Abstract: In this paper, a PSO-based approach is proposed to
derive a digital controller for redesigned digital systems having an interval plant based on resemblance of the extremal gain/phase
margins. By combining the interval plant and a controller as an interval system, extremal GM/PM associated with the loop transfer function
can be obtained. The design problem is then formulated as an optimization problem of an aggregated error function revealing the deviation on the extremal GM/PM between the redesigned digital
system and its continuous counterpart, and subsequently optimized by
a proposed PSO to obtain an optimal set of parameters for the digital controller. Computer simulations have shown that frequency
responses of the redesigned digital system having an interval plant bare a better resemblance to its continuous-time counter part by the incorporation of a PSO-derived digital controller in comparison to those obtained using existing open-loop discretization methods.
Abstract: With optimized bandwidth and latency discrepancy ratios, Node Gain Scores (NGSs) are determined and used as a basis for shaping the max-heap overlay. The NGSs - determined as the respective bandwidth-latency-products - govern the construction of max-heap-form overlays. Each NGS is earned as a synergy of discrepancy ratio of the bandwidth requested with respect to the estimated available bandwidth, and latency discrepancy ratio between the nodes and the source node. The tree leads to enhanceddelivery overlay multicasting – increasing packet delivery which could, otherwise, be hindered by induced packet loss occurring in other schemes not considering the synergy of these parameters on placing the nodes on the overlays. The NGS is a function of four main parameters – estimated available bandwidth, Ba; individual node's requested bandwidth, Br; proposed node latency to its prospective parent (Lp); and suggested best latency as advised by source node (Lb). Bandwidth discrepancy ratio (BDR) and latency discrepancy ratio (LDR) carry weights of α and (1,000 - α ) , respectively, with arbitrary chosen α ranging between 0 and 1,000 to ensure that the NGS values, used as node IDs, maintain a good possibility of uniqueness and balance between the most critical factor between the BDR and the LDR. A max-heap-form tree is constructed with assumption that all nodes possess NGS less than the source node. To maintain a sense of load balance, children of each level's siblings are evenly distributed such that a node can not accept a second child, and so on, until all its siblings able to do so, have already acquired the same number of children. That is so logically done from left to right in a conceptual overlay tree. The records of the pair-wise approximate available bandwidths as measured by a pathChirp scheme at individual nodes are maintained. Evaluation measures as compared to other schemes – Bandwidth Aware multicaSt architecturE (BASE), Tree Building Control Protocol (TBCP), and Host Multicast Tree Protocol (HMTP) - have been conducted. This new scheme generally performs better in terms of trade-off between packet delivery ratio; link stress; control overhead; and end-to-end delays.
Abstract: Determination of wellbore problems during a
production/injection process might be evaluated thorough
temperature log analysis. Other applications of this kind of log
analysis may also include evaluation of fluid distribution analysis
along the wellbore and identification of anomalies encountered
during production/injection process. While the accuracy of such
prediction is paramount, the common method of determination of a
wellbore temperature log includes use of steady-state energy balance
equations, which hardly describe the real conditions as observed in
typical oil and gas flowing wells during production operation; and
thus increase level of uncertainties. In this study, a practical method
has been proposed through development of a simplified semianalytical
model to apply for predicting temperature profile along the
wellbore. The developed model includes an overall heat transfer
coefficient accounting all modes of heat transferring mechanism,
which has been focused on the prediction of a temperature profile as
a function of depth for the injection/production wells. The model has
been validated with the results obtained from numerical simulation.
Abstract: This paper proposes a way to track persons by making use of multiple non-overlapping cameras. Tracking persons on multiple non-overlapping cameras enables data communication among cameras through the network connection between a camera and a computer, while at the same time transferring human feature data captured by a camera to another camera that is connected via the network. To track persons with a camera and send the tracking data to another camera, the proposed system uses a hierarchical human model that comprises a head, a torso, and legs. The feature data of the person being modeled are transferred to the server, after which the server sends the feature data of the human model to the cameras connected over the network. This enables a camera that captures a person's movement entering its vision to keep tracking the recognized person with the use of the feature data transferred from the server.
Abstract: Modern building automation needs to deal with very
different types of demands, depending on the use of a building and the
persons acting in it. To meet the requirements of situation awareness
in modern building automation, scenario recognition becomes more
and more important in order to detect sequences of events and to react
to them properly. We present two concepts of scenario recognition
and their implementation, one based on predefined templates and the
other applying an unsupervised learning algorithm using statistical
methods. Implemented applications will be described and their advantages
and disadvantages will be outlined.
Abstract: Solid oxide fuel cells have been considered in the last years as one of the most promising technologies for very highefficiency electric energy generation from hydrogen or other hydrocarbons, both with simple fuel cell plants and with integrated gas turbine-fuel cell systems. In the present study, a detailed thermodynamic analysis has been carried out. Mass and exergy balances are performed not only for the whole plant but also for each component in order to evaluate the thermal efficiency of combined cycle. Moreover, different sources of irreversibilities within the SOFC stack have been discussed and a parametric study conducted to evaluate the effect of temperature as well as pressure on SOFC irreversibilities and its performance. In this investigation methane and hydrogen have been used for fueling the SOFC stack and combustion chamber.
Abstract: As the remedy used music becomes active and
meditation effect through the music is verified, people take a growing
interest about psychological balance or remedy given by music. From
traditional studies, it is verified that the music of which spectral
envelop varies approximately as 1/f (f is frequency) down to a
frequency of low frequency bandwidth gives psychological balance.
In this paper, we researched signal properties of music which gives
psychological balance. In order to find this, we derived the property
from voice. Music composed by voice shows large value in NCSD.
We confirmed the degree of deference between music by curvature of
normalized cumulative spectral distribution. In the music that gives
psychological balance, the curvature shows high value, otherwise, the
curvature shows low value.
Abstract: The quantified residence time distribution (RTD)
provides a numerical characterization of mixing in a reactor, thus
allowing the process engineer to better understand mixing
performance of the reactor.This paper discusses computational
studies to investigate flow patterns in a two impinging streams
cyclone reactor(TISCR) . Flow in the reactor was modeled with
computational fluid dynamics (CFD). Utilizing the Eulerian-
Lagrangian approach, implemented in FLUENT (V6.3.22), particle
trajectories were obtained by solving the particle force balance
equations. From simulation results obtained at different Δts, the mean
residence time (tm) and the mean square deviation (σ2) were
calculated. a good agreement can be observed between predicted and
experimental data. Simulation results indicate that the behavior of
complex reactor systems can be predicted using the CFD technique
with minimum data requirement for validation.
Abstract: The increasing number of senior population gradually
causes to demand the use of information and communication
technology for their satisfactory lives. This paper presents the
development of an integrated TV based system which offers an
opportunity to provide value added services to a large number of
elderly citizens, and thus helps improve their quality of life. The
design philosophy underlying this paper is to fulfill both technological
and human aspects. The balance between these two dimensions has
been currently stressed as a crucial element for the design of usable
systems in real use, particularly to the elderly who have physical and
mental decline. As the first step to achieve it, we have identified
human and social factors that affect the elder-s quality of life by a
literature review, and based on them, build four fundamental services:
information, healthcare, learning and social network services.
Secondly, the system architecture, employed technologies and the
elderly-friendly system design considerations are presented. This
reflects technological and human perspectives in terms of the system
design. Finally, we describe some scenarios that illustrate the
potentiality of the proposed system to improve elderly people-s quality
of life.
Abstract: The purpose of the experiments described in this article was the comparison of integrated fixed film activated sludge (IFAS) and activated sludge (AS) system. The IFAS applied system consists of the cigarette filter rods (wasted filter in tobacco factories) as a biofilm carrier. The comparison with activated sludge was performed by two parallel treatment lines. Organic substance, ammonia and TP removal was investigated over four month period. Synthetic wastewater was prepared with ordinary tap water and glucose as the main sources of carbon and energy, plus balanced macro and micro nutrients. COD removal percentages of 94.55%, and 81.62% were achieved for IFAS and activated sludge system, respectively. Also, ammonia concentration significantly decreased by increasing the HRT in both systems. The average ammonia removal of 97.40 % and 96.34% were achieved for IFAS and activated sludge system, respectively. The removal efficiency of total phosphorus (TP-P) was 60.64%, higher than AS process by 56.63% respectively.
Abstract: In this paper, we apply the PQ theory with shunt active power filter in an unbalanced and distorted power system voltage to compensate the perturbations generated by non linear load. The power factor is also improved in the current source. The PLL system is used to extract the fundamental component of the even sequence under conditions mentioned of the power system voltage.
Abstract: Poly (ethylene glycol) (PEG) molecules attached to surfaces have shown high potential as a protein repellent due to their flexibility and highly water solubility. A quartz crystal microbalance recording frequency and dissipation changes (QCM-D) has been used to study the adsorption from aqueous solutions, of lysozyme and α-lactalbumin proteins (the last with and without calcium) onto modified stainless steel surfaces. Surfaces were coated with poly(ethylene imine) (PEI) and silicate before grafting on PEG molecules. Protein adsorption was also performed on the bare stainless steel surface as a control. All adsorptions were conducted at 23°C and pH 7.2. The results showed that the presence of PEG molecules significantly reduced the adsorption of lysozyme and α- lactalbumin (with calcium) onto the stainless steel surface. By contrast, and unexpected, PEG molecules enhanced the adsorption of α-lactalbumin (without calcium). It is suggested that the PEG -α- lactalbumin hydrophobic interaction plays a dominant role which leads to protein aggregation at the surface for this latter observation. The findings also lead to the general conclusion that PEG molecules are not a universal protein repellent. PEG-on-PEI surfaces were better at inhibiting the adsorption of lysozyme and α-lactalbumin (with calcium) than with PEG-on-silicate surfaces.
Abstract: The role of neighborhood center as semi public (the
balance space) is disappeared in bonding between private and public
in new urbanism. In this way, a hierarchical principle in the
traditional neighborhood center appears to create or develop the
conditions for residents` relationships and belonging. This paper
evaluates significant of hierarchical principles of the neighborhood
center in residents` territoriality and its factors. In this way Miandeh
neighborhood center from Boshrooyeh city was determined as a case
study area. Results indicated that a hierarchical principle is the best
instrument to improve the territoriality as the subcomponent of place
belonging in residents. The findings help the urban designer to
revitalization the neighborhoods and proceedings in organization of
physical space.
Abstract: This paper proposes a set of quasi-static mathematical
model of magnetic fields caused by high voltage conductors of
distribution transformer by using a set of second-order partial
differential equation. The modification for complex magnetic field
analysis and time-harmonic simulation are also utilized. In this
research, transformers were study in both balanced and unbalanced
loading conditions. Computer-based simulation utilizing the threedimensional
finite element method (3-D FEM) is exploited as a tool
for visualizing magnetic fields distribution volume a distribution
transformer. Finite Element Method (FEM) is one among popular
numerical methods that is able to handle problem complexity in
various forms. At present, the FEM has been widely applied in most
engineering fields. Even for problems of magnetic field distribution,
the FEM is able to estimate solutions of Maxwell-s equations
governing the power transmission systems. The computer simulation
based on the use of the FEM has been developed in MATLAB
programming environment.
Abstract: The design of an active leg orthosis for tumble
protection is proposed in this paper. The orthosis would be applied to
assist elders or invalids in rebalancing while they fall unexpectedly.
We observe the regain balance motion of healthy and youthful people,
and find the difference to elders or invalids. First, the physical model
of leg would be established, and we consider the leg motions are
achieve through four joints (phalanx stem, ankle, knee, and hip joint)
and five links (phalanges, talus, tibia, femur, and hip bone). To
formulate the dynamic equations, the coordinates which can clearly
describe the position in 3D space are first defined accordance with the
human movement of leg, and the kinematics and dynamics of the leg
movement can be formulated based on the robotics. For the purpose,
assisting elders and invalids in avoiding tumble, the posture variation
of unbalance and regaining balance motion are recorded by the
motion-capture image system, and the trajectory is taken as the desire
one. Then we calculate the force and moment of each joint based on
the leg motion model through programming MATLAB code. The
results would be primary information of the active leg orthosis design
for tumble protection.
Abstract: As the Textile Industry is the second largest industry
in Egypt and as small and medium-sized enterprises (SMEs) make up
a great portion of this industry therein it is essential to apply the
concept of Cleaner Production for the purpose of reducing pollution.
In order to achieve this goal, a case study concerned with ecofriendly
stone-washing of jeans-garments was investigated. A raw
material-substitution option was adopted whereby the toxic
potassium permanganate and sodium sulfide were replaced by the
environmentally compatible hydrogen peroxide and glucose
respectively where the concentrations of both replaced chemicals
together with the operating time were optimized. In addition, a
process-rationalization option involving four additional processes
was investigated. By means of criteria such as product quality,
effluent analysis, mass and heat balance; and cost analysis with the
aid of a statistical model, a process optimization treatment revealed
that the superior process optima were 50%, 0.15% and 50min for
H2O2 concentration, glucose concentration and time, respectively.
With these values the superior process ought to reduce the annual
cost by about EGP 105 relative to the currently used conventional
method.
Abstract: This paper presents a novel approach for representing
the spatio-temporal topology of the camera network with overlapping
and non-overlapping fields of view (FOVs). The topology is
determined by tracking moving objects and establishing object
correspondence across multiple cameras. To track people successfully
in multiple camera views, we used the Merge-Split (MS) approach for
object occlusion in a single camera and the grid-based approach for
extracting the accurate object feature. In addition, we considered the
appearance of people and the transition time between entry and exit
zones for tracking objects across blind regions of multiple cameras
with non-overlapping FOVs. The main contribution of this paper is to
estimate transition times between various entry and exit zones, and to
graphically represent the camera topology as an undirected weighted
graph using the transition probabilities.
Abstract: This paper describes an effective solution to the task
of a remote monitoring of super-extended objects (oil and gas
pipeline, railways, national frontier). The suggested solution is based
on the principle of simultaneously monitoring of seismoacoustic and
optical/infrared physical fields. The principle of simultaneous
monitoring of those fields is not new but in contrast to the known
solutions the suggested approach allows to control super-extended
objects with very limited operational costs. So-called C-OTDR
(Coherent Optical Time Domain Reflectometer) systems are used to
monitor the seismoacoustic field. Far-CCTV systems are used to
monitor the optical/infrared field. A simultaneous data processing
provided by both systems allows effectively detecting and classifying
target activities, which appear in the monitored objects vicinity. The
results of practical usage had shown high effectiveness of the
suggested approach.
Abstract: In this paper the performance of unified power flow
controller is investigated in controlling the flow of po wer over the
transmission line. Voltage sources model is utilized to study the
behaviour of the UPFC in regulating the active, reactive power and
voltage profile. This model is incorporated in Newton Raphson
algorithm for load flow studies. Simultaneous method is employed
in which equations of UPFC and the power balance equations of
network are combined in to one set of non-linear algebraic equations.
It is solved according to the Newton raphson algorithm. Case studies
are carried on standard 5 bus network. Simulation is done in Matlab.
The result of network with and without using UPFC are compared in
terms of active and reactive power flows in the line and active and
reactive power flows at the bus to analyze the performance of UPFC.
Abstract: The objective of the present investigation was to
evaluate the morphology of Escherchia coli bacteria in interaction
with SiO2 nanoparticles.
This study was made by atomic force microscopy and quartz
crystal microbalance using SiO2 nanoparticles with 10nm, 50nm and
100nm diameter and bacteria immobilized on polyelectrolyte
multilayer films obtained by spin coating or by “layer by layer”
(LbL) method.