Abstract: Reactive powder concretes (RPC) are characterized by
particle diameter not exceeding 600 μm and having very high
compressive and tensile strengths. This paper describes a new
generation of micro concrete, which has an initial, as well as a final,
high physicomechanical performance. To achieve this, we replaced
the Portland cement (15% by weight) by materials rich in Silica (Slag
and Dune Sand).
The results obtained from tests carried out on RPC show that
compressive and tensile strengths increase when adding the additions,
thus improving the compactness of mixtures via filler and pozzolanic
effect.
With a reduction of the aggregate phase in the RPC and the
abundance of dune sand (south Algeria) and slag (industrial byproduct
of blast furnace), the use of the RPC will allow Algeria to
fulfil economical as well as ecological requirements.
Abstract: The present paper deals with problems related to the
possibilities to use fractal systems to solve some important scientific
and practical problems connected with filtering and separation of
aqueous phases from organic ones. For this purpose a special
separator have been designed. The reactor was filled with a porous
material with fractal dimension, which is an integral part of the set
for filtration and separation of emulsions. As a model emulsion
hexadecan mixture with water in equal quantities (1:1) was used. We
examined the hydrodynamics of the separation of the emulsion at
different rates of submission of the entrance of the reactor.
Abstract: Synthetic aperture radar (SAR) imaging usually
requires echo data collected continuously pulse by pulse with certain
bandwidth. However in real situation, data collection or part of signal
spectrum can be interrupted due to various reasons, i.e. there will be
gaps in spatial spectrum. In this case we need to find ways to fill out
the resulted gaps and get image with defined resolution. In this paper
we introduce our work on how to apply iterative spatially variant
apodization (Super-SVA) technique to extrapolate the spatial
spectrum in both azimuthal and range directions so as to fill out the
gaps and get correct radar image.
Abstract: Unsteady natural convection and heat transfer in a square cavity partially filled with porous media using a thermal
non-equilibrium model is studied in this paper. The left vertical wall is
maintained at a constant hot temperature Th and the right vertical wall
is maintained at a constant cold temperature Tc, while the horizontal
walls are adiabatic. The governing equations are obtained by applying
the Darcy model and Boussinesq approximation. COMSOL’s finite
element method is used to solve the non-dimensional governing
equations together with specified boundary conditions. The governing
parameters of this study are the Rayleigh number (Ra = 10^5, and Ra = 10^6 ), Darcy namber (Da = 10^−2, and Da = 10^−3),
the modified thermal conductivity ratio (10^−1 ≤ γ ≤ 10^4), the inter-phase heat transfer coefficien (10^−1 ≤ H ≤ 10^3) and the
time dependent (0.001 ≤ τ ≤ 0.2). The results presented for
values of the governing parameters in terms of streamlines in both
fluid/porous-layer, isotherms of fluid in fluid/porous-layer, isotherms
of solid in porous layer, and average Nusselt number.
Abstract: It was determined that woody biomass and livestock excreta can be utilized as hydrogen resources and hydrogen produced from such sources can be used to fill fuel cell vehicles (FCVs) at hydrogen stations. It was shown that the biomass transport costs for hydrogen production may be reduced the costs for co-generation. In the Tokyo Metropolitan Area, there are only a few sites capable of producing hydrogen from woody biomass in amounts greater than 200 m3/h-the scale required for a hydrogen station to be operationally practical. However, in the case of livestock excreta, it was shown that 15% of the municipalities in this area are capable of securing sufficient biomass to be operationally practical for hydrogen production. The differences in feasibility of practical operation depend on the type of biomass.
Abstract: Waste management is now a global concern due to its
high environmental impact on climate change. Because of generating
huge amount of waste through our daily activities, managing waste in
an efficient way has become more important than ever. Alternative
Waste Technology (AWT), a new category of waste treatment
technology has been developed for energy recovery in recent years to
address this issue. AWT describes a technology that redirects waste
away from landfill, recovers more useable resources from the waste
flow and reduces the impact on the surroundings. Australia is one of
the largest producers of waste per-capita. A number of AWTs are
using in Australia to produce energy from waste. Presently, it is vital
to identify an appropriate AWT to establish a sustainable waste
management system in Australia. Identification of an appropriate
AWT through Multi-criteria analysis (MCA) of four AWTs by using
five key decision making criteria is presented and discussed in this
paper.
Abstract: The manufacturing transmission line tower parts has
being generated hazardous waste which is required proper disposal
of waste for protection of land pollution. Manufacturing Process in
the manufacturing of steel angle, plates, pipes, channels are passes
through conventional, semi automatic and CNC machines for
cutting, marking, punching, drilling, notching, bending operations.
All fabricated material Coated with thin layer of Zinc in Galvanizing
plant where molten zinc is used for coating. Prior to Galvanizing,
chemical like 33% concentrated HCl Acid, ammonium chloride and
d-oil being used for pretreatment of iron. The bath of water with
sodium dichromate is used for cooling and protection of the
galvanized steel. For the heating purpose the furnace oil burners are
used. These above process the Zinc dross, Zinc ash, ETP sludge and
waste pickled acid generated as hazardous waste. The RPG has
made captive secured land fill site, since 1997 since then it was
using for disposal of hazardous waste after completion of SLF
(Secured land fill) site. The RPG has raised height from ground
level then now it is being used for disposal of waste as he designed
the SLF after in creasing height of from GL it is functional without
leach ate or adverse impacts in the environment.
Abstract: The two significant overvoltages in power system,
switching overvoltage and lightning overvoltage, are investigated in
this paper. Firstly, the effect of various power system parameters on
Line Energization overvoltages is evaluated by simulation in ATP.
The dominant parameters include line parameters; short-circuit
impedance and circuit breaker parameters. Solutions to reduce
switching overvoltages are reviewed and controlled closing using
switchsync controllers is proposed as proper method.
This paper also investigates lightning overvoltages in the
overhead-cable transition. Simulations are performed in
PSCAD/EMTDC. Surge arresters are applied in both ends of cable to
fulfill the insulation coordination. The maximum amplitude of
overvoltages inside the cable is surveyed which should be of great
concerns in insulation coordination studies.
Abstract: Inconel718 has been widely used as a super alloy in aerospace application due to the high strength at elevated temperatures, satisfactory oxidation resistance and heat corrosion resistance. In this study, the Inconel718 has been fabricated using high technology of Metal Injection Molding (MIM) process due to the cost effective technique for producing small, complex and precision parts in high volume compared with conventional method through machining. Through MIM, the binder system is one of the most important criteria in order to successfully fabricate the Inconel718. Even though, the binder system is a temporary, but failure in the selection and removal of the binder system will affect on the final properties of the sintered parts. Therefore, the binder system based on palm oil derivative which is palm stearin has been formulated and developed to replace the conventional binder system. The rheological studies of the mixture between the powder and binders system have been determined properly in order to be successful during injection into injection molding machine. After molding, the binder holds the particles in place. The binder system has to be removed completely through debinding step. During debinding step, solvent debinding and thermal pyrolysis has been used to remove completely of the binder system. The debound part is then sintered to give the required physical and mechanical properties. The results show that the properties of the final sintered parts fulfill the Standard Metal Powder Industries Federation (MPIF) 35 for MIM parts.
Abstract: In the present study, development of salbutamol
sulphate nanoparticles that adhere to gastric mucus was investigated.
Salbutamol sulphate has low bioavailability due to short transit time in
gastric. It also has a positive surface charge that provides hurdles to be
encapsulated by the positively strong mucoadhesive polymer of
chitosan. To overcome the difficulties, the surface charge of active
ingredient was modified using several nonionic and anionic
stomach-specific polymers. The nanoparticles were prepared using
ionotropic gelation technique. The evaluation involved determination
of particle size, zeta potential, entrapment efficiency, in vitro drug
release and in vitro mucoadhesion test. Results exhibited that the use
of anionic alginate polymer was more satisfactory than that of
nonionic polymer. Characteristics of the particles was nano-size, high
encapsulation efficiency, fulfilled the drug release requirements and
adhesive towards stomach for around 11 hours. This result shows that
the salbutamol sulphate nanoparticles can be utilized for improvement
its delivery.
Abstract: The objectives of this study are to determine the
effects of soil cover type on characteristics of leachates generated
from landfill lysimeters. Four lysimeters with diameter and height
of 0.15 and 3.00 m, respectively, were prepared. Three lysimeters
were filled with municipal waste and three different cover soil types
i.e. sandy loam soil, silty loam soil and clay soil while another
lysimeter was filled solely with municipal waste. The study was
conducted in the rainy season. Leachate quantities were measured
every day and leachate characteristics were determined once a week.
The cumulative leachate quantity from the lysimeter filled solely
with municipal waste was found to be around 27% higher than the
lysimeters using cover soils. There were no any differences of the
cumulative leachate amounts generated from the lysimeters using
three types of soils. The comparison of the total mass of pollutants
generated from all lysimeters showed that the lysimeter filled solely
with municipal waste generated the maximum quantities of
pollutants. Among the lysimeters using different types of soils, the
lysimeter using sandy loam soil generated the lowest amount of most
of pollutants, compared with the lysimeters using silty loam and clay
soils. It can be concluded that in term of pollutant attenuation in the
leachate, a sandy loam is the most suitable soil to be used as a cover
soil in the landfill.
Abstract: Polymer melt compressibility and mold surface roughness, which are generally ignored during the filling stage of the conventional injection molding, may become increasingly significant in micro injection molding where the parts become smaller. By employing the 2.5D generalized Hele-Shaw model, we presented here the effects of polymer compressibility and mold surface roughness on mold-filling in a micro-thickness cavity. To elucidate the effects of surface roughness, numerical investigations were conducted using a cavity flat plate which has two halves with different surface roughness. This allows the comparison of flow field on two different halves under identical processing conditions but with different roughness. Results show that polymer compressibility and mold surface roughness have effects on mold filling in micro injection molding. There is in shrinkage reduction as the density is increased due to polymer melt compressibility during the filling stage.
Abstract: The practice of burying the solid waste under the ground is one of the waste disposal methods and dumping is known as an ultimate method in the fastest-growing cities like Rasht city in Iran. Some municipalities select the solid waste landfills without feasibility studies, programming, design and management plans. Therefore, several social and environmental impacts are created by these sites. In this study, the suitability of solid waste landfill in Rasht city, capital of Gilan Province is reviewed using Regional Screening Method (RSM), Geographic Information System (GIS) and Analytical Hierarchy Process (AHP). The results indicated that according to the suitability maps, the value of study site is midsuitable to suitable based on RSM and mid-suitable based on AHP.
Abstract: The application of agro-industrial waste in Aluminum
Metal Matrix Composites has been getting more attention as they
can reinforce particles in metal matrix which enhance the strength
properties of the composites. In addition, by applying these agroindustrial
wastes in useful way not only save the manufacturing cost
of products but also reduce the pollutions on environment. This
paper represents a literature review on a range of industrial wastes
and their utilization in metal matrix composites. The paper describes
the synthesis methods of agro-industrial waste filled metal matrix
composite materials and their mechanical, wear, corrosion, and
physical properties. It also highlights the current application and
future potential of agro-industrial waste reinforced composites in
aerospace, automotive and other construction industries.
Abstract: This paper highlights the importance of the selection
of the building-s wall material,and the shortcomings of the most
commonly used framed structures with masonry infills .The
objective of this study is investigating the behavior of infill walls as
structural components in existing structures.Structural infill walls are
very important in structural behavior under earthquake effects.
Structural capacity under the effect of earthquake,displacement and
relative story displacement are affected by the structural irregularities
.The presence of nonstructural masonry infill walls can modify
extensively the global seismic behavior of framed buildings .The
stability and integrity of reinforced concrete frames are enhanced by
masonry infill walls. Masonry infill walls alter displacement and
base shear of the frame as well. Short columns have great
importance during earthquakes,because their failure may lead to
additional structural failures and result in total building collapse.
Consequently the effects of short columns are considered in this
study.
Abstract: Perceptions of quality from both designers and users
perspective have now stretched beyond the traditional usability,
incorporating abstract and subjective concepts. This has led to a shift
in human computer interaction research communities- focus; a shift
that focuses on achieving user experience (UX) by not only fulfilling
conventional usability needs but also those that go beyond them. The
term UX, although widely spread and given significant importance,
lacks consensus in its unified definition. In this paper, we survey
various UX definitions and modeling frameworks and examine them
as the foundation for proposing a UX evolution lifecycle framework
for understanding UX in detail. In the proposed framework we identify
the building blocks of UX and discuss how UX evolves in various
phases. The framework can be used as a tool to understand experience
requirements and evaluate them, resulting in better UX design and
hence improved user satisfaction.
Abstract: The present work analyses different parameters of pressure die casting to minimize the casting defects. Pressure diecasting is usually applied for casting of aluminium alloys. Good surface finish with required tolerances and dimensional accuracy can be achieved by optimization of controllable process parameters such as solidification time, molten temperature, filling time, injection pressure and plunger velocity. Moreover, by selection of optimum process parameters the pressure die casting defects such as porosity, insufficient spread of molten material, flash etc. are also minimized. Therefore, a pressure die casting component, carburetor housing of aluminium alloy (Al2Si2O5) has been considered. The effects of selected process parameters on casting defects and subsequent setting of parameters with the levels have been accomplished by Taguchi-s parameter design approach. The experiments have been performed as per the combination of levels of different process parameters suggested by L18 orthogonal array. Analyses of variance have been performed for mean and signal-to-noise ratio to estimate the percent contribution of different process parameters. Confidence interval has also been estimated for 95% consistency level and three conformational experiments have been performed to validate the optimum level of different parameters. Overall 2.352% reduction in defects has been observed with the help of suggested optimum process parameters.
Abstract: Interior brick-infill partitions are usually considered as
non-structural components and only their weight is accounted for in
practical structural design. In this study, their effect on the progressive
collapse resistance of an RC building subjected to sudden column loss
is investigated. Three notional column loss conditions with four
different brick-infill locations are considered. Column-loss response
analyses of the RC building with and without brick infills are carried
out. Analysis results indicate that the collapse resistance is only
slightly influenced by the brick infills due to their brittle failure
characteristic. Even so, they may help to reduce the inelastic
displacement response under column loss. For practical engineering, it
is reasonably conservative to only consider the weight of brick-infill
partitions in the structural analysis.
Abstract: The flow field over a three dimensional pole barn
characterized by a cylindrical roof has been numerically investigated.
Wind pressure and viscous loads acting on the agricultural building
have been analyzed for several incoming wind directions, so as to
evaluate the most critical load condition on the structure. A constant
wind velocity profile, based on the maximum reference wind speed in
the building site (peak gust speed worked out for 50 years return
period) and on the local roughness coefficient, has been simulated.
In order to contemplate also the hazard due to potential air
wedging between the stored hay and the lower part of the ceiling, the
effect of a partial filling of the barn has been investigated.
The distribution of wind-induced loads on the structure have been
determined, allowing a numerical quantification of the effect of wind
direction on the induced stresses acting on a hemicylindrical roof.
Abstract: This paper reports the results of an experimental work
conducted to investigate the effect of curing conditions on the
compressive strength of self-compacting geopolymer concrete
prepared by using fly ash as base material and combination of sodium
hydroxide and sodium silicate as alkaline activator. The experiments
were conducted by varying the curing time and curing temperature in
the range of 24-96 hours and 60-90°C respectively. The essential
workability properties of freshly prepared Self-compacting
Geopolymer concrete such as filling ability, passing ability and
segregation resistance were evaluated by using Slump flow,
V-funnel, L-box and J-ring test methods. The fundamental
requirements of high flowability and resistance to segregation as
specified by guidelines on Self-compacting Concrete by EFNARC
were satisfied. Test results indicate that longer curing time and curing
the concrete specimens at higher temperatures result in higher
compressive strength. There was increase in compressive strength
with the increase in curing time; however increase in compressive
strength after 48 hours was not significant. Concrete specimens cured
at 70°C produced the highest compressive strength as compared to
specimens cured at 60°C, 80°C and 90°C.