Abstract: One of the major cause of eye strain and other
problems caused while watching television is the relative illumination between the screen and its surrounding. This can be
overcome by adjusting the brightness of the screen with respect to the surrounding light. A controller based on fuzzy logic is proposed
in this paper. The fuzzy controller takes in the intensity of light
surrounding the screen and the present brightness of the screen as input. The output of the fuzzy controller is the grid voltage corresponding to the required brightness. This voltage is given to CRT and brightness is controller dynamically. For the given test system data, different de-fuzzifier methods have been implemented and the results are compared. In order to validate the effectiveness of
the proposed approach, a fuzzy controller has been designed by obtaining a test data from a real time system. The simulations are
performed in MATLAB and are verified with standard system data. The proposed approach can be implemented for real time
applications.
Abstract: Over the past few years, a number of efforts have
been exerted to build parallel processing systems that utilize the idle
power of LAN-s and PC-s available in many homes and corporations.
The main advantage of these approaches is that they provide cheap
parallel processing environments for those who cannot afford the
expenses of supercomputers and parallel processing hardware.
However, most of the solutions provided are not very flexible in the
use of available resources and very difficult to install and setup.
In this paper, a multi-level web-based parallel processing system
(MWPS) is designed (appendix). MWPS is based on the idea of
volunteer computing, very flexible, easy to setup and easy to use.
MWPS allows three types of subscribers: simple volunteers (single
computers), super volunteers (full networks) and end users. All of
these entities are coordinated transparently through a secure web site.
Volunteer nodes provide the required processing power needed by
the system end users. There is no limit on the number of volunteer
nodes, and accordingly the system can grow indefinitely. Both
volunteer and system users must register and subscribe. Once, they
subscribe, each entity is provided with the appropriate MWPS
components. These components are very easy to install.
Super volunteer nodes are provided with special components that
make it possible to delegate some of the load to their inner nodes.
These inner nodes may also delegate some of the load to some other
lower level inner nodes .... and so on. It is the responsibility of the
parent super nodes to coordinate the delegation process and deliver
the results back to the user.
MWPS uses a simple behavior-based scheduler that takes into
consideration the current load and previous behavior of processing
nodes. Nodes that fulfill their contracts within the expected time get a
high degree of trust. Nodes that fail to satisfy their contract get a
lower degree of trust.
MWPS is based on the .NET framework and provides the minimal
level of security expected in distributed processing environments.
Users and processing nodes are fully authenticated. Communications
and messages between nodes are very secure. The system has been
implemented using C#.
MWPS may be used by any group of people or companies to
establish a parallel processing or grid environment.
Abstract: The latest Geographic Information System (GIS)
technology makes it possible to administer the spatial components of
daily “business object," in the corporate database, and apply suitable
geographic analysis efficiently in a desktop-focused application. We
can use wireless internet technology for transfer process in spatial
data from server to client or vice versa. However, the problem in
wireless Internet is system bottlenecks that can make the process of
transferring data not efficient. The reason is large amount of spatial
data. Optimization in the process of transferring and retrieving data,
however, is an essential issue that must be considered. Appropriate
decision to choose between R-tree and Quadtree spatial data indexing
method can optimize the process. With the rapid proliferation of
these databases in the past decade, extensive research has been
conducted on the design of efficient data structures to enable fast
spatial searching. Commercial database vendors like Oracle have also
started implementing these spatial indexing to cater to the large and
diverse GIS. This paper focuses on the decisions to choose R-tree
and quadtree spatial indexing using Oracle spatial database in mobile
GIS application. From our research condition, the result of using
Quadtree and R-tree spatial data indexing method in one single
spatial database can save the time until 42.5%.
Abstract: This paper presents a pulse doubling technique in a 12-pulse ac-dc converter which supplies direct torque controlled motor drives (DTCIMD-s) in order to have better power quality conditions at the point of common coupling. The proposed technique increases the number of rectification pulses without significant changes in the installations and yields in harmonic reduction in both ac and dc sides. The 12-pulse rectified output voltage is accomplished via two paralleled six-pulse ac-dc converters each of them consisting of three-phase diode bridge rectifier. An autotransformer is designed to supply the rectifiers. The design procedure of magnetics is in a way such that makes it suitable for retrofit applications where a six-pulse diode bridge rectifier is being utilized. Independent operation of paralleled diode-bridge rectifiers, i.e. dc-ripple re-injection methodology, requires a Zero Sequence Blocking Transformer (ZSBT). Finally, a tapped interphase reactor is connected at the output of ZSBT to double the pulse numbers of output voltage up to 24 pulses. The aforementioned structure improves power quality criteria at ac mains and makes them consistent with the IEEE-519 standard requirements for varying loads. Furthermore, near unity power factor is obtained for a wide range of DTCIMD operation. A comparison is made between 6- pulse, 12-pulse, and proposed converters from view point of power quality indices. Results show that input current total harmonic distortion (THD) is less than 5% for the proposed topology at various loads.
Abstract: The focus of the study is to understand the factors of
curriculum innovation from the perspective of Language teacher
education. The overall aim of the study is to investigate Language
educators- perceptions of factors of curriculum innovation. In the
theoretical framework the main focus is on discussion about different
curriculum approaches for language teacher education and limiting
and facilitating factors of innovation. In order to achieve the aim of
the study, an observational research is employed. The empirical basis
of the study consists of questionnaire with sixty-three language
teachers from eight Romanian higher education institutions. The
findings reveal variation in Language teachers- conceptions of the
dominant factors of curricular innovation.
Abstract: The evolutionary design of electronic circuits, or
evolvable hardware, is a discipline that allows the user to
automatically obtain the desired circuit design. The circuit
configuration is under the control of evolutionary algorithms. Several
researchers have used evolvable hardware to design electrical
circuits. Every time that one particular algorithm is selected to carry
out the evolution, it is necessary that all its parameters, such as
mutation rate, population size, selection mechanisms etc. are tuned in
order to achieve the best results during the evolution process. This
paper investigates the abilities of evolution strategy to evolve digital
logic circuits based on programmable logic array structures when
different mutation rates are used. Several mutation rates (fixed and
variable) are analyzed and compared with each other to outline the
most appropriate choice to be used during the evolution of
combinational logic circuits. The experimental results outlined in this
paper are important as they could be used by every researcher who
might need to use the evolutionary algorithm to design digital logic
circuits.
Abstract: Dioscorea species or commonly named as yam is
reported to be one of the major food sources worldwide. This
ethnobotanical study was conducted to document local knowledge
and potentials of DioscoreahispidaDennst. and to investigate and
record its distribution in three districts of Terengganu. Information
was gathered from 23 villagers from three districts of Besut, Marang
and Setiu by using semi-structured questionnaire. The villagers were
randomly selected and no appointment was made prior to the visits.
For distribution, the location of Dioscoreahispida was recorded by
using the Global Positioning System (GPS). The villagers identified
Dioscoreahispida or locally named ubigadong by looking at the
physical characteristics that include its leaf shape, stem and the color
of the tuber-s flesh. The villagers used Dioscoreahispida in many
ways in their life such as for food, medicinal purposes and fish
poison.
Abstract: Various intelligences and inspirations have been
adopted into the iterative searching process called as meta-heuristics.
They intelligently perform the exploration and exploitation in the
solution domain space aiming to efficiently seek near optimal
solutions. In this work, the bee algorithm, inspired by the natural
foraging behaviour of honey bees, was adapted to find the near
optimal solutions of the transportation management system, dynamic
multi-zone dispatching. This problem prepares for an uncertainty and
changing customers- demand. In striving to remain competitive,
transportation system should therefore be flexible in order to cope
with the changes of customers- demand in terms of in-bound and outbound
goods and technological innovations. To remain higher service
level but lower cost management via the minimal imbalance scenario,
the rearrangement penalty of the area, in each zone, including time
periods are also included. However, the performance of the algorithm
depends on the appropriate parameters- setting and need to be
determined and analysed before its implementation. BEE parameters
are determined through the linear constrained response surface
optimisation or LCRSOM and weighted centroid modified simplex
methods or WCMSM. Experimental results were analysed in terms
of best solutions found so far, mean and standard deviation on the
imbalance values including the convergence of the solutions
obtained. It was found that the results obtained from the LCRSOM
were better than those using the WCMSM. However, the average
execution time of experimental run using the LCRSOM was longer
than those using the WCMSM. Finally a recommendation of proper
level settings of BEE parameters for some selected problem sizes is
given as a guideline for future applications.
Abstract: A novel three-phase active power filter (APF) circuit with photovoltaic (PV) system to improve the quality of service and to reduce the capacity of energy storage capacitor is presented. The energy balance concept and sampling technique were used to simplify the calculation algorithm for the required utility source current and to control the voltage of the energy storage capacitor. The feasibility was verified by using the Pspice simulations and experiments. When the APF mode was used during non-operational period, not only the utilization rate, power factor and power quality could be improved, but also the capacity of energy storage capacitor could sparing. As the results, the advantages of the APF circuit are simplicity of control circuits, low cost, and good transient response.
Abstract: Virtual engineering technology has undergone rapid progress in recent years and is being adopted increasingly by manufacturing companies of many engineering disciplines. There is an increasing demand from industry for qualified virtual engineers. The qualified virtual engineers should have the ability of applying engineering principles and mechanical design methods within the commercial software package environment. It is a challenge to the engineering education in universities which traditionally tends to lack the integration of knowledge and skills required for solving real world problems. In this paper, a case study shows some recent development of a MSc Mechanical Engineering course at Department of Engineering and Technology in MMU, and in particular, two units Simulation of Mechanical Systems(SMS) and Computer Aided Fatigue Analysis(CAFA) that emphasize virtual engineering education and promote integration of knowledge acquisition, skill training and industrial application.
Abstract: In this paper we study different similarity based approaches for the development of QSAR model devoted to the prediction of activity of antiobesity drugs. Classical similarity approaches are compared regarding to dissimilarity models based on the consideration of the calculation of Euclidean distances between the nonisomorphic fragments extracted in the matching process. Combining the classical similarity and dissimilarity approaches into a new similarity measure, the Approximate Similarity was also studied, and better results were obtained. The application of the proposed method to the development of quantitative structure-activity relationships (QSAR) has provided reliable tools for predicting of inhibitory activity of drugs. Acceptable results were obtained for the models presented here.
Abstract: Nosocomial (i.e., hospital-acquired) infections
(NI) is a major cause of morbidity and mortality in hospitals. NI
rate is higher in intensive care units (ICU) than in the general
ward due to patients with severe symptoms, poor immunity,
and accepted many invasive therapies. Contact behaviors
between health caregivers and patients is one of the infect
factors. It is difficult to obtain complete contact records by
traditional method of retrospective analysis of medical records.
This paper establishes a contact history inferential model
(CHIM) intended to extend the use of Proximity Sensing of
rapid frequency identification (RFID) technology to
transferring all proximity events between health caregivers and
patients into clinical events (close-in events, contact events and
invasive events).The results of the study indicated that the
CHIM can infer proximity care activities into close-in events
and contact events.
The infection control team could redesign and build optimal
workflow in the ICU according to the patient-specific contact
history which provided by our automatic tracing system.
Abstract: The influence of physical (external added weight) and
neurophysiological (fatigue) factors on static and dynamic balance in
sport related activities was typified statically by the Romberg test
(one foot flat, eyes open) and dynamically by jumping and hopping
in both horizontal and vertical directions. Twenty healthy males were
participated in this study. In Static condition, added weight increased
body-s inertia and therefore decreased body sway in AP direction
though not significantly. Dynamically, added weight significantly
increased body sway in both ML and AP directions, indicating
instability, and the use of the counter rotating segments mechanism to
maintain balance was demonstrated. Fatigue on the other hand
significantly increased body sway during static balance as a
neurophysiological adaptation primarily to the inverted pendulum
mechanism. Dynamically, fatigue significantly increased body sway
in both ML and AP directions again indicating instability but with a
greater use of counter rotating segments mechanism. Differential
adaptations for each of the two balance mechanisms (inverted
pendulum and counter rotating segments) were found between one
foot flat and two feet flat dynamic conditions, as participants relied
more heavily on the first in the one foot flat conditions and relied
more on the second in the two feet flat conditions.
Abstract: This paper presents a speed sensorless direct torque
control scheme using space vector modulation (DTC-SVM) for
permanent magnet synchronous motor (PMSM) drive based a Model
Reference Adaptive System (MRAS) algorithm and stator resistance
estimator. The MRAS is utilized to estimate speed and stator
resistance and compensate the effects of parameter variation on stator
resistance, which makes flux and torque estimation more accurate
and insensitive to parameter variation. In other hand the use of SVM
method reduces the torque ripple while achieving a good dynamic
response. Simulation results are presented and show the effectiveness
of the proposed method.
Abstract: Study of the vibration cylindrical shells made of
a functionally gradient material (FGM) composed of stainless
steel and nickel is important. Material properties are graded in
the thickness direction of the shell according to volume
fraction power law distribution. The objective is to study the
natural frequencies, the influence of constituent volume
fractions and the effects of boundary conditions on the natural
frequencies of the FG cylindrical shell. The study is carried
out using third order shear deformation shell theory. The
governing equations of motion of FG cylindrical shells are
derived based on shear deformation theory. Results are
presented on the frequency characteristics, influence of
constituent volume fractions and the effects of clampedclamped
boundary conditions.
Abstract: There are many expand of Wi-Fi zones provided
mobile careers and usage of wireless access point at home as increase
of usage of wireless internet caused by the use of smart phone. This
paper shows wireless local area network status, security threats of
WLAN and functionality of major wireless access point in Korea. We
propose security countermeasures concerned with life cycle of access
point from manufacturing to installation, using and finally disposal.
There needed to releasing with configured secure at access point.
Because, it is most cost effective resolution than stage of installation or
other life cycle of access point.
Abstract: In this paper, based on the work in [1], we further give
a general model for acquiring knowledge, which first focuses on the
research of how and when things involved in problems are made
then describes the goals, the energy and the time to give an optimum
model to decide how many related things are supposed to be involved
in. Finally, we acquire knowledge from this model in which there are
the attributes, actions and connections of the things involved at the
time when they are born and the time in their life. This model not
only improves AI theories, but also surely brings the effectiveness
and accuracy for AI system because systems are given more
knowledge when reasoning or computing is used to bring about
results.
Abstract: This paper presents a review on vision aided systems
and proposes an approach for visual rehabilitation using stereo vision
technology. The proposed system utilizes stereo vision, image
processing methodology and a sonification procedure to support
blind navigation. The developed system includes a wearable
computer, stereo cameras as vision sensor and stereo earphones, all
moulded in a helmet. The image of the scene infront of visually
handicapped is captured by the vision sensors. The captured images
are processed to enhance the important features in the scene in front,
for navigation assistance. The image processing is designed as model
of human vision by identifying the obstacles and their depth
information. The processed image is mapped on to musical stereo
sound for the blind-s understanding of the scene infront. The
developed method has been tested in the indoor and outdoor
environments and the proposed image processing methodology is
found to be effective for object identification.
Abstract: The Ant Colony Optimization (ACO) is a metaheuristic inspired by the behavior of real ants in their search for the shortest paths to food sources. It has recently attracted a lot of attention and has been successfully applied to a number of different optimization problems. Due to the importance of the feature selection problem and the potential of ACO, this paper presents a novel method that utilizes the ACO algorithm to implement a feature subset search procedure. Initial results obtained using the classification of speech segments are very promising.
Abstract: Water pipe network is installed underground and once equipped, it is difficult to recognize the state of pipes when the leak or burst happens. Accordingly, post management is often delayed
after the fault occurs. Therefore, the systematic fault management system of water pipe network is required to prevent the accident and
minimize the loss. In this work, we develop online fault detection system of water pipe network using data of pipes such as flow rate
or pressure. The transient model describing water flow in pipelines
is presented and simulated using MATLAB. The fault situations such
as the leak or burst can be also simulated and flow rate or pressure data when the fault happens are collected. Faults are detected using
statistical methods of fast Fourier transform and discrete wavelet transform, and they are compared to find which method shows the
better fault detection performance.