Abstract: In this paper we have proposed a novel dynamic least cost multicast routing protocol using hybrid genetic algorithm for IP networks. Our protocol finds the multicast tree with minimum cost subject to delay, degree, and bandwidth constraints. The proposed protocol has the following features: i. Heuristic local search function has been devised and embedded with normal genetic operation to increase the speed and to get the optimized tree, ii. It is efficient to handle the dynamic situation arises due to either change in the multicast group membership or node / link failure, iii. Two different crossover and mutation probabilities have been used for maintaining the diversity of solution and quick convergence. The simulation results have shown that our proposed protocol generates dynamic multicast tree with lower cost. Results have also shown that the proposed algorithm has better convergence rate, better dynamic request success rate and less execution time than other existing algorithms. Effects of degree and delay constraints have also been analyzed for the multicast tree interns of search success rate.
Abstract: A series of Ti based shape memory alloys with
composition of Ti50Ni49Cr1, Ti50Ni47Cr3 and Ti50Ni45Cr5 were
developed by vacuum arc-melting under a purified argon atmosphere.
The histometric and corrosion evaluation of Ti-Ni-Cr shape memory
alloys have been considered in this research work. The alloys were
developed by vacuum arc melting and implanted subcutaneously in
rabbits for 4, 8 and 12 weeks. Metallic implants were embedded in
order to determine the outcome of implantation on histometric and
corrosion evaluation of Ti-Ni-Cr metallic strips. Encapsulating
membrane formation around the alloys was minimal in the case of all
materials. After histomorphometric analyses it was possible to
demonstrate that there were no statistically significant differences
between the materials. Corrosion rate was also determined in this
study which is within acceptable range. The results showed the Ti-
Ni-Cr alloy was neither cytotoxic, nor have any systemic reaction on
living system in any of the test performed. Implantation shows good
compatibility and a potential of being used directly in vivo system.
Abstract: Martensitic stainless steels have been extensively used for their good corrosion resistance and better mechanical properties. Heat treatment was suggested as one of the most excellent ways to this regard; hence, it affects the microstructure, mechanical and corrosion properties of the steel. In the current research work the microstructural changes and corrosion behavior in an AISI 420A stainless steel exposed to temperatures in the 980-1035oC range were investigated. The heat treatment is carried out in vacuum furnace within the said temperature range. The quenching of the samples was carried out in oil, brine and water media. The formation and stability of passive film was studied by Open Circuit Potential, Potentiodynamic polarization and Electrochemical Scratch Tests. The Electrochemical Impedance Spectroscopy results simulated with Equivalent Electrical Circuit suggested bilayer structure of outer porous and inner barrier oxide films. The quantitative data showed thick inner barrier oxide film retarded electrochemical reactions. Micrographs of the quenched samples showed sigma and chromium carbide phases which prove the corrosion resistance of steel alloy.
Abstract: This research aims at modeling and simulating the effects of nanofluids on cylindrical heat pipes thermal performance using the ANSYS-FLUENT CFD commercial software. The heat pipe outer wall temperature distribution, thermal resistance, liquid pressure and axial velocity in presence of suspended nano-scaled solid particle (i.e. Cu, Al2O3 and TiO2) within the fluid (water) were investigated. The effect of particle concentration and size were explored and it is concluded that the thermal performance of the heat pipe is improved when using nanofluid as the system working fluid. Additionally, it was observed that the thermal resistance of the heat pipe drops as the particle concentration level increases and particle radius decreases.
Abstract: This research investigates the factors that influence moral judgments when dealing with ethical dilemmas in the organizational context. It also investigates the antecedents of individual ethical ideology (idealism and relativism). A mixed method study, which combines qualitative (field study) and quantitative (survey) approaches, was used in this study. An initial model was developed first, which was then fine-tuned based on field studies. Data were collected from managers in Malaysian large organizations. The results of this study reveal that in-group collectivism culture, power distance culture, parental values, and religiosity were significant as antecedents of ethical ideology. However, direct effects of these variables on moral judgment were not significant. Furthermore, the results of this study confirm the significant effects of ethical ideology on moral judgment. This study provides valuable insight into evaluating the validity of existing theory as proposed in the literature and offers significant practical implications.
Abstract: Located within the tropical belt region, there are
certain rules which should implemented in creating a passive
sustainable housing design in Malaysia. Traditional Malay house
possess a strong character with certain special spaces to create a
sustainable house which suit to the tropical climate in Malaysia. One
of the special space known as verandah or serambi gantung, create
various advantages in solving various issues. However, this special
space is not extremely being applied currently which produce major
issues in term of social and environmental aspects. Hence, this
phenomena create a negative impact to the occupant while Malaysia
already has a best housing design previously. Therefore, this paper
aims to explore both of the main issues mentioned above and reveal
the advantages of implementing verandah into passive sustainable
housing design in Malaysia. A systematic literature review is the
main methodology in this research to identify the various advantages
about verandah.. The study reveals that verandah is the best solution
in term of social and environmental issues and should be
implemented in current housing design in Malaysia.
Abstract: The restoration of extinct ponds is considered as one
of ways to gain new retention capacities for water which is getting
much more important issue with respect to expected impacts of a
climate change. However, there are also other pressures on the
landscape which must be all taken into consideration when making a
decision on the possible restoration of extinct ponds. The research
presented here focuses besides others on the restoration of former
ponds which could be important for both the flood protection and
drought impacts prevention. The first step of the methodology
development for the assessment of such areas is the assessment of
their present state. In this paper, the results of land use types
assessment for 22 localities are presented. These results confirm the
assumption that the most present land use type in such areas is the
permanent grassland. However, the spectra of land use types present
in extinct pond areas is very diverse and include besides others also
airport areas and industry.
Abstract: Fully customized hardware based technology provides high performance and low power consumption by specializing the tasks in hardware but lacks design flexibility since any kind of changes require re-design and re-fabrication. Software based solutions operate with software instructions due to which a great flexibility is achieved from the easy development and maintenance of the software code. But this execution of instructions introduces a high overhead in performance and area consumption. In past few decades the reconfigurable computing domain has been introduced which overcomes the traditional trades-off between flexibility and performance and is able to achieve high performance while maintaining a good flexibility. The dramatic gains in terms of chip performance and design flexibility achieved through the reconfigurable computing systems are greatly dependent on the design of their computational units being integrated with reconfigurable logic resources. The computational unit of any reconfigurable system plays vital role in defining its strength. In this research paper an RFU based computational unit design has been presented using the tightly coupled, multi-threaded reconfigurable cores. The proposed design has been simulated for VLIW based architectures and a high gain in performance has been observed as compared to the conventional computing systems.
Abstract: Coal fly ash (CFA) generated by coal-based thermal
power plants is mainly composed of quartz, mullite, and unburned
carbon. In this study, the effect of unburned carbon on CFA toward
its adsorption capacity was investigated. CFA with various carbon
content was obtained by refluxing it with sulfuric acid having various
concentration at various temperature and reflux time, by heating at
400-800°C, and by sieving into 100-mesh in particle size. To
evaluate the effect of unburned carbon on CFA toward its adsorption
capacity, adsorption of methyl violet solution with treated CFA was
carried out. The research shows that unburned carbon leads to
adsorption capacity decrease. The highest adsorption capacity of
treated CFA was found 5.73 x 10-4mol.g-1.
Abstract: One of the main environmental problems which affect extensive areas in the world is soil salinity. Traditional data collection methods are neither enough for considering this important environmental problem nor accurate for soil studies. Remote sensing data could overcome most of these problems. Although satellite images are commonly used for these studies, however there are still needs to find the best calibration between the data and real situations in each specified area. Neyshaboor area, North East of Iran was selected as a field study of this research. Landsat satellite images for this area were used in order to prepare suitable learning samples for processing and classifying the images. 300 locations were selected randomly in the area to collect soil samples and finally 273 locations were reselected for further laboratory works and image processing analysis. Electrical conductivity of all samples was measured. Six reflective bands of ETM+ satellite images taken from the study area in 2002 were used for soil salinity classification. The classification was carried out using common algorithms based on the best composition bands. The results showed that the reflective bands 7, 3, 4 and 1 are the best band composition for preparing the color composite images. We also found out, that hybrid classification is a suitable method for identifying and delineation of different salinity classes in the area.
Abstract: The need to evaluate and understand the natural
drainage pattern in a flood prone, and fast developing environment is
of paramount importance. This information will go a long way to
help the town planners to determine the drainage pattern, road
networks and areas where prominent structures are to be located. This
research work was carried out with the aim of studying the Bayelsa
landscape topography using digitized topographic information, and to
model the natural drainage flow pattern that will aid the
understanding and constructions of workable drainages. To achieve
this, digitize information of elevation and coordinate points were
extracted from a global imagery map. The extracted information was
modeled into 3D surfaces. The result revealed that the average
elevation for Bayelsa State is 12 m above sea level. The highest
elevation is 28 m, and the lowest elevation 0 m, along the coastline.
In Yenagoa the capital city of Bayelsa were a detail survey was
carried out showed that average elevation is 15 m, the highest
elevation is 25 m and lowest is 3 m above the mean sea level. The
regional elevation in Bayelsa, showed a gradation decrease from the
North Eastern zone to the South Western Zone. Yenagoa showed an
observed elevation lineament, were low depression is flanked by high
elevation that runs from the North East to the South west. Hence,
future drainages in Yenagoa should be directed from the high
elevation, from South East toward the North West and from the
North West toward South East, to the point of convergence which is
at the center that flows from South East toward the North West.
Bayelsa when considered on a regional Scale, the flow pattern is from
the North East to the South West, and also North South. It is
recommended that in the event of any large drainage construction at
municipal scale, it should be directed from North East to the South
West or from North to South. Secondly, detail survey should be
carried out to ascertain the local topography and the drainage pattern
before the design and construction of any drainage system in any part
of Bayelsa.
Abstract: In this paper, we have proposed a low cost optimized solution for the movement of a three-arm manipulator using Genetic Algorithm (GA) and Analytical Hierarchy Process (AHP). A scheme is given for optimizing the movement of robotic arm with the help of Genetic Algorithm so that the minimum energy consumption criteria can be achieved. As compared to Direct Kinematics, Inverse Kinematics evolved two solutions out of which the best-fit solution is selected with the help of Genetic Algorithm and is kept in search space for future use. The Inverse Kinematics, Fitness Value evaluation and Binary Encoding like tasks are simulated and tested. Although, three factors viz. Movement, Friction and Least Settling Time (or Min. Vibration) are used for finding the Fitness Function / Fitness Values, however some more factors can also be considered.
Abstract: This paper introduces and studies new indexing techniques for content-based queries in images databases. Indexing is the key to providing sophisticated, accurate and fast searches for queries in image data. This research describes a new indexing approach, which depends on linear modeling of signals, using bases for modeling. A basis is a set of chosen images, and modeling an image is a least-squares approximation of the image as a linear combination of the basis images. The coefficients of the basis images are taken together to serve as index for that image. The paper describes the implementation of the indexing scheme, and presents the findings of our extensive evaluation that was conducted to optimize (1) the choice of the basis matrix (B), and (2) the size of the index A (N). Furthermore, we compare the performance of our indexing scheme with other schemes. Our results show that our scheme has significantly higher performance.
Abstract: This paper introduces an approach to construct a set of criteria for evaluating alternative options. Content analysis was used to collet criterion elements. Then the elements were classified and organized yielding to hierarchic structure. The reliability of the constructed criteria was evaluated in an experiment. Finally the criteria were used to evaluate alternative options indecision-making.
Abstract: Society has grown to rely on Internet services, and the
number of Internet users increases every day. As more and more
users become connected to the network, the window of opportunity
for malicious users to do their damage becomes very great and
lucrative. The objective of this paper is to incorporate different
techniques into classier system to detect and classify intrusion from
normal network packet. Among several techniques, Steady State
Genetic-based Machine Leaning Algorithm (SSGBML) will be used
to detect intrusions. Where Steady State Genetic Algorithm (SSGA),
Simple Genetic Algorithm (SGA), Modified Genetic Algorithm and
Zeroth Level Classifier system are investigated in this research.
SSGA is used as a discovery mechanism instead of SGA. SGA
replaces all old rules with new produced rule preventing old good
rules from participating in the next rule generation. Zeroth Level
Classifier System is used to play the role of detector by matching
incoming environment message with classifiers to determine whether
the current message is normal or intrusion and receiving feedback
from environment. Finally, in order to attain the best results,
Modified SSGA will enhance our discovery engine by using Fuzzy
Logic to optimize crossover and mutation probability. The
experiments and evaluations of the proposed method were performed
with the KDD 99 intrusion detection dataset.
Abstract: The increasing complexity of software development based on peer to peer networks makes necessary the creation of new frameworks in order to simplify the developer-s task. Additionally, some applications, e.g. fire detection or security alarms may require real-time constraints and the high level definition of these features eases the application development. In this paper, a service model based on a component model with real-time features is proposed. The high-level model will abstract developers from implementation tasks, such as discovery, communication, security or real-time requirements. The model is oriented to deploy services on small mobile devices, such as sensors, mobile phones and PDAs, where the computation is light-weight. Services can be composed among them by means of the port concept to form complex ad-hoc systems and their implementation is carried out using a component language called UM-RTCOM. In order to apply our proposals a fire detection application is described.
Abstract: In this paper a new method for increasing the speed of
SAGCM-APD is proposed. Utilizing carrier rate equations in
different regions of the structure, a circuit model for the structure is
obtained. In this research, in addition to frequency response, the
effect of added new charge layer on some transient parameters like
slew-rate, rising and falling times have been considered. Finally, by
trading-off among some physical parameters such as different layers
widths and droppings, a noticeable decrease in breakdown voltage
has been achieved. The results of simulation, illustrate some features
of proposed structure improvement in comparison with conventional
SAGCM-APD structures.
Abstract: In this paper we analyze the core issues affecting
software architecture in enterprise projects where a large number of
people at different backgrounds are involved and complex business,
management and technical problems exist. We first give general
features of typical enterprise projects and then present foundations of
software architectures. The detailed analysis of core issues affecting
software architecture in software development phases is given. We
focus on three main areas in each development phase: people,
process, and management related issues, structural (product) issues,
and technology related issues. After we point out core issues and
problems in these main areas, we give recommendations for
designing good architecture. We observed these core issues and the
importance of following the best software development practices and
also developed some novel practices in many big enterprise
commercial and military projects in about 10 years of experience.
Abstract: This is a survey research using quantitative and qualitative methodology. There were three objectives: 1) To study participatory level of community in water and waste environment management. 2) To study the affecting factors for community participation in water and waste environment management in Ampawa District, Samut Songkram Province. 3) To search for the participatory patterns in water and waste management. The population sample for the quantitative research was 1,364 people living in Ampawa District. The methodology was simple random sampling. Research instrument was a questionnaire and the qualitative research used purposive sampling in 6 Sub Districts which are Ta Ka, Suanluang, Bangkae, Muangmai, Kwae-om, and Bangnanglee Sub District Administration Organization. Total population is 63. For data analysis, the study used content analysis from quantitative research to synthesize and build question frame from the content for interview and conducting focus group interview. The study found that the community participatory in the issue of level in water and waste management are moderate of planning, operation, and evaluation. The issue of being beneficial is at low level. Therefore, the overall participatory level of community in water and waste environment management is at a medium level. The factors affecting the participatory of community in water and waste management are age, the period dwelling in the community and membership in which the mean difference is statistic significant at 0.05 in area of operation, being beneficial, and evaluation. For patterns of community participation, there is the correlation with water and waste management in 4 concerns which are 1) Participation in planning 2) Participation in operation 3) Participation in being beneficial both directly and indirectly benefited 4) Participation in evaluation and monitoring. The recommendation from this study is the need to create conscious awareness in order to increase participation level of people by organizing activities that promote participation with volunteer spirit. Government should open opportunities for people to participate in sharing ideas and create the culture of living together with equality which would build more concrete participation.
Abstract: Mobile IPv6 (MIPv6) describes how mobile node can change its point of attachment from one access router to another. As a demand for wireless mobile devices increases, many enhancements for macro-mobility (inter-domain) protocols have been proposed, designed and implemented in Mobile IPv6. Hierarchical Mobile IPv6 (HMIPv6) is one of them that is designed to reduce the amount of signaling required and to improve handover speed for mobile connections. This is achieved by introducing a new network entity called Mobility Anchor Point (MAP). This report presents a comparative study of the Hierarchical Mobility IPv6 and Mobile IPv6 protocols and we have narrowed down the scope to micro-mobility (intra-domain). The architecture and operation of each protocol is studied and they are evaluated based on the Quality of Service (QoS) parameter; handover latency. The simulation was carried out by using the Network Simulator-2. The outcome from this simulation has been discussed. From the results, it shows that, HMIPv6 performs best under intra-domain mobility compared to MIPv6. The MIPv6 suffers large handover latency. As enhancement we proposed to HMIPv6 to locate the MAP to be in the middle of the domain with respect to all Access Routers. That gives approximately same distance between MAP and Mobile Node (MN) regardless of the new location of MN, and possible shorter distance. This will reduce the delay since the distance is shorter. As a future work performance analysis is to be carried for the proposed HMIPv6 and compared to HMIPv6.