Abstract: Polymeric composites are being increasingly used as
repair material for repairing critical infrastructures such as building,
bridge, pressure vessel, piping and pipeline. Technique in repairing
damaged pipes is one of the major concerns of pipeline owners.
Considerable researches have been carried out on the repair of
corroded pipes using composite materials. This article attempts a
short review of the subject matter to provide insight into various
techniques used in repairing corroded pipes, focusing on a wide range
of composite repair systems. These systems including pre-cured
layered, flexible wet lay-up, pre-impregnated, split composite sleeve
and flexible tape systems. Both advantages and limitations of these
repair systems were highlighted. Critical technical aspects have been
discussed through the current standards and practices. Research gaps
and future study scopes in achieving more effective design
philosophy are also presented.
Abstract: Fresh concrete has one of dynamic properties known
as slump. Slump of concrete is design to compatible with placing
method. Due to hydration reaction of cement, the slump of concrete
is loss through time. Therefore, delayed concrete probably get reject
because slump is unacceptable. In order to recover the slump of
delayed concrete the second dose of superplasticizer (naphthalene
based type F) is added into the system, the slump recovery can be
done as long as the concrete is not setting. By adding superplasticizer
as solution for recover unusable slump loss concrete may affects
other concrete properties. Therefore, this paper was observed setting
times and compressive strength of concrete after being re-dose with
chemical admixture type F (superplasticizer, naphthalene based) for
slump recovery. The concrete used in this study was fly ash concrete
with fly ash replacement of 0%, 30% and 50% respectively. Concrete
mix designed for test specimen was prepared with paste content (ratio
of volume of cement to volume of void in the aggregate) of 1.2 and
1.3, water-to-binder ratio (w/b) range of 0.3 to 0.58, initial dose of
superplasticizer (SP) range from 0.5 to 1.6%. The setting times of
concrete were tested both before and after re-dosed with different
amount of second dose and time of dosing. The research was
concluded that addition of second dose of superplasticizer would
increase both initial and final setting times accordingly to dosage of
addition. As for fly ash concrete, the prolongation effect was higher
as the replacement of fly ash increase. The prolongation effect can
reach up to maximum about 4 hours. In case of compressive strength,
the re-dosed concrete has strength fluctuation within acceptable range
of ±10%.
Abstract: Bezier curves have useful properties for path
generation problem, for instance, it can generate the reference
trajectory for vehicles to satisfy the path constraints. Both algorithms
join cubic Bezier curve segment smoothly to generate the path. Some
of the useful properties of Bezier are curvature. In mathematics,
curvature is the amount by which a geometric object deviates from
being flat, or straight in the case of a line. Another extrinsic example
of curvature is a circle, where the curvature is equal to the reciprocal
of its radius at any point on the circle. The smaller the radius, the
higher the curvature thus the vehicle needs to bend sharply. In this
study, we use Bezier curve to fit highway-like curve. We use
different approach to find the best approximation for the curve so that
it will resembles highway-like curve. We compute curvature value by
analytical differentiation of the Bezier Curve. We will then compute
the maximum speed for driving using the curvature information
obtained. Our research works on some assumptions; first, the Bezier
curve estimates the real shape of the curve which can be verified
visually. Even though, fitting process of Bezier curve does not
interpolate exactly on the curve of interest, we believe that the
estimation of speed are acceptable. We verified our result with the
manual calculation of the curvature from the map.
Abstract: Lead being a toxic heavy metal that mankind is
exposed to the highest levels of this metal. There are different sources
of environmental pollution with lead as lead alkyl additives in petrol
and manufacturing processes. The contaminated atmosphere in urban
and industrial areas by lead in Egypt may lead to the contamination
of foods beside the other different sources. The present investigation
studied the risk assessment of lead in some Egyptian edible
vegetables and fruits collected from different environments in Greater
Cairo Governorate, i.e. industrial, heavy traffic and rural areas. A
total of 325 leafy and fruity vegetables and fruits samples belonging
to 11, 6 and 4 different species, respectively were randomly collected
from markets of the three main models. Data indicated the variation
of lead levels in different three areas. The highest levels of lead were
detected in the samples collected from industrial and traffic areas.
However, the lowest levels were found in the rural areas. It could be
concluded that determination of lead levels in foods from different
localities and environments at regularly is very important.
Abstract: Rivers have transient storage or dead zones where
injected pollutants or solutes are entrapped for considerable period of
time, known as residence time, before being released into the main
flowing zones of rivers. In this study, a new empirical expression for
residence time, implementing genetic programming on published
dispersion data, has been derived. The proposed expression uses few
hydraulic and geometric characteristics of rivers which are normally
known to the authorities. When compared with some reported
expressions, based on various statistical indices, it can be concluded
that the proposed expression predicts the residence time of pollutants
in natural rivers more accurately.
Abstract: Large quantities of solid wastes being generated
worldwide from sources such as household, domestic, industrial,
commercial and construction demolition activities, leads to
environmental concerns. Utilization of these wastes in making
building construction materials can reduce the magnitude of the
associated problems. When these waste products are used in place of
other conventional materials, natural resources and energy are
preserved and expensive and/or potentially harmful waste disposal is
avoided. Recycling which is regarded as the third most preferred waste
disposal option, with its numerous environmental benefits, stand as a
viable option to offset the environmental impact associated with the
construction industry. This paper reviews the results of laboratory tests and important
research findings, and the potential of using these wastes in building
construction materials with focus on sustainable development.
Research gaps, which includes; the need to develop standard mix
design for solid waste based building materials; the need to develop
energy efficient method of processing solid waste use in concrete; the
need to study the actual behavior or performance of such building
materials in practical application and the limited real life application
of such building materials have also been identified. A research is being proposed to develop an environmentally
friendly, lightweight building block from recycled waste paper,
without the use of cement, and with properties suitable for use as
walling unit. This proposed research intends to incorporate,
laboratory experimentation and modeling to address the identified
research gaps.
Abstract: Laura Island, which is located about 50 km away from
downtown, is a source of water supply in Majuro atoll, which is the
capital of the Republic of the Marshall Islands. Low and flat Majuro
atoll has neither river nor lake. It is very important for Majuro atoll to
ensure the conservation of its water resources. However, upconing,
which is the process of partial rising of the freshwater-saltwater
boundary near the water-supply well, was caused by the excess
pumping from it during the severe drought in 1998. Upconing will
make the water usage of the freshwater lens difficult. Thus,
appropriate water usage is required to prevent up coning in the
freshwater lens because there is no other water source during drought. Numerical simulation of water usage applying SEAWAT model
was conducted at the central part of Laura Island, including the water
supply well, which was affected by upconing. The freshwater lens was
created as a result of infiltration of consistent average rainfall. The lens
shape was almost the same as the one in 1985. 0 of monthly rainfall
and variable daily pump discharge were used to calculate the
sustainable pump discharge from the water supply well. Consequently,
the total amount of pump discharge was increased as the daily pump
discharge was increased, indicating that it needs more time to recover
from upconing. Thus, a pump standard to reduce the pump intensity is
being proposed, which is based on numerical simulation concerning
the occurrence of the up-coning phenomenon in Laura Island during
the drought.
Abstract: The use of Computer Aided Design (CAD)
technologies has become pervasive in the Architecture, Engineering
and Construction (AEC) industry. This has led to its inclusion as an
important part of the training module in the curriculum for
Architecture Schools in Nigeria. This paper examines the ethical
questions that arise in the implementation of Computer Aided Design
(CAD) Content of the curriculum for Architectural education. Using
existing literature, it begins this scrutiny from the propriety of
inclusion of CAD into the education of the architect and the
obligations of the different stakeholders in the implementation
process. It also examines the questions raised by the negative use of
computing technologies as well as perceived negative influence of
the use of CAD on design creativity. Survey methodology was
employed to gather data from the Department of Architecture,
Chukwuemeka Odumegwu Ojukwu University Uli, which has been
used as a case study on how the issues raised are being addressed.
The paper draws conclusions on what will make for successful ethical
implementation.
Abstract: Production fluids are transported from the platform to
tankers or process facilities through transfer pipelines. Water being
one of the heavier phases tends to settle at the bottom of pipelines
especially at low flow velocities and this has adverse consequences
for pipeline integrity. On restart after a shutdown, this could result in
corrosion and issues for process equipment, thus the need to have the
heavier liquid dispersed into the flowing lighter fluid. This study
looked at the flow regime of low water cut and low flow velocity oil
and water flow using conductive film thickness probes in a large
diameter 4-inch pipe to obtain oil and water interface height and the
interface structural velocity. A wide range of 0.1–1.0 m/s oil and
water mixture velocities was investigated for 0.5–5% water cut. Two
fluid model predictions were used to compare with the experimental
results.
Abstract: In this study, the time-dependent behavior of damaged
reinforced concrete shear wall structures strengthened with composite
plates having variable fibers spacing was investigated to analyze their
seismic response. In the analytical formulation, the adherent and the
adhesive layers are all modeled as shear walls, using the mixed Finite
Element Method (FEM). The anisotropic damage model is adopted to
describe the damage extent of the Reinforced Concrete shear walls.
The phenomenon of creep and shrinkage of concrete has been
determined by Eurocode 2. Large earthquakes recorded in Algeria
(El-Asnam and Boumerdes) have been tested to demonstrate the
accuracy of the proposed method. Numerical results are obtained for non-uniform distributions of
carbon fibers in epoxy matrices. The effects of damage extent and the
delay mechanism creep and shrinkage of concrete are highlighted.
Prospects are being studied.
Abstract: The present research aimed at studying the awareness
and attitudes of teachers towards inclusive education. The sample
consisted of 60 teachers, teaching in the primary section (1st – 4th) of
regular schools affiliated to the SSC board in Mumbai. Sample was
selected by Multi-stage cluster sampling technique. A semi-structured
self-constructed interview schedule and a self-constructed attitude
scale was used to study the awareness of teachers about disability and
Inclusive education, and their attitudes towards inclusive education
respectively. Themes were extracted from the interview data and
quantitative data was analyzed using SPSS package. Results revealed
that teachers had some amount of awareness but an inadequate
amount of information on disabilities and inclusive education.
Disability to most (37) teachers meant “an inability to do something”.
The difference between disability and handicap was stated by most as
former being cognitive while handicap being physical in nature. With
regard to Inclusive education, a large number (46) stated that they
were unaware of the term and did not know what it meant. Majority
(52) of them perceived maximum challenges for themselves in an
inclusive set up, and emphasized on the role of teacher training
courses in the area of providing knowledge (49) and training in
teaching methodology (53). Although, 83.3% of teachers held a
moderately positive attitude towards inclusive education, a large
percentage (61.6%) of participants felt that being in inclusive set up
would be very challenging for both children with special needs and
without special needs. Though, most (49) of the teachers stated that
children with special needs should be educated in regular classroom
but they further clarified that only those should be in a regular
classroom who have physical impairments of mild or moderate
degree.
Abstract: The research on thermoelectric has been a blooming field of research for the latest decade, owing to large amount of heat source available to be harvested, being eco-friendly and static in operation. This paper provides the performance of thermoelectric generator (TEG) with bulk material of bismuth telluride, Bi2Te3. Later, the performance of the TEGs is evaluated by considering attaching the TEGs on a plastic (polyethylene sheet) in contrast to the common method of attaching the TEGs on the metal surface.
Abstract: Lagos urban mini bus drivers play a critical role in the
transportation sector. The current major mode of transportation
within Lagos metropolis remains road transportation and this
confirms the relevance of urban mini-bus drivers in transporting the
populace to their various destinations. Other modes of transportation
such as the train and waterways are currently inadequate. Various
threats to the well-being of urban bus drivers include congested
traffic typical of modern day lifestyles, dwindling financial returns
due to long hours in traffic, fewer hours of sleep, inadequate diet,
time pressure, and assaults related to fare disputes. Several healthrelated
problems have been documented to be associated with urban
bus driving. For instance, greater rates of hypertension, obesity and
cholesterol level have been reported. Research studies are yet to
identify the influence of age and marital status on the well-being of
urban mini-bus drivers in Lagos metropolis. A study of this nature is
necessary as it is culturally perceived in Nigeria that older and
married people are especially influenced by family affiliation and
would behave in ways that would project positive outcomes. The
study sample consisted of 150 urban mini-bus drivers who were
conveniently sampled from six (6) different terminuses where their
journey begins and terminates. The well-being questionnaire was
administered to participants. The criteria for inclusion in the study
included the ability to read in English language and the confirmation
that interested participants were on duty and suited to be driving
mini-buses. Due to the nature of the job of bus driving, the researcher
administered the questionnaires on participants who were free and
willing to respond to the survey. All participants were males of
various age groups and of different marital statuses. Results of
analyses conducted revealed no significant influence of age and
marital status on the well-being of urban mini-bus drivers. This
indicates that the well-being of urban mini bus drivers is not
influenced by age or marital status. The findings of this study have
cultural implications. It negates the popularly held belief that older
and married people care more about their well-being than younger
and single people. It brings to fore the need to also identify and
consider other factors when certifying people for the job of urban bus
driving.
Abstract: Effective internal control system in the bursary unit of
tertiary educational institutions is geared toward achieving quality
teaching, learning and research environment and as well assist the
management of the institutions, particularly when decisions are to be
made. While internal control system exists in all institutions, the
outlined objectives above are far from being achieved. The paper
therefore assesses the effectiveness of internal control system in
tertiary educational institutions in Nasarawa State, Nigeria with
specific focus on the Nasarawa State Polytechnic, Lafia. The study is
survey, hence a simple closed ended questionnaire was developed
and administered to a sample of twenty seven (27) member staff from
the Bursary and the Internal audit unit of the Nasarawa State
Polytechnic, Lafia so as to obtain data for analysis purposes and to
test the study hypothesis. Responses from the questionnaire were
analysed using a simple percentage and chi square. Findings shows
that the right people are not assigned to the right job in the
department, budget, and management accounting were never used in
the institution’s operations and checking of subordinate by their
superior officers is not regular. This renders the current internal
control structure of the Polytechnic as ineffective and weak. The
paper therefore recommends that: transparency should be seen as
significant, as the institution work toward meeting its objectives, it
therefore means that the right staff be assigned the right job and
regular checking of the subordinates by their superiors be ensued.
Abstract: Synchrophasor technology is fast being deployed in
electric power grids all over the world and is fast changing the way
the grids are managed. This trend is to continue until the entire
power grids are fully connected so they can be monitored and
controlled in real-time. Much achievement has been made in the
synchrophasor technology development and deployment, and there
are still much more to be achieved. For instance, real-time power
grid control and protection potentials of synchrophasor are yet to be
explored. It is of necessity that researchers keep in view the various
challenges that still need to be overcome in expanding the frontiers
of synchrophasor technology. This paper outlines the major
challenges that should be dealt with in order to achieve the goal of
total power grid visualization, monitoring, and control using
synchrophasor technology.
Abstract: This study presents experimental and optimization of
nanoparticle mass concentration and heat input based on the total
thermal resistance (Rth) of loop heat pipe (LHP), employed for PCCPU
cooling. In this study, silica nanoparticles (SiO2) in water with
particle mass concentration ranged from 0% (pure water) to 1% is
considered as the working fluid within the LHP. The experimental
design and optimization is accomplished by the design of
experimental tool, Response Surface Methodology (RSM). The
results show that the nanoparticle mass concentration and the heat
input have significant effect on the Rth of LHP. For a given heat
input, the Rth is found to decrease with the increase of the
nanoparticle mass concentration up to 0.5% and increased thereafter.
It is also found that the Rth is decreased when the heat input is
increased from 20W to 60W. The results are optimized with the
objective of minimizing the Rth, using Design-Expert software, and
the optimized nanoparticle mass concentration and heat input are
0.48% and 59.97W, respectively, the minimum thermal resistance
being 2.66 (ºC/W).
Abstract: Introduction: The process to build a better safety
culture, methods of error analysis, and preventive measures, starts
with an understanding of the effects when human factors engineering
refer to remote microscopic diagnosis in surgery and specially in
organ transplantation for the remote evaluation of the grafts. It has
been estimated that even in well-organized transplant systems an
average of 8% to 14% of the grafts (G) that arrive at the recipient
hospitals may be considered as diseased, injured, damaged or
improper for transplantation. Digital microscopy adds information on
a microscopic level about the grafts in Organ Transplant (OT), and
may lead to a change in their management. Such a method will
reduce the possibility that a diseased G, will arrive at the recipient
hospital for implantation. Aim: Ergonomics of Digital Microscopy
(DM) based on virtual slides, on Telemedicine Systems (TS) for
Tele-Pathological (TPE) evaluation of the grafts (G) in organ
transplantation (OT). Material and Methods: By experimental
simulation, the ergonomics of DM for microscopic TPE of Renal
Graft (RG), Liver Graft (LG) and Pancreatic Graft (PG) tissues is
analyzed. In fact, this corresponded to the ergonomics of digital
microscopy for TPE in OT by applying Virtual Slide (VS) system for
graft tissue image capture, for remote diagnoses of possible
microscopic inflammatory and/or neoplastic lesions. Experimentation
included: a. Development of an OTE-TS similar Experimental
Telemedicine System (Exp.-TS), b. Simulation of the integration of
TS with the VS based microscopic TPE of RG, LG and PG applying
DM. Simulation of the DM based TPE was performed by 2
specialists on a total of 238 human Renal Graft (RG), 172 Liver Graft
(LG) and 108 Pancreatic Graft (PG) tissues digital microscopic
images for inflammatory and neoplastic lesions on four electronic
spaces of the four used TS. Results: Statistical analysis of specialist‘s
answers about the ability to diagnose accurately the diseased RG, LG
and PG tissues on the electronic space among four TS (A,B,C,D)
showed that DM on TS for TPE in OT is elaborated perfectly on the
ES of a Desktop, followed by the ES of the applied Exp.-TS. Tablet
and Mobile-Phone ES seem significantly risky for the application of
DM in OT (p
Abstract: Cancer is still one of the serious diseases threatening
the lives of human beings. How to have an early diagnosis and
effective treatment for tumors is a very important issue. The animal
carcinoma model can provide a simulation tool for the studies of
pathogenesis, biological characteristics, and therapeutic effects.
Recently, drug delivery systems have been rapidly developed to
effectively improve the therapeutic effects. Liposome plays an
increasingly important role in clinical diagnosis and therapy for
delivering a pharmaceutic or contrast agent to the targeted sites.
Liposome can be absorbed and excreted by the human body, and is
well known that no harm to the human body. This study aimed to
compare the therapeutic effects between encapsulated (doxorubicin
liposomal, Lipodox) and un-encapsulated (doxorubicin, Dox)
anti-tumor drugs using magnetic resonance imaging (MRI).
Twenty-four New Zealand rabbits implanted with VX2 carcinoma at
left thighs were classified into three groups: control group (untreated),
Dox-treated group, and LipoDox-treated group, 8 rabbits for each
group. MRI scans were performed three days after tumor implantation.
A 1.5T GE Signa HDxt whole body MRI scanner with a high
resolution knee coil was used in this study. After a 3-plane localizer
scan was performed, three-dimensional (3D) fast spin echo (FSE)
T2-weighted Images (T2WI) was used for tumor volumetric
quantification. Afterwards, two-dimensional (2D) spoiled gradient
recalled echo (SPGR) dynamic contrast-enhanced (DCE) MRI was
used for tumor perfusion evaluation. DCE-MRI was designed to
acquire four baseline images, followed by contrast agent Gd-DOTA
injection through the ear vein of rabbit. A series of 32 images were
acquired to observe the signals change over time in the tumor and
muscle. The MRI scanning was scheduled on a weekly basis for a
period of four weeks to observe the tumor progression longitudinally.
The Dox and LipoDox treatments were prescribed 3 times in the first
week immediately after the first MRI scan; i.e. 3 days after VX2 tumor
implantation. ImageJ was used to quantitate tumor volume and time
course signal enhancement on DCE images. The changes of tumor size
showed that the growth of VX2 tumors was effectively inhibited for
both LipoDox-treated and Dox-treated groups. Furthermore, the tumor
volume of LipoDox-treated group was significantly lower than that of
Dox-treated group, which implies that LipoDox has better therapeutic effect than Dox. The signal intensity of LipoDox-treated group is
significantly lower than that of the other two groups, which implies
that targeted therapeutic drug remained in the tumor tissue. This study
provides a radiation-free and non-invasive MRI method for
therapeutic monitoring of targeted liposome on an animal tumor
model.
Abstract: The traditional rhythms of the West African country
of Guinea have played a centuries-long role in defining the different
people groups that make up the country. Throughout their history,
before and since colonization by the French, the different ethnicities
have used their traditional music as a distinct part of their historical
identities. That is starting to change. Guinea is an impoverished
nation created in the early twentieth-century with little regard for the
history and cultures of the people who were included. The traditional
rhythms of the different people groups and their heritages have
remained. Fifteen individual traditional Guinean rhythms were
chosen to represent popular rhythms from the four geographical
regions of Guinea. Each rhythm was traced back to its native village
and video recorded on-site by as many different local performing
groups as could be located. The cyclical patterns rhythms were
transcribed via a circular, spatial design and then copied into a box
notation system where sounds happening at the same time could be
studied. These rhythms were analyzed for their consistency-overperformance
in a Fundamental Rhythm Pattern analysis so rhythms
could be compared for how they are changing through different
performances. The analysis showed that the traditional rhythm
performances of the Middle and Forest Guinea regions were the most
cohesive and showed the least evidence of change between
performances. The role of music in each of these regions is both
limited and focused. The Coastal and High Guinea regions have
much in common historically through their ethnic history and
modern-day trade connections, but the rhythm performances seem to
be less consistent and demonstrate more changes in how they are
performed today. In each of these regions the role and usage of music
is much freer and wide-spread. In spite of advances being made as a
country, different ethnic groups still frequently only respond and
participate (dance and sing) to the music of their native ethnicity.
There is some evidence that this self-imposed musical barrier is
beginning to change and evolve, partially through the development of
better roads, more access to electricity and technology, the nationwide
Ebola health crisis, and a growing self-identification as a
unified nation.
Abstract: The article deals with the readiness of military
professionals for challenging situations. It discusses higher
requirements on the psychical endurance of military professionals
arising from the specific nature of the military occupation, which is
typical for being very difficult to maintain regularity, which is in
accordance with the hygiene of work alternated by relaxation. The
soldier must be able to serve in the long term and constantly intense
performance that goes beyond human tolerance to stress situations. A
challenging situation is always associated with overcoming
difficulties, obstacles and complicated circumstances or using
unusual methods, ways and means to achieve the desired (expected)
objectives, performing a given task or satisfying an important need.
This paper describes the categories of challenging situations, their
classification and characteristics. Attention is also paid to the
formation of personality in challenging situations, coping with stress
in challenging situations, Phases of solutions of stressful situations,
resistance to challenging life situations and its factors. Finally, the
article is focused on increasing the readiness of military professionals
for challenging situations.