as inoculum for biogas production. The optimal conditions for biogas production were investigated using response surface methodology (RSM). The tested parameters were the ratio of amount of microbial consortium isolated and amount of anaerobic sludge (MI:AS), substrate to inoculum ratio (S:I) and temperature. Here, the value of the regression coefficient R2 = 0.7661 could be explained by the model which is high to advocate the significance of the model. The highest cumulative biogas yield was 104.6 ml/g-rice straw at optimum ratio of MI:AS, ratio of S:I, and temperature of 2.5:1, 15:1 and 44°C respectively.
Abstract: The present work attempts to investigate the
combustion, performance and emission characteristics of an existing
single-cylinder four-stroke compression-ignition engine operated in
dual-fuel mode with hydrogen as an alternative fuel. Environmental
concerns and limited amount of petroleum fuels have caused interests
in the development of alternative fuels like hydrogen for internal
combustion (IC) engines. In this experimental investigation, a diesel
engine is made to run using hydrogen in dual fuel mode with diesel,
where hydrogen is introduced into the intake manifold using an LPGCNG
injector and pilot diesel is injected using diesel injectors. A
Timed Manifold Injection (TMI) system has been developed to vary
the injection strategies. The optimized timing for the injection of
hydrogen was 10^0 CA after top dead center (ATDC). From the study
it was observed that with increasing hydrogen rate, enhancement in
brake thermal efficiency (BTHE) of the engine has been observed
with reduction in brake specific energy consumption (BSEC).
Furthermore, Soot contents decrease with an increase in indicated
specific NOx emissions with the enhancement of hydrogen flow rate.
Abstract: We address a new integer frequency offset (IFO)
estimation scheme with an aid of a pilot for orthogonal frequency
division multiplexing systems. After correlating each continual pilot
with a predetermined scattered pilot, the correlation value is again
correlated to alleviate the influence of the timing offset. From
numerical results, it is demonstrated that the influence of the timing
offset on the IFO estimation is significantly decreased.
Abstract: Entrepreneurs face different sort of difficulties
especially with customers, organizations and employees. Emotional
intelligence which is the ability to understand and control the
emotions is an important factor to help entrepreneurs end up
challenges to the result they prefer. So it is assumed that
entrepreneurs especially those who have passed the first challenging
years of starting a new business, have high emotional intelligence. In
this study the Iranian established entrepreneurs have been surveyed.
According to Iran Gem 2014 report the percentage of established
entrepreneur in Iran is 10.92%. So by using Cochran sample formula
(1%) 96 Iranian established entrepreneurs have been selected and
Emotional intelligence appraisal questionnaire distributed to them.
The SPSS19 result shows high emotional intelligence in Iranian
established entrepreneurs.
Abstract: This work proposes a data-driven multiscale based
quantitative measures to reveal the underlying complexity of
electroencephalogram (EEG), applying to a rodent model of
hypoxic-ischemic brain injury and recovery. Motivated by that real
EEG recording is nonlinear and non-stationary over different
frequencies or scales, there is a need of more suitable approach over
the conventional single scale based tools for analyzing the EEG data.
Here, we present a new framework of complexity measures
considering changing dynamics over multiple oscillatory scales. The
proposed multiscale complexity is obtained by calculating entropies of
the probability distributions of the intrinsic mode functions extracted
by the empirical mode decomposition (EMD) of EEG. To quantify
EEG recording of a rat model of hypoxic-ischemic brain injury
following cardiac arrest, the multiscale version of Tsallis entropy is
examined. To validate the proposed complexity measure, actual EEG
recordings from rats (n=9) experiencing 7 min cardiac arrest followed
by resuscitation were analyzed. Experimental results demonstrate that
the use of the multiscale Tsallis entropy leads to better discrimination
of the injury levels and improved correlations with the neurological
deficit evaluation after 72 hours after cardiac arrest, thus suggesting an
effective metric as a prognostic tool.
Abstract: The paper presents a new method for efficient
innovation process management. Even though the innovation
management methods, tools and knowledge are well established and
documented in literature, most of the companies still do not manage it
efficiently. Especially in SMEs the front end of innovation - problem
identification, idea creation and selection - is often not optimally
performed. Our eMIPS methodology represents a sort of "umbrella
methodology" - a well-defined set of procedures, which can be
dynamically adapted to the concrete case in a company. In daily
practice, various methods (e.g. for problem identification and idea
creation) can be applied, depending on the company's needs. It is
based on the proactive involvement of the company's employees
supported by the appropriate methodology and external experts. The
presented phases are performed via a mixture of face-to-face
activities (workshops) and online (eLearning) activities taking place
in eLearning Moodle environment and using other e-communication
channels. One part of the outcomes is an identified set of
opportunities and concrete solutions ready for implementation. The
other also very important result is connected to innovation
competences for the participating employees related with concrete
tools and methods for idea management. In addition, the employees
get a strong experience for dynamic, efficient and solution oriented
managing of the invention process. The eMIPS also represents a way
of establishing or improving the innovation culture in the
organization. The first results in a pilot company showed excellent
results regarding the motivation of participants and also as to the
results achieved.
Abstract: This paper presents effects of the mean operating
pressure on the optimal operating frequency based on temperature
differences across stack ends in a thermoacoustic refrigerator. In
addition to the length of the resonance tube, components of the
thermoacoustic refrigerator have an influence on the operating
frequency due to their acoustic properties, i.e., absorptivity,
reflectivity and transmissivity. The interference of waves incurs and
distorts the original frequency generated by the driver so that the
optimal operating frequency differs from the designs. These acoustic
properties are not parameters in the designs and be very complicated
to infer their responses. A prototype thermoacoustic refrigerator is
constructed and used to investigate its optimal operating frequency
compared to the design at various operating pressures. Helium and air
are used as working fluids during the experiments. The results
indicate that the optimal operating frequency of the prototype
thermoacoustic refrigerator using helium is at 6 bar and 490Hz or
approximately 20% away from the design frequency. The optimal
operating frequency at other mean pressures differs from the design
in an unpredictable manner, however, the optimal operating
frequency and pressure can be identified by testing.
Abstract: A cold, thin film of liquid impinging on an isothermal
hot, horizontal surface has been investigated. An approximate
solution for the velocity and temperature distributions in the flow
along the horizontal surface is developed, which exploits the
hydrodynamic similarity solution for thin film flow. The approximate
solution may provide a valuable basis for assessing flow and heat
transfer in more complex settings.
Abstract: This paper presents dynamic models of distributed
generators (DG) and investigates dynamic behavior of the DG units
in the micro grid system. The DG units include photovoltaic and fuel
cell sources. The voltage source inverter is adopted since the
electronic interface which can be equipped with its controller to keep
stability of the micro grid during small signal dynamics. This paper
also introduces power management strategies and implements the DG
load sharing concept to keep the micro grid operation in gridconnected
and islanding modes of operation. The results demonstrate
the operation and performance of the photovoltaic and fuel cell as
distributed generators in a micro grid. The entire control system in
the micro grid is developed by combining the benefits of the power
control and the voltage control strategies. Simulation results are all
reported, confirming the validity of the proposed control technique.
Abstract: The thermal performance of a solar water heating with
1.00 m2 flat plate collectors in Cascavel - PR, is which presented in
this article, paper presents the solution to leverage the marketing of
solar heating systems through detailed constituent materials of the
solar collector studies, these abundant materials in construction, such
as expanded polyethylene, PVC, aluminum and glass tubes, mixing
them with new materials to minimize loss of efficiency while
decreasing its cost. The system was tested during months and the
collector obtained maximum recorded temperature of outlet fluid of
55°C, while the maximum temperature of the water at the bottom of
the hot water tank was 35°C. The average daily energy collected was
19.6 MJ/d; the energy supplied by the solar plate was 16.2 MJ/d; the
loss in the feed pipe was 3.2 MJ/d; the solar fraction was 32.2%, the
efficiency of the collector was 45.6% and the efficiency of the system
was 37.8%.
Abstract: Honeys are produced by Apis mellifera and stingless
bees (Meliponini) in Ecuador. We studied honey produced in
beeswax combs by Apis mellifera, and honey produced in pots by
Geotrigona and Scaptotrigona bees. Chloroform extracts of honey
were obtained for fast NMR spectra. The 1D spectra were acquired at
298 K, with a 600 MHz NMR Bruker instrument, using a modified
double pulsed field gradient spin echoes (DPFGSE) sequence.
Signals of 1H NMR spectra were integrated and used as inputs for
PCA, PLS-DA analysis, and labelled sets of classes were successfully
identified, enhancing the separation between the three groups of
honey according to the entomological origin: A. mellifera,
Geotrigona and Scaptotrigona. This procedure is therefore
recommended for authenticity test of honey in Ecuador.
Abstract: In this research the effect of moisture at three levels
(47, 57, and 67 w.b.%) on the physical properties of the Pofaki pea
variety including, dimensions, geometric mean diameter, volume,
sphericity index and the surface area was determined. The influence
of different moisture levels (47, 57 and 67 w.b.%), in two loading
orientation (longitudinal and transverse) and three loading speed (4,6
and 8 mm min-1) on the mechanical properties of pea such as
maximum deformation, rupture force, rupture energy, toughness and
the power to break the pea was investigated. It was observed in the
physical properties that moisture changes were affective at 1% on,
dimensions, geometric mean diameter, volume, sphericity index and
the surface area. It was observed in the mechanical properties that
moisture changes were effective at 1% on, maximum deformation,
rupture force, rupture energy, toughness and the power to break.
Loading speed was effective on maximum deformation, rupture
force, rupture energy at 1% and it was effective on toughness at 5%.
Loading orientation was effective on maximum deformation, rupture
force, rupture energy, toughness at 1% and it was effective on power
at 5%. The mutual effect of speed and orientation were effective on
rupture energy at 1% and were effective on toughness at 5%
probability. The mutual effect of moisture and speed were effective
on rupture force and rupture energy at 1% and were effective on
toughness 5% probability. The mutual effect of orientation and
moisture on rupture energy and toughness were effective at 1%.
Abstract: This paper deals with the theoretical and numerical
investigation of magneto hydrodynamic boundary layer flow of a
nanofluid past a wedge shaped wick in heat pipe used for the cooling
of electronic components and different type of machines. To
incorporate the effect of nanoparticle diameter, concentration of
nanoparticles in the pure fluid, nanothermal layer formed around the
nanoparticle and Brownian motion of nanoparticles etc., appropriate
models are used for the effective thermal and physical properties of
nanofluids. To model the rotation of nanoparticles inside the base
fluid, microfluidics theory is used. In this investigation ethylene
glycol (EG) based nanofluids, are taken into account. The non-linear
equations governing the flow and heat transfer are solved by using a
very effective particle swarm optimization technique along with
Runge-Kutta method. The values of heat transfer coefficient are
found for different parameters involved in the formulation viz.
nanoparticle concentration, nanoparticle size, magnetic field and
wedge angle etc. It is found that, the wedge angle, presence of
magnetic field, nanoparticle size and nanoparticle concentration etc.
have prominent effects on fluid flow and heat transfer characteristics
for the considered configuration.
Abstract: By textile science incorporating with electronic
industry, developed textile products start to take part in different
areas such as industry, military, space, medical etc. for health,
protection, defense, communication and automation. Electronic
textiles (e-textiles) are fabrics that contain electronics and
interconnections with them. In this study, two types of base yarns
(cotton and acrylic) and three types of conductive steel yarns with
different linear resistance values (14Ω/m, 30Ω/m, 70Ω/m) were used
to investigate the effect of base yarn type and linear resistance of
conductive yarns on thermal behavior of e-textile structures. Thermal
behavior of samples was examined by thermal camera.
Abstract: Control of honey frauds is needed in Ecuador to
protect bee keepers and consumers because simple syrups and new
syrups with eucalyptus are sold as genuine honeys. Authenticity of
Ecuadorian commercial honeys was tested with a vortex emulsion
consisting on one volume of honey:water (1:1) dilution, and two
volumes of diethyl ether. This method allows a separation of phases
in one minute to discriminate genuine honeys that form three phase
and fake honeys that form two phases; 34 of the 42 honeys analyzed
from five provinces of Ecuador were genuine. This was confirmed
with 1H NMR spectra of honey dilutions in deuterated water with an
enhanced amino acid region with signals for proline, phenylalanine
and tyrosine. Classic quality indicators were also tested with this
method (sugars, HMF), indicators of fermentation (ethanol, acetic
acid), and residues of citric acid used in the syrup manufacture. One
of the honeys gave a false positive for genuine, being an admixture of
genuine honey with added syrup, evident for the high sucrose.
Sensory analysis was the final confirmation to recognize the honey
groups studied here, namely honey produced in combs by Apis
mellifera, fake honey, and honey produced in cerumen pots by
Geotrigona, Melipona, and Scaptotrigona. Chloroform extractions of
honey were also done to search lipophilic additives in NMR spectra.
This is a valuable contribution to protect honey consumers, and to
develop the beekeeping industry in Ecuador.
Abstract: This paper presents a study the effect of nose radius
(Rz-mm) on cutting force components and temperatures during the
machining simulation in an orthogonal cutting process for titanium
alloy (Ti-6Al-4V). The cutting process was performed at various
nose radiuses (Rz-mm) while the depth of cut (d-mm), feed rate (fmm/
tooth) and cutting speed (vc-m/ min) were remained constant.
The main cutting force (Fc), feed cutting force (Ft) and temperatures
were estimated by using finite element modeling (FEM) through
ABAQUS/EXPLICIT software and the simulation was developed the
two-dimension via an orthogonal cutting process during machining
titanium alloy (Ti-6Al-4V). The results led to the conclusion that the
nose radius (Rz-mm) has affected directly on the cutting force
components. However, temperature gave no indication or has no
significant relation with nose radius during machining titanium alloy
(Ti-6Al-4V). Hence, any increase or decrease in the nose radius (Rzmm)
during machining operation led to effect on the cutting forces
and thus it will be effective on surface finish, quality, and quantity of
products.
Abstract: An innovative flooring underlayment was produced
and tested. The composite system is made of common OSB boards
and a layer of eco-friendly non-cement gypsum based material
(GeoGypTM). It was found that the shear bond between the two
materials is sufficient to secure the composite interaction between the
two. The very high compressive strength and relatively high tensile
strength of the non-cement based component together with its high
modulus of elasticity provides enough strength and stiffness for the
composite product to cover wider spacing between the joists. The
initial findings of this study indicate that with joist spacing as wide as
800 mm, the flooring system provides enough strength without
compromising the serviceability requirements of the building codes.
Abstract: Scrubbing by a liquid spraying is one of the most
effective processes used for removal of fine particles and soluble
gas pollutants (such as SO2, HCl, HF) from the flue gas. There are
many configurations of scrubbers designed to provide contact
between the liquid and gas stream for effectively capturing
particles or soluble gas pollutants, such as spray plates, packed bed
towers, jet scrubbers, cyclones, vortex and venturi scrubbers. The
primary function of venturi scrubber is the capture of fine particles
as well as HCl, HF or SO2 removal with effect of the flue gas
temperature decrease before input to the absorption column. In this
paper, sulfur dioxide (SO2) from flue gas was captured using new
design replacing venturi scrubber (1st degree of wet scrubbing).
The flue gas was prepared by the combustion of the carbon
disulfide solution in toluene (1:1 vol.) in the flame in the reactor.
Such prepared flue gas with temperature around 150°C was
processed in designed laboratory O-element scrubber. Water was
used as absorbent liquid. The efficiency of SO2 removal, pressure
drop and temperature drop were measured on our experimental
device. The dependence of these variables on liquid-gas ratio was
observed. The average temperature drop was in the range from
150°C to 40°C. The pressure drop was increased with increasing of
a liquid-gas ratio, but no too much as for the common venturi
scrubber designs. The efficiency of SO2 removal was up to 70 %.
The pressure drop of our new designed wet scrubber is similar to
commonly used venturi scrubbers; nevertheless the influence of
amount of the liquid on pressure drop is not so significant.
Abstract: This paper is concerned with knowledge representation
and extraction of fuzzy if-then rules using Interval Type-2
Context-based Fuzzy C-Means clustering (IT2-CFCM) with the aid of
fuzzy granulation. This proposed clustering algorithm is based on
information granulation in the form of IT2 based Fuzzy C-Means
(IT2-FCM) clustering and estimates the cluster centers by preserving
the homogeneity between the clustered patterns from the IT2 contexts
produced in the output space. Furthermore, we can obtain the
automatic knowledge representation in the design of Radial Basis
Function Networks (RBFN), Linguistic Model (LM), and Adaptive
Neuro-Fuzzy Networks (ANFN) from the numerical input-output data
pairs. We shall focus on a design of ANFN in this paper. The
experimental results on an estimation problem of energy performance
reveal that the proposed method showed a good knowledge
representation and performance in comparison with the previous
works.
Abstract: This paper presents a part of the project solving which
is dedicated to the identification of the hazardous waste with the most
critical production within the Czech Republic with the aim to study
and find the optimal composition of the cement matrix that will
ensure maximum content disposal of chosen hazardous waste. In the
first stage of project solving – which represents this paper – a specific
hazardous waste was chosen, its properties were identified and
suitable solidification agents were chosen. Consequently
solidification formulas and testing methodology was proposed.