Abstract: Supersonic open and closed cavity flows are investigated experimentally and computationally. Free stream Mach number of two is set. Schlieren imaging is used to visualise the flow behaviour showing stark differences between open and closed. Computational Fluid Dynamics (CFD) is used to simulate open cavity of flow with aspect ratio of 4. A rear wall treatment is implemented in order to pursue a simple passive control approach. Good qualitative agreement is achieved between the experimental flow visualisation and the CFD in terms of the expansion-shock waves system. The cavity oscillations are shown to be dominated by the first and third Rossister modes combining to high fluctuations of non-linear nature above the cavity rear edge. A simple rear wall treatment in terms of a hole shows mixed effect on the flow oscillations, RMS contours, and time history density fluctuations are given and analysed.
Abstract: The Marangoni convective instability in a horizontal
fluid layer with the insoluble surfactant and nondeformable free
surface is investigated. The surface tension at the free surface is
linearly dependent on the temperature and concentration gradients.
At the bottom surface, the temperature conditions of uniform
temperature and uniform heat flux are considered. By linear stability
theory, the exact analytical solutions for the steady Marangoni
convection are derived and the marginal curves are plotted. The
effects of surfactant or elasticity number, Lewis number and Biot
number on the marginal Marangoni instability are assessed. The
surfactant concentration gradients and the heat transfer mechanism at
the free surface have stabilizing effects while the Lewis number
destabilizes fluid system. The fluid system with uniform temperature
condition at the bottom boundary is more stable than the fluid layer
that is subjected to uniform heat flux at the bottom boundary.
Abstract: In the present analysis an unsteady laminar
forced convection water boundary layer flow is considered.
The fluid properties such as viscosity and Prandtl number are
taken as variables such that those are inversely proportional to
temperature. By using quasi-linearization technique the nonlinear
coupled partial differential equations are linearized and
the numerical solutions are obtained by using implicit finite
difference scheme with the appropriate selection of step sizes.
Non-similar solutions have been obtained from the starting
point of the stream-wise coordinate to the point where skin
friction value vanishes. The effect non-uniform mass transfer
along the surface of the cylinder through slot is studied on the
skin friction and heat transfer coefficients.
Abstract: Smoke discharging is a main reason of air pollution
problem from industrial plants. The obstacle of a building has an
affect with the air pollutant discharge. In this research, a mathematical
model of the smoke dispersion from two sources and one source with
a structural obstacle is considered. The governing equation of the
model is an isothermal mass transfer model in a viscous fluid. The
finite element method is used to approximate the solutions of the
model. The triangular linear elements have been used for discretising
the domain, and time integration has been carried out by semi-implicit
finite difference method. The simulations of smoke dispersion in
cases of one chimney and two chimneys are presented. The maximum
calculated smoke concentration of both cases are compared. It is then
used to make the decision for smoke discharging and air pollutant
control problems on industrial area.
Abstract: Electromagnetic flowmeters with DC excitation are used for a wide range of fluid measurement tasks, but are rarely found in dosing applications with short measurement cycles due to the achievable accuracy. This paper will identify a number of factors that influence the accuracy of this sensor type when used for short-term measurements. Based on these results a new signal-processing algorithm will be described that overcomes the identified problems to some extend. This new method allows principally a higher accuracy of electromagnetic flowmeters with DC excitation than traditional methods.
Abstract: The purpose of this paper is applied Taguchi method on the optimization for PEMFC performance, and a representative Computational Fluid Dynamics (CFD) model is selectively performed for statistical analysis. The studied factors in this paper are pressure of fuel cell, operating temperature, the relative humidity of anode and cathode, porosity of gas diffusion electrode (GDE) and conductivity of GDE. The optimal combination for maximum power density is gained by using a three-level statistical method. The results confirmed that the robustness of the optimum design parameters influencing the performance of fuel cell are founded by pressure of fuel cell, 3atm; operating temperature, 353K; the relative humidity of anode, 50%; conductivity of GDE, 1000 S/m, but the relative humidity of cathode and porosity of GDE are pooled as error due to a small sum of squares. The present simulation results give designers the ideas ratify the effectiveness of the proposed robust design methodology for the performance of fuel cell.
Abstract: This paper investigates vortex shedding processes
occurring at the end of a stack of parallel plates, due to an oscillating
flow induced by an acoustic standing wave within an acoustic
resonator. Here, Particle Image Velocimetry (PIV) is used to quantify
the vortex shedding processes within an acoustic cycle
phase-by-phase, in particular during the “ejection" of the fluid out of
the stack. Standard hot-wire anemometry measurement is also applied
to detect the velocity fluctuations near the end of the stack.
Combination of these two measurement techniques allowed a detailed
analysis of the vortex shedding phenomena. The results obtained show
that, as the Reynolds number varies (by varying the plate thickness
and drive ratio), different flow patterns of vortex shedding are
observed by the PIV measurement. On the other hand, the
time-dependent hot-wire measurements allow obtaining detailed
frequency spectra of the velocity signal, used for calculating
characteristic Strouhal numbers. The impact of the plate thickness and
the Reynolds number on the vortex shedding pattern has been
discussed. Furthermore, a detailed map of the relationship between the
Strouhal number and Reynolds number has been obtained and
discussed.
Abstract: The purpose of the study was to determine the amount of Palm Kernel Oil (PKO) extracted from a packed bed of palm kernels in a supercritical fluid extractor using supercritical carbon dioxide (SC-CO2) as an environmental friendly solvent. Further, the study sought to ascertain the values of the overall mass transfer coefficient (K) of PKO evaluation through a mass transfer model, at constant temperature of 50 °C, 60 °C, and 70 °C and pressures range from 27.6 MPa, 34.5 MPa, 41.4 MPa and 48.3 MPa respectively. Finally, the study also seeks to demonstrate the application of the overall mass transfer coefficient values in relation to temperature and pressure. The overall mass transfer coefficient was found to be dependent pressure at each constant temperature of 50 °C, 60 °C and 70 °C. The overall mass transfer coefficient for PKO in a packed bed of palm kernels was found to be in the range of 1.21X 10-4 m min-1 to 1.72 X 10-4 m min-1 for a constant temperature of 50 °C and in the range of 2.02 X 10-4 m min-1 to 2.43 X 10-4 m min-1 for a constant temperature of 60 °C. Similar increasing trend of the overall mass transfer coefficient from 1.77 X 10-4 m min-1 to 3.64 X 10-4 m min-1 was also observed at constant temperature of 70 °C within the same pressure range from 27.6 MPa to 48.3 MPa.
Abstract: This paper examines the forced convection flow of
incompressible, electrically conducting viscous fluid past a sharp
wedge in the presence of heat generation or absorption with an
applied magnetic field. The system of partial differential equations
governing Falkner - Skan wedge flow and heat transfer is first
transformed into a system of ordinary differential equations using
similarity transformations which is later solved using an implicit
finite - difference scheme, along with quasilinearization technique.
Numerical computations are performed for air (Pr = 0.7) and
displayed graphically to illustrate the influence of pertinent physical
parameters on local skin friction and heat transfer coefficients and,
also on, velocity and temperature fields. It is observed that the
magnetic field increases both the coefficients of skin friction and heat
transfer. The effect of heat generation or absorption is found to be
very significant on heat transfer, but its effect on the skin friction is
negligible. Indeed, the occurrence of overshoot is noticed in the
temperature profiles during heat generation process, causing the
reversal in the direction of heat transfer.
Abstract: The main objective of this article is to present the semi-active vibration control using an electro-rheological fluid embedded sandwich structure for a cantilever beam. ER fluid is a smart material, which cause the suspended particles polarize and connect each other to form chain. The stiffness and damping coefficients of the ER fluid can be changed in 10 micro seconds; therefore, ERF is suitable to become the material embedded in the tunable vibration absorber to become a smart absorber. For the ERF smart material embedded structure, the fuzzy control law depends on the experimental expert database and the proposed self-tuning strategy. The electric field is controlled by a CRIO embedded system to implement the real application. This study investigates the different performances using the Type-1 fuzzy and interval Type-2 fuzzy controllers. The Interval type-2 fuzzy control is used to improve the modeling uncertainties for this ERF embedded shock absorber. The self-tuning vibration controllers using Type-1 and Interval Type-2 fuzzy law are implemented to the shock absorber system. Based on the resulting performance, Internal Type-2 fuzzy is better than the traditional Type-1 fuzzy control for this vibration control system.
Abstract: The simulation of external aerodynamics is one of the most challenging and important automotive CFD applications. With the rapid developments of digital computers, CFD is used as a practical tool in modern fluid dynamics research. It integrates fluid mechanics disciplines, mathematics and computer science. In this study, two different types of simulations were made, one for the flow around a simplified high speed passenger car with a rear-spoiler and the other for the flow without a rear-spoiler. The standard k-ε model is selected to numerically simulate the external flow field of the simplified Camry model with or without a rear-spoiler. Through an analysis of the simulation results, a new rear spoiler is designed and it shows a mild reduction of the vehicle aerodynamics drag. This leads to less vehicle fuel consumption on the road.
Abstract: Group contribution based models are widely used in
industrial applications for its convenience and flexibility. Although a
number of group contribution models have been proposed, there were
certain limitations inherent to those models. Models based on group
contribution excess Gibbs free energy are limited to low pressures and
models based on equation of state (EOS) cannot properly describe
highly nonideal mixtures including acids without introducing
additional modification such as chemical theory. In the present study
new a new approach derived from quantum chemistry have been used
to calculate necessary EOS group interaction parameters. The
COSMO-RS method, based on quantum mechanics, provides a
reliable tool for fluid phase thermodynamics. Benefits of the group
contribution EOS are the consistent extension to hydrogen-bonded
mixtures and the capability to predict polymer-solvent equilibria up to
high pressures. The authors are confident that with a sufficient
parameter matrix the performance of the lattice EOS can be improved
significantly.
Abstract: The B'enard-Marangoni thermal instability problem for
a viscoelastic Jeffreys- fluid layer with internal heat generation is
investigated. The fluid layer is bounded above by a realistic free
deformable surface and by a plane surface below. Our analysis
shows that while the internal heat generation and the relaxation time
both destabilize the fluid layer, its stability may be enhanced by an
increased retardation time.
Abstract: An experimental study is realized in order to verify the
Mini Heat Pipe (MHP) concept for cooling high power dissipation
electronic components and determines the potential advantages of
constructing mini channels as an integrated part of a flat heat pipe. A
Flat Mini Heat Pipe (FMHP) prototype including a capillary structure
composed of parallel rectangular microchannels is manufactured and
a filling apparatus is developed in order to charge the FMHP. The
heat transfer improvement obtained by comparing the heat pipe
thermal resistance to the heat conduction thermal resistance of a
copper plate having the same dimensions as the tested FMHP is
demonstrated for different heat input flux rates. Moreover, the heat
transfer in the evaporator and condenser sections are analyzed, and
heat transfer laws are proposed. In the theoretical part of this work, a
detailed mathematical model of a FMHP with axial microchannels is
developed in which the fluid flow is considered along with the heat
and mass transfer processes during evaporation and condensation.
The model is based on the equations for the mass, momentum and
energy conservation, which are written for the evaporator, adiabatic,
and condenser zones. The model, which permits to simulate several
shapes of microchannels, can predict the maximum heat transfer
capacity of FMHP, the optimal fluid mass, and the flow and thermal
parameters along the FMHP. The comparison between experimental
and model results shows the good ability of the numerical model to
predict the axial temperature distribution along the FMHP.
Abstract: Ionanofluids are a new and innovative class of heat transfer fluids which exhibit fascinating thermophysical properties compared to their base ionic liquids. This paper deals with the findings of thermal conductivity and specific heat capacity of ionanofluids as a function of a temperature and concentration of nanotubes. Simulation results using ionanofluids as coolants in heat exchanger are also used to access their feasibility and performance in heat transfer devices. Results on thermal conductivity and heat capacity of ionanofluids as well as the estimation of heat transfer areas for ionanofluids and ionic liquids in a model shell and tube heat exchanger reveal that ionanofluids possess superior thermal conductivity and heat capacity and require considerably less heat transfer areas as compared to those of their base ionic liquids. This novel class of fluids shows great potential for advanced heat transfer applications.
Abstract: In this study, the kinetic of biogas production was studied by performing a series laboratory experiment using rumen fluid of animal ruminant as inoculums. Cattle manure as substrate was inoculated by rumen fluid to the anaerobic biodigester. Laboratory experiments using 400 ml biodigester were performed in batch operation mode. Given 100 grams of fresh cattle manure was fed to each biodigester and mixed with rumen fluid by manure : rumen weight ratio of 1:1 (MR11). The operating temperatures were varied at room temperature and 38.5 oC. The cumulative volume of biogas produced was used to measure the biodigester performance. The research showed that the rumen fluid inoculated to biodigester gave significant effect to biogas production (P
Abstract: In this paper, the effects of radiation, chemical
reaction and double dispersion on mixed convection heat and mass
transfer along a semi vertical plate are considered. The plate is
embedded in a Newtonian fluid saturated non - Darcy (Forchheimer
flow model) porous medium. The Forchheimer extension and first
order chemical reaction are considered in the flow equations. The
governing sets of partial differential equations are nondimensionalized
and reduced to a set of ordinary differential
equations which are then solved numerically by Fourth order Runge–
Kutta method. Numerical results for the detail of the velocity,
temperature, and concentration profiles as well as heat transfer rates
(Nusselt number) and mass transfer rates (Sherwood number) against
various parameters are presented in graphs. The obtained results are
checked against previously published work for special cases of the
problem and are found to be in good agreement.
Abstract: The onset of Marangoni convection in a horizontal
fluid layer with internal heat generation overlying a solid layer
heated from below is studied. The upper free surface of a fluid is
nondeformable and the bottom boundary are rigid and no-slip. The
resulting eigenvalue problem is solved exactly. The critical values of
the Marangoni numbers for the onset of Marangoni convection are
calculated and the latter is found to be critically dependent on the
internal heating, depth ratio and conductivity ratio. The effects of the
thermal conductivity and the thickness of the solid plate on the onset
of convective instability with internal heating are studied in detail.
Abstract: A two dimensional numerical simulation has been
performed for incompressible and compressible fluid flow through
microchannels in slip flow regime. The Navier-Stokes equations have
been solved in conjunction with Maxwell slip conditions for
modeling flow field associated with slip flow regime. The wall
roughness is simulated with triangular microelements distributed on
wall surfaces to study the effects of roughness on fluid flow. Various
Mach and Knudsen numbers are used to investigate the effects of
rarefaction as well as compressibility. It is found that rarefaction has
more significant effect on flow field in microchannels with higher
relative roughness. It is also found that compressibility has more
significant effects on Poiseuille number when relative roughness
increases. In addition, similar to incompressible models the increase
in average fRe is more significant at low Knudsen number flows but
the increase of Poiseuille number duo to relative roughness is sharper
for compressible models. The numerical results have also validated
with some available theoretical and experimental relations and good
agreements have been seen.
Abstract: Two-interconnected fluidized bed systems are widely used in various processes such as Fisher-Tropsch, hot gas desulfurization, CO2 capture-regeneration with dry sorbent, chemical-looping combustion, sorption enhanced steam methane reforming, chemical-looping hydrogen generation system, and so on. However, most of two-interconnected fluidized beds systems require riser and/or pneumatic transport line for solid conveying and loopseals or seal-pots for gas sealing, recirculation of solids to the riser, and maintaining of pressure balance. The riser (transport bed) is operated at the high velocity fluidization condition and residence times of gas and solid in the riser are very short. If the reaction rate of catalyst or sorbent is slow, the riser can not ensure sufficient contact time between gas and solid and we have to use two bubbling beds for each reaction to ensure sufficient contact time. In this case, additional riser must be installed for solid circulation. Consequently, conventional two-interconnected fluidized bed systems are very complex, large, and difficult to operate. To solve these problems, a novel two-interconnected fluidized bed system has been developed. This system has two bubbling beds, solid injection nozzles, solid conveying lines, and downcomers. In this study, effects of operating variables on solid circulation rate, gas leakage between two beds have been investigated in a cold mode two-interconnected fluidized bed system. Moreover, long-term operation of continuous solid circulation up to 60 hours has been performed to check feasibility of stable operation.