Abstract: In this research a comparison between k-epsilon and
LES model for a deoiling hydrocyclone is conducted. Flow field of
hydrocyclone is obtained by three-dimensional simulations with
OpenFOAM code. Potential of prediction for both methods of this
complex swirl flow is discussed. Large eddy simulation method
results have more similarity to experiment and its results are
presented in figures from different hydrocyclone cross sections.
Abstract: Noise level has critical effects on the diagnostic
performance of signal-averaged electrocardiogram (SAECG), because
the true starting and end points of QRS complex would be masked by
the residual noise and sensitive to the noise level. Several studies and
commercial machines have used a fixed number of heart beats
(typically between 200 to 600 beats) or set a predefined noise level
(typically between 0.3 to 1.0 μV) in each X, Y and Z lead to perform
SAECG analysis. However different criteria or methods used to
perform SAECG would cause the discrepancies of the noise levels
among study subjects. According to the recommendations of 1991
ESC, AHA and ACC Task Force Consensus Document for the use of
SAECG, the determinations of onset and offset are related closely to
the mean and standard deviation of noise sample. Hence this study
would try to perform SAECG using consistent root-mean-square
(RMS) noise levels among study subjects and analyze the noise level
effects on SAECG. This study would also evaluate the differences
between normal subjects and chronic renal failure (CRF) patients in
the time-domain SAECG parameters.
The study subjects were composed of 50 normal Taiwanese and 20
CRF patients. During the signal-averaged processing, different RMS
noise levels were adjusted to evaluate their effects on three time
domain parameters (1) filtered total QRS duration (fQRSD), (2) RMS
voltage of the last QRS 40 ms (RMS40), and (3) duration of the low
amplitude signals below 40 μV (LAS40). The study results
demonstrated that the reduction of RMS noise level can increase
fQRSD and LAS40 and decrease the RMS40, and can further increase
the differences of fQRSD and RMS40 between normal subjects and
CRF patients. The SAECG may also become abnormal due to the
reduction of RMS noise level. In conclusion, it is essential to establish
diagnostic criteria of SAECG using consistent RMS noise levels for
the reduction of the noise level effects.
Abstract: Canola is a specific edible type of rapeseed, developed
in the 1970s, which contains about 40 percent oil. This research was
carried out to determine the yield and some quality characteristics of
some winter canola cultivars during the 2010-2011 vegetation period
in Central Anatolia of Turkey. In this research; Oase, Dante,
Californium, Excalibur, Elvis, ES Hydromel, Licord, Orkan, Vectra,
Nelson, Champlain and NK Petrol winter canola varieties were used
as material. The field experiment was set up in a “Randomized
Complete Block Design” with three replications on 21 September
2010. In this research; seed yield, oil content, protein content, oil
yield and protein yield were examined.
As a result of this research; seed yield, oil content, oil yield and
protein yield (except protein content) were significant differences
between the cultivars. The highest seed yield (6348 kg ha-1) was
obtained from the NK Petrol, while the lowest seed yield (3949 kg
ha-1) was determined from the Champlain cultivar was obtained. The
highest oil content (46.73%) was observed from Oase and the lowest
value was obtained from Vectra (41.87%) cultivar. The highest oil
yield (2950 kg ha-1) was determined from NK Petrol while the least
value (1681 kg ha-1) was determined from Champlain cultivar. The
highest protein yield (1539.3 kg ha-1) was obtained from NK Petrol
and the lowest protein yield (976.5 kg ha-1) was obtained from
Champlain cultivar.
The main purpose of the cultivation of oil crops, to increase the
yield of oil per unit area. According the result of this research, NK
Petrol cultivar which ranks first with regard to both seed yield and oil
yield between cultivars as the most suitable winter canola cultivar of
local conditions.
Abstract: The purpose of this study was to determine the
influence of physical activity and dietary fat intake on Body Mass
Index (BMI) of lecturers within a higher learning institutionalized
setting. The study adopted a Cross-sectional Correlational Design
and included 120 lecturers selected proportionately by simple
random sampling techniques from a population of 600 lecturers. Data
was collected using questionnaires, which had sections including
physical activity checklist adopted from the international physical
activity questionnaire (IPAQ), 24-hour food recall, anthropometric
measurements mainly weight and height. Analysis involved the use
of bivariate correlations and linear regression. A significant inverse
association was registered between BMI and duration (in minutes)
spent doing moderate intense physical activity per day (r=-0.322,
p
Abstract: The influence of extrusion parameters on surface
quality and properties of AA6061+x% vol. SiC (x = 0; 2,5; 5; 7,5;10)
composites was discussed in this paper. The averages size of
AA6061 and SiC particles were 10.6 μm and 0.42 μm, respectively.
Two series of composites (I - compacts were preheated at extrusion
temperature through 0.5 h and cooled by water directly after process;
II - compacts were preheated through 3 hours and were not cooled)
were consolidated via powder metallurgy processing and extruded by
KoBo method. High values of density for both series of composites
were achieved. Better surface quality was observed for II series of
composites. Moreover, for these composites lower (compared to I
series) but more uniform strength properties over the cross-section of
the bar were noticed. Microstructure and Young-s modulus
investigations were made.
Abstract: This paper intends to identify the ethnic Kazakhstani
Koreans- political process of identity formation by exploring their
narrative and practice about the state language represented in the
course of their becoming the new citizens of a new independent state.
The Russophone Kazakhstani Koreans- inability to speak the official
language of their affiliated state is considered there as dissatisfying the
basic requirement of citizens of the independent state, so that they are
becoming marginalized from the public sphere. Their contradictory
attitude that at once demonstrates nominal reception and practical
rejection of the obligatory state language unveils a high barrier inside
between their self-language and other-language. In this paper, the
ethnic Korean group-s conflicting linguistic identity is not seen as a
free and simple choice, but as a dynamic struggle and political process
in which the subject-s past experiences and memories intersect with
the external elements of pressure.
Abstract: This study has investigated a vehicle Lumped
Parameter Model (LPM) in frontal crash. There are several ways for
determining spring and damper characteristics and type of problem
shall be considered as system identification. This study use Genetic
Algorithm (GA) procedure, being an effective procedure in case of
optimization issues, for optimizing errors, between target data
(experimental data) and calculated results (being obtained by
analytical solving). In this study analyzed model in 5-DOF then
compared our results with 5-DOF serial model. Finally, the response
of model due to external excitement is investigated.
Abstract: The response of growth and yield of rainfed-chickpea
to population density should be evaluated based on long-term
experiments to include the climate variability. This is achievable just
by simulation. In this simulation study, this evaluation was done by
running the CYRUS model for long-term daily weather data of five
locations in Iran. The tested population densities were 7 to 59 (with
interval of 2) stands per square meter. Various functions, including
quadratic, segmented, beta, broken linear, and dent-like functions,
were tested. Considering root mean square of deviations and linear
regression statistics [intercept (a), slope (b), and correlation
coefficient (r)] for predicted versus observed variables, the quadratic
and broken linear functions appeared to be appropriate for describing
the changes in biomass and grain yield, and in harvest index,
respectively. Results indicated that in all locations, grain yield tends
to show increasing trend with crowding the population, but
subsequently decreases. This was also true for biomass in five
locations. The harvest index appeared to have plateau state across
low population densities, but decreasing trend with more increasing
density. The turning point (optimum population density) for grain
yield was 30.68 stands per square meter in Isfahan, 30.54 in Shiraz,
31.47 in Kermanshah, 34.85 in Tabriz, and 32.00 in Mashhad. The
optimum population density for biomass ranged from 24.6 (in
Tabriz) to 35.3 stands per square meter (Mashhad). For harvest index
it varied between 35.87 and 40.12 stands per square meter.
Abstract: A preliminary evaluation of the feasibility of installing small wind turbines on offshore oil and gas extraction platforms is presented. Some aerodynamic considerations are developed in order to determine the best rotor architecture to exploit the wind potential on such installations, assuming that wind conditions over the platforms are similar to those registered on the roofs of urban buildings. Economical considerations about both advantages and disadvantages of the exploitation of wind energy on offshore extraction platforms with respect to conventional offshore wind plants, is also presented. Finally, wind charts of European offshore winds are presented together with a map of the major offshore installations.
Abstract: This work presents a low-cost and eco-friendly
building material named Agrostone panel. Africa-s urban population
is growing at an annual rate of 2.8% and 62% of its population will
live in urban areas by 2050. As a consequence, many of the least
urbanized and least developed African countries- will face serious
challenges in providing affordable housing to the urban dwellers.
Since the cost of building materials accounts for the largest
proportion of the overall construction cost, innovating low-cost
building material is vital. Agrostone panel is used in housing projects
in Ethiopia. It uses raw materials of agricultural/industrial wastes
and/or natural minerals as a filler, magnesium-based chemicals as a
binder and fiberglass as reinforcement. Agrostone panel reduces the
cost of wall construction by 50% compared with the conventional
building materials. The pros and cons of Agrostone panel as well as
the use of other waste materials as a raw material to make the panel
more sustainable, low-cost and better properties are discussed.
Abstract: Amazing development of the information technology,
communications and internet expansion as well as the requirements
of the city managers to new ideas to run the city and higher
participation of the citizens encourage us to complete the electronic
city as soon as possible. The foundations of this electronic city are in
information technology. People-s participation in metropolitan
management is a crucial topic. Information technology does not
impede this matter. It can ameliorate populace-s participation and
better interactions between the citizens and the city managers.
Citizens can proffer their ideas, beliefs and votes through digital
mass media based upon the internet and computerization plexuses on
the topical matters to receive appropriate replies and services. They
can participate in urban projects by becoming cognizant of the city
views. The most significant challenges are as follows: information
and communicative management, altering citizens- views, as well as
legal and office documents
Electronic city obstacles have been identified in this research. The
required data were forgathered through questionnaires to identify the
barriers from a statistical community comprising specialists and
practitioners of the ministry of information technology and
communication, the municipality information technology
organization.
The conclusions demonstrate that the prioritized electronic city
application barriers in Iran are as follows:
The support quandaries (non-financial ones), behavioral, cultural
and educational plights, the security, legal and license predicaments,
the hardware, orismological and infrastructural curbs, the software
and fiscal problems.
Abstract: Since the pioneering work of Zadeh, fuzzy set theory has been applied to a myriad of areas. Song and Chissom introduced the concept of fuzzy time series and applied some methods to the enrollments of the University of Alabama. In recent years, a number of techniques have been proposed for forecasting based on fuzzy set theory methods. These methods have either used enrollment numbers or differences of enrollments as the universe of discourse. We propose using the year to year percentage change as the universe of discourse. In this communication, the approach of Jilani, Burney, and Ardil is modified by using the year to year percentage change as the universe of discourse. We use enrollment figures for the University of Alabama to illustrate our proposed method. The proposed method results in better forecasting accuracy than existing models.
Abstract: The paper which is dedicated to describing the effect
made by the “significant other", presents the new model of
interrelation between self-reflection, the “significant other"
phenomenon and aggression. Tendencies of direction and type
frustration response developments in detail are discussed. New
results have been received through designing of the original
experiment. It is based on modifications of the “Picture – Frustration
Study" test by S. Rosenzweig.
Abstract: While financial institutions have faced difficulties
over the years for a multitude of reasons, the major cause of serious
banking problems continues to be directly related to lax credit
standards for borrowers and counterparties, poor portfolio risk
management, or a lack of attention to changes in economic or other
circumstances that can lead to a deterioration in the credit standing of
a bank's counterparties. Credit risk is most simply defined as the
potential that a bank borrower or counterparty will fail to meet its
obligations in accordance with agreed terms. The goal of credit risk
management is to maximize a bank's risk-adjusted rate of return by
maintaining credit risk exposure within acceptable parameters. Banks
need to manage the credit risk inherent in the entire portfolio as well
as the risk in individual credits or transactions. Banks should also
consider the relationships between credit risk and other risks. The
effective management of credit risk is a critical component of a
comprehensive approach to risk management and essential to the
long-term success of any banking organization. In this research we
also study the relationship between credit risk indices and borrower-s
timely payback in Karafarin bank.
Abstract: There is lot of work done in prediction of the fault proneness of the software systems. But, it is the severity of the faults that is more important than number of faults existing in the developed system as the major faults matters most for a developer and those major faults needs immediate attention. In this paper, we tried to predict the level of impact of the existing faults in software systems. Neuro-Fuzzy based predictor models is applied NASA-s public domain defect dataset coded in C programming language. As Correlation-based Feature Selection (CFS) evaluates the worth of a subset of attributes by considering the individual predictive ability of each feature along with the degree of redundancy between them. So, CFS is used for the selecting the best metrics that have highly correlated with level of severity of faults. The results are compared with the prediction results of Logistic Models (LMT) that was earlier quoted as the best technique in [17]. The results are recorded in terms of Accuracy, Mean Absolute Error (MAE) and Root Mean Squared Error (RMSE). The results show that Neuro-fuzzy based model provide a relatively better prediction accuracy as compared to other models and hence, can be used for the modeling of the level of impact of faults in function based systems.
Abstract: The information revealed by derivatives can help to
better characterize digital near-end crosstalk signatures with the
ultimate goal of identifying the specific aggressor signal.
Unfortunately, derivatives tend to be very sensitive to even low
levels of noise. In this work we approximated the derivatives of both
quiet and noisy digital signals using a wavelet-based technique. The
results are presented for Gaussian digital edges, IBIS Model digital
edges, and digital edges in oscilloscope data captured from an actual
printed circuit board. Tradeoffs between accuracy and noise
immunity are presented. The results show that the wavelet technique
can produce first derivative approximations that are accurate to
within 5% or better, even under noisy conditions. The wavelet
technique can be used to calculate the derivative of a digital signal
edge when conventional methods fail.
Abstract: The nature of consumer products causes the difficulty
in forecasting the future demands and the accuracy of the forecasts
significantly affects the overall performance of the supply chain
system. In this study, two data mining methods, artificial neural
network (ANN) and support vector machine (SVM), were utilized to
predict the demand of consumer products. The training data used was
the actual demand of six different products from a consumer product
company in Thailand. The results indicated that SVM had a better
forecast quality (in term of MAPE) than ANN in every category of
products. Moreover, another important finding was the margin
difference of MAPE from these two methods was significantly high
when the data was highly correlated.
Abstract: The breakdown strength characteristic of Low Density
Polyethylene films (LDPE) under DC voltage application and the
effect of water absorption have been studied. Mainly, our experiment
was investigated under two conditions; dry and heavy water
absorption. Under DC ramp voltage, the result found that the
breakdown strength under heavy water absorption has a lower value
than dry condition. In order to clarify the effect, the temperature rise of
film was observed using non contact thermograph until the occurrence
of the electrical breakdown and the conduction current of the sample
was also measured in correlation with the thermograph measurement.
From the observations, it was shown that under the heavy water
absorption, the hot spot in the samples appeared at lower voltage. At
the same voltage the temperature of the hot spot and conduction
current was higher than that under the dry condition. The measurement
result has a good correlation between the existence of a critical field
for conduction current and thermograph observation. In case of the
heavy water absorption, the occurrence of the threshold field was
earlier than the dry condition as result lead to higher of conduction
current and the temperature rise appears after threshold field was
significantly increased in increasing of field. The higher temperature
rise was caused by the higher current conduction as the result the
insulation leads to breakdown to the lower field application.
Abstract: The purposes of this research are: 1) to study the media
literacy of early teenagers, and 2) to study the interaction between
gender and timing of media exposure that affects the media literacy
of teenagers. The sample of the study included 400 young people
aged between 11 to 17 and who were living in Bangkok. The data
was collected using questionnaires. Two-way ANOVA was used in
analyzing the collected data. The result revealed that gender and
timing of media exposure affected the media literacy of early
teenagers with statistical significance at the level of 0.05.
Abstract: Meeting users- requirements is one of predictors of project success. There should be a match between the expectations of the users and the perception of key project personnel with respect to usability and functionality. The aim of this study is to make a comparison of key project personnel-s and potential users- (customer representatives) evaluations of the relative importance of usability and functionality factors in a software design project. Analytical Network Process (ANP) was used to analyze the relative importance of the factors. The results show that navigation and interaction are the most significant factors,andsatisfaction and efficiency are the least important factors for both groups. Further, it can be concluded that having similar orders and scores of usability and functionality factors for both groups shows that key project personnel have captured the expectations and requirements of potential users accurately.