Abstract: Binder drainage test is widely used to set an upper
limit to the design binder content of porous asphalt. However, the
presence of high amount of fine particles in the drained binder may
affect the accuracy of the test result. This paper presents a study to
characterize the composition and particle size distribution of fine
particles accumulated in the drained binder. Fine aggregates and filler
in the drained binder were extracted using a suitable solvent. Then,
wet and dry sieve analysis was carried out to identify the actual
composition of the extracted fine aggregates and filler. From the
results, almost half of the drained binder consisted of fine aggregates
and this significantly affects the accuracy of the design binder content
of porous asphalt mix. This simple finding highlights the importance
of taking into account the presence of fine aggregates in the
calculation of drained binder.
Abstract: A comprehensive discussion of feasible strategies for sustainable energy supply is urgently needed to achieve a turnaround of the current energy situation. The necessary fundamentals required for the development of a long term energy vision are lacking to a great extent due to the absence of reasonable long term scenarios that fulfill the requirements of climate protection and sustainable energy use. The contribution of the study is based on a search for sustainable energy paths in the long run for Austria. The analysis makes use of secondary data predominantly. The measures developed to avoid CO2 emissions and other ecological risk factors vary to a great extent among all economic sectors. This is shown by the calculation of CO2 cost of abatement curves. In this study it is demonstrated that the most effective technical measures with the lowest CO2 abatement costs yield solutions to the current energy problems. Various scenarios are presented concerning the question how the technological and environmental options for a sustainable energy system for Austria could look like in the long run. It is shown how sustainable energy can be supplied even with today-s technological knowledge and options available. The scenarios developed include an evaluation of the economic costs and ecological impacts. The results are not only applicable to Austria but demonstrate feasible and cost efficient ways towards a sustainable future.
Abstract: Optimization of rational geometrical and mechanical
parameters of panel with curved plywood ribs is considered in this
paper. The panel consists of cylindrical plywood ribs manufactured
from Finish plywood, upper and bottom plywood flange, stiffness
diaphragms. Panel is filled with foam. Minimal ratio of structure self
weight and load that could be applied to structure is considered as
rationality criteria. Optimization is done, by using classical beam
theory without nonlinearities. Optimization of discreet design
variables is done by Genetic algorithm.
Abstract: The effects of seawater and slurry ice bleeding methods on the sensory, microbiological and chemical quality changes of cod fillets during chilled storage were examined in this study. The results from sensory evaluation showed that slurry ice bleeding method prolonged the shelf life of cod fillets up to 13-14 days compared to 10-11 days for fish bled in seawater. Slurry ice bleeding method also led to a slower microbial growth and biochemical developments, resulting lower total plate count (TPC), H2S-producing bacteria count, total volatile basic nitrogen (TVB-N), trimethylamine (TMA), free fatty acid (FFA) content and higher phospholipid content (PL) compared to those of samples bled in seawater. The results of principle component analysis revealed that TPC, H2S-producing bacteria, TVB-N, TMA and FFA were in significant correlation. They were also in negative correlation with sensory evaluation (Torry score), PL and water holding capacity (WHC).
Abstract: This study evaluates the performance of horizontal
subsurface flow constructed wetland (HSSF-CW) for the removal of
chlorinated resin and fatty acids (RFAs) from pulp and paper mill
wastewater. The dimensions of the treatment system were 3.5 m x 1.5
m x 0.28 m with surface area of 5.25 m2, filled with fine sand and
gravel. The cell was planted with an ornamental plant species Canna
indica. The removal efficiency of chlorinated RFAs was in the range
of 92-96% at the hydraulic retention time (HRT) of 5.9 days. Plant
biomass and soil (sand and gravel) were analyzed for chlorinated
RFAs content. No chlorinated RFAs were detected in plant biomass
but detected in soil samples. Mass balance studies of chlorinated
RFAs in HSSF-CW were also carried out.
Abstract: To provide a better understanding of fair share policies supported by current production schedulers and their impact on scheduling performance, A relative fair share policy supported in four well-known production job schedulers is evaluated in this study. The experimental results show that fair share indeed reduces heavy-demand users from dominating the system resources. However, the detailed per-user performance analysis show that some types of users may suffer unfairness under fair share, possibly due to priority mechanisms used by the current production schedulers. These users typically are not heavy-demands users but they have mixture of jobs that do not spread out.
Abstract: Municipal solid waste (MSW) comprises of a wide
range of heterogeneous materials generated by individual, household
or organization and may include food waste, garden wastes, papers,
textiles, rubbers, plastics, glass, ceramics, metals, wood wastes,
construction wastes but it is not limited to the above mentioned
fractions. The most common Municipal Solid Waste pretreatment
method in use is thermal pretreatment (incineration) and Mechanical
Biological pretreatment. This paper presents an overview of these
two pretreatment methods describing their benefits and laboratory
scale reactors that simulate landfill conditions were constructed in
order to compare emissions in terms of biogas production and
leachate contamination between untreated Municipal Solid Waste and
Mechanical Biological Pretreated waste. The findings of this study
showed that Mechanical Biological pretreatment of waste reduces the
emission level of waste and the benefit over the landfilling of
untreated waste is significant.
Abstract: This study aimed to explore future life orientation and
support that needed to accomplish it. A total of 258 participants are
Javanese high school student. The age of the sample ranges from 14
to 18 years old. Participants were asked about their future aspiration,
their reason of choosing them as important goals in their life, and
support that they need to accomplished their goals using open ended
questionnaire. The responses were categorized through content
analysis into four main categories. They are: (1) Self Fulfillment
(72.1%) (2) Parents and Family (16.7%) (3) Altruism (8.1%) (4)
Social and Economy Status (3.1%). Meanwhile, the categories for
support that they needed are shown as follows: (1) Affection Support
(64.7%) (2) Spiritual support (17.4%) (3) Material Support (10.9%)
(4) Guidance Support (7.0%). The research found that affection
support always gets the highest number in every future orientation
categories. It can be concluded that although Javanese adolescents
have different future orientation, they basically need affection
support.
Abstract: Availability of raw materials is important for
Indonesia as a furniture exporting country. Teak log as raw materials
is supplied to the furniture industry by Perum Perhutani (PP). PP
needs to involve carbon trading for nature conservation. PP also has
an obligation in the Corporate Social Responsibility program. PP and
furniture industry also must prosecute the regulations related to
ecological issues and labor rights. This study has the objective to
create the relationship model between supplier and manufacturer to
fulfill teak log demand that involving teak forest carbon
sequestration. A model is formulated as Goal Programming to get the
favorable solution for teak log procurement and support carbon
sequestration that considering economical, ecological, and social
aspects of both supplier and manufacturer. The results show that the
proposed model can be used to determine the teak log quantity
involving carbon trading to achieve the seven goals to be satisfied the
sustainability considerations.
Abstract: This research studied recycled waste by the Recyclable Material Bank Project of 4 universities in the central region of Thailand for the evaluation of reducing greenhouse gas emissions compared with landfilling activity during July 2012 to June 2013. The results showed that the projects collected total amount of recyclable wastes of about 911,984.80 kilograms. Office paper had the largest amount among these recycled wastes (50.68% of total recycled waste). Groups of recycled waste can be prioritized from high to low according to their amount as paper, plastic, glass, mixed recyclables, and metal, respectively. The project reduced greenhouse gas emissions equivalent to about 2814.969 metric tons of carbon dioxide. The most significant recycled waste that affects the reduction of greenhouse gas emissions is office paper which is 70.16% of total reduced greenhouse gasses emission. According to amount of reduced greenhouse gasses emission, groups of recycled waste can be prioritized from high to low significances as paper, plastic, metals, mixed recyclables, and glass, respectively.
Abstract: FlexRay, as a communication protocol for automotive
control systems, is developed to fulfill the increasing demand on the
electronic control units for implementing systems with higher safety
and more comfort. In this work, we study the impact of
radiation-induced soft errors on FlexRay-based steer-by-wire system.
We injected the soft errors into general purpose register set of FlexRay
nodes to identify the most critical registers, the failure modes of the
steer-by-wire system, and measure the probability distribution of
failure modes when an error occurs in the register file.
Abstract: A novel physico-chemical route to produce few layer graphene nanoribbons with atomically smooth edges is reported, via acid treatment (H2SO4:HNO3) followed by characteristic thermal shock processes involving extremely cold substances. Samples were studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy and X-ray photoelectron spectroscopy. This method demonstrates the importance of having the nanotubes open ended for an efficient uniform unzipping along the nanotube axis. The average dimensions of these nanoribbons are approximately ca. 210 nm wide and consist of few layers, as observed by transmission electron microscopy. The produced nanoribbons exhibit different chiralities, as observed by high resolution transmission electron microscopy. This method is able to provide graphene nanoribbons with atomically smooth edges which could be used in various applications including sensors, gas adsorption materials, composite fillers, among others.
Abstract: Studying literature theme in the fields of tourism and
sustainable development and its importance in today world and their
criteria in architecture, here in this article we will also study the area
where the selected site is located; beside the Aab-Ask Village located
in Larijan region in Mazandaran province on the way to Haraz – one
of the tourism routes of Iran. After these studies by analyzing the
site, its strong potentials – such as mineral water springs (hot
springs), geothermal, landscapes and ideal climate - as a tourist
attraction spot in the region, and considering sustainable
development criteria – with regard to limits and available facilities –
a plan was offered that could change the region to provide the needs
of local people and in addition change it to a place where tourism
services is offered to the visitors and make it an acceptable sample of
stable building in Iran. Finally the reason to make design for this
complex is recovery of natural and historical values of Aab-Ask area
regarding development and sustainable architecture criteria in the
form of a functional sample which can be a suitable place to fulfill
this goal for having lots of strong points in attracting cultural and
sustainable tourist.
Abstract: Due to the low heavy metal concentrations, the
bottom ash from a 32 MW municipal district heating plant was
determined to be a potential forest fertilizer as such. However,
additional Ca would be needed, because its Ca concentration of 1.9-
% (d.w.) was lower than the statutory Finnish minimum limit value
of 6.0-% (d.w.) for Ca in forest fertilizer. Due to the elevated As
concentration (53.0 mg/kg; d.w.) in the fly ash from the 32 MW
municipal district heating plant, and Cr concentration (620 mg/kg;
d.w.) in the ash fraction (i.e. mixture of the bottom ash and fly ash)
from the 6 MW municipal district heating plant, which exceed the
limit values of 30 mg/kg (d.w.) and 300 mg/kg (d.w.) for As and Cr,
respectively, these residues are not suitable as forest fertilizers.
Although these ash fractions cannot be used as a forest fertilizer as
such, they can be used for the landscaping of landfills or in industrial
and other areas that are closed to the public. However, an
environmental permit is then needed.
Abstract: A virtualized and virtual approach is presented on
academically preparing students to successfully engage at a strategic
perspective to understand those concerns and measures that are both
structured and not structured in the area of cyber security and
information assurance. The Master of Science in Cyber Security and
Information Assurance (MSCSIA) is a professional degree for those
who endeavor through technical and managerial measures to ensure
the security, confidentiality, integrity, authenticity, control,
availability and utility of the world-s computing and information
systems infrastructure. The National University Cyber Security and
Information Assurance program is offered as a Master-s degree. The
emphasis of the MSCSIA program uniquely includes hands-on
academic instruction using virtual computers. This past year, 2011,
the NU facility has become fully operational using system
architecture to provide a Virtual Education Laboratory (VEL)
accessible to both onsite and online students. The first student cohort
completed their MSCSIA training this past March 2, 2012 after
fulfilling 12 courses, for a total of 54 units of college credits. The
rapid pace scheduling of one course per month is immensely
challenging, perpetually changing, and virtually multifaceted. This
paper analyses these descriptive terms in consideration of those
globalization penetration breaches as present in today-s world of
cyber security. In addition, we present current NU practices to
mitigate risks.
Abstract: In this study, the reduction of Cr(VI) by use of scrap
iron, a cheap and locally available industrial waste, was investigated
in continuous system. The greater scrap iron efficiency observed for
the first two sections of the column filling indicate that most of the
reduction process was carried out in the bottom half of the column
filling. This was ascribed to a constant decrease of Cr(VI)
concentration inside the filling, as the water front passes from the
bottom to the top end of the column. While the bottom section of the
column filling was heavily passivated with secondary mineral phases,
the top section was less affected by the passivation process; therefore
the column filling would likely ensure the reduction of Cr(VI) for
time periods longer than 216 hours. The experimental results indicate
that fixed beds columns packed with scrap iron could be successfully
used for the first step of Cr(VI) polluted wastewater treatment.
However, the mass of scrap iron filling should be carefully estimated
since it significantly affects the Cr(VI) reduction efficiency.
Abstract: With the increasing spread of computers and the internet among culturally, linguistically and geographically diverse communities, issues of internationalization and localization and becoming increasingly important. For some of the issues such as different scales for length and temperature, there is a well-developed measurement theory. For others such as date formats no such theory will be possible. This paper fills a gap by developing a measurement theory for a class of scales previously overlooked, based on discrete and interval-valued scales such as spanner and shoe sizes. The paper gives a theoretical foundation for a class of data representation problems.
Abstract: Buildings with floating column are highly undesirable built in seismically active areas. Many urban multi-storey buildings today have floating column buildings which are adopted to accommodate parking at ground floor or reception lobbies in the first storey. The earthquake forces developed at different floor levels in a building need to be brought down along the height to the ground by the shortest path; any deviation or discontinuity in this load transfer path results in poor performance of the building. Floating column buildings are severely damaged during earthquake. Damage on this structure can be reduce by taking the effect of infill wall. This paper presents the effect of stiffness of infill wall to the damage occurred in floating column building when ground shakes. Modelling and analysis are carried out by non linear analysis programme IDARC-2D. Damage occurred in beams, columns, storey are studied by formulating modified Park & Ang model to evaluate damage indices. Overall structural damage indices in buildings due to shaking of ground are also obtained. Dynamic response parameters i.e. lateral floor displacement, storey drift, time period, base shear of buildings are obtained and results are compared with the ordinary moment resisting frame buildings. Formation of cracks, yield, plastic hinge, are also observed during analysis.
Abstract: The purpose of this study is to investigate the capacity
of natural Turkish zeolite for NH4-N removal from landfill leachate.
The effects of modification and initial concentration on the removal
of NH4-N from leachate were also investigated. The kinetics of
adsorption of NH4-N has been discussed using three kinetic models,
i.e., the pseudo-second order model, the Elovich equation, the
intraparticle diffuion model. Kinetic parameters and correlation
coefficients were determined. Equilibrium isotherms for the
adsorption of NH4-N were analyzed by Langmuir, Freundlich and
Tempkin isotherm models. Langmuir isotherm model was found to
best represent the data for NH4-N.
Abstract: Until recently it would have been unusual to consider classifying population movements and refugees as security problem. However, efforts at shaping our world to make ourselves secure have paradoxically led to ever greater insecurity. The feeling of uncertainty, pertinent throughout all discourses of security, has led to the creation of security production into seemingly benign routines of everyday life. Yet, the paper argues, neither of security discourses accounted for, disclosed and challenged the fundamental aporias embedded in Western security narratives. In turn, the paper aims to unpick the conventional security wisdom, which is haunted with strong ontologies, embedded in the politics of Orientalism, and (in)security nexus. The paper concludes that current security affair conceals the integral impossibility of fulfilling its very own promise of assured security. The paper also provides suggestions about alternative security discourse based on mutual dialogue.