Abstract: Magnesium alloy has been widely investigated as
biodegradable cardiovascular stent and bone implant. Its application
for biodegradable esophageal stenting remains unexplored. This
paper reports the biodegradation behaviors of AZ31 magnesium alloy
in artificial saliva and various types of beverage in vitro. Results
show that the magnesium ion release rate of AZ31 in artificial saliva
for a stent (2cm diameter, 10cm length at 50% stent surface
coverage) is 43 times lower than the daily allowance of human body
magnesium intakes. The degradation rates of AZ31 in different
beverages could also be significantly different. These results suggest
that the esophagus in nature is a less aggressive chemical
environment for degradation of magnesium alloys. The significant
difference in degradation rates of AZ31 in different beverages opens
new opportunities for development of degradation controllable
esophageal stent through customizing ingested beverages.
Abstract: A considerable amount of energy is consumed during
transmission and reception of messages in a wireless mesh network
(WMN). Reducing per-node transmission power would greatly
increase the network lifetime via power conservation in addition to
increasing the network capacity via better spatial bandwidth reuse. In
this work, the problem of topology control in a hybrid WMN of
heterogeneous wireless devices with varying maximum transmission
ranges is considered. A localized distributed topology control
algorithm is presented which calculates the optimal transmission
power so that (1) network connectivity is maintained (2) node
transmission power is reduced to cover only the nearest neighbours
(3) networks lifetime is extended. Simulations and analysis of results
are carried out in the NS-2 environment to demonstrate the
correctness and effectiveness of the proposed algorithm.
Abstract: Gas turbine systems with wet compression have a
potential for future power generation, since they can offer a high
efficiency and a high specific power with a relatively low cost. In this
study influence of ambient condition on the performance of the wet
compression process is investigated with a non-equilibrium analytical
modeling based on droplet evaporation. Transient behaviors of droplet
diameter and temperature of mixed air are investigated for various
ambient temperatures. Special attention is paid for the effects of
ambient temperature, pressure ratio, and water injection ratios on the
important wet compression variables including compressor outlet
temperature and compression work. Parametric studies show that
downing of the ambient temperature leads to lower compressor outlet
temperature and consequently lower consumption of compression
work even in wet compression processes.
Abstract: In this article, models based on quantitative analysis,
physical geometry and regression analysis are established, by using
analytic hierarchy process analysis, fuzzy cluster analysis, fuzzy
photographic and data fitting. The reasons of various leaf shapes
among different species and the differences between the leaf shapes on
same tree have been solved by using software, such as Eviews, VB and
Matlab. We also successfully estimate the leaf mass of a tree and the
correlation with the tree profile.
Abstract: An HPLC-UV analytical method was developed to
determine ethylenediaminetetraacetic acid (EDTA) in dairy
wastewater and surface water. The optimizing separation was achieved
by reversed–phase ion-pair liquid chromatography on a C18 column
using methanol as mobile phase solvent, tetrabutylammonium bromide
as the ion-pair reagent in pH 3.3 formate buffer solution at a flow rate
of 0.9 mL min-1 with a UV detector at 265 nm. No interference of Ca,
Mg or NO3
- was detected. Method performance was evaluated in terms
of linearity, repeatability and reproducibility. The method detection
limit was 5 μg L-1. The contents of EDTA in dairy effluents were 72 ~
261 μg L-1 at a large dairy site. A change of EDTA concentration was
observed downstream of the dairy effluent discharge, but this was well
under the predicted no effect concentration for aquatic ecosystem.
Abstract: A numerical study on the turbulent flow and heat
transfer characteristics in the rectangular channel with different types
of baffles is carried out. The inclined baffles have the width of 19.8
cm, the square diamond type hole having one side length of 2.55 cm,
and the inclination angle of 5o. Reynolds number is varied between
23,000 and 57,000. The SST turbulence model is applied in the
calculation. The validity of the numerical results is examined by the
experimental data. The numerical results of the flow field depict that
the flow patterns around the different baffle type are entirely different
and these significantly affect the local heat transfer characteristics.
The heat transfer and friction factor characteristics are significantly
affected by the perforation density of the baffle plate. It is found that
the heat transfer enhancement of baffle type II (3 hole baffle) has the
best values.
Abstract: In the study of chironomids in Armenia several
species of Orthocladiinae subfamily of Cricotopus genus,
Diamesinae subfamily of Diamesa genus, and Chironominae
subfamily of Chironomus genus, have been identified. In the
Cricotopus genus two sibling species were found, not distinguishable
by larval morphological features, but clearly distinct cytogenetically.
Abstract: In this paper, we propose a new architecture for the implementation of the N-point Fast Fourier Transform (FFT), based on the Radix-2 Decimation in Frequency algorithm. This architecture is based on a pipeline circuit that can process a stream of samples and produce two FFT transform samples every clock cycle. Compared to existing implementations the architecture proposed achieves double processing speed using the same circuit complexity.
Abstract: The study aimed to identify the nature of autistic
talent, the manifestations of their weak central coherence, and their
sensory characteristics. The case study consisted of four talented
autistic males. Two of them in drawing, one in clay formation and
one in jigsaw puzzle. Tools of data collection were Group Embedded
Figures Test, Block Design Test, Sensory Profile Checklist Revised,
Interview forms and direct observation. Results indicated that talent
among autistics emerges in limited domain and being extraordinary
for each case. Also overlapping construction properties. Indeed, they
show three perceptual aspects of weak central coherence: The weak
in visual spatial-constructional coherence, the weak in perceptual
coherence and the weak in verbal – semantic coherence. Moreover,
the majority of the study cases used the three strategies of weak
central coherence (segmentation, obliqueness and rotation). As for
the sensory characteristics, all study cases have numbers of that
characteristics that especially emerges in the visual system.
Abstract: Energy consumption rate during the cooling process
of industrial glass tempering process is considerably high. In this
experimental study the effect of dimensionless jet to jet distance
(S/D) and jet to plate distance (H/D) on the cooling time have been
investigated. In the experiments 4 mm thick glass samples have been
used. Cooling unit consists of 16 mutually placed seamless aluminum
nozzles of 8 mm in diameter and 80 mm in length. Nozzles were in
staggered arrangement. Experiments were conducted with circular
jets for H/D values between 1 and 10, and for S/D values between 2
and 10. During the experiments Reynolds number has been kept
constant at 30000. Experimental results showed that the longest
cooling time with 87 seconds has been observed in the experiments
for S/D=10 and H/D=10 values, while the shortest cooling time with
42.5 seconds has been measured in the experiments for S/D=2 and
H/D=4 values.
Abstract: The current study has investigated the ageing
phenomena of silica optical fibres in relation to water activity which might be accelerated when exposed to a supplementary energy, such as microwaves. A controlled stress by winding fibres onto accurate
diameter mandrel was applied. Taking into account that normally a
decrease in fibre strength is induced in time by chemical action of water, the effects of cumulative reagents such as: water, applied stress and supplementary energy (microwave) in some cases acted in
the opposite manner. The microwave effect as a structural relaxation
catalyst appears unexpected, even if the overall gain in fibre strength is not high, but the stress corrosion factor revealed significant
increase in certain simulation conditions.
Abstract: A reliable estimate of the average bond stress within
the anchorage of steel reinforcing bars in tension is critically
important for the design of reinforced concrete member. This paper
describes part of a recently completed experimental research program
in the Centre for Infrastructure Engineering and Safety (CIES) at the
University of New South Wales, Sydney, Australia aimed at
assessing the effects of different factors on the anchorage
requirements of modern high strength steel reinforcing bars. The
study found that an increase in the anchorage length and bar diameter
generally leads to a reduction of the average ultimate bond stress. By
the extension of a well established analytical model of bond and
anchorage, it is shown here that the differences in the average
ultimate bond stress for different anchorage lengths is associated with
the variable degree of plastic deformation in the tensile zone of the
concrete surrounding the bar.
Abstract: This paper aims to fabricated high quality anodic
aluminum oxide (AAO) film by anodization method. AAO pore size,
pore density, and film thickness can be controlled in 10~500 nm,
108~1011 pore．cm-2, and 1~100 μm. AAO volume and surface area can
be computed based on structural parameters such as thickness, pore
size, pore density, and sample size. Base on the thetorical calculation,
AAO has 100 μm thickness with 15 nm, 60 nm, and 500 nm pore
diameters AAO surface areas are 1225.2 cm2, 3204.4 cm2, and 549.7
cm2, respectively. The large unit surface area which is useful for
adsorption application. When AAO adsorbed pH indictor of
bromphenol blue presented a sensitive pH detection of solution
change. This testing method can further be used for the precise
measurement of biotechnology, convenience measurement of
industrial engineering.
Abstract: Landfill gas, particularly methane is one of the
greenhouse gases which contributes to global warming. This paper presents the findings of a study on methane gas production from
simulated landfill reactor under saturated conditions. A reactor was constructed to represent a landfill cell of 2.5 m thickness on sandy
soil. The reactor was 0.2 m in diameter and 4 m in height. One meter of sand and pebble layer was packed at the bottom of the reactor
followed by 2.5 m of solid waste layer and 0.4 m of sand layer as the cover soil. Degradation of waste in the solid waste layer was at
acidification stage as indicated by the leachate quality with COD as
high as 55,511 mg/L and pH as low as 5.1. However, methanogenic
environment was established at the bottom sand layer after one year of operation indicated by pH of 7.2 and methane gas generation.
Leachate degradation took place as the leachate moved through the
sand layer at an infiltration of rate 0.7 cm/day. This resulted in landfill gas production of 77 mL/day/kg containing 55 to 65% methane. The application of sand layer contributed to the gas
production from landfill by an in-situ degradation of leachate in the
sand at the bottom of the landfill.
Abstract: Wet chemistry methods are used to prepare the
SiO2/Au nanoshells. The purpose of this research was to synthesize
gold coated SiO2 nanoshells for biomedical applications. Tunable
nanoshells were prepared by using different colloidal concentrations.
The nanoshells are characterized by FTIR, XRD, UV-Vis
spectroscopy and atomic force microscopy (AFM). The FTIR results
confirmed the functionalization of the surfaces of silica nanoparticles
with NH2 terminal groups. A tunable absorption was observed
between 470-600 nm with a maximum range of 530-560 nm. Based
on the XRD results three main peaks of Au (111), (200) and (220)
were identified. Also AFM results showed that the silica core
diameter was about 100 nm and the thickness of gold shell about 10
nm.
Abstract: In metal cutting industries, mathematical/statistical
models are typically used to predict tool replacement time. These
off-line methods usually result in less than optimum replacement
time thereby either wasting resources or causing quality problems.
The few online real-time methods proposed use indirect measurement
techniques and are prone to similar errors. Our idea is based on
identifying the optimal replacement time using an electronic nose to
detect the airborne compounds released when the tool wear reaches
to a chemical substrate doped into tool material during the
fabrication. The study investigates the feasibility of the idea, possible
doping materials and methods along with data stream mining
techniques for detection and monitoring different phases of tool
wear.
Abstract: Abdominal aortic aneurysms rupture (AAAs) is one of the main causes of death in the world. This is a very complex phenomenon that usually occurs “without previous warning". Currently, criteria to assess the aneurysm rupture risk (peak diameter and growth rate) can not be considered as reliable indicators. In a first approach, the main geometric parameters of aneurysms have been linked into five biomechanical factors. These are combined to obtain a dimensionless rupture risk index, RI(t), which has been validated preliminarily with a clinical case and others from literature. This quantitative indicator is easy to understand, it allows estimating the aneurysms rupture risks and it is expected to be able to identify the one in aneurysm whose peak diameter is less than the threshold value. Based on initial results, a broader study has begun with twelve patients from the Clinic Hospital of Valladolid-Spain, which are submitted to periodic follow-up examinations.
Abstract: The objective from this paper is to design a solar
thermal engine for space vehicles orbital control and electricity
generation. A computational model is developed for the prediction of
the solar thermal engine performance for different design parameters and conditions in order to enhance the engine efficiency. The engine is divided into two main subsystems. First, the concentrator dish
which receives solar energy from the sun and reflects them to the
cavity receiver. The second one is the cavity receiver which receives
the heat flux reflected from the concentrator and transfers heat to the
fluid passing over. Other subsystems depend on the application required from the engine. For thrust application, a nozzle is
introduced to the system for the fluid to expand and produce thrust.
Hydrogen is preferred as a working fluid in the thruster application.
Results model developed is used to determine the thrust for a
concentrator dish 4 meters in diameter (provides 10 kW of energy),
focusing solar energy to a 10 cm aperture diameter cavity receiver.
The cavity receiver outer length is 50 cm and the internal cavity is 47
cm in length. The suggested design material of the internal cavity is
tungsten to withstand high temperature. The thermal model and
analysis shows that the hydrogen temperature at the plenum reaches
2000oK after about 250 seconds for hot start operation for a flow rate
of 0.1 g/sec.Using solar thermal engine as an electricity generation
device on earth is also discussed. In this case a compressor and
turbine are used to convert the heat gained by the working fluid (air)
into mechanical power. This mechanical power can be converted into
electrical power by using a generator.
Abstract: Heat transfer from two cam shape cylinder in side-byside
arrangement had been studied numerically.
The transverse gap between the centers of cylinders (T) is allowed
to vary to change the pitch ratio (T/Deq). The equivalent diameter of
the cylinder (Deq) is 27.6 mm and pitch ratio varies in range of
1≤T/Deq≤3. The Reynolds numbers based on equivalent circular
cylinder are within 50≤ Reeq≤150. Results show that Nusselt number
of cylinders increases about 1 to 36 percent when pitch ratio
increases from 1 to 3.
Abstract: The study investigated the hydrophilic to hydrophobic
transition of modified polyacrylamide hydrogel with the inclusion of
N-isopropylacrylamide (NIAM). The modification was done by
mimicking micellar polymerization, which resulted in better
arrangement of NIAM chains in the polyacrylamide network. The
degree of NIAM arrangement is described by NH number. The
hydrophilic to hydrophobic transition was measured through the
partition coefficient, K, of Orange II and Methylene Blue in hydrogel
and in water. These dyes were chosen as a model for solutes with
different degree of hydrophobicity. The study showed that the
hydrogel with higher NH values resulted in better solubility of both
dyes. Moreover, in temperature above the lower critical solution
temperature (LCST) of Poly(N-isopropylacrylamide) (PNIAM)also
caused the collapse of NIPAM chains which results in a more
hydrophobic environment that increases the solubility of Methylene
Blue and decreases the solubility of Orange II in the hydrogels with
NIPAM present.