Abstract: Fundamental motivation of this paper is how gaze estimation can be utilized effectively regarding an application to games. In games, precise estimation is not always important in aiming targets but an ability to move a cursor to an aiming target accurately is also significant. Incidentally, from a game producing point of view, a separate expression of a head movement and gaze movement sometimes becomes advantageous to expressing sense of presence. A case that panning a background image associated with a head movement and moving a cursor according to gaze movement can be a representative example. On the other hand, widely used technique of POG estimation is based on a relative position between a center of corneal reflection of infrared light sources and a center of pupil. However, a calculation of a center of pupil requires relatively complicated image processing, and therefore, a calculation delay is a concern, since to minimize a delay of inputting data is one of the most significant requirements in games. In this paper, a method to estimate a head movement by only using corneal reflections of two infrared light sources in different locations is proposed. Furthermore, a method to control a cursor using gaze movement as well as a head movement is proposed. By using game-like-applications, proposed methods are evaluated and, as a result, a similar performance to conventional methods is confirmed and an aiming control with lower computation power and stressless intuitive operation is obtained.
Abstract: the intension in this work is to investigate the effect of
different bending manifold pipes on engine performance for different
engine speed. Power, Torque, and BSFC were calculated and
presented to show the effect of varying bending pipes angles on them
for all cases considered. A special program used to carry out the
calculations. A simulation model for 4-cylinders spark ignition
engine with turbocharger has been built and calculated. The analysis
of the results shows that for 120o angle the torque increases about
40% at 3000 rpm and 25% at 4000 rpm without changing in fuel
consumption. For 90o angle the increment in torque is about 10 %.
For the same bending angle the increment in brake power is around
40% at 3000 rpm and 25% at 4000 rpm. The increment in fuel
consumption is about 12% for 60o and 30% for 90o between (6000-
7000) rpm.
Abstract: In this study, we discussed the effects on the thermal
comfort of super high-rise residences that how effected by the high
thermal capacity structural components. We considered different
building orientations, structures, and insulation methods. We used the
dynamic simulation software THERB (simulation of the thermal
environment of residential buildings). It can estimate the temperature,
humidity, sensible temperature, and heating/cooling load for multiple
buildings. In the past studies, we examined the impact of
air-conditioning loads (hereinafter referred to as AC loads) on the
interior structural parts and the AC-usage patterns of super-high-rise
residences.
Super-high-rise residences have more structural components such
as pillars and beams than do ordinary apartment buildings. The
skeleton is generally made of concrete and steel, which have high
thermal-storage capacities. The thermal-storage capacity of
super-high-rise residences is considered to have a larger impact on the
AC load and thermal comfort than that of ordinary residences.
We show that the AC load of super-high-rise units would be
reduced by installing insulation on the surfaces of interior walls that
are not usually insulated in Japan.
Abstract: This paper proposes an efficient learning method for the layered neural networks based on the selection of training data and input characteristics of an output layer unit. Comparing to recent neural networks; pulse neural networks, quantum neuro computation, etc, the multilayer network is widely used due to its simple structure. When learning objects are complicated, the problems, such as unsuccessful learning or a significant time required in learning, remain unsolved. Focusing on the input data during the learning stage, we undertook an experiment to identify the data that makes large errors and interferes with the learning process. Our method devides the learning process into several stages. In general, input characteristics to an output layer unit show oscillation during learning process for complicated problems. The multi-stage learning method proposes by the authors for the function approximation problems of classifying learning data in a phased manner, focusing on their learnabilities prior to learning in the multi layered neural network, and demonstrates validity of the multi-stage learning method. Specifically, this paper verifies by computer experiments that both of learning accuracy and learning time are improved of the BP method as a learning rule of the multi-stage learning method. In learning, oscillatory phenomena of a learning curve serve an important role in learning performance. The authors also discuss the occurrence mechanisms of oscillatory phenomena in learning. Furthermore, the authors discuss the reasons that errors of some data remain large value even after learning, observing behaviors during learning.
Abstract: Web sites are rapidly becoming the preferred media
choice for our daily works such as information search, company
presentation, shopping, and so on. At the same time, we live in a
period where visual appearances play an increasingly important
role in our daily life. In spite of designers- effort to develop a web
site which be both user-friendly and attractive, it would be difficult
to ensure the outcome-s aesthetic quality, since the visual
appearance is a matter of an individual self perception and opinion.
In this study, it is attempted to develop an automatic system for
web pages aesthetic evaluation which are the building blocks of
web sites. Based on the image processing techniques and artificial
neural networks, the proposed method would be able to categorize
the input web page according to its visual appearance and aesthetic
quality. The employed features are multiscale/multidirectional
textural and perceptual color properties of the web pages, fed to
perceptron ANN which has been trained as the evaluator. The
method is tested using university web sites and the results
suggested that it would perform well in the web page aesthetic
evaluation tasks with around 90% correct categorization.
Abstract: It is well known that the abrasive particles in the
abrasive water suspension has significant effect on the erosion
characteristics of the inside surface of the nozzle. Abrasive particles
moving with the flow cause severe skin friction effect, there by
altering the nozzle diameter due to wear which in turn reflects on the
life of the nozzle for effective machining. Various commercial
abrasives are available for abrasive water jet machining. The erosion
characteristic of each abrasive is different. In consideration of this
aspect, in the present work, the effect of abrasive materials namely
garnet, aluminum oxide and silicon carbide on skin friction
coefficient due to wall shear stress and jet kinetic energy has been
analyzed. It is found that the abrasive material of lower density
produces a relatively higher skin friction effect and higher jet exit
kinetic energy.
Abstract: This paper describes the smart energy monitoring system with a wireless sensor network for monitoring of electrical usage in smart house. Proposed system is composed of wireless plugs and energy control wallpad server. The wireless plug integrates an AC power socket, a relay to switch the socket ON/OFF, a Hall effect sensor to sense current of load appliance and a Kmote. The Kmote is a wireless communication interface based on TinyOS. We evaluated wireless plug in a laboratory, analyzed and presented energy consumption data from electrical appliances for 3 months in home.
Abstract: The Lattice Boltzmann Method (LBM) with double populations is applied to solve the steady-state laminar natural convective heat transfer in a triangular cavity filled with water. The bottom wall is heated, the vertical wall is cooled, and the inclined wall is kept adiabatic. The buoyancy effect was modeled by applying the Boussinesq approximation to the momentum equation. The fluid velocity is determined by D2Q9 LBM and the energy equation is discritized by D2Q4 LBM to compute the temperature field. Comparisons with previously published work are performed and found to be in excellent agreement. Numerical results are obtained for a wide range of parameters: the Rayleigh number from to and the inclination angle from 0° to 360°. Flow and thermal fields were exhibited by means of streamlines and isotherms. It is observed that inclination angle can be used as a relevant parameter to control heat transfer in right-angled triangular enclosures.
Abstract: The aim of this study is to analyze influence of
differences of heat insulation methods on indoor thermal environment and comfort of apartment buildings.
This study analyzes indoor thermal environment and comfort on units of apartment buildings using calculation software "THERB" and
compares three different kinds of heat insulation methods. Those are
outside insulation on outside walls, inside insulation on outside walls and interior insulation. In terms of indoor thermal environment, outside insulation is the best to stabilize room temperature. In winter, room temperature on
outside insulation after heating is higher than other and it is kept 3-5 degrees higher through all night. But the surface temperature with
outside insulation did not dramatically increase when heating was used, which was 3 to 5oC lower than the temperature with other
insulation. The PMV of interior insulation fall nearly range of comfort when the heating and cooling was use.
Abstract: A 1.2 V, 0.61 mA bias current, low noise amplifier
(LNA) suitable for low-power applications in the 2.4 GHz band is
presented. Circuit has been implemented, laid out and simulated using
a UMC 130 nm RF-CMOS process. The amplifier provides a 13.3 dB
power gain a noise figure NF< 2.28 dB and a 1-dB compression point
of -15.69 dBm, while dissipating 0.74 mW. Such performance make
this design suitable for wireless sensor networks applications such as
ZigBee.
Abstract: In this paper a novel method was presented for
evaluating the fabric pills using digital image processing techniques. This work provides a novel technique for
detecting pills and also measuring their heights, surfaces and
volumes. Surely, measuring the intensity of defects by human vision is an inaccurate method for quality control; as a result, this problem became a motivation for employing digital image processing techniques for detection of defects of fabric
surface. In the former works, the systems were just limited to measuring of the surface of defects, but in the presented
method the height and the volume of defects were also
measured, which leads to a more accurate quality control. An algorithm was developed to first, find pills and then measure their average intensity by using three criteria of height, surface
and volume. The results showed a meaningful relation
between the number of rotations and the quality of pilled fabrics.
Abstract: The main objectives of this paper are to measure
pollutants concentrations in the oil refinery area in Kuwait over three
periods during one year, obtain recent emission inventory for the
three refineries of Kuwait, use AERMOD and the emission inventory
to predict pollutants concentrations and distribution, compare model
predictions against measured data, and perform numerical
experiments to determine conditions at which emission rates and the
resulting pollutant dispersion is below maximum allowable limits.
Abstract: Mechanical and water transport properties of high
performance concrete (HPC) containing natural zeolite as partial
replacement of Portland cement are studied. Experimental results
show that in the investigated mixes the use of natural zeolite leads to
an increase of porosity, decrease of compressive strength and
increase of moisture diffusivity and water vapor diffusion coefficient,
as compared with the reference HPC. However, for the replacement
level up to 20% of the mass of Portland cement the concretes still
maintain their high performance character and exhibit acceptable
water transport properties. Therefore, natural zeolite can be
considered an environmental friendly binder with a potential to
replace a part of Portland cement in concrete in building industry.
Abstract: Knowledge about the magnetic quantities in a magnetic circuit is always of great interest. On the one hand, this information is needed for the simulation of a transformer. On the other hand, parameter studies are more reliable, if the magnetic quantities are derived from a well established model. One possibility to model the 3-phase transformer is by using a magnetic equivalent circuit (MEC). Though this is a well known system, it is often not an easy task to set up such a model for a large number of lumped elements which additionally includes the nonlinear characteristic of the magnetic material. Here we show the setup of a solver for a MEC and the results of the calculation in comparison to measurements taken. The equations of the MEC are based on a rearranged system of the nodal analysis. Thus it is possible to achieve a minimum number of equations, and a clear and simple structure. Hence, it is uncomplicated in its handling and it supports the iteration process. Additional helpful tasks are implemented within the solver to enhance the performance. The electric circuit is described by an electric equivalent circuit (EEC). Our results for the 3-phase transformer demonstrate the computational efficiency of the solver, and show the benefit of the application of a MEC.
Abstract: A theoretical study is conducted to design and explore
the effect of different parameters such as heat loads, the tube size of
piping system, wick thickness, porosity and hole size on the
performance and capability of a Loop Heat Pipe(LHP). This paper
presents a steady state model that describes the different phenomena
inside a LHP. Loop Heat Pipes(LHPs) are two-phase heat transfer
devices with capillary pumping of a working fluid. By their original
design comparing with heat pipes and special properties of the
capillary structure, they-re capable of transferring heat efficiency for
distances up to several meters at any orientation in the gravity field,
or to several meters in a horizontal position. This theoretical model is
described by different relations to satisfy important limits such as
capillary and nucleate boiling. An algorithm is developed to predict
the size of the LHP satisfying the limitations mentioned above for a
wide range of applied loads. Finally, to assess and evaluate the
algorithm and all the relations considered, we have used to design a
new kind of LHP to recover the heat from the exhaust of an actual
Gas Turbine. By finding the results, it showed that we can use the
LHP as a very high efficient device to recover the heat even in high
amount of loads(exhaust of a gas turbine). The sizes of all parts of the
LHP were obtained using the developed algorithm.
Abstract: The main focus of this paper is on the human induced
forces. Almost all existing force models for this type of load (defined
either in the time or frequency domain) are developed from the
assumption of perfect periodicity of the force and are based on force
measurements conducted on rigid (i.e. high frequency) surfaces. To
verify the different authors conclusions the vertical pressure
measurements invoked during the walking was performed, using
pressure gauges in various configurations. The obtained forces are
analyzed using Fourier transformation. This load is often decisive in
the design of footbridges. Design criteria and load models proposed
by widely used standards and other researchers were introduced and a
comparison was made.
Abstract: Numerous experimental tests for post-installed anchor systems drilled in hardened concrete were conducted in order to estimate pull-out and shear strength accounting for uncertainties such as torque ratios, embedment depths and different diameters in demands. In this study, the strength of the systems was significantly changed by the effect of those three uncertainties during pull-out experimental tests, whereas the shear strength of the systems was not affected by torque ratios. It was also shown that concrete cone failure or damage mechanism was generally investigated during and after pull-out tests and in shear strength tests, mostly the anchor systems were failed prior to failure of primary structural system. Furthermore, 3D finite element model for the anchor systems was created by ABAQUS for the numerical analysis. The verification of finite element model was identical till the failure points to the load-displacement relationship specified by the experimental tests.
Abstract: Optical Coherence Tomography (OCT) combined
with the Confocal Microscopy, as a noninvasive method, permits the
determinations of materials defects in the ceramic layers depth. For
this study 256 anterior and posterior metal and integral ceramic fixed
partial dentures were used, made with Empress (Ivoclar), Wollceram
and CAD/CAM (Wieland) technology. For each investigate area 350
slices were obtain and a 3D reconstruction was perform from each
stuck. The Optical Coherent Tomography, as a noninvasive method,
can be used as a control technique in integral ceramic technology,
before placing those fixed partial dentures in the oral cavity. The
purpose of this study is to evaluate the capability of En face Optical
Coherence Tomography (OCT) combined with a fluorescent method
in detection and analysis of possible material defects in metalceramic
and integral ceramic fixed partial dentures. As a conclusion,
it is important to have a non invasive method to investigate fixed
partial prostheses before their insertion in the oral cavity in order to
satisfy the high stress requirements and the esthetic function.
Abstract: Nylon 6-clay hybrid/neat nylon 6, sheath/core
bicomponent nanocomposite fibers containing 4 wt% of clay in
sheath section were melt spun at different take-up speeds. Their
orientation and crystalline structure were compared to those of neat
nylon 6 fibers. Birefringence measurements showed that the
orientation development in sheath and core parts of bicomponent
fibers was different. Crystallinity results showed that clay did not act
as a nucleating agent for bicomponent fibers. The neat nylon 6 fiber
had a smooth surface while striped pattern was appeared on the
surface of bicomponent fiber containing clay due to thermal
shrinkage of the core part.
Abstract: Segmentation in ultrasound images is challenging due to the interference from speckle noise and fuzziness of boundaries. In this paper, a segmentation scheme using fuzzy c-means (FCM) clustering incorporating both intensity and texture information of images is proposed to extract breast lesions in ultrasound images. Firstly, the nonlinear structure tensor, which can facilitate to refine the edges detected by intensity, is used to extract speckle texture. And then, a spatial FCM clustering is applied on the image feature space for segmentation. In the experiments with simulated and clinical ultrasound images, the spatial FCM clustering with both intensity and texture information gets more accurate results than the conventional FCM or spatial FCM without texture information.