Abstract: The knowledge of biodiesel density over large ranges
of temperature and pressure is important for predicting the behavior
of fuel injection and combustion systems in diesel engines, and for
the optimization of such systems. In this study, cottonseed oil was
transesterified into biodiesel and its density was measured at
temperatures between 288 K and 358 K and pressures between 0.1
MPa and 30 MPa, with expanded uncertainty estimated as ±1.6 kg⋅m-
3. Experimental pressure-volume-temperature (pVT) cottonseed data
was used along with literature data relative to other 18 biodiesels, in
order to build a database used to test the correlation of density with
temperarure and pressure using the Goharshadi–Morsali–Abbaspour
equation of state (GMA EoS). To our knowledge, this is the first that
density measurements are presented for cottonseed biodiesel under
such high pressures, and the GMA EoS used to model biodiesel
density. The new tested EoS allowed correlations within 0.2 kg·m-3
corresponding to average relative deviations within 0.02%. The built
database was used to develop and test a new full predictive model
derived from the observed linear relation between density and degree
of unsaturation (DU), which depended from biodiesel FAMEs
profile. The average density deviation of this method was only about
3 kg.m-3 within the temperature and pressure limits of application.
These results represent appreciable improvements in the context of
density prediction at high pressure when compared with other
equations of state.
Abstract: In this paper a novel design of aerostatic thrust bearing
is proposed and is analyzed numerically. The capillary restrictor and
bearing disk are made of elastomer like silicone and PU. The
viscoelasticity of elastomer helps the capillary expand for more air
flux and at the same time, allows conicity of the bearing surface to
form when the air pressure is enhanced. Therefore the bearing has the
better ability of passive compensation. In the present example, as
compared with the typical model, the new designs can nearly double
the load capability and offer four times static stiffness.
Abstract: This paper represents performance of particle swarm
optimisation (PSO) algorithm based integral (I) controller and
proportional-integral controller (PI) for interconnected hydro-thermal
automatic generation control (AGC) with generation rate constraint
(GRC) and Thyristor controlled phase shifter (TCPS) in series with
tie line. The control strategy of TCPS provides active control of
system frequency. Conventional objective function integral square
error (ISE) and another objective function considering square of
derivative of change in frequencies of both areas and change in tie
line power are considered. The aim of designing the objective
function is to suppress oscillation in frequency deviations and change
in tie line power oscillation. The controller parameters are searched
by PSO algorithm by minimising the objective functions. The
dynamic performance of the controllers I and PI, for both the
objective functions, are compared with conventionally optimized I
controller.
Abstract: This paper reports the numerical and experimental
performances of Double Glass Wall are investigated. Two
configurations were considered namely, the Double Clear Glass Wall
(DCGW) and the Double Translucent Glass Wall (DTGW). The
coupled governing equations as well as boundary conditions are
solved using the finite element method (FEM) via COMSOLTM
Multiphysics. Temperature profiles and flow field of the DCGW and
DTGW are reported and discussed. Different constant heat fluxes
were considered as 400 and 800 W.m-2 the corresponding initial
condition temperatures were 30.5 and 38.5ºC respectively. The
results show that the simulation results are in agreement with the
experimental data. Conclusively, the model considered in this study
could reasonable be used simulate the thermal and ventilation
performance of the DCGW and DTGW configurations.
Abstract: In this research article a comprehensive investigation
has been carried out to determine the effect of thermal cycle on
temperature dependent process parameters developed during gas
tungsten arc (GTA) welding of high carbon (AISI 1090) steel butt
joints. An experiment based thermal analysis has been performed to
obtain the thermal history. We have focused on different
thermophysical properties such as thermal conductivity, heat transfer
coefficient and cooling rate. Angular torch model has been utilized to
find out the surface heat flux and its variation along the fusion zone as
well as along the longitudinal direction from fusion boundary. After
welding and formation of weld pool, heat transfer coefficient varies
rapidly in the vicinity of molten weld bead and heat affected zone. To
evaluate the heat transfer coefficient near the fusion line and near the
rear end of the plate (low temperature region), established correlation
has been implemented and has been compared with empirical
correlation which is noted as coupled convective and radiation heat
transfer coefficient. Change in thermal conductivity has been
visualized by analytical model of moving point heat source. Rate of
cooling has been estimated by using 2-dimensional mathematical
expression of cooling rate and it has shown good agreement with
experimental temperature cycle. Thermophysical properties have been
varied randomly within 0 -10s time span.
Abstract: Botnets are one of the most serious and widespread
cyber threats. Today botnets have been facilitating many
cybercrimes, especially financial, top secret thefts. Botnets can be
available for lease in the market and are utilized by the
cybercriminals to launch massive attacks like DDoS, click fraud,
phishing attacks etc., Several large institutions, hospitals, banks,
government organizations and many social networks such as twitter,
facebook etc., became the target of the botmasters. Recently,
noteworthy researches have been carried out to detect bot, C&C
channels, botnet and botmasters. Using many sophisticated
technologies, botmasters made botnet a titan of the cyber world.
Innumerable challenges have been put forth by the botmasters to the
researchers in the detection of botnet. In this paper we present a
survey of different types of botnet C&C channels and also provide a
comparison of various botnet categories. Finally we hope that our
survey will create awareness for forthcoming botnet research
endeavors.
Abstract: Nowadays, the Web has become one of the most
pervasive platforms for information change and retrieval. It collects
the suitable and perfectly fitting information from websites that one
requires. Data mining is the form of extracting data’s available in the
internet. Web mining is one of the elements of data mining
Technique, which relates to various research communities such as
information recovery, folder managing system and simulated
intellects. In this Paper we have discussed the concepts of Web
mining. We contain generally focused on one of the categories of
Web mining, specifically the Web Content Mining and its various
farm duties. The mining tools are imperative to scanning the many
images, text, and HTML documents and then, the result is used by
the various search engines. We conclude by presenting a comparative
table of these tools based on some pertinent criteria.
Abstract: This paper presents a hybrid fuzzy logic control
strategy for a unicycle trajectory following robot on irregular terrains.
In literature, researchers have presented the design of path tracking
controllers of mobile robots on non-frictional surface. In this work,
the robot is simulated to drive on irregular terrains with contrasting
frictional profiles of peat and rough gravel. A hybrid fuzzy logic
controller is utilised to stabilise and drive the robot precisely with the
predefined trajectory and overcome the frictional impact. The
controller gains and scaling factors were optimised using spiral
dynamics optimisation algorithm to minimise the mean square error
of the linear and angular velocities of the unicycle robot. The robot
was simulated on various frictional surfaces and terrains and the
controller was able to stabilise the robot with a superior performance
that is shown via simulation results.
Abstract: Two tragic tsunamis that devastated the west coast of
Sumatra Island, Indonesia in 2004 and North East Japan in 2011 had
damaged bridges to various extents. Tsunamis have resulted in the
catastrophic deterioration of infrastructures i.e. coastal structures,
utilities and transportation facilities. A bridge structure performs vital
roles to enable people to perform activities related to their daily needs
and for development. A damaged bridge needs to be repaired
expeditiously. In order to understand the effects of tsunami forces on
bridges, experimental tests are carried out to measure the
characteristics of hydrodynamic force at various wave heights.
Coastal bridge models designed at a 1:40 scale are used in a 24.0 m
long hydraulic flume with a cross section of 1.5 m by 2.0 m. The
horizontal forces and uplift forces in all cases show that forces
increase nonlinearly with increasing wave amplitude.
Abstract: Marine Protected Areas can benefit from nature based
tourism, monitoring environmental impacts and also become target
for human presence. From more than 3 million tourists visiting
Cozumel Island every year, an average of 2,8 million arrive by cruise
ship, and 41% are estimated to have motivation for water activities.
The destination is relying so much on the tourism activity, that scuba
diving and snorkeling in the National Park Reef of Cozumel sustain
the major economic activity. In order to achieve the sustainable
development indicator designed for regional environmental
development, the PNAC offers a training course to tourism providers
to access the protected area. This way, the update of the last 5 years
of such training is directed to diving staff, boat crew and
professionals, making them able to assist in managing the natural
resource. Moreover, the case study is an example to be used for
raising awareness among tourists visiting protected areas.
Abstract: Asphaltic concrete for pavement construction in India
are produced by using crushed stone, gravels etc. as aggregate. In
north-Eastern region of India, there is a scarcity of stone aggregate.
Therefore the road engineers are always in search of an optional
material as aggregate which can replace the regularly used material.
The purpose of this work was to evaluate the utilization of
substandard or marginal aggregates in flexible pavement
construction. The investigation was undertaken to evaluate the effects
of using lower quality aggregates such as over burnt brick aggregate
on the preparation of asphalt concrete for flexible pavements. The
scope of this work included a review of available literature and
existing data, a laboratory evaluation organized to determine the
effects of marginal aggregates and potential techniques to upgrade
these substandard materials, and a laboratory evaluation of these
upgraded marginal aggregate asphalt mixtures. Over burnt brick
aggregates are water susceptible and can leads to moisture damage.
Moisture damage is the progressive loss of functionality of the
material owing to loss of the adhesion bond between the asphalt
binder and the aggregate surface. Hence zycosoil as an anti striping
additive were evaluated in this study. This study summarizes the
results of the laboratory evaluation carried out to investigate the
properties of asphalt concrete prepared with zycosoil modified over
burnt brick aggregate. Marshall specimen were prepared with stone
aggregate, zycosoil modified stone aggregate, over burnt brick
aggregate and zycosoil modified over burnt brick aggregate. Results
show that addition of zycosoil with stone aggregate increased
stability by 6% and addition of zycosoil with over burnt brick
aggregate increased stability by 30%.
Abstract: The operation of nuclear power plants involves
continuous monitoring of the environment in their area. This
monitoring is performed using a complex data acquisition system,
which collects status information about the system itself and values
of many important physical variables e.g. temperature, humidity,
dose rate etc. This paper describes a proposal and optimization of
communication that takes place in teledosimetric system between the
central control server responsible for the data processing and storing
and the decentralized measuring stations, which are measuring the
physical variables. Analyzes of ongoing communication were
performed and consequently the optimization of the system
architecture and communication was done.
Abstract: Quality control helps industries in improvements of its
product quality and productivity. Statistical Process Control (SPC) is
one of the tools to control the quality of products that turning practice
in bringing a department of industrial engineering process under
control. In this research, the process control of a turning
manufactured at workshops machines. The varying measurements
have been recorded for a number of samples of a rice polished
cylinder obtained from a number of trials with the turning practice.
SPC technique has been adopted by the process is finally brought
under control and process capability is improved.
Abstract: Nanostructured catalysts were successfully prepared
by acidification of diatomite and regeneration of FCC spent catalysts.
The obtained samples were characterized by IR, XRD, SEM, EDX,
MAS-NMR (27Al and 29Si), NH3-TPD and tested in catalytic
pyrolysis of biomass (rice straw). The results showed that the similar
bio-oil yield of 41.4% can be obtained by pyrolysis with catalysts at
450oC as compared to that of the pyrolysis without catalyst at 550oC.
The bio-oil yield reached a maximum of 42.55% at the pyrolysis
temperature of 500oC with catalytic content of 20%. Moreover, by
catalytic pyrolysis, bio-oil quality was better as reflected in higher
ratio of H/C, lower ratio of O/C. This clearly indicated high
application potential of these new nanostructured catalysts in the
production of bio-oil with low oxygenated compounds.
Abstract: This paper evaluates the performance of a multi-lane
four legged modern roundabout operating in Muscat using SIDRA
model. The performance measures include Degree of Saturation
(DOS), average delay, and queue lengths. The geometric and traffic
data were used for model preparation. Gap acceptance parameters,
critical gap and follow up headway, were used for calibration of
SIDRA model. The results from the analysis showed that currently
the roundabout is experiencing delays up to 610 seconds per vehicle
with DOS 1.67 during peak hour. Further, sensitivity analysis for
general and roundabout parameters was performed, amongst lane
width, cruise speed, inscribed diameter, entry radius and entry angle
showed that inscribed diameter is most crucial factor affecting delay
and DOS. Up gradation of roundabout to fully signalized junction
was found as the suitable solution which will serve for future years
with LOS C for design year having DOS of 0.9 with average control
delay of 51.9 seconds per vehicle.
Abstract: The usage of e-health facilities is seen to be the first
priority by the Libyan government. As such this paper focuses on
how the key factors or elements of working size in terms of
technological availability, structural environment, and other
competence-related matters may affect nurses’ sharing of knowledge
in e-health. Hence, this paper investigates learning readiness
assessment to raise e-health for Libyan regional hospitals by using ehealth
services in nursing education.
Abstract: This paper discusses the potential benefits of an
interactive multimedia information representation in enhancing
students’ critical thinking aligned with history reasoning in learning
history amongst Secondary School students in Malaysia. Two modes
of multimedia information representation were implemented;
chronologic and thematic information representations. A qualitative
study of an unstructured interview was conducted among two history
teachers, one history education lecturer, two i-think experts, and five
students from Form Four secondary school. The interview was to
elicit their opinions on the implementation of thinking maps and
interactive multimedia information representation in history learning.
The key elements of the interactive multimedia (e.g. multiple media,
user control, interactivity and use of timelines and concept maps)
were then considered to improve the learning process. Findings of the
preliminary investigation reveal that the interactive multimedia
information representations have the potential benefits to be
implemented as an instructional resource in enhancing students’
higher order thinking skills (HOTs). This paper concludes by giving
suggestions for future work.
Abstract: Essential oils are expensive phytochemicals produced
and extracted from specific species belonging to particular families in
the plant kingdom. In the United Arab Emirates country (UAE), is
located in the arid region of the world, nine species, from the
Lamiaceae family, having the capability to produce therapeutic grade
essential oils. These species include; Mentha spicata, Ocimum
forskolei, Salvia macrosiphon, Salvia aegyptiaca, Salvia macilenta,
Salvia spinosa, Teucrium polium, Teucrium stocksianum and Zataria
multiflora. Although, such potential species are indigenous to the
UAE, however, there are almost no studies available to investigate
the chemical composition and the quality of the extracted essential
oils under the UAE climatological conditions. Therefore, great
attention has to be given to such valuable natural resources, through
conducting highly supported research projects, tailored to the UAE
conditions, and investigating different extraction techniques,
including the application of the latest available technologies, such as
superficial fluid CO2. This is crucially needed; in order to accomplish
the greatest possibilities in the medicinal field, specifically in the
discovery of new therapeutic chemotypes, as well as, to achieve the
sustainability of this natural resource in the country.
Abstract: Two micromechanical models for 3D smart composite
with embedded periodic or nearly periodic network of generally
orthotropic reinforcements and actuators are developed and applied to
cubic structures with unidirectional orientation of constituents.
Analytical formulas for the effective piezothermoelastic coefficients
are derived using the Asymptotic Homogenization Method (AHM).
Finite Element Analysis (FEA) is subsequently developed and used
to examine the aforementioned periodic 3D network reinforced smart
structures. The deformation responses from the FE simulations are
used to extract effective coefficients. The results from both
techniques are compared. This work considers piezoelectric materials
that respond linearly to changes in electric field, electric
displacement, mechanical stress and strain and thermal effects. This
combination of electric fields and thermo-mechanical response in
smart composite structures is characterized by piezoelectric and
thermal expansion coefficients. The problem is represented by unitcell
and the models are developed using the AHM and the FEA to
determine the effective piezoelectric and thermal expansion
coefficients. Each unit cell contains a number of orthotropic
inclusions in the form of structural reinforcements and actuators.
Using matrix representation of the coupled response of the unit cell,
the effective piezoelectric and thermal expansion coefficients are
calculated and compared with results of the asymptotic
homogenization method. A very good agreement is shown between
these two approaches.
Abstract: Musculoskeletal injuries in school children could be
reduced improving trunk strength and hamstring flexibility. Low
levels of trunk muscle strength and hamstring flexibility may result in
acute and musculoskeletal chronic diseases. The Pilates Method can
be appropriate to improve these physical condition attributes and has
been rarely employed by this social group. On the other hand, it has
been shown that trunk strength and flexibility are different between
genders, but there is no evidence about the effect of exercise
programs designed to improve both items in school children.
Therefore the objective of this study was to measure the effect of a
six-week Pilates-based exercise program in 14 year old school
children trunk strength and hamstring flexibility, establishing
differences in gender. The sample was composed of 57 students
divided into experimental group (EG; n=30) and control group (CG;
n=27). Bench Trunk Curl test (BTC), Sörensen test and Toe-touch
test (TT) were used to measure dynamic muscular resistance in trunk
flexion, isometric strength in trunk extension and hamstring
flexibility, respectively. EG utilized the Pilates exercise program
during six-weeks (2 days/week, 55minutes/session). After this period
of training, EG improved trunk strength and hamstring flexibility
significantly but there were no significant differences within CG.
Although boys were better in BTC test and girls were better in TT
test, there were no significant differences between them.