Abstract: Nowadays, illegal logging has been causing many
effects including flash flood, avalanche, global warming, and etc. The
purpose of this study was to maintain the earth ecosystem by keeping
and regulate Malaysia’s treasurable rainforest by utilizing a new
technology that will assist in real-time alert and give faster response
to the authority to act on these illegal activities. The methodology of
this research consisted of design stages that have been conducted as
well as the system model and system architecture of the prototype in
addition to the proposed hardware and software that have been
mainly used such as microcontroller, sensor with the implementation
of GSM, and GPS integrated system. This prototype was deployed at
Royal Belum forest in December 2014 for phase 1 and April 2015 for
phase 2 at 21 pinpoint locations. The findings of this research were
the capture of data in real-time such as temperature, humidity,
gaseous, fire, and rain detection which indicate the current natural
state and habitat in the forest. Besides, this device location can be
detected via GPS of its current location and then transmitted by SMS
via GSM system. All of its readings were sent in real-time for further
analysis. The data that were compared to meteorological department
showed that the precision of this device was about 95% and these
findings proved that the system is acceptable and suitable to be used
in the field.
Abstract: The Greater Athens Area (GAA) faces photochemical
and particulate pollution episodes as a result of the combined effects
of local pollutant emissions, regional pollution transport, synoptic
circulation and topographic characteristics. The area has undergone
significant changes since the Athens 2004 Olympic Games because
of large scale infrastructure works that lead to the shift of population
to areas previously characterized as rural, the increase of the traffic
fleet and the operation of highways. However, few recent modelling
studies have been performed due to the lack of an accurate, updated
emission inventory. The photochemical modelling system
MM5/CAMx was applied in order to study the photochemical and
particulate pollution characteristics above the GAA for two distinct
ten-day periods in the summer of 2006 and 2010, where air pollution
episodes occurred. A new updated emission inventory was used
based on official data. Comparison of modeled results with
measurements revealed the importance and accuracy of the new
Athens emission inventory as compared to previous modeling
studies. The model managed to reproduce the local meteorological
conditions, the daily ozone and particulates fluctuations at different
locations across the GAA. Higher ozone levels were found at
suburban and rural areas as well as over the sea at the south of the
basin. Concerning PM10, high concentrations were computed at the
city centre and the southeastern suburbs in agreement with measured
data. Source apportionment analysis showed that different sources
contribute to the ozone levels, the local sources (traffic, port
activities) affecting its formation.
Abstract: This paper integrates Octagon and Square Search
pattern (OCTSS) motion estimation algorithm into H.264/AVC
(Advanced Video Coding) video codec in Adaptive Group of Pictures
(AGOP) mode. AGOP structure is computed based on scene change
in the video sequence. Octagon and square search pattern block-based
motion estimation method is implemented in inter-prediction process
of H.264/AVC. Both these methods reduce bit rate and computational
complexity while maintaining the quality of the video sequence
respectively. Experiments are conducted for different types of video
sequence. The results substantially proved that the bit rate,
computation time and PSNR gain achieved by the proposed method
is better than the existing H.264/AVC with fixed GOP and AGOP.
With a marginal gain in quality of 0.28dB and average gain in bitrate
of 132.87kbps, the proposed method reduces the average computation
time by 27.31 minutes when compared to the existing state-of-art
H.264/AVC video codec.
Abstract: The present study deals with the characterization of
CrSiN coatings obtained by PVD magnetron sputtering systems.
CrSiN films were deposited with different Si contents, in order to
check the effect of at.% variation on the different properties of the
Cr–N system. Coatings were characterized by scanning electron
microscopy (SEM) for thickness measurements, X-ray diffraction.
Surface morphology and the roughness characteristics were explored
using AFM, Mechanicals properties, elastic and plastic deformation
resistance of thin films were investigated using nanoindentation test. We observed that the Si addition improved the hardness and the
Young’s modulus of the Cr–N system. Indeed, the hardness value is
18,56 GPa for CrSiN coatings. Besides, the Young’s modulus value
is 224,22 GPa for CrSiN coatings for Si content of 1.2 at.%.
Abstract: The present study seeks to investigate the application
of expansion strategy in Persian subtitles of English crime movies.
More precisely, this study aims at classifying the different types of
expansion used in subtitles as well as investigating the
appropriateness or inappropriateness of the application of each type.
To achieve this end, three movies; namely, The Net (1995), Contact
(1997) and Mission Impossible 2 (2000), available with Persian
subtitles, were selected for the study. To collect the data, the above
mentioned movies were watched and those parts of the Persian
subtitles in which expansion had been used were identified and
extracted along with their English dialogs. Then, the extracted
Persian subtitles were classified based on the reason that led to
expansion in each case. Next, the appropriateness or
inappropriateness of using expansion in the extracted Persian
subtitles was descriptively investigated. Finally, an equivalent not
containing any expansion was proposed for those cases in which the
meaning could be fully transferred without this strategy. The findings
of the study indicated that the reasons range from explicitation
(explicitation of visual, co-textual and contextual information),
mistranslation and paraphrasing to the preferences of subtitlers.
Furthermore, it was found that the employment of expansion strategy
was inappropriate in all cases except for those caused by explicitation
of contextual information since correct and shorter equivalents which
were equally capable of conveying the intended meaning could be
posited for the original dialogs.
Abstract: We consider the problem of stabilization of an unstable
heat equation in a 2-D, 3-D and generally n-D domain by deriving a
generalized backstepping boundary control design methodology. To
stabilize the systems, we design boundary backstepping controllers
inspired by the 1-D unstable heat equation stabilization procedure.
We assume that one side of the boundary is hinged and the other
side is controlled for each direction of the domain. Thus, controllers
act on two boundaries for 2-D domain, three boundaries for 3-D
domain and ”n” boundaries for n-D domain. The main idea of the
design is to derive ”n” controllers for each of the dimensions by
using ”n” kernel functions. Thus, we obtain ”n” controllers for the
”n” dimensional case. We use a transformation to change the system
into an exponentially stable ”n” dimensional heat equation. The
transformation used in this paper is a generalized Volterra/Fredholm
type with ”n” kernel functions for n-D domain instead of the one
kernel function of 1-D design.
Abstract: In the context of the handwriting recognition, we
propose an off line system for the recognition of the Arabic
handwritten words of the Algerian departments. The study is based
mainly on the evaluation of neural network performances, trained
with the gradient back propagation algorithm. The used parameters to
form the input vector of the neural network are extracted on the
binary images of the handwritten word by several methods. The
Distribution parameters, the centered moments of the different
projections of the different segments, the centered moments of the
word image coding according to the directions of Freeman, and the
Barr features applied binary image of the word and on its different
segments. The classification is achieved by a multi layers perceptron.
A detailed experiment is carried and satisfactory recognition results
are reported.
Abstract: It is well-known that, using principal weak flatness
property, some important monoids are characterized, such as regular
monoids, left almost regular monoids, and so on. In this article, we
define a generalization of principal weak flatness called GP-Flatness,
and will characterize monoids by this property of their right (Rees
factor) acts. Also we investigate new classes of monoids called
generally regular monoids and generally left almost regular monoids.
Abstract: In this paper, we present an optimization technique or
a learning algorithm using the hybrid architecture by combining the
most popular sequence recognition models such as Recurrent Neural
Networks (RNNs) and Hidden Markov models (HMMs). In order to
improve the sequence/pattern recognition/classification performance
by applying a hybrid/neural symbolic approach, a gradient descent
learning algorithm is developed using the Real Time Recurrent
Learning of Recurrent Neural Network for processing the knowledge
represented in trained Hidden Markov Models. The developed hybrid
algorithm is implemented on automata theory as a sample test beds
and the performance of the designed algorithm is demonstrated and
evaluated on learning the deterministic finite state automata.
Abstract: This article presents the main results of a numerical
investigation on the uncertainty of dynamic response of structures
with statistically correlated random damping Gamma distributed. A
computational method based on a Linear Statistical Model (LSM) is
implemented to predict second order statistics for the response of a
typical industrial building structure. The significance of random
damping with correlated parameters and its implications on the
sensitivity of structural peak response in the neighborhood of a
resonant frequency are discussed in light of considerable ranges of
damping uncertainties and correlation coefficients. The results are
compared to those generated using Monte Carlo simulation
techniques. The numerical results obtained show the importance of
damping uncertainty and statistical correlation of damping
coefficients when obtaining accurate probabilistic estimates of
dynamic response of structures. Furthermore, the effectiveness of the
LSM model to efficiently predict uncertainty propagation for
structural dynamic problems with correlated damping parameters is
demonstrated.
Abstract: The present study focused on the investigation of the
effects of roughness elements on heat transfer during natural
convection in a rectangular cavity using numerical technique.
Roughness elements were introduced on the bottom hot wall with a
normalized amplitude (A*/H) of 0.1. Thermal and hydrodynamic
behaviors were studied using computational method based on Lattice
Boltzmann method (LBM). Numerical studies were performed for a
laminar flow in the range of Rayleigh number (Ra) from 103 to 106
for a rectangular cavity of aspect ratio (L/H) 2.0 with a fluid of
Prandtl number (Pr) 1.0. The presence of the sinusoidal roughness
elements caused a minimum to maximum decrease in the heat
transfer as 7% to 17% respectively compared to smooth enclosure.
The results are presented for mean Nusselt number (Nu), isotherms
and streamlines.
Abstract: The study conducted a simulation of the effect of sea
water to the bonding capacity of GFRP sheet on the concrete beams
using a simulation tank. Fiber reinforced polymer (FRP) has been
developed and applied in many fields civil engineering structures on
the new structures and also for strengthening of the deteriorated
structures. The FRP has advantages such as its corrosion resistance as
well as high tensile strength to weight ratio. Compared to the other
FRP materials, Glass composed FRP (GFRP) is relatively cheaper.
GFRP sheet is applied externally by bonding it on the concrete surface.
The studies regarding the application of GFRP sheet have been
conducted such as strengthening system, bonding behavior of GFRP
sheet including the application as reinforcement in new structures. For
application to the structures with direct contact to sea environment, a
study regarding the effect of sea water to the bonding capacity of
GFRP sheet is important to be clarified. To achieve the objective of the
study, a series of concrete beams strengthened with GFRP sheet on
extreme tension surface were prepared. The beams then were stored on
the sea water tank for six months. Results indicated the bonding
capacity decreased after six month exposed to the sea water.
Abstract: Modelling of building processes of a multimodal
freight transportation support information system is discussed based
on modern CASE technologies. Functional efficiencies of ports in
the eastern part of the Black Sea are analyzed taking into account
their ecological, seasonal, resource usage parameters. By resources,
we mean capacities of berths, cranes, automotive transport, as well as
work crews and neighbouring airports. For the purpose of designing
database of computer support system for Managerial (Logistics)
function, using Object-Role Modeling (ORM) tool (NORMA–Natural ORM Architecture) is proposed, after which Entity
Relationship Model (ERM) is generated in automated process.
Software is developed based on Process-Oriented and Service-Oriented architecture, in Visual Studio.NET environment.
Abstract: In the last decade the emergence of new social needs
as an effect of the economic crisis has stimulated the flourishing of
business endeavours characterised by explicit social goals. Social
start-ups, social enterprises or Corporate Social Responsibility
operations carried out by traditional companies are quintessential
examples in this regard. This paper analyses these kinds of initiatives
in order to discover the main characteristics of social business models
and to provide insights to social entrepreneurs for developing or
improving their strategies. The research is conducted through the
integration of literature review and case study analysis and, thanks to
the recognition of the importance of both profits and social impacts
as the key success factors for a social business model, proposes a
framework for identifying indicators suitable for measuring the social
impacts generated.
Abstract: The Green Urban Lab took the form of public
installations that were placed at various locations in four cities in
Cyprus. These installations - through which a series of events,
activities, workshops and research took place - were the main tools in
regenerating a series of urban public spaces in Cyprus. The purpose
of this project was to identify issues and opportunities related to
public space and to offer guidelines on how design and participatory
democracy improvements could strengthen civil society, while
raising the quality of the urban public scene. Giant inflatable
structures were injected in important urban fragments in order to
accommodate series of events. The design and playful installation
generated a wide community engagement. The fluid presence of the
installations acted as a catalyst for social interaction. They were
accessed and viewed effortlessly and surprisingly, creating
opportunities to rediscover public spaces.
Abstract: Carbon Fiber Reinforced Plastics (CFRPs) are widely
used for advanced applications, in particular in aerospace, automotive
and wind energy industries. Once cured to near net shape, CFRP
parts need several finishing operations such as trimming, milling or
drilling in order to accommodate fastening hardware and meeting the
final dimensions. The present research aims to study the effect of the
cutting temperature in trimming on the mechanical strength of high
performance CFRP laminates used for aeronautics applications. The
cutting temperature is of great importance when dealing with
trimming of CFRP. Temperatures higher than the glass-transition
temperature (Tg) of the resin matrix are highly undesirable: they
cause degradation of the matrix in the trimmed edges area, which can
severely affect the mechanical performance of the entire component.
In this study, a 9.50mm diameter CVD diamond coated carbide tool
with six flutes was used to trim 24-plies CFRP laminates. A
300m/min cutting speed and 1140mm/min feed rate were used in the
experiments. The tool was heated prior to trimming using a
blowtorch, for temperatures ranging from 20°C to 300°C. The
temperature at the cutting edge was measured using embedded KType
thermocouples. Samples trimmed for different cutting
temperatures, below and above Tg, were mechanically tested using
three-points bending short-beam loading configurations. New cutting
tools as well as worn cutting tools were utilized for the experiments.
The experiments with the new tools could not prove any correlation
between the length of cut, the cutting temperature and the mechanical
performance. Thus mechanical strength was constant, regardless of
the cutting temperature. However, for worn tools, producing a cutting
temperature rising up to 450°C, thermal damage of the resin was
observed. The mechanical tests showed a reduced mean resistance in
short beam configuration, while the resistance in three point bending
decreases with increase of the cutting temperature.
Abstract: Rapid prototyping is a new group of manufacturing
processes, which allows fabrication of physical of any complexity
using a layer by layer deposition technique directly from a computer
system. The rapid prototyping process greatly reduces the time and
cost necessary to bring a new product to market. The prototypes
made by these systems are used in a range of industrial application
including design evaluation, verification, testing, and as patterns for
casting processes. These processes employ a variety of materials and
mechanisms to build up the layers to build the part. The present work
was to build a FDM prototyping machine that could control the X-Y
motion and material deposition, to generate two-dimensional and
three-dimensional complex shapes. This study focused on the
deposition of wax material. This work was to find out the properties
of the wax materials used in this work in order to enable better
control of the FDM process. This study will look at the integration of
a computer controlled electro-mechanical system with the traditional
FDM additive prototyping process. The characteristics of the wax
were also analysed in order to optimise the model production process.
These included wax phase change temperature, wax viscosity and
wax droplet shape during processing.
Abstract: The ferrites ZnFe2O4, CdFe2O4 and CuFe2O4 are
synthesized in laboratory conditions using ceramic technology. Their
homogeneity and structure are proven by X-Ray diffraction analysis
and Mössbauer spectroscopy. The synthesized ferrites are subjected
to strong acid and high temperature leaching with solutions of H2SO4,
HCl and HNO3. The results indicate that the highest degree of
leaching of Zn, Cd and Cu from the ferrites is achieved by use of
HCl. The charging of five zinc sulfide concentrates was optimized using
the criterion of minimal amount of zinc ferrite produced when
roasting the concentrates in a fluidized bed. The results obtained are
interpreted in terms of the hydrometallurgical zinc production and
maximum recovery of zinc, copper and cadmium from initial zinc
concentrates after their roasting.
Abstract: The activation volume of 6082T6 aluminum is
investigated at different temperatures for grain size variants. The
deformation activation volume was computed on the basis of the
relationship between the Boltzmann’s constant k, the testing
temperatures, the material strain rate sensitivity and the material yield
stress grain size variants. The material strain rate sensitivity is
computed as a function of yield stress and strain rate grain size
variants. The effect of the material strain rate sensitivity and the
deformation activation volume of 6082T6 aluminum at different
temperatures of 3-D grain are discussed. It is shown that the strain rate sensitivities and activation volume
are negative for the grain size variants during the deformation of
nanostructured materials. It is also observed that the activation
volume vary in different ways with the equivalent radius, semi minor
axis radius, semi major axis radius and major axis radius. From the
obtained results it is shown that the variation of activation volume
increase and decrease with the testing temperature. It was revealed
that, increase in strain rate sensitivity led to decrease in activation
volume whereas increase in activation volume led to decrease in
strain rate sensitivity.
Abstract: The aim of optimization of store management is not
only designing the situation of store management itself including its
equipment, technology and operation. In optimization of store
management we need to consider also synchronizing of
technological, transport, store and service operations throughout the
whole process of logistic chain in such a way that a natural flow of
material from provider to consumer will be achieved the shortest
possible way, in the shortest possible time in requested quality and
quantity and with minimum costs. The paper deals with the
application of the queuing theory for optimization of warehouse
processes. The first part refers to common information about the
problematic of warehousing and using mathematical methods for
logistics chains optimization. The second part refers to preparing a
model of a warehouse within queuing theory. The conclusion of the
paper includes two examples of using queuing theory in praxis.