Abstract: Thermal conductivity is an important characteristic of
a nanofluid in laminar flow heat transfer. This paper presents an
improved model for the prediction of the effective thermal
conductivity of nanofluids based on dimensionless groups. The
model expresses the thermal conductivity of a nanofluid as a function
of the thermal conductivity of the solid and liquid, their volume
fractions and particle size. The proposed model includes a parameter
which accounts for the interfacial shell, brownian motion, and
aggregation of particle. The validation of the model is verified by
applying the results obtained by the experiments of Tio2-water and
Al2o3-water nanofluids.
Abstract: Pressure wave velocity in a hydraulic system was
determined using piezo pressure sensors without removing fluid from
the system. The measurements were carried out in a low pressure
range (0.2 – 6 bar) and the results were compared with the results of
other studies. This method is not as accurate as measurement with
separate measurement equipment, but the fluid is in the actual
machine the whole time and the effect of air is taken into
consideration if air is present in the system. The amount of air is
estimated by calculations and comparisons between other studies.
This measurement equipment can also be installed in an existing
machine and it can be programmed so that it measures in real time.
Thus, it could be used e.g. to control dampers.
Abstract: In this paper, a simple microfluidic device for monitoring algal cell behavior is proposed. An array of algal microwells is fabricated by PDMS soft-lithography using X-ray LIGA mold, placed on a glass substrate. Two layers of replicated PDMS and substrate are attached by oxygen plasma bonding, creating a microchannel for the microfluidic system. Algal cell are loaded into the microfluidic device, which provides positive charge on the bottom surface of wells. Algal cells, which are negative charged, can be attracted to the bottom of the wells via electrostatic interaction. By varying the concentration of algal cells in the loading suspension, it is possible to obtain wells with a single cell. Liquid medium for cells monitoring are flown continuously over the wells, providing nutrient and waste exchange between the well and the main flow. This device could lead to the uncovering of the quantitative biology of the algae, which is a key to effective and extensive algal utilizations in the field of biotechnology, food industry and bioenergy research and developments.
Abstract: For many industrial applications plate heat
exchangers are demonstrating a large superiority over the
other types of heat exchangers. The efficiency of such a
device depends on numerous factors the effect of which needs
to be analysed and accurately evaluated.
In this paper we present a theoretical analysis of a cocurrent
plate heat exchanger and the results of its numerical
simulation.
Knowing the hot and the cold fluid streams inlet temperatures,
the respective heat capacities mCp
and the value of the
overall heat transfer coefficient, a 1-D mathematical model
based on the steady flow energy balance for a differential
length of the device is developed resulting in a set of N first
order differential equations with boundary conditions where N
is the number of channels.For specific heat exchanger
geometry and operational parameters, the problem is
numerically solved using the shooting method.
The simulation allows the prediction of the temperature
map in the heat exchanger and hence, the evaluation of its
performances. A parametric analysis is performed to evaluate
the influence of the R-parameter on the e-NTU values. For
practical purposes effectiveness-NTU graphs are elaborated
for specific heat exchanger geometry and different operating
conditions.
Abstract: Fluid flow in cylinders of elliptic cross-section was investigated. Fluid used is Liquefied petroleum gas (LPG). LPG found in Nigeria contains majorly butane with percentages of propane. Commercial available code FLUENT which uses finite volume method was used to solve fluid flow governing equations. There has been little attention paid to fluid flow in cylindrical elliptic pipes. The present work aims to predict the LPG gas flow in cylindrical pipes of elliptic cross-section. Results of flow parameters of velocity and pressure distributions are presented. Results show that the pressure drop in elliptic pipes is higher than circular pipe of the same cross-sectional area. This is an important result as the pressure drop is related to the pump power needed to drive the flow. Results show that the velocity increases towards centre of the pipe as the flow moves downstream, and also increases towards the outlet of the pipe.
Abstract: In the current work, a numerical parametric study was
performed in order to model the fluid mechanics in the riser of a
bubbling fluidized bed (BFB). The gas-solid flow was simulated by
mean of a multi-fluid Eulerian model incorporating the kinetic theory
for solid particles. The bubbling fluidized bed was simulated two
dimensionally by mean of a Computational Fluid Dynamic (CFD)
commercial software package, Fluent. The effects of using different
inter-phase drag function (the drag model of Gidaspow, Syamlal and
O-Brien and the EMMS drag model) on the model predictions were
evaluated and compared. The results showed that the drag models of
Gidaspow and Syamlal and O-Brien overestimated the drag force for
the FCC particles and predicted a greater bed expansion in
comparison to the EMMS drag model.
Abstract: Downward turbulent bubbly flows in pipes were
modeled using computational fluid dynamics tools. The
Hydrodynamics, phase distribution and turbulent structure of twophase
air-water flow in a 57.15 mm diameter and 3.06 m length
vertical pipe was modeled by using the 3-D Eulerian-Eulerian
multiphase flow approach. Void fraction, liquid velocity and
turbulent fluctuations profiles were calculated and compared against
experimental data. CFD results are in good agreement with
experimental data.
Abstract: Nowadays, fluidized bed plays an important part in industry. The design of this kind of reactor requires knowing the interfacial area between two phases and this interfacial area leads to calculate the solid holdup in the bed. Consequently achieving interfacial area between gas and solid in the bed experimentally is so significant. On interfacial area measurement in fluidized bed with gas has been worked, but light transmission technique has been used less. Therefore, in the current research the possibility of using of this technique and its accuracy are investigated. Measuring, a fluidized bed was designed and the problems were averted as far as possible. By using fine solid with equal shape and diameter and installing an optical system, the absorption of light during the time of fluidization has been measured. Results indicate that this method that its validity has been proved in the gas-liquid system, by different reasons have less application in gas-solid system. One important reason could be non-uniformity in such systems.
Abstract: Linear stability analysis of wake-shear layers in twophase
shallow flows is performed in the present paper. Twodimensional
shallow water equations are used in the analysis. It is
assumed that the fluid contains uniformly distributed solid particles.
No dynamic interaction between the carrier fluid and particles is
expected in the initial moment. The stability calculations are
performed for different values of the particle loading parameter and
two other parameters which characterize the velocity ratio and the
velocity deficit. The results show that the particle loading parameter
has a stabilizing effect on the flow while the increase in the velocity
ratio or in the velocity deficit destabilizes the flow.
Abstract: The stability characteristics of water lubricated journal bearings having three axial grooves are obtained theoretically. In this lubricant (water) is fed under pressure from one end of the bearing, through the 3-axial grooves (groove angles may vary). These bearings can use the process fluid as the lubricant, as in the case of feed water pumps. The Reynolds equation is solved numerically by the finite difference method satisfying the boundary conditions. The stiffness and damping coefficient for various bearing number and eccentricity ratios, assuming linear pressure drop along the groove, shows that smaller groove angles better results.
Abstract: In this article, a simulation method called the Homotopy Perturbation Method (HPM) is employed in the steady flow of a Walter's B' fluid in a vertical channel with porous wall. We employed Homotopy Perturbation Method to derive solution of a nonlinear form of equation obtained from exerting similarity transforming to the ordinary differential equation gained from continuity and momentum equations of this kind of flow. The results obtained from the Homotopy Perturbation Method are then compared with those from the Runge–Kutta method in order to verify the accuracy of the proposed method. The results show that the Homotopy Perturbation Method can achieve good results in predicting the solution of such problems. Ultimately we use this solution to obtain the other terms of velocities and physical discussion about it.
Abstract: Studies on gas solid mass transfer using Supercritical fluid CO2 (SC-CO2) in a packed bed of palm kernels was investigated at operating conditions of temperature 50 °C and 70 °C and pressures ranges from 27.6 MPa, 34.5 MPa, 41.4 MPa and 48.3 MPa. The development of mass transfer models requires knowledge of three properties: the diffusion coefficient of the solute, the viscosity and density of the Supercritical fluids (SCF). Matematical model with respect to the dimensionless number of Sherwood (Sh), Schmidt (Sc) and Reynolds (Re) was developed. It was found that the model developed was found to be in good agreement with the experimental data within the system studied.
Abstract: Bubble generation was observed using a high-speed
camera in subcooled flow boiling at low void fraction. Constant heat
flux was applied on one side of an upward rectangular channel to
make heated test channel. Water as a working fluid from high
subcooling to near saturation temperature was injected step by step to
investigate bubble behavior during void development. Experiments
were performed in two different pressures condition close to 2bar and
4bar. It was observed that in high subcooling when boiling was
commenced, bubble after nucleation departed its origin and slid
beside heated surface. In an observation window mean release
frequency of bubble fb,mean, nucleation site Ns and mean bubble
volume Vb,mean in each step of experiments were measured to
investigate wall vaporization rate. It was found that in proximity of
PNVG vaporization rate was increased significantly in compare with
condensation rate which remained in low value.
Abstract: To understand the seismic behavior of the offshore
structures, the dynamic interaction of the water-structure-soil should
be assessed. In this regard the role of the water dynamic properties in
magnifying or reducing of the effects of earthquake induced motions
on offshore structures haven't been investigated in precise manner in
available literature. In this paper the sea water level fluctuations
effects on the seismic behavior of a sample of offshore structures has
been investigated by emphasizing on the water-structure interaction
phenomenon. For this purpose a two dimensional finite element
model of offshore structures as well as surrounded water has been
developed using ANSYS software. The effect of soil interaction with
embedded pile foundation has been imposed by using a series of
nonlinear springs in horizontal and vertical directions in soil-piles
contact points. In the model, the earthquake induced motions have
been applied on springs and consequently the motions propagated
upward to the structure and surrounded water. As a result of
numerical study, the horizontal deformations of the offshore deck as
well as internal force and buckling coefficient in structural elements
have been recorded and controlled with and without water presence.
In part of study a parametric study has been accomplished on sea
water level fluctuations and effect of this parameter has been studied
on the aforementioned numerical results.
Abstract: The aim of this study was to evaluate the effect of preexercise glycerol hyperhydration on endurance performance in a heat chamber designed to simulate the World Championship Distance (WCD) duathlon (10km run, 40km ride, 5 km run). Duathlons are often performed in hot and humid conditions and as a result hydration is a major issue. Glycerol enhances the body’s capacity for fluid retention by inducing hyperhydration, which is theorized to improve thermoregulatory and cardiovascular responses, and thereby improve performance. Six well-trained athletes completed the testing protocol in a heat chamber at the La Trobe University Exercise Physiology Laboratory. Each testing session was approximately 4.5 hours in duration (2 hours of pre-exercise glycerol hyper-hydration followed by approximately 2.5 hours of exercise). The results showed an increased water retention pre-exercise and an improved overall performance of 2.04% was achieved by subjects ingesting the glycerol solution.
Abstract: The effect of a uniform magnetic field on the
formation of drops of specific size has been investigated numerically
in a T-shaped microchannel. Previous researches indicated that the
drop sizes of secondary stream decreases, with increasing main
stream flow rate and decreasing interfacial tension. In the present
study the effect of a uniform magnetic field on the main stream is
considered, and it is proposed that by increasing the Hartmann
number, the size of the drops of the secondary stream will be
decreased.
Abstract: This study experimentally investigates the heat transfer effects of forced convection and natural convection under different substrate openings design. A computational fluid dynamics (CFD) model was established and implemented to verify and explain the experimental results and heat transfer behavior. It is found that different opening position will destroy the growth of the boundary layer on substrates to alter the cooling ability for both forced under low Reynolds number and natural convection. Nevertheless, having too many opening may reduce heat conduction and affect the overall heat transfer performance. This study provides future researchers with a guideline on designing and electronic package manufacturing.
Abstract: Worldwide conventional resources of fossil fuel are depleting very fast due to large scale increase in use of transport vehicles every year, therefore consumption rate of oil in transport sector alone has gone very high. In view of this, the major thrust has now been laid upon the search of alternative energy source and also for cost effective energy conversion system. The air converted into compressed form by non conventional or conventional methods can be utilized as potential working fluid for producing shaft work in the air turbine and thus offering the capability of being a zero pollution energy source. This paper deals with the mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine. Effect of expansion action and steady flow work in the air turbine at high admission air pressure of 6 bar, for varying injection to vane angles ratios 0.2-1.6, at the interval of 0.2 and at different vane angles such as 30o, 45o, 51.4o, 60o, 72o, 90o, and 120o for 12, 8, 7, 6, 5, 4 and 3 vanes respectively at speed of rotation 2500 rpm, has been quantified and analyzed here. Study shows that the expansion power has major contribution to total power, whereas the contribution of flow work output has been found varying only up to 19.4%. It is also concluded that for variation of injection to vane angle ratios from 0.2 to 1.2, the optimal power output is seen at vane angle 90o (4 vanes) and for 1.4 to 1.6 ratios, the optimal total power is observed at vane angle 72o (5 vanes). Thus in the vaned type novel air turbine the optimum shaft power output is developed when rotor contains 4-5 vanes for almost all situations of injection to vane angle ratios from 0.2 to 1.6.
Abstract: This paper presents a computational study of the separated flow in a planer asymmetric diffuser. The steady RANS equations for turbulent incompressible fluid flow and six turbulence closures are used in the present study. The commercial software code, FLUENT 6.3.26, was used for solving the set of governing equations using various turbulence models. Five of the used turbulence models are available directly in the code while the v2-f turbulence model was implemented via User Defined Scalars (UDS) and User Defined Functions (UDF). A series of computational analysis is performed to assess the performance of turbulence models at different grid density. The results show that the standard k-ω, SST k-ω and v2-f models clearly performed better than other models when an adverse pressure gradient was present. The RSM model shows an acceptable agreement with the velocity and turbulent kinetic energy profiles but it failed to predict the location of separation and attachment points. The standard k-ε and the low-Re k- ε delivered very poor results.
Abstract: The present work is concerned with the free
convective two dimensional flow and heat transfer, in isotropic fluid
filled porous rectangular enclosure with differentially heated walls for
steady state incompressible flow have been investigated for non-
Darcy flow model. Effects of Darcy number (0.0001 £Da£ 10),
Rayleigh number (10 £Ra£ 5000), and aspect ratio (0.25 £AR£ 4), for
a range of porosity (0.4 £e£ 0.9) with and without moving lower wall
have been studied. The cavity was insulated at the lower and upper
surfaces. The right and left heated surfaces allows convective
transport through the porous medium, generating a thermal
stratification and flow circulations. It was found that the Darcy
number, Rayleigh number, aspect ratio, and porosity considerably
influenced characteristics of flow and heat transfer mechanisms. The
results obtained are discussed in terms of the Nusselt number,
vectors, contours, and isotherms.