Abstract: The field of instrumentation electronics is undergoing
an explosive growth, due to its wide range of applications. The
proliferation of electrical devices in a close working proximity can
negatively influence each other’s performance. The degradation in
the performance is due to electromagnetic interference (EMI). This paper investigates the negative effects of electromagnetic
interference originating in the General Purpose Interface Bus (GPIB)
control-network of the AC-DC transfer measurement system.
Remedial measures of reducing measurement errors and failure of
range of industrial devices due to EMI have been explored. The ACDC
transfer measurement system was analysed for the commonmode
(CM) EMI effects. Further investigation of coupling path as
well as much accurate identification of noise propagation mechanism
has been outlined. To prevent the occurrence of common-mode
(ground loops) which was identified between the GPIB system
control circuit and the measurement circuit, a microcontroller-driven
GPIB switching isolator device was designed, prototyped,
programmed and validated. This mitigation technique has been
explored to reduce EMI effectively.
Abstract: The focus of this study was to determine the factors associated with the use of substances for sport performance of youth in Lagos state sport. Questionnaire was the instrument used for the study. Descriptive research method was used. The estimated population for the study was 2000 sport men and women. The sample size was 200 respondents for purposive sampling techniques were used. The instrument was validated in it content and constructs value. The instrument was administered with the assistance of the coaches. Same 200 copies administered were returned. The data obtained was analysed using simple percentage and chi-square (x2) for stated hypothesis at 0.05 level of significance. The finding reveal that sport injuries exercise induced and anaphylaxis and asthma and feeling of loss of efficacy associated with alcohol used on sport performance among the users of substances. Alcohol users are recommended to partake in sport like swimming, basketball and volleyball because they have space of time for resting while at play. Government should be fully in charge of the health of sport men and women.
Abstract: In this research, we propose to conduct diagnostic and
predictive analysis about the key factors and consequences of urban
population relocation. To achieve this goal, urban simulation models
extract the urban development trends as land use change patterns from
a variety of data sources. The results are treated as part of urban big
data with other information such as population change and economic
conditions. Multiple data mining methods are deployed on this data to
analyze nonlinear relationships between parameters. The result
determines the driving force of population relocation with respect to
urban sprawl and urban sustainability and their related parameters.
This work sets the stage for developing a comprehensive urban
simulation model for catering to specific questions by targeted users. It
contributes towards achieving sustainability as a whole.
Abstract: In this paper, an Infinite Impulse Response (IIR) filter
has been designed and simulated on an Field Programmable Gate
Arrays (FPGA). The implementation is based on Multiply Add and
Accumulate (MAC) algorithm which uses multiply operations for
design implementation. Parallel Pipelined structure is used to
implement the proposed IIR Filter taking optimal advantage of the
look up table of target device. The designed filter has been
synthesized on Digital Signal Processor (DSP) slice based FPGA to
perform multiplier function of MAC unit. The DSP slices are useful
to enhance the speed performance. The proposed design is simulated
with Matlab, synthesized with Xilinx Synthesis Tool, and
implemented on FPGA devices. The Virtex 5 FPGA based design can
operate at an estimated frequency of 81.5 MHz as compared to 40.5
MHz in case of Spartan 3 ADSP based design. The Virtex 5 based
implementation also consumes less slices and slice flip flops of target
FPGA in comparison to Spartan 3 ADSP based implementation to
provide cost effective solution for signal processing applications.
Abstract: Earth structures constructed of marine clay soils have
tendency to crack. In order to improve the flexural strength and
brittleness, a technique of mixing short fibers is introduced to the soil
lime mixture. Coir fiber was used in this study as reinforcing
elements. An experimental investigation consisting primarily of
flexural tensile tests was conducted to examine the influence of coir
fibers on the flexural behaviour of the reinforced soils. The test
results that the coir fibers were effective in improving the flexural
strength and Young’s modulus of all soils examined and ductility
after peak strength for reinforced marine clay soil treated by lime. 5%
lime treated soil and 1% coir fiber reinforced soil specimens’
demonstrated good strength and durability when submerged in water
and retained 45% of their air-cured strengths.
Abstract: The current web has become a modern encyclopedia,
where people share their thoughts and ideas on various topics around
them. This kind of encyclopedia is very useful for other people who
are looking for answers to their questions. However, with the
growing popularity of social networking and blogging and ever
expanding network services, there has also been a growing diversity
of technologies along with a different structure of individual web
sites. It is therefore difficult to directly find a relevant answer for a
common Internet user. This paper presents a web application for the
real-time end-to-end analysis of selected Internet trends where the
trend can be whatever the people post online. The application
integrates fully configurable tools for data collection and analysis
using selected webometric algorithms, and for its chronological
visualization to user. It can be assumed that the application facilitates
the users to evaluate the quality of various products that are
mentioned online.
Abstract: Dietary cholesterol has elicited the most public
interest as it relates with coronary heart disease. Thus, humans have
been paying more attention to health, thereby reducing consumption
of cholesterol enriched food. Egg is considered as one of the major
sources of human dietary cholesterol. However, an alternative way to
reduce the potential cholesterolemic effect of eggs is to modify the
fatty acid composition of the yolk. The effect of palm oil (PO),
soybean oil (SO), sesame seed oil (SSO) and fish oil (FO)
supplementation in the diets of layers on egg yolk fatty acid,
cholesterol, egg production and egg quality parameters were
evaluated in a 42-day feeding trial. One hundred and five Isa Brown
laying hens of 34 weeks of age were randomly distributed into seven
groups of five replicates and three birds per replicate in a completely
randomized design. Seven corn-soybean basal diets (BD) were
formulated: BD+No oil (T1), BD+1.5% PO (T2), BD+1.5% SO (T3),
BD+1.5% SSO (T4), BD+1.5% FO (T5), BD+0.75% SO+0.75% FO
(T6) and BD+0.75% SSO+0.75% FO (T7). Five eggs were randomly
sampled at day 42 from each replicate to assay for the cholesterol,
fatty acid profile of egg yolk and egg quality assessment. Results
showed that there were no significant (P>0.05) differences observed
in production performance, egg cholesterol and egg quality
parameters except for yolk height, albumen height, yolk index, egg
shape index, haugh unit, and yolk colour. There were no significant
differences (P>0.05) observed in total cholesterol, high density
lipoprotein and low density lipoprotein levels of egg yolk across the
treatments. However, diets had effect (P
Abstract: The number and adequacy of Performance-Indicators
(PIs) for organisational purposes are core to the success of
organisations and a major concern to the sponsor of this research.
This assignment developed a procedure to improve a firm’s
performance assessment system, by identifying two key-PIs out of 28
initial ones, and by setting criteria and their relative importance to
validate and rank the adequacy and the right number of operational
metrics. The Analytical-Hierarchy-Process was used with a synthesismethod
to treat data coming from the management inquiries.
Although organisational alignment has been achieved, business
processes should also be targeted and PIs continuously revised.
Abstract: In this corporate world, the technology of Web
services has grown rapidly and its significance for the development
of web based applications gradually rises over time. The success of
Business to Business integration rely on finding novel partners and
their services in a global business environment. However, the
selection of the most suitable Web service from the list of services
with the identical functionality is more vital. The satisfaction level of
the customer and the provider’s reputation of the Web service are
primarily depending on the range it reaches the customer’s
requirements. In most cases, the customer of the Web service feels
that he is spending for the service which is undelivered. This is
because the customer always thinks that the real functionality of the
web service is not reached. This will lead to change of the service
frequently. In this paper, a framework is proposed to evaluate the
Quality of Service (QoS) and its cost that makes the optimal
correlation between each other. In addition, this research work
proposes some management decision against the functional deviancy
of the web service that is guaranteed at time of selection.
Abstract: The paper deals with possibilities of increase train
capacity by using a new type of railway wagon. In the first part is
created a mathematical model to calculate the capacity of the train.
The model is based on the main limiting parameters of the train -
maximum number of axles per train, maximum gross weight of train,
maximum length of train and number of TEUs per one wagon. In the
second part is the model applied to four different model trains with
different composition of the train set and three different average
weights of TEU and a train consisting of a new type of wagons. The
result is to identify where the carrying capacity of the original trains
is higher, respectively less than a capacity of train consisting of a new
type of wagons.
Abstract: Weak damping of low frequency oscillations is a frequent phenomenon in electrical power systems. These frequencies can be damped by power system stabilizers. Unified power flow controller (UPFC), as one of the most important FACTS devices, can be applied to increase the damping of power system oscillations and the more effect of this controller on increasing the damping of oscillations depends on its proper placement in power systems. In this paper, a technique based on controllability is proposed to select proper location of UPFC and the best input control signal in order to enhance damping of power oscillations. The effectiveness of the proposed technique is demonstrated in IEEE 9 bus power system.
Abstract: In this work, by replacing the traditional solid spokes with colloidal spokes, a vehicle wheel with a built-in suspension structure is proposed. Following the background and description of the wheel system, firstly, a vibration model of the wheel equipped with colloidal spokes is proposed, and based on such model the equivalent damping coefficients and spring constants are identified. Then, a modified model of a quarter-vehicle moving on a rough pavement is proposed in order to estimate the transmissibility of vibration from the road roughness to vehicle body. In the end, the optimal design of the colloidal spokes and the optimum number of colloidal spokes are decided in order to minimize the transmissibility of vibration, i.e., to maximize the ride comfort of the vehicle.
Abstract: One of the main purposes of designing bucklingrestrained
braces is the fact that the entire lateral load is wasted by
the braces, the entire gravitational load is moved to the foundation
through the beams, and the columns can be moved to the foundation.
In other words, braces are designed for bearing lateral load. In the
implementation of the structure, it should be noted that the
implementation of various parts of the structure must be conducted in
such a way that the buckling-restrained braces would not bear the
gravitational load. Moreover, this type of brace has been investigated
under impact loading, and the design goals of designing method
(direct motion) are controlled under impact loading. The results of
dynamic analysis are shown as the relocation charts of the floors and
switch between the floors. Finally, the results are compared with each
other.
Abstract: This work aims to investigate the structure–property
relationship in ternary nanocomposites consisting of polypropylene
as the matrix, polyamide 66 as the minor phase and treated nanoclay
DELLITE 67G as the reinforcement. All PP/PA66/Nanoclay systems
with polypropylene grafted maleic anhydride PP-g-MAH as a
compatibilizer were prepared via melt compounding and
characterized in terms of nanoclay content. Morphological structure
was investigated by scanning electron microscopy. The rheological
behavior of the nanocomposites was determined by various methods,
viz melt flow index (MFI) and parallel plate rheological
measurements. The PP/PP-g-MAH/PA66 nanocomposites showed a homogeneous
morphology supporting the compatibility improvement between PP,
PA66, and nanoclay. SEM results revealed the formation of
nanocomposites as the nanoclay was intercalated and exfoliated. In
the ternary nanocomposites, the rheological behavior showed that, the
complex viscosity is increased with increasing the nanoclay. The results showed that the use of nanoclay affects the variations
of storage modulus (G′), loss modulus (G″) and the melt elasticity.
Abstract: We investigate the large scale of networks in the
context of network survivability under attack. We use appropriate
techniques to evaluate and the attacker-based- and the defenderbased-
network survivability. The attacker is unaware of the operated
links by the defender. Each attacked link has some pre-specified
probability to be disconnected. The defender choice is so that to
maximize the chance of successfully sending the flow to the
destination node. The attacker however will select the cut-set with
the highest chance to be disabled in order to partition the network.
Moreover, we extend the problem to the case of selecting the best p
paths to operate by the defender and the best k cut-sets to target by
the attacker, for arbitrary integers p,k>1. We investigate some
variations of the problem and suggest polynomial-time solutions.
Abstract: One of prevailing modes of finance in emerging
Islamic banking system is Murabah’a. It means a financial dealing or
transaction in which seller tells cost of the goods to be sold to buyer.
Otherwise, the transaction would become invalid. In this mainstream,
import Murabah’a transaction is divergent in such a way that the cost
is not recognized and identified due to execution of import
transaction in foreign currency i.e. US Dollar and the next transaction
of Murabaha’a with the client is executed in local currency. Since this
transaction is executed in dual currency i.e. bank pays supplier in
foreign currency and executes Murabah’a with its client in local
currency and it is not allowed in according to Islamic Injunctions as
mentioned in hadith narrated by Hazrat Ibn-e-Umar (May Allah be
pleased with them) used to sell his camels with Dirhams and take
dinars instead and vice versa. Upon revealing before the Prophet
(Peace be upon him), he was advised that it must not be contingent in
the agreement and the ready rate would be applied and possession of
one of the consideration is compulsory. The solution in this regard is
that the import Murabah’a transaction should be in single currency
However, other currency can be paid in payment at the time of
payment in a very indispensable situation provided that ready rate
would be applied. Moreover, some of other solutions have also been
given in this regard.
Abstract: This paper aims to analysis the behavior of DC corona
discharge in wire-to-plate electrostatic precipitators (ESP). Currentvoltage
curves are particularly analyzed. Experimental results show
that discharge current is strongly affected by the applied voltage. The proposed method of current identification is to use the method
of least squares. Least squares problems that of into two categories:
linear or ordinary least squares and non-linear least squares,
depending on whether or not the residuals are linear in all unknowns.
The linear least-squares problem occurs in statistical regression
analysis; it has a closed-form solution. A closed-form solution (or
closed form expression) is any formula that can be evaluated in a
finite number of standard operations. The non-linear problem has no
closed-form solution and is usually solved by iterative.
Abstract: Low density polyethylene (LDPE) nanocomposites
with 3, 5 and 7 wt. % cobalt ferrite (CoFe2O4) nanopowder fabricated
with extrusion mixing and followed up by hot press to reach compact
samples. The transmission/reflection measurements were carried out
with a network analyzer in the frequency range of 8-12 GHz. By
increasing the percent of CoFe2O4 nanopowder, reflection loss (S11)
increases, while transferring loss (S21) decreases. Reflectivity (R)
calculations made using S11 and S21. Increase in percent of CoFe2O4
nanopowder up to 7 wt. % in composite leaded to higher reflectivity
amount, and revealed that increasing the percent of CoFe2O4
nanopowder up to 7 wt. % leads to further microwave absorption in
8-12 GHz range.
Abstract: In the last decades, psychological tests have been
gaining in popularity as a method used for evaluating personnel, and
they bring consulting companies solid profits rising by up to 10%
each year. The market is offering a growing range of tools for the
assessment of personality. Tests are used in organizations mainly in
the recruitment and selection of staff. This paper is an attempt to
initially diagnose the state of the use of psychological tests in Polish
companies on the basis of empirical research.
Abstract: Advances in spatial and spectral resolution of satellite
images have led to tremendous growth in large image databases. The
data we acquire through satellites, radars, and sensors consists of
important geographical information that can be used for remote
sensing applications such as region planning, disaster management.
Spatial data classification and object recognition are important tasks
for many applications. However, classifying objects and identifying
them manually from images is a difficult task. Object recognition is
often considered as a classification problem, this task can be
performed using machine-learning techniques. Despite of many
machine-learning algorithms, the classification is done using
supervised classifiers such as Support Vector Machines (SVM) as the
area of interest is known. We proposed a classification method,
which considers neighboring pixels in a region for feature extraction
and it evaluates classifications precisely according to neighboring
classes for semantic interpretation of region of interest (ROI). A
dataset has been created for training and testing purpose; we
generated the attributes by considering pixel intensity values and
mean values of reflectance. We demonstrated the benefits of using
knowledge discovery and data-mining techniques, which can be on
image data for accurate information extraction and classification from
high spatial resolution remote sensing imagery.