Abstract: In construction of any structure, the aesthetic and utility values should be considered in such a way as to make the structure cost-effective. Most structures are composed of elements and joints which are very critical in any skeletal space structure because they majorly determine the performance of the structure. In early times, most space structures were constructed using rigid joints which had the advantage of better performing structures as compared to pin-jointed structures but with the disadvantage of requiring all the construction work to be done on site. The discovery of semi-rigid joints now enables connections to be prefabricated and quickly assembled on site while maintaining good performance. In this paper, cost-effective is discussed basing on strength of connectors at the joints, buckling of joints and overall structure, and the effect of initial geometrical imperfections. Several existing joints are reviewed by classifying them into categories and discussing where they are most suited and how they perform structurally. Also, finite element modeling using ABAQUS is done to determine the buckling behavior. It is observed that some joints are more economical than others. The rise to span ratio and imperfections are also found to affect the buckling of the structures. Based on these, general principles that guide the design of cost-effective joints and structures are discussed.
Abstract: Most of ignition delay correlations studies have been
developed in a constant volume bombs which cannot capture the
dynamic variation in pressure and temperature during the ignition
delay as in real engines. Watson, Assanis et. al. and Hardenberg
and Hase correlations have been developed based on experimental
data of diesel engines. However, they showed limited predictive
ability of ignition delay when compared to experimental results. The
objective of the study was to investigate the dependency of ignition
delay time on engine brake power. An experimental investigation of
the effect of automotive diesel and water diesel emulsion fuels on
ignition delay under steady state conditions of a direct injection diesel
engine was conducted. A four cylinder, direct injection naturally
aspirated diesel engine was used in this experiment over a wide range
of engine speeds and two engine loads. The ignition delay
experimental data were compared with predictions of Assanis et. al.
and Watson ignition delay correlations. The results of the
experimental investigation were then used to develop a new ignition
delay correlation. The newly developed ignition delay correlation has
shown a better agreement with the experimental data than Assanis et.
al. and Watson when using automotive diesel and water diesel
emulsion fuels especially at low to medium engine speeds at both
loads. In addition, the second derivative of cylinder pressure which is
the most widely used method in determining the start of combustion
was investigated.
Abstract: Resource Discovery in Grids is critical for efficient
resource allocation and management. Heterogeneous nature and
dynamic availability of resources make resource discovery a
challenging task. As numbers of nodes are increasing from tens to
thousands, scalability is essentially desired. Peer-to-Peer (P2P)
techniques, on the other hand, provide effective implementation of
scalable services and applications. In this paper we propose a model
for resource discovery in Condor Middleware by using the four axis
framework defined in P2P approach. The proposed model enhances
Condor to incorporate functionality of a P2P system, thus aim to
make Condor more scalable, flexible, reliable and robust.
Abstract: In this paper, we propose a robust controller design method for discrete-time systems with sector-bounded nonlinearities and time-varying delay. Based on the Lyapunov theory, delaydependent stabilization criteria are obtained in terms of linear matrix inequalities (LMIs) by constructing the new Lyapunov-Krasovskii functional and using some inequalities. A robust state feedback controller is designed by LMI framework and a reciprocally convex combination technique. The effectiveness of the proposed method is verified throughout a numerical example.
Abstract: This paper presents design and characterization of a
microaccelerometer designated for integration into cataract surgical
probe to detect hardness of different eye tissues during cataract
surgery. Soft posterior lens capsule of eye can be easily damaged in
comparison with hard opaque lens since the surgeon can not see
directly behind cutting needle during the surgery. Presence of
microsensor helps the surgeon to avoid rupturing posterior lens
capsule which if occurs leads to severe complications such as
glaucoma, infection, or even blindness. The microsensor having
overall dimensions of 480 μm x 395 μm is able to deliver significant
capacitance variations during encountered vibration situations which
makes it capable to distinguish between different types of tissue.
Integration of electronic components on chip ensures high level of
reliability and noise immunity while minimizes space and power
requirements. Physical characteristics and results on performance
testing, proves integration of microsensor as an effective tool to aid
the surgeon during this procedure.
Abstract: The corrugated steel cladding used to cover most of
steel buildings is considered as non-structural element. This research
will reflect the effect of cladding as a shear diaphragm in increasing
the normal elastic capacity of columns. This study is important
because of the lack of information of the behavior of cladding and
secondary members in various codes. Mathematical models for six
different cases are carried by software. The results extracted from the
program have been plotted showing the effects of different variables
on the ultimate load of column. The variables considered in our
research are the spacing between columns and the thickness of the
corrugated sheet representing the sheet stiffness.
Abstract: This paper examines the forced convection flow of
incompressible, electrically conducting viscous fluid past a sharp
wedge in the presence of heat generation or absorption with an
applied magnetic field. The system of partial differential equations
governing Falkner - Skan wedge flow and heat transfer is first
transformed into a system of ordinary differential equations using
similarity transformations which is later solved using an implicit
finite - difference scheme, along with quasilinearization technique.
Numerical computations are performed for air (Pr = 0.7) and
displayed graphically to illustrate the influence of pertinent physical
parameters on local skin friction and heat transfer coefficients and,
also on, velocity and temperature fields. It is observed that the
magnetic field increases both the coefficients of skin friction and heat
transfer. The effect of heat generation or absorption is found to be
very significant on heat transfer, but its effect on the skin friction is
negligible. Indeed, the occurrence of overshoot is noticed in the
temperature profiles during heat generation process, causing the
reversal in the direction of heat transfer.
Abstract: We study bifurcation structure of the zonal jet flow the
streamfunction of which is expressed by a single spherical harmonics
on a rotating sphere. In the non-rotating case, we find that a steady
traveling wave solution arises from the zonal jet flow through Hopf
bifurcation. As the Reynolds number increases, several traveling
solutions arise only through the pitchfork bifurcations and at high
Reynolds number the bifurcating solutions become Hopf unstable. In
the rotating case, on the other hand, under the stabilizing effect of
rotation, as the absolute value of rotation rate increases, the number
of the bifurcating solutions arising from the zonal jet flow decreases
monotonically. We also carry out time integration to study unsteady
solutions at high Reynolds number and find that in the non-rotating
case the unsteady solutions are chaotic, while not in the rotating cases
calculated. This result reflects the general tendency that the rotation
stabilizes nonlinear solutions of Navier-Stokes equations.
Abstract: Energy consumption rate during the cooling process
of industrial glass tempering process is considerably high. In this
experimental study the effect of dimensionless jet to jet distance
(S/D) and jet to plate distance (H/D) on the cooling time have been
investigated. In the experiments 4 mm thick glass samples have been
used. Cooling unit consists of 16 mutually placed seamless aluminum
nozzles of 8 mm in diameter and 80 mm in length. Nozzles were in
staggered arrangement. Experiments were conducted with circular
jets for H/D values between 1 and 10, and for S/D values between 2
and 10. During the experiments Reynolds number has been kept
constant at 30000. Experimental results showed that the longest
cooling time with 87 seconds has been observed in the experiments
for S/D=10 and H/D=10 values, while the shortest cooling time with
42.5 seconds has been measured in the experiments for S/D=2 and
H/D=4 values.
Abstract: The current study has investigated the ageing
phenomena of silica optical fibres in relation to water activity which might be accelerated when exposed to a supplementary energy, such as microwaves. A controlled stress by winding fibres onto accurate
diameter mandrel was applied. Taking into account that normally a
decrease in fibre strength is induced in time by chemical action of water, the effects of cumulative reagents such as: water, applied stress and supplementary energy (microwave) in some cases acted in
the opposite manner. The microwave effect as a structural relaxation
catalyst appears unexpected, even if the overall gain in fibre strength is not high, but the stress corrosion factor revealed significant
increase in certain simulation conditions.
Abstract: A greenhouse experiment was conducted to investigate the effects of different types of nutrients induced salinity on the growth, membrane permeability, nitrate reductase activity, proline content and macronutrient concentrations of tomato plants. The plants were subjected to six different treatments: 1 (control) containing basic solution, 2 basic solution+40mM of NaCl, 3 basic solution+40 mM of KNO3, 4 basic solution+20 mM of Ca(NO3)2.4H2O, 5 basic solution+20 mM of Mg(NO3)2.6H2O and 6 basic solution+20 mM of KNO3+5 mM of Ca(NO3)2.4H2O+5 mM of Mg(NO3)2.6H2O. Membrane permeability was increased significantly only with addition of NaCl, and then decreased to its lower level with addition of Ca(NO3)2.4H2O and Mg(NO3)2.6H2O. Proline accumulation were followed the same trend of results when they had been exposed to NaCl salinity. Nitrate reductase activity (NRA) was significantly affected by addition of different types of nutrient induced salinity.
Abstract: Limited infrastructure development on peats and
organic soils is a serious geotechnical issues common to many
countries of the world especially Malaysia which distributed 1.5 mill
ha of those problematic soil. These soils have high water content and
organic content which exhibit different mechanical properties and
may also change chemically and biologically with time. Constructing
structures on peaty ground involves the risk of ground failure and
extreme settlement. Nowdays, much efforts need to be done in
making peatlands usable for construction due to increased landuse.
Deep mixing method employing cement as binders, is generally used
as measure again peaty/ organic ground failure problem. Where the
technique is widely adopted because it can improved ground
considerably in a short period of time. An understanding of
geotechnical properties as shear strength, stiffness and compressibility
behavior of these soils was requires before continues construction on
it. Therefore, 1- 1.5 meter peat soil sample from states of Johor and
an organic soil from Melaka, Malaysia were investigated. Cement
were added to the soil in the pre-mixing stage with water cement ratio
at range 3.5,7,14,140 for peats and 5,10,30 for organic soils,
essentially to modify the original soil textures and properties. The
mixtures which in slurry form will pour to polyvinyl chloride (pvc)
tube and cured at room temperature 250C for 7,14 and 28 days.
Laboratory experiments were conducted including unconfined
compressive strength and bender element , to monitor the improved
strength and stiffness of the 'stabilised mixed soils'. In between,
scanning electron miscroscopic (SEM) were observations to
investigate changes in microstructures of stabilised soils and to
evaluated hardening effect of a peat and organic soils stabilised
cement. This preliminary effort indicated that pre-mixing peat and
organic soils contributes in gaining soil strength while help the
engineers to establish a new method for those problematic ground
improvement in further practical and long term applications.
Abstract: In order to find the particular interaction energy
between cylcloguanil and the amino acids surrounding the pocket of
wild type and quadruple mutant type PfDHFR enzymes, the MP2
method with basis set 6-31G(d,p) level of calculations was
performed. The obtained interaction energies found that Asp54 has
the strongest interaction energy to both wild type and mutant type of -
12.439 and -11.250 kcal/mol, respectively and three amino acids;
Asp54, Ile164 and Ile14 formed the H-bonding with cycloguanil
drug. Importantly, the mutation at Ser108Asn was the key important
of cycloguanil resistant with showing repulsive interaction energy.
Abstract: A new analysis of perceptual speech enhancement is
presented. It focuses on the fact that if only noise above the masking
threshold is filtered, then noise below the masking threshold, but
above the absolute threshold of hearing, can become audible after the
masker filtering. This particular drawback of some perceptual filters,
hereafter called the maskee-to-audible-noise (MAN) phenomenon,
favours the emergence of isolated tonals that increase musical noise.
Two filtering techniques that avoid or correct the MAN phenomenon
are proposed to effectively suppress background noise without introducing
much distortion. Experimental results, including objective
and subjective measurements, show that these techniques improve
the enhanced speech quality and the gain they bring emphasizes the
importance of the MAN phenomenon.
Abstract: An efficient transient flow simulation for gas
pipelines and networks is presented. The proposed transient flow
simulation is based on the transfer function models and MATLABSimulink.
The equivalent transfer functions of the nonlinear
governing equations are derived for different types of the boundary
conditions. Next, a MATLAB-Simulink library is developed and
proposed considering any boundary condition type. To verify the
accuracy and the computational efficiency of the proposed
simulation, the results obtained are compared with those of the
conventional finite difference schemes (such as TVD, method of
lines, and other finite difference implicit and explicit schemes). The
effects of the flow inertia and the pipeline inclination are
incorporated in this simulation. It is shown that the proposed
simulation has a sufficient accuracy and it is computationally more
efficient than the other methods.
Abstract: Monitoring of microbial flora in aquacultured sea bream, in relation to the physicochemical parameters of the rearing seawater, ended to a model describing the influence of the last to the quality of the fisheries. Fishes were sampled during eight months from four aqua farms in Western Greece and analyzed for psychrotrophic, H2S producing bacteria, Salmonella sp., heterotrophic plate count (PCA), with simultaneous physical evaluation. Temperature, dissolved oxygen, pH, conductivity, TDS, salinity, NO3 - and NH4 + ions were recorded. Temperature, dissolved oxygen and conductivity were correlated, respectively, to PCA, Pseudomonas sp. and Shewanella sp. counts. These parameters were the inputs of the model, which was driving, as outputs, to the prediction of PCA, Vibrio sp., Pseudomonas sp. and Shewanella sp. counts, and fish microbiological quality. The present study provides, for the first time, a ready-to-use predictive model of fisheries hygiene, leading to an effective management system for the optimization of aquaculture fisheries quality.
Abstract: Mushrooms are a group of fleshy macroscopic fungi.
They have been valued throughout the world as both edible and
medicine. They are highly nutritious with good amount of quality
proteins, vitamins and minerals. An edible mushroom, Calocybe
indica was selected to validate its nutritional and medicinal
properties. Since tissue damage in hyperglycemia has been related to
oxidative stress, we evaluated the enzymatic and non-enzymatic
antioxidant status in the serum, liver and kidney since they are the
target organs in diabetic complications. From the results, increased
oxidative stress and decreased antioxidants might be related to the
causation of diabetes mellitus. The treatment in the diabetic rats with
the Calocybe indica showed an increase in the antioxidant system
and decrease in the production of free radicals. The mushrooms
which contain antioxidant phytochemicals has potential free radical
scavenging capacity and hence can induce the antioxidant system in
the body significantly reduces the generated free radicals thereby
maintaining the normal levels of the antioxidants
Abstract: The seismic feedback experiences in Algeria have
shown higher percentage of damages for non-code conforming
reinforced concrete (RC) buildings. Furthermore, the vulnerability of
these buildings was further aggravated due to presence of many
factors (e.g. weak the seismic capacity of these buildings, shorts
columns, Pounding effect, etc.).
Consequently Seismic risk assessments were carried out on
populations of buildings to identify the buildings most likely to
undergo losses during an earthquake. The results of such studies are
important in the mitigation of losses under future seismic events as
they allow strengthening intervention and disaster management plans
to be drawn up.
Within this paper, the state of the existing structures is assessed using
"the vulnerability index" method. This method allows the
classification of RC constructions taking into account both, structural
and non structural parameters, considered to be ones of the main
parameters governing the vulnerability of the structure. Based on
seismic feedback from past earthquakes DPM (damage probability
matrices) were developed too.
Abstract: A reliable estimate of the average bond stress within
the anchorage of steel reinforcing bars in tension is critically
important for the design of reinforced concrete member. This paper
describes part of a recently completed experimental research program
in the Centre for Infrastructure Engineering and Safety (CIES) at the
University of New South Wales, Sydney, Australia aimed at
assessing the effects of different factors on the anchorage
requirements of modern high strength steel reinforcing bars. The
study found that an increase in the anchorage length and bar diameter
generally leads to a reduction of the average ultimate bond stress. By
the extension of a well established analytical model of bond and
anchorage, it is shown here that the differences in the average
ultimate bond stress for different anchorage lengths is associated with
the variable degree of plastic deformation in the tensile zone of the
concrete surrounding the bar.
Abstract: In this paper, based on flume experimental data, the velocity distribution in open channel flows is re-investigated. From the analysis, it is proposed that the wake layer in outer region may be divided into two regions, the relatively weak outer region and the relatively strong outer region. Combining the log law for inner region and the parabolic law for relatively strong outer region, an explicit equation for mean velocity distribution of steady and uniform turbulent flow through straight open channels is proposed and verified with the experimental data. It is found that the sediment concentration has significant effect on velocity distribution in the relatively weak outer region.