Abstract: Verification of vented wooden façade system with
bonded joints is presented in this paper. The potential of bonded
joints is studied and described in more detail. The paper presents the results of an experimental and theoretical research about the effects of freeze cycling on the bonded joint. For the purpose of tests spruce
timber profiles were chosen for the load bearing substructure. Planks from wooden plastic composite and Siberian larch are representing facade cladding. Two types of industrial polyurethane adhesives intended for structural bonding were selected. The article is focused on the preparation as well as on the subsequent curing and conditioning of test samples. All test samples were subjected to 15 cycles that represents sudden temperature changes, i.e. immersion in a water bath at (293.15 ± 3) K for 6 hours and subsequent freezing to (253.15 ± 2) K for 18 hours. Furthermore, the retention of bond strength between substructure and cladding wastested and strength in shear was determined under tensile stress.Research data indicate that little, if any, damage to the bond results from freezingcycles. Additionally, the suitability of selected group of adhesives in combination with timber substructure was confirmed.
Abstract: The paper presents an innovative networked radar
system for detection of obstacles in a railway level crossing scenario.
This Monitoring System (MS) is able to detect moving or still
obstacles within the railway level crossing area automatically,
avoiding the need of human presence for surveillance. The MS is also
connected to the National Railway Information and Signaling System
to communicate in real-time the level crossing status. The
architecture is compliant with the highest Safety Integrity Level
(SIL4) of the CENELEC standard. The number of radar sensors used
is configurable at set-up time and depends on how large the level
crossing area can be. At least two sensors are expected and up four
can be used for larger areas. The whole processing chain that
elaborates the output sensor signals, as well as the communication
interface, is fully-digital, was designed in VHDL code and
implemented onto a Xilinx Virtex 6.
Abstract: There are several possibilities of reducing the required
amount of cement in concrete production. Natural zeolite is one of
the raw materials which can partly substitute Portland cement. The
effort to reduce the amount of Portland cement used in concrete
production is brings both economical as well as ecological benefits.
The paper presents the properties of concrete containing natural
zeolite as an active admixture in the concrete which partly substitutes
Portland cement. The properties discussed here bring information
about the basic mechanical properties and frost resistance of concrete
containing zeolite. The properties of concretes with the admixture of
zeolite are compared with a reference concrete with no content of
zeolite. The properties of the individual concretes are observed for
360 days.
Abstract: Background - The TrendCare Patient Dependency
System is currently used by a large number of maternity Services
across Australia, New Zealand and Singapore. In 2012, 2013 and
2014 validation studies were initiated in all three countries to validate
the acuity tools used for women in labour, and postnatal mothers and
babies. This paper will present the findings of the validation study.
Aim - The aim of this study was to; identify if the care hours
provided by the TrendCare acuity system was an accurate reflection
of the care required by women and babies; obtain evidence of
changes required to acuity indicators and/or category timings to
ensure the TrendCare acuity system remains reliable and valid across
a range of maternity care models in three countries.
Method - A non-experimental action research methodology was
used across maternity services in four District Health Boards in New
Zealand, a large tertiary and a large secondary maternity service in
Singapore and a large public maternity service in Australia.
Standardised data collection forms and timing devices were used to
collect midwife contact times, with women and babies included in the
study. Rejection processes excluded samples when care was not
completed/rationed, and contact timing forms were incomplete. The
variances between actual timed midwife/mother/baby contact and the
TrendCare acuity category times were identified and investigated.
Results - Thirty two (88.9%) of the 36 TrendCare acuity category
timings, fell within the variance tolerance levels when compared to
the actual timings recorded for midwifery care. Four (11.1%)
TrendCare categories provided less minutes of care than the actual
timings and exceeded the variance tolerance level. These were all
night shift category timings. Nine postnatal categories were not able
to be compared as the sample size for these categories was
statistically insignificant. 100% of labour ward TrendCare categories
matched actual timings for midwifery care, all falling within the
variance tolerance levels.
The actual time provided by core midwifery staff to assist lead
maternity carer (LMC) midwives in New Zealand labour wards
showed a significant deviation to previous studies. The findings of
the study demonstrated the need for additional time allocations in
TrendCare to accommodate an increased level of assistance given to
LMC midwives.
Conclusion - The results demonstrated the importance of regularly
validating the TrendCare category timings with actual timings of the
care hours provided. It was evident from the findings that variances
to models of care and length of stay in maternity units have increased
midwifery workloads on the night shift. The level of assistance
provided by the core labour ward staff to the LMC midwife has
increased substantially.
Outcomes - As a consequence of this study, changes were made to
the night duty TrendCare maternity categories, additional acuity
indicators were developed and times for assisting LMC midwives in
labour ward increased. The updated TrendCare version was delivered
to maternity services in 2014.
Abstract: This paper presents a study of SIW circuits (Substrate
Integrated Waveguide) with a rigorous and fast original approach
based on Iterative process (WCIP). The theoretical suggested study is
validated by the simulation of two different examples of SIW
circuits. The obtained results are in good agreement with those of
measurement and with software HFSS.
Abstract: The biodegradable family of polymers
polyhydroxyalkanoates is an interesting substitute for convectional
fossil-based plastics. However, the manufacturing and environmental
impacts associated with their production via intracellular bacterial
fermentation are strongly dependent on the raw material used and on
energy consumption during the extraction process, limiting their
potential for commercialization. Industrial wastewater is studied in
this paper as a promising alternative feedstock for waste valorization.
Based on results from laboratory and pilot-scale experiments, a
conceptual process design, techno-economic analysis and life cycle
assessment are developed for the large-scale production of the most
common type of polyhydroxyalkanoate, polyhydroxbutyrate.
Intracellular polyhydroxybutyrate is obtained via fermentation of
microbial community present in industrial wastewater and the
downstream processing is based on chemical digestion with
surfactant and hypochlorite. The economic potential and
environmental performance results help identifying bottlenecks and
best opportunities to scale-up the process prior to industrial
implementation. The outcome of this research indicates that the
fermentation of wastewater towards PHB presents advantages
compared to traditional PHAs production from sugars because the
null environmental burdens and financial costs of the raw material in
the bioplastic production process. Nevertheless, process optimization
is still required to compete with the petrochemicals counterparts.
Abstract: The problem of toughening in brittle materials
reinforced by fibers is complex, involving all of the mechanical
properties of fibers, matrix and the fiber/matrix interface, as well as
the geometry of the fiber. Development of new numerical methods
appropriate to toughening simulation and analysis is necessary. In
this work, we have performed simulations and analysis of toughening
in brittle matrix reinforced by randomly distributed fibers by means
of the discrete elements method. At first, we put forward a
mechanical model of toughening contributed by random fibers. Then
with a numerical program, we investigated the stress, damage and
bridging force in the composite material when a crack appeared in the
brittle matrix. From the results obtained, we conclude that: (i) fibers
of high strength and low elasticity modulus are beneficial to
toughening; (ii) fibers of relatively high elastic modulus compared to
the matrix may result in substantial matrix damage due to spalling
effect; (iii) employment of high-strength synthetic fibers is a good
option for toughening. We expect that the combination of the discrete
element method (DEM) with the finite element method (FEM) can
increase the versatility and efficiency of the software developed. The
present work can guide the design of ceramic composites of high
performance through the optimization of the parameters.
Abstract: The aim of software maintenance is to maintain
the software system in accordance with advancement in software
and hardware technology. One of the early works on software
maintenance is to extract information at higher level of abstraction. In
this paper, we present the process of how to design an information
extraction tool for software maintenance. The tool can extract the
basic information from old programs such as about variables, based
classes, derived classes, objects of classes, and functions. The tool
have two main parts; the lexical analyzer module that can read the
input file character by character, and the searching module which
users can get the basic information from the existing programs. We
implemented this tool for a patterned sub-C++ language as an input
file.
Abstract: Cloud computing is a new technology in industry and
academia. The technology has grown and matured in last half decade
and proven their significant role in changing environment of IT
infrastructure where cloud services and resources are offered over the
network. Cloud technology enables users to use services and
resources without being concerned about the technical implications of
technology. There are substantial research work has been performed
for the usage of cloud computing in educational institutes and
majority of them provides cloud services over high-end blade servers
or other high-end CPUs. However, this paper proposes a new stack
called “CiCKAStack” which provide cloud services over unutilized
computing resources, named as commodity computers.
“CiCKAStack” provides IaaS and PaaS using underlying commodity
computers. This will not only increasing the utilization of existing
computing resources but also provide organize file system, on
demand computing resource and design and development
environment.
Abstract: An innovative concept called “Flexy-Energy” is developing at 2iE. This concept aims to produce electricity at lower cost by smartly mix different available energy sources in accordance to the load profile of the region. With a higher solar irradiation and due to the fact that Diesel generator are massively used in sub-Saharan rural areas, PV/Diesel hybrid systems could be a good application of this concept and a good solution to electrify this region, provided they are reliable, cost effective and economically attractive to investors. Presentation of the developed approach is the aims of this paper. The PV/Diesel hybrid system designed consists to produce electricity and/or heat from a coupling between Diesel Diesel generators and PV panels without batteries storage, while ensuring the substitution of gasoil by bio-fuels available in the area where the system will be installed. The optimal design of this system is based on his technical performances; the Life Cycle Cost (LCC) and Levelized Cost of Energy are developed and use as economic criteria. The Net Present Value (NPV), the internal rate of return (IRR) and the discounted payback (DPB) are also evaluated according to dual electricity pricing (in sunny and unsunny hours). The PV/Diesel hybrid system obtained is compared to the standalone Diesel Diesel generators. The approach carried out in this paper has been applied to Siby village in Mali (Latitude 12 ° 23'N 8 ° 20'W) with 295 kWh as daily demand.This approach provides optimal physical characteristics (size of the components, number of component) and dynamical characteristics in real time (number of Diesel generator on, their load rate, fuel specific consumptions, and PV penetration rate) of the system. The system obtained is slightly cost effective; but could be improved with optimized tariffing strategies.
Abstract: Morphological interaction of porcine cumulus-oocyte
complexes (pCOCs) was investigated on in vitro condition using
electron microscope (SEM and TEM). The totals of 1,923 oocytes
were round in shape, surrounded by Zona pellucida with layer of
cumulus cells ranging between 59.29-202.14 μm in size. They were
classified into intact-, multi-, partial cumulus cell layer oocyte, and
completely denuded oocyte, at the percentage composition of 22.80%
32.70%, 18.60%, and 25.90 % respectively. The pCOCs classified as
intact- and multi cumulus cell layer oocytes were further culturing at
37°C with 5% CO2, 95% air atmosphere and high humidity for 44 h
in M199 with Earle’s salts supplemented with 10% HTFCS, 2.2
mg/mL NaHCO3, 1 M Hepes, 0.25 mM pyruvate, 15 μg/mL porcine
follicle-stimulating hormone, 1 μg/mL LH, 1μg/mL estradiol with
ethanol, and 50 μg/mL gentamycin sulfate. On electron microscope
study, cumulus cells were found to stick their processes to secrete
substance from the sac-shape end into Zona pellucida of the oocyte
and also communicated with the neighboring cells through their
microvilli on the beginning of incubation period. It is believed that
the cumulus cells communicate with the oocyte by inserting the
microvilli through this gap and embedded in the oocyte cytoplasm
before secreting substance, through the sac-shape end of the
microvilli, to inhibit primary oocyte development at the prophase I.
Morphological changes of the complexes were observed after
culturing for 24-44 h. One hundred percentages of the cumulus layers
were expanded and cumulus cells were peeling off from the oocyte
surface. In addition, the round-shape cumulus cells transformed
themselves into either an elongate shape or a columnar shape, and no
communication between cumulus neighboring cells. After 44 h of
incubation time, diameter of oocytes surrounded by cumulus cells
was larger than 0 h incubation. The effect of hormones in culture
medium is exerted by their receptors present in porcine oocyte. It is
likely that all morphological changes of the complexes after hormone
treatment were to allow maturation of the oocyte. This study
demonstrated that the association of hormones in M199 could
promote porcine follicle activation in 44 h in vitro condition. This
culture system should be useful for studying the regulation of early
follicular growth and development, especially because these follicles represent a large source of oocytes that could be used in vitro for cell
technology.
Abstract: In review the generalized data about biological
activity of anthraquinone-containing plants and specimens on their
basis is presented. Data of traditional medicine, results of
bioscreening and clinical researches of specimens are analyzed.
Abstract: There is a trend in development discourse to
understand and explain the level of corruption in Nigeria, its anticorruption
crusade and why it is failing, as well as its level of
compliance with International standards of United Nations
Convention against Corruption (UNCAC) & African Union
Convention on Converting and Preventing Corruption) to which
Nigeria is a signatory. This paper discusses the legal and
Constitutional provisions relating to corrupt practices and safeguards
in Nigeria, as well as the obstacles to the implementation of these
Conventions.
The paper highlights the challenges posed to the Anti-Corruption
crusade by analysing the loopholes that exist both in administrative
structure and in scope of the relevant laws. The paper argues that
Nigerian Constitution did not make adequate provisions for the
implementation of the conventions, hence a proposal which will
ensure adequate provision for implementing the conventions to better
the lives of Nigerians. The paper concludes that there is the need to
build institutional parameters, adequate constitutional and structural
safeguards, as well as to synergise strategies, collaborations and
alliances to facilitate the timely domestication and implementation of
the conventions.
Abstract: In review the generalized data about biosynthetic routs
formation anthraquinone molecules in natural cells. The basic
possibilities of various ways of biosynthesis of different quinoid
substances are shown.
Abstract: The Al-MoO3-P-CdTe-Al MOS sandwich structures
were fabricated by vacuum deposition method on cleaned glass
substrates. Capacitance versus voltage measurements were performed
at different frequencies and sweep rates of applied voltages for oxide
and semiconductor films of different thicknesses. In the negative
voltage region of the C-V curve a high differential capacitance of the
semiconductor was observed and at high frequencies (
Abstract: Hybrid bioreactor having both suspended-growth and
attached-growth bacteria is found a novel and excellent bioreactor
system for treating the municipal wastewater containing inhibitory
substrates too. In this reactor a fraction of substrate is used by
suspended biomass and the remaining by attached biomass resulting
in the competition between the two growths for the substrate. The
combination of suspended and attached growth provides the system
with enhanced biomass concentration and sludge age more than those
in ASP. Similar to attached growth system, the hybrid bioreactor
ensures considerable efficiency for treating toxic and refractory
substances in wastewater. For the process design of hybrid bioreactor
a suitable mathematical model is required. Although various
mathematical models were developed on hybrid bioreactor in due
course of time in earlier research works, none of them was found
having a specific simplified solution of the corresponding models and
without having any drawback. To overcome this drawback authors
already developed a simplified mathematical model for process
design of a hybrid bioreactor. The present paper briefly highlights on
the various aspects of process design of an aerobic hybrid bioreactor
for the treatment of municipal wastewater.
Abstract: One of the best examples, in evolution of the public
procurement, from post-soviet countries are reforms carried out in
Georgia, which brought them close to international standards of
procurement. In Georgia, public procurement legislation started
functioning short after gaining independence. The reform has passed
several stages and came in the form as it is today. It should also be
noted, that countries with economy in transition, including Georgia,
implemented all the reforms in public procurement based on
recommendations and support of World Bank, the United Nations
and other international organizations.
The aim of first adopted law was regulation of the procurement
process of budget-organizations, transparency and creation of
competitive environment for private companies to access state funds
legally. The priorities were identified quite clearly in the wording of
the law, but operation/function of this law could not be reached on its
level, because of some objective and subjective reasons. The high
level of corruption in all levels of governance can be considered as a
main obstacle reason and of course, it is natural, that it had direct
impact on the procurement process, as well as on transparency and
rational use of state funds. These circumstances were the reasons that
reforms in this sphere continued, to improve procurement process, in
particular, the first wave of reforms began after several years. Public
procurement agency carried out reform with World Bank with main
purpose of smartening the procurement legislation and its
harmonization with international treaties and agreements. Also with
the support of World Bank various activities were carried out to raise
awareness of participants involved in procurement system.
Further major changes in the legislation were filed bit later, which
was also directed towards the improvement and smarten of the
procurement process. The third wave of the reform more or less
guaranteed the transparency of the procurement process, which later
became the basis for the rational spending of state funds. The reform
of the procurement system completely changed the procedures.
Carried out reform in Georgia resulted in introducing new
electronic tendering system, which benefit the transparency of the
process, after this became the basis for the further development of a
competitive environment, which become a prerequisite for the state
rational spending. Increased number of supplier organizations
participating in the procurement process resulted in reduction of the
estimated cost and the actual cost.
Assessment of the reforms in Georgia in the field of public
procurement can be concluded, that proper regulation of the sector
and relevant policy may proceed to rational and transparent spending
of the budget from country’s state institutions. Also, the business
sector has the opportunity to work in competitive market conditions
and to make a preliminary analysis, which is a prerequisite for future
strategy and development.
Abstract: In the framework of the modernization of the city of
Constantine and in order to restore its status as a regional metropolis
introducing it into the network of cities international metropolises,
has major urban project was launched: project of modernization and
of metropolitanization of the city of Constantine.
Our research project focuses on the management of the project for
the modernization of the city of Constantine (PMMC) focusing on
the management of some aspects of the urban project whose
participation, with the objective assessment of the managerial
approach business.
In this contribution, we focus on two cases revealing taken into
account in our research work on the question of participation of
actors and their organizations. It is "the urban project of
modernization of Constantine" and the operation relating to "the
urban improvement in the city of the Brothers FERRAD in the
district of Zouaghi". This project and this operation with the objective
of improving the living conditions of citizens have faced several
challenges and obstacles that have been in major part the factors of its
failures.
Through this study, we examined the management process and the
mode of organization of the actors of the project as well as the level
of participation of the citizen to finally proposed managerial solutions
toconflict situations observed.
Abstract: Previous studies on financial distress prediction choose
the conventional failing and non-failing dichotomy; however, the
distressed extent differs substantially among different financial
distress events. To solve the problem, “non-distressed”, “slightlydistressed”
and “reorganization and bankruptcy” are used in our article
to approximate the continuum of corporate financial health. This paper
explains different financial distress events using the two-stage method.
First, this investigation adopts firm-specific financial ratios, corporate
governance and market factors to measure the probability of various
financial distress events based on multinomial logit models.
Specifically, the bootstrapping simulation is performed to examine the
difference of estimated misclassifying cost (EMC). Second, this work
further applies macroeconomic factors to establish the credit cycle
index and determines the distressed cut-off indicator of the two-stage
models using such index. Two different models, one-stage and
two-stage prediction models are developed to forecast financial
distress, and the results acquired from different models are compared
with each other, and with the collected data. The findings show that the
one-stage model has the lower misclassification error rate than the
two-stage model. The one-stage model is more accurate than the
two-stage model.
Abstract: This paper addresses the issue of the autonomous
mobile robot (AMR) navigation task based on the hybrid control
modes. The novel hybrid control mode, based on multi-sensors
information by using the fuzzy approach, has been presented in this
research. The system operates in real time, is robust, enables the robot
to operate with imprecise knowledge, and takes into account the
physical limitations of the environment in which the robot moves,
obtaining satisfactory responses for a large number of different
situations. An experiment is simulated and carried out with a pioneer
mobile robot. From the experimental results, the effectiveness and
usefulness of the proposed AMR obstacle avoidance and navigation
scheme are confirmed. The experimental results show the feasibility,
and the control system has improved the navigation accuracy. The
implementation of the controller is robust, has a low execution time,
and allows an easy design and tuning of the fuzzy knowledge base.