Abstract: A Laboratory-scale packed bed reactor with microbial
cellulose as the biofilm carrier was used to investigate the
denitrification of high-strength nitrate wastewater with specific
emphasis on the effect the nitrogen loading rate and hydraulic
retention time. Ethanol was added as a carbon source for
denitrification. As a result of this investigation, it was found that up
to 500 mg/l feed nitrate concentration the present system is able to
produce an effluent with nitrate content below 10 ppm at 3 h
hydraulic retention time. The highest observed denitrification rate
was 4.57 kg NO3-N/ (m3 .d) at a nitrate load of 5.64 kg NO3-
N/(m3 .d), and removal efficiencies higher than 90% were obtained
for loads up to 4.2 kg NO3-N/(m3 .d). A mass relation between COD
consumed and NO3-N removed around 2.82 was observed. This
continuous-flow bioreactor proved an efficient denitrification system
with a relatively low retention time.
Abstract: In recent years, Radio Frequency Identification (RFID)
is followed with interest by many researches, especially for the
purpose of indoor positioning as the innate properties of RFID are
profitable for achieving it. A lot of algorithms or schemes are proposed
to be used in the RFID-based positioning system, but most of them are
lack of environmental consideration and it induces inaccuracy of
application. In this research, a lot of algorithms and schemes of RFID
indoor positioning are discussed to see whether effective or not on
application, and some rules are summarized for achieving accurate
positioning. On the other hand, a new term “Noise Factor" is involved
to describe the signal loss between the target and the obstacle. As a
result, experimental data can be obtained but not only simulation; and
the performance of the positioning system can be expressed
substantially.
Abstract: One of the major disadvantages of the minimally
invasive surgery (MIS) is the lack of tactile feedback to the surgeon.
In order to identify and avoid any damage to the grasped complex
tissue by endoscopic graspers, it is important to measure the local
softness of tissue during MIS. One way to display the measured
softness to the surgeon is a graphical method. In this paper, a new
tactile sensor has been reported. The tactile sensor consists of an
array of four softness sensors, which are integrated into the jaws of a
modified commercial endoscopic grasper. Each individual softness
sensor consists of two piezoelectric polymer Polyvinylidene Fluoride
(PVDF) films, which are positioned below a rigid and a compliant
cylinder. The compliant cylinder is fabricated using a micro molding
technique. The combination of output voltages from PVDF films is
used to determine the softness of the grasped object. The theoretical
analysis of the sensor is also presented.
A method has been developed with the aim of reproducing the
tactile softness to the surgeon by using a graphical method. In this
approach, the proposed system, including the interfacing and the data
acquisition card, receives signals from the array of softness sensors.
After the signals are processed, the tactile information is displayed
by means of a color coding method. It is shown that the degrees of
softness of the grasped objects/tissues can be visually differentiated
and displayed on a monitor.
Abstract: The research was conducted with three replications as
“Randomized Block Design” in Konya-Turkey ecological conditions.
In the study, 16 of promising safflower lines (A8, E1, F4, F6, G16,
H14, I1), and 1 cultivar (Dinçer) were evaluated in 2008-09 growing
season. Some of the yield components such as plant height (cm), first
branch height (cm), number of branches per plant, 1000 seed weight
(g), seed yield (kg ha-1), oil content (%), oil yield (kg ha-1) were
determined. Winter sowing showed higher values than spring sowing.
The highest values were taken from Dinçer for plant height (86.7
cm), E1 (37.5 cm) for first branch height, F6 for number of branch
(11.6 per plant), I1 for number of head (24.9 per plant), A8 for 1000
seed weight (51.75 g), Dinçer for seed yield (2927.1 kg ha-1), oil
content (28.79 %) and also for oil yield (87.44 kg ha-1) respectively.
Abstract: Nowadays companies strive to survive in a
competitive global environment. To speed up product
development/modifications, it is suggested to adopt a collaborative
product development approach. However, despite the advantages of
new IT improvements still many CAx systems work separately and
locally. Collaborative design and manufacture requires a product
information model that supports related CAx product data models. To
solve this problem many solutions are proposed, which the most
successful one is adopting the STEP standard as a product data model
to develop a collaborative CAx platform. However, the improvement
of the STEP-s Application Protocols (APs) over the time, huge
number of STEP AP-s and cc-s, the high costs of implementation,
costly process for conversion of older CAx software files to the STEP
neutral file format; and lack of STEP knowledge, that usually slows
down the implementation of the STEP standard in collaborative data
exchange, management and integration should be considered. In this
paper the requirements for a successful collaborative CAx system is
discussed. The STEP standard capability for product data integration
and its shortcomings as well as the dominant platforms for supporting
CAx collaboration management and product data integration are
reviewed. Finally a platform named LAYMOD to fulfil the
requirements of CAx collaborative environment and integrating the
product data is proposed. The platform is a layered platform to enable
global collaboration among different CAx software
packages/developers. It also adopts the STEP modular architecture
and the XML data structures to enable collaboration between CAx
software packages as well as overcoming the STEP standard
limitations. The architecture and procedures of LAYMOD platform
to manage collaboration and avoid contradicts in product data
integration are introduced.
Abstract: Langmuir–Blodgett (LB) films of polyaniline (PANI) grown onto ITO coated glass substrates were utilized for the fabrication of Uric acid biosensor for efficient detection of uric acid by immobilizing Uricase via EDC–NHS coupling. The modified electrodes were characterized by atomic force microscopy (AFM). The response characteristics after immobilization of uricase were studied using cyclic voltammetry and electrochemical impedance spectroscopy techniques. The uricase/PANI/ITO/glass bioelectrode studied by CV and EIS techniques revealed detection of uric acid in a wide range of 0.05 mM to 1.0 mM, covering the physiological range in blood. A low Michaelis–Menten constant (Km) of 0.21 mM indicates the higher affinity of immobilized Uricase towards its analyte (uric acid). The fabricated uric acid biosensor based on PANI LB films exhibits excellent sensitivity of 0.21 mA/mM with a response time of 4 s, good reproducibility, long shelf life (8 weeks) and high selectivity.
Abstract: The applications on numbers are across-the-board that there is much scope for study. The chic of writing numbers is diverse and comes in a variety of form, size and fonts. Identification of Indian languages scripts is challenging problems. In Optical Character Recognition [OCR], machine printed or handwritten characters/numerals are recognized. There are plentiful approaches that deal with problem of detection of numerals/character depending on the sort of feature extracted and different way of extracting them. This paper proposes a recognition scheme for handwritten Hindi (devnagiri) numerals; most admired one in Indian subcontinent our work focused on a technique in feature extraction i.e. Local-based approach, a method using 16-segment display concept, which is extracted from halftoned images & Binary images of isolated numerals. These feature vectors are fed to neural classifier model that has been trained to recognize a Hindi numeral. The archetype of system has been tested on varieties of image of numerals. Experimentation result shows that recognition rate of halftoned images is 98 % compared to binary images (95%).
Abstract: Through inward perceptions, we intuitively expect
distributed software development to increase the risks associated with
achieving cost, schedule, and quality goals. To compound this
problem, agile software development (ASD) insists one of the main
ingredients of its success is cohesive communication attributed to
collocation of the development team. The following study identified
the degree of communication richness needed to achieve comparable
software quality (reduce pre-release defects) between distributed and
collocated teams. This paper explores the relevancy of
communication richness in various development phases and its
impact on quality. Through examination of a large distributed agile
development project, this investigation seeks to understand the levels
of communication required within each ASD phase to produce
comparable quality results achieved by collocated teams. Obviously,
a multitude of factors affects the outcome of software projects.
However, within distributed agile software development teams, the
mode of communication is one of the critical components required to
achieve team cohesiveness and effectiveness. As such, this study
constructs a distributed agile communication model (DAC-M) for
potential application to similar distributed agile development efforts
using the measurement of the suitable level of communication. The
results of the study show that less rich communication methods, in
the appropriate phase, might be satisfactory to achieve equivalent
quality in distributed ASD efforts.
Abstract: An experiment was conducted in October 2008 due the ability replacement plant associate biofertilizers by chemical fertilizers and the qualifying rate of chemical N fertilizers at the moment of using this biofertilizers and the interaction of this biofertilizer on each other. This field experiment has been done in Persepolis (Throne of Jamshid) and arrange by using factorial with the basis of randomized complete block design, in three replication Azespirilium SP bacteria has been admixed with consistence 108 cfu/g and inoculated with seeds of wheat, The streptomyces SP has been used in amount of 550 gr/ha and concatenated on clay and for the qualifying range of chemical fertilizer 4 level of N chemical fertilizer from the source of urea (N0=0, N1=60, N2=120, N3=180) has been used in this experiment. The results indicated there were Significant differences between levels of Nitrogen fertilizer in the entire characteristic which has been measured in this experiment. The admixed Azespirilium SP showed significant differences between their levels in the characteristics such as No. of fertile ear, No. of grain per ear, grain yield, grain protein percentage, leaf area index and the agronomic fertilizer use efficiency. Due the interaction streptomyses with Azespirilium SP bacteria this actinomycet didn-t show any statistically significant differences between it levels.
Abstract: Field Association (FA) terms are a limited set of discriminating terms that give us the knowledge to identify document fields which are effective in document classification, similar file retrieval and passage retrieval. But the problem lies in the lack of an effective method to extract automatically relevant Arabic FA Terms to build a comprehensive dictionary. Moreover, all previous studies are based on FA terms in English and Japanese, and the extension of FA terms to other language such Arabic could be definitely strengthen further researches. This paper presents a new method to extract, Arabic FA Terms from domain-specific corpora using part-of-speech (POS) pattern rules and corpora comparison. Experimental evaluation is carried out for 14 different fields using 251 MB of domain-specific corpora obtained from Arabic Wikipedia dumps and Alhyah news selected average of 2,825 FA Terms (single and compound) per field. From the experimental results, recall and precision are 84% and 79% respectively. Therefore, this method selects higher number of relevant Arabic FA Terms at high precision and recall.
Abstract: Ultra-wide band (UWB) communication is one of
the most promising technologies for high data rate wireless networks
for short range applications. This paper proposes a blind channel
estimation method namely IMM (Interactive Multiple Model) Based
Kalman algorithm for UWB OFDM systems. IMM based Kalman
filter is proposed to estimate frequency selective time varying
channel. In the proposed method, two Kalman filters are concurrently
estimate the channel parameters. The first Kalman filter namely
Static Model Filter (SMF) gives accurate result when the user is static
while the second Kalman filter namely the Dynamic Model Filter
(DMF) gives accurate result when the receiver is in moving state. The
static transition matrix in SMF is assumed as an Identity matrix
where as in DMF, it is computed using Yule-Walker equations. The
resultant filter estimate is computed as a weighted sum of individual
filter estimates. The proposed method is compared with other existing
channel estimation methods.
Abstract: Adopting Zakowski-s upper approximation operator
C and lower approximation operator C, this paper investigates
granularity-wise separations in covering approximation spaces. Some
characterizations of granularity-wise separations are obtained by
means of Pawlak rough sets and some relations among granularitywise
separations are established, which makes it possible to research
covering approximation spaces by logical methods and mathematical
methods in computer science. Results of this paper give further
applications of Pawlak rough set theory in pattern recognition and
artificial intelligence.
Abstract: The evaluation of the question answering system is a major research area that needs much attention. Before the rise of domain-oriented question answering systems based on natural language understanding and reasoning, evaluation is never a problem as information retrieval-based metrics are readily available for use. However, when question answering systems began to be more domains specific, evaluation becomes a real issue. This is especially true when understanding and reasoning is required to cater for a wider variety of questions and at the same time achieve higher quality responses The research in this paper discusses the inappropriateness of the existing measure for response quality evaluation and in a later part, the call for new standard measures and the related considerations are brought forward. As a short-term solution for evaluating response quality of heterogeneous systems, and to demonstrate the challenges in evaluating systems of different nature, this research presents a black-box approach using observation, classification scheme and a scoring mechanism to assess and rank three example systems (i.e. AnswerBus, START and NaLURI).
Abstract: Investigations of the unimolecular decomposition of
vinyl ethyl ether (VEE), vinyl propyl ether (VPE) and vinyl butyl
ether (VBE) have shown that activation of the molecule of a ether
results in formation of a cyclic construction - the transition state (TS),
which may lead to the displacement of the thermodynamic
equilibrium towards the reaction products. The TS is obtained by
applying energy minimization relative to the ground state of an ether
under the program MM2 when taking into account the hydrogen bond
formation between a hydrogen atom of alkyl residue and the extreme
atom of carbon of the vinyl group. The dissociation of TS up to the
products is studied by energy minimization procedure using the
mathematical program Gaussian. The obtained calculation data for
VEE testify that the decomposition of this ether may be conditioned
by hydrogen bond formation for two possible versions: when α- or β-
hydrogen atoms of the ethyl group are bound to carbon atom of the
vinyl group. Applying the same calculation methods to other ethers
(VPE and VBE) it is shown that only in the case of hydrogen bonding
between α-hydrogen atom of the alkyl residue and the extreme atom
of carbon of the vinyl group (αH---C) results in decay of theses
ethers.
Abstract: This paper presents a robust vehicle detection approach using Haar-like feature. It is possible to get a strong edge feature from this Haar-like feature. Therefore it is very effective to remove the shadow of a vehicle on the road. And we can detect the boundary of vehicles accurately. In the paper, the vehicle detection algorithm can be divided into two main steps. One is hypothesis generation, and the other is hypothesis verification. In the first step, it determines vehicle candidates using features such as a shadow, intensity, and vertical edge. And in the second step, it determines whether the candidate is a vehicle or not by using the symmetry of vehicle edge features. In this research, we can get the detection rate over 15 frames per second on our embedded system.
Abstract: Air conditioning is mainly to be used as human
comfort medium. It has been use more often in country in which the
daily temperatures are high. In scientific, air conditioning is defined
as a process of controlling the moisture, cooling, heating and cleaning
air. Without proper estimation of cooling load, big amount of waste
energy been used because of unsuitable of air conditioning system are
not considering to overcoming heat gains from surrounding. This is
due to the size of the room is too big and the air conditioning has to
use more energy to cool the room and the air conditioning is too
small for the room. The studies are basically to develop a program to
calculate cooling load. Through this study it is easy to calculate
cooling load estimation. Furthermore it-s help to compare the cooling
load estimation by hourly and yearly. Base on the last study that been
done, the developed software are not user-friendly. For individual
without proper knowledge of calculating cooling load estimation
might be problem. Easy excess and user-friendly should be the main
objective to design something. This program will allow cooling load
able be estimate by any users rather than estimation by using rule of
thumb. Several of limitation of case study is judged to sure it-s
meeting to Malaysia building specification. Finally validation is done
by comparison manual calculation and by developed program.
Abstract: Indium-tin oxide films are deposited by low plasma
temperature RF sputtering on highly flexible modification of glycol
polyethyleneterephtalate substrates. The produced layers are
characterized with transparency over 82 % and sheet resistance of
86.9 Ω/square. The film’s conductivity was further improved by
additional UV illumination from light source (365 nm), having power
of 250 W. The influence of the UV exposure dose on the structural
and electro-optical properties of ITO was investigated. It was
established that the optimum time of illumination is 10 minutes and
further UV treatment leads to polymer substrates degradation.
Structural and bonds type analysis show that at longer treatment
carbon atoms release and diffuse into ITO films, which worsen their
electrical behavior. For the optimum UV dose the minimum sheet
resistance was measured to be 19.2 Ω/square, and the maximum
transparency remained almost unchanged – above 82 %.
Abstract: The pulp and paper mill effluent is one of the high
polluting effluent amongst the effluents obtained from polluting
industries. All the available methods for treatment of pulp and paper
mill effluent have certain drawbacks. The coagulation is one of the
cheapest process for treatment of various organic effluents. Thus, the
removal of chemical oxygen demand (COD) and colour of paper mill
effluent is studied using coagulation process. The batch coagulation
process was performed using various coagulants like: aluminium
chloride, poly aluminium chloride and copper sulphate. The initial
pH of the effluent (Coagulation pH) has tremendous effect on COD
and colour removal. Poly aluminium chloride (PAC) as coagulant
reduced COD to 84 % and 92 % of colour was removed at an
optimum pH 5 and coagulant dose of 8 ml l-1. With aluminium
chloride at an optimum pH = 4 and coagulant dose of 5 g l-1, 74 %
COD and 86 % colour removal were observed. The results using
copper sulphate as coagulant (a less commercial coagulant) were
encouraging. At an optimum pH 6 and mass loading of 5 g l-1, 76 %
COD reduction and 78 % colour reduction were obtained. It was also
observed that after addition of coagulant, the pH of the effluent
decreases. The decrease in pH was highest for AlCl3, which was
followed by PAC and CuSO4. Significant amount of COD reductions
was obtained by coagulation process. Since the coagulation process
is the first stage for treatment of effluent and some of the coagulant
cations usually remain in the treated effluents. Thus, cation like
copper may be one of the good catalyst for second stage of treatment
process like wet oxidation. The copper has been found to be good
oxidation catalyst then iron and aluminum.
Abstract: The fundamental aim of extended expansion concept is
to achieve higher work done which in turn leads to higher thermal
efficiency. This concept is compatible with the application of
turbocharger and LHR engine. The Low Heat Rejection engine was
developed by coating the piston crown, cylinder head inside with
valves and cylinder liner with partially stabilized zirconia coating of
0.5 mm thickness. Extended expansion in diesel engines is termed as
Miller cycle in which the expansion ratio is increased by reducing the
compression ratio by modifying the inlet cam for late inlet valve
closing. The specific fuel consumption reduces to an appreciable level
and the thermal efficiency of the extended expansion turbocharged
LHR engine is improved.
In this work, a thermodynamic model was formulated and
developed to simulate the LHR based extended expansion
turbocharged direct injection diesel engine. It includes a gas flow
model, a heat transfer model, and a two zone combustion model. Gas
exchange model is modified by incorporating the Miller cycle, by
delaying inlet valve closing timing which had resulted in considerable
improvement in thermal efficiency of turbocharged LHR engines. The
heat transfer model, calculates the convective and radiative heat
transfer between the gas and wall by taking into account of the
combustion chamber surface temperature swings. Using the two-zone
combustion model, the combustion parameters and the chemical
equilibrium compositions were determined. The chemical equilibrium
compositions were used to calculate the Nitric oxide formation rate by
assuming a modified Zeldovich mechanism. The accuracy of this
model is scrutinized against actual test results from the engine. The
factors which affect thermal efficiency and exhaust emissions were
deduced and their influences were discussed. In the final analysis it is
seen that there is an excellent agreement in all of these evaluations.
Abstract: In this paper, we present an innovative scheme of
blindly extracting message bits from an image distorted by an attack.
Support Vector Machine (SVM) is used to nonlinearly classify the
bits of the embedded message. Traditionally, a hard decoder is used
with the assumption that the underlying modeling of the Discrete
Cosine Transform (DCT) coefficients does not appreciably change.
In case of an attack, the distribution of the image coefficients is
heavily altered. The distribution of the sufficient statistics at the
receiving end corresponding to the antipodal signals overlap and a
simple hard decoder fails to classify them properly. We are
considering message retrieval of antipodal signal as a binary
classification problem. Machine learning techniques like SVM is
used to retrieve the message, when certain specific class of attacks is
most probable. In order to validate SVM based decoding scheme, we
have taken Gaussian noise as a test case. We generate a data set using
125 images and 25 different keys. Polynomial kernel of SVM has
achieved 100 percent accuracy on test data.