Abstract: At-site flood frequency analysis is used to estimate
flood quantiles when at-site record length is reasonably long. In
Australia, FLIKE software has been introduced for at-site flood
frequency analysis. The advantage of FLIKE is that, for a given
application, the user can compare a number of most commonly
adopted probability distributions and parameter estimation methods
relatively quickly using a windows interface. The new version of
FLIKE has been incorporated with the multiple Grubbs and Beck test
which can identify multiple numbers of potentially influential low
flows. This paper presents a case study considering six catchments in
eastern Australia which compares two outlier identification tests
(original Grubbs and Beck test and multiple Grubbs and Beck test)
and two commonly applied probability distributions (Generalized
Extreme Value (GEV) and Log Pearson type 3 (LP3)) using FLIKE
software. It has been found that the multiple Grubbs and Beck test
when used with LP3 distribution provides more accurate flood
quantile estimates than when LP3 distribution is used with the
original Grubbs and Beck test. Between these two methods, the
differences in flood quantile estimates have been found to be up to
61% for the six study catchments. It has also been found that GEV
distribution (with L moments) and LP3 distribution with the multiple
Grubbs and Beck test provide quite similar results in most of the
cases; however, a difference up to 38% has been noted for flood
quantiles for annual exceedance probability (AEP) of 1 in 100 for one
catchment. This finding needs to be confirmed with a greater number
of stations across other Australian states.
Abstract: An investigation into the effect of countersunk depth,
plate thickness, countersunk angle and plate width on the stress
concentration around countersunk hole is carried out with the help of
finite element analysis. The variation of stress concentration with
respect to these parameters is studied for three types of loading viz.
uniformly distributed load, uniformly varying load and functionally
distributed load. The results of the finite element analysis are
interpreted and some conclusions are drawn. The distribution of
stress concentration around countersunk hole in isotropic plates
simply supported at all the edges is found similar and is independent
of loading. The maximum stress concentration also occurs at a
particular point irrespective of the loading conditions.
Abstract: Present study is aimed on the cutting process of circular
cross-section rods where the fracture is used to separate one rod
into two pieces. Incorporating the phenomenological ductile fracture
model into the explicit formulation of finite element method, the
process can be analyzed without the necessity of realizing too many
real experiments which could be expensive in case of repetitive
testing in different conditions. In the present paper, the steel AISI
1045 was examined and the tensile tests of smooth and notched
cylindrical bars were conducted together with biaxial testing of the
notched tube specimens to calibrate material constants of selected
phenomenological ductile fracture models. These were implemented
into the Abaqus/Explicit through user subroutine VUMAT and used
for cutting process simulation. As the calibration process is based
on variables which cannot be obtained directly from experiments,
numerical simulations of fracture tests are inevitable part of the
calibration. Finally, experiments regarding the cutting process were
carried out and predictive capability of selected fracture models is
discussed. Concluding remarks then make the summary of gained
experience both with the calibration and application of particular
ductile fracture criteria.
Abstract: Self-service technologies (SSTs) make an important
contribution to the daily life of people nowadays. However, the
introduction of SST does not lead to its usage. Thereby, this paper
was an attempt on discovery of the most preferred SST in the
customers’ point of view. To fulfill this aim, the Analytical Hierarchy
Process (AHP) was applied based on Saaty’s questionnaire which
was administered to the customers of e-banking services located in
Golestan providence, northern Iran. This study used qualitative
factors in association with the intention of consumers’ usage of SSTs
to rank three SSTs: ATM, mobile banking and internet banking. The
results showed that mobile banking get the highest weight in
consumers’ point of view. This research can be useful both for
managers and service providers and also for customers who intend to
use e-banking.
Abstract: In the present work, the finite element formulation for
the investigation of the effects of a localized interfacial degeneration
on the dynamic behavior of the [90°/0°] laminated composite plate
employing the state-space technique is performed. The stiffness of
the laminate is determined by assembling the stiffnesses of subelements.
This includes an introduction of an interface layer adopting
the virtually zero-thickness formulation to model the interfacial
degeneration. Also, the kinematically consistent mass matrix and
proportional damping have been formulated to complete the free
vibration governing expression. To simulate the interfacial
degeneration of the laminate, the degenerated areas are defined from
the center propagating outwards in a localized manner. It is found
that the natural frequency, damped frequency and damping ratio of
the plate decreases as the degenerated area of the interface increases.
On the contrary, the loss factor increases correspondingly.
Abstract: Drying behavior of blanched sweet potato in a cabinet
dryer using different five air temperatures (40-80°C) and ten sweet
potato varieties sliced to 5mm thickness were investigated. The
drying data were fitted to eight models. The Modified Henderson and
Pabis model gave the best fit to the experimental moisture ratio data
obtained during the drying of all the varieties while Newton (Lewis)
and Wang and Singh models gave the least fit. The values of Deff
obtained for Bophelo variety (1.27 x 10-9 to 1.77 x 10-9 m2/s) was
the least while that of S191 (1.93 x 10-9 to 2.47 x 10-9 m2/s) was the
highest which indicates that moisture diffusivity in sweet potato is
affected by the genetic factor. Activation energy values ranged from
0.27-6.54 kJ/mol. The lower activation energy indicates that drying
of sweet potato slices requires less energy and is hence a cost and
energy saving method. The drying behavior of blanched sweet potato
was investigated in a cabinet dryer. Drying time decreased
considerably with increase in hot air temperature. Out of the eight
models fitted, the Modified Henderson and Pabis model gave the best
fit to the experimental moisture ratio data on all the varieties while
Newton, Wang and Singh models gave the least. The lower activation
energy (0.27 - 6.54 kJ/mol) obtained indicates that drying of sweet
potato slices requires less energy and is hence a cost and energy
saving method.
Abstract: In this paper, we introduce a generalized Chebyshev
collocation method (GCCM) based on the generalized Chebyshev
polynomials for solving stiff systems. For employing a technique
of the embedded Runge-Kutta method used in explicit schemes, the
property of the generalized Chebyshev polynomials is used, in which
the nodes for the higher degree polynomial are overlapped with those
for the lower degree polynomial. The constructed algorithm controls
both the error and the time step size simultaneously and further
the errors at each integration step are embedded in the algorithm
itself, which provides the efficiency of the computational cost. For
the assessment of the effectiveness, numerical results obtained by the
proposed method and the Radau IIA are presented and compared.
Abstract: This paper is drawn from a wider study of the
management of gender, age and disability diversity in the banking
sector in the Kingdom of Saudi Arabia (KSA), which aims to develop
a framework for diversity management (DM) in this sector. The
paper focuses on the management of disability diversity. The purpose
of the paper is to assist in understanding disability DM in the banking
sector in KSA and to make suggestions for its enhancement. Hence, it
contributes to filling a research gap, as there is a dearth of literature
on disability DM, in KSA in general, and in the banking sector
specifically.
Discrimination against people with disabilities is a social issue that
has not been entirely overcome in any society. However, in KSA,
Islam informs almost every aspect of daily life including work, and
Islam is against discrimination. Hence, in KSA, there are regulations
to accommodate people with disabilities; however, employers are still
free not to hire job applicants with disabilities specifically because of
their condition. Indeed, disabled people are almost entirely absent
from the labour market.
There are 12 Saudi-owned or part-Saudi-owned banks in KSA and
two managers from each of these were interviewed, making a total of
24. The interviews aimed to investigate empirically the understanding
of managers in the banking sector in KSA of diversity management,
including disability DM, in the banking sector. The interview data
were analysed using thematic analysis. Two interviewees stated that
banks used the employment of people with disabilities to enhance
their corporate image, while five expressed the opinion that disabled
employees could contribute to the bank provided they did not have to
deal with customers face-to-face. Nine of the interviewees perceived
that disabled employees could be of value to the bank for their own
sake, not only in ‘behind the scenes’ roles. Another two interviewees
mentioned that employing disabled people could be part of the bank’s
community service programme and one thought it would be part of
the bank’s Saudisation efforts. The remaining five interviewees did
not know how disabled people could contribute to the bank.
The findings show that disability DM in the banking sector in
KSA is a relatively new concept, and is not yet well understood. In
the light of the findings, in order to achieve the purpose of the paper,
the following suggestions were made for the enhancement of
disability DM in the banking sector in KSA. A change in attitudes
towards disabled people is necessary. Such a change in the workplace
can only be achieved if a top-down approach is taken to the
integration of disabled people. Hence, it is suggested that
management and employees follow a course in disability awareness.
Further, a diversity officer in the HR department could enhance the
integration of disabled people into the banking workforce. It is also
suggested that greater government support is required through closely
monitored and enforced anti-discrimination legislation. Moreover,
flexible working arrangements such as part-time work would
facilitate the employment of disabled people and benefit other groups
of employees.
Abstract: In this study, we aim to demonstrate a microgrid
system experimental simulation for an easy understanding of a
large-scale microgrid system. This model is required for industrial
training and learning environments. However, in order to create an
exact representation of a microgrid system, the laboratory-scale
system must fulfill the requirements of a grid-connected inverter, in
which power values are assigned to the system to cope with the
intermittent output from renewable energy sources. Aside from that,
during fluctuations in load capacity, the grid-connected system must
be able to supply power from the utility grid side and microgrid side in
a balanced manner. Therefore, droop control is installed in the
inverter’s control board to maintain a balanced power sharing in both
sides. This power control in a stand-alone condition and droop control
in a grid-connected condition must be implemented in order to
maintain a stabilized system. Based on the experimental results, power
control and droop control can both be applied in the system by
comparing the experimental and reference values.
Abstract: We introduced an all-optical multicasting
characteristics with wavelength conversion based on a novel
all-optical triode using negative feedback semiconductor optical
amplifier. This study was demonstrated with a transfer speed of 10
Gb/s to a non-return zero 231-1 pseudorandom bit sequence system.
This multi-wavelength converter device can simultaneously provide
three channels of output signal with the support of non-inverted and
inverted conversion. We studied that an all-optical multicasting and
wavelength conversion accomplishing cross gain modulation is
effective in a semiconductor optical amplifier which is effective to
provide an inverted conversion thus negative feedback. The
relationship of received power of back to back signal and output
signals with wavelength 1535 nm, 1540 nm, 1545 nm, 1550 nm, and
1555 nm with bit error rate was investigated. It was reported that the
output signal wavelengths were successfully converted and modulated
with a power penalty of less than 8.7 dB, which the highest is 8.6 dB
while the lowest is 4.4 dB. It was proved that all-optical multicasting
and wavelength conversion using an optical triode with a negative
feedback by three channels at the same time at a speed of 10 Gb/s is a
promising device for the new wavelength conversion technology.
Abstract: The substantial similarity of fatigue mechanism in a
new test rig for rolling contact fatigue (RCF) has been investigated. A
new reduced-scale test rig is designed to perform controlled RCF
tests in wheel-rail materials. The fatigue mechanism of the rig is
evaluated in this study using a combined finite element-fatigue
prediction approach. The influences of loading conditions on fatigue
crack initiation have been studied. Furthermore, the effects of some
artificial defects (squat-shape) on fatigue lives are examined. To
simulate the vehicle-track interaction by means of the test rig, a threedimensional
finite element (FE) model is built up. The nonlinear
material behaviour of the rail steel is modelled in the contact
interface. The results of FE simulations are combined with the critical
plane concept to determine the material points with the greatest
possibility of fatigue failure. Based on the stress-strain responses, by
employing of previously postulated criteria for fatigue crack initiation
(plastic shakedown and ratchetting), fatigue life analysis is carried
out. The results are reported for various loading conditions and
different defect sizes. Afterward, the cyclic mechanism of the test rig
is evaluated from the operational viewpoint. The results of fatigue
life predictions are compared with the expected number of cycles of
the test rig by its cyclic nature. Finally, the estimative duration of the
experiments until fatigue crack initiation is roughly determined.
Abstract: Thanks to informational technologies development
every sphere of economics is becoming more and more datacentralized
as people are generating huge datasets containing
information on any aspect of their life. Applying research of such
data to human resources management allows getting scarce statistics
on labor market state including salary expectations and potential
employees’ typical career behavior, and this information can become
a reliable basis for management decisions.
The following article presents results of career behavior research
based on freely accessible resume data. Information used for study is
much wider than one usually uses in human resources surveys. That
is why there is enough data for statistically significant results even
for subgroups analysis.
Abstract: In the second decade of the XXI century the role of
tourism destination attractiveness is becoming increasingly important
for destination management. Competition in tourism market moves
from ordinary service quality to provision of unforgettable emotional
experience for tourists. The main purpose of the present study is to
identify the perception of the tourism destinations based on the
number of factors related to its tourist attractiveness.
The content analysis method was used to analyze the on-line
tourist feedback data immensely available in Social Media and in
travel related sites. The collected data made it possible to procure the
information which is necessary to understand the perceived
attractiveness of the destinations and key destination appeal factors
that are important for Russian leisure travelers.
Results of the present study demonstrate key attractiveness factors
or destination ‘properties’ that were unveiled as the most important
for Russian leisure tourists. The study targeted five main Spanish
tourism destinations that initially were determined by in-depth
interview with a number of Russian nationals who had visited Spain
at least once.
The research results can be useful for Spanish Tourism
Organization Representation office in Russia as well as for the other
national tourism organizations in order to promote their respective
destinations for Russian travelers focusing on main attractiveness
factors identified in this study.
Abstract: The crude oil in an oil well exists in various phases
such as gas, seawater, and sand, as well as oil. Therefore, a phase
separator is needed at the front of a single-phase pump for
pressurization and transfer. On the other hand, the application of a
multiphase pump can provide such advantages as simplification of the
equipment structure and cost savings, because there is no need for a
phase separation process. Therefore, the crude oil transfer method
using a multiphase pump is being applied to recently developed oil
wells. Due to this increase in demand, technical demands for the
development of multiphase pumps are sharply increasing, but the
progress of research into related technologies is insufficient, due to the
nature of multiphase pumps that require high levels of skills. This
study was conducted to verify the reliability of pump performance
evaluation using numerical analysis, which is the basis of the
development of a multiphase pump. For this study, a model was
designed by selecting the specifications of this study. The performance
of the designed model was evaluated through numerical analysis and
experiment. The results of the performance evaluation were compared
to verify the reliability of the result using numerical analysis.
Abstract: This paper presents the electromagnetic interference
(EMI) shielding effectiveness of rice husk and carbon nanotubes
(RHCNTs) composites in the X-band region (8.2-12.4 GHz). The
difference weight ratio of carbon nanotubes (CNTs) were mix with
the rice husk. The rectangular waveguide technique was used to
measure the complex permittivity of the RHCNTs composites
materials. The complex permittivity is represented in terms of both
the real and imaginary parts of permittivity in X-band frequency. The
conductivity of RHCNTs shows increasing when the ratio of CNTs
mixture increases. The composites materials were simulated using
Computer Simulation Technology (CST) Microwave Studio
simulation software. The shielding effectiveness of RHCNTs and
pure rice husk was compared. The highest EMI SE of 30 dB is
obtained for RHCNTs composites of 10 wt % CNTs with 10mm
thickness.
Abstract: One of the biggest challenges facing Theological/
Religious Education in Nigeria is access to quality learning materials.
For instance at the Trinity (Union) Theological College, Umuahia, it
was difficult for lecturers to access suitable and qualitative materials
for instruction especially the ones that would suit the African context
and stimulate a deep rooted interest among the students. Some
textbooks written by foreign authors were readily available in the
School Library, but were lacking in the College bookshops for
students to own copies. Even when the College was able to order
some of the books from abroad, it did not usher in the needed
enthusiasm expected from the students because they were either very
expensive or very difficult to understand during private studies. So it
became necessary to develop contextual materials which were
affordable and understandable, though with little success. The
National Open University of Nigeria (NOUN)’s innovation in the
development and sharing of learning resources through its Open
Courseware is a welcome development and of great assistance to
students. Apart from NOUN students who could easily access the
materials, many others from various theological/religious institutes
across the nation have benefited immensely. So, the thesis of this
paper is that the promotion of open educational resources in
theological/religious education in Nigeria would facilitate a better
informed/equipped religious leadership, which would in turn impact
its adherents for a healthier society and national development.
Adopting a narrative and historical approach within the context of
Nigeria’s educational system, the paper discusses: educational
traditions in Nigeria; challenges facing theological/religious
education in Nigeria; and benefits of open educational resources. The
study goes further to making recommendations on how OER could
positively influence theological/religious education in Nigeria. It is
expected that theologians, religious educators, and ODL practitioners
would find this work very useful.
Abstract: In structures, stress concentration is a factor of fatigue
fracture. Basically, the stress concentration is a phenomenon that
should be avoided. However, it is difficult to avoid the stress
concentration. Therefore, relaxation of the stress concentration is
important. The stress concentration arises from notches and circular
holes. There is a relaxation method that a composite patch covers a
notch and a circular hole. This relaxation method is used to repair
aerial wings, but it is not systematized. Composites are more
expensive than single materials. Accordingly, we propose the
relaxation method that a single material patch covers a notch and a
circular hole, and aim to systematize this relaxation method.
We performed FEA (Finite Element Analysis) about an object by
using a three-dimensional FEA model. The object was that a patch
adheres to a plate with a circular hole. And, a uniaxial tensile load acts
on the patched plate with a circular hole. In the three-dimensional FEA
model, it is not easy to model the adhesion layer. Basically, the yield
stress of the adhesive is smaller than that of adherents. Accordingly,
the adhesion layer gets to plastic deformation earlier than the adherents
under the yield load of adherents. Therefore, we propose the
three-dimensional FEA model which is applied a nonlinear elastic
region to the adhesion layer. The nonlinear elastic region was
calculated by a bilinear approximation. We compared the analysis
results with the tensile test results to confirm whether the analysis
model has usefulness. As a result, the analysis results agreed with the
tensile test results. And, we confirmed that the analysis model has
usefulness.
As a result that the three-dimensional FEA model was used to the
analysis, it was confirmed that an out-of-plane deformation occurred
to the patched plate with a circular hole. The out-of-plane deformation
causes stress increase of the patched plate with a circular hole.
Therefore, we investigated that the out-of-plane deformation affects
relaxation of the stress concentration in the plate with a circular hole
on this relaxation method. As a result, it was confirmed that the
out-of-plane deformation inhibits relaxation of the stress concentration
on the plate with a circular hole.
Abstract: Recently, there have been a lot of earthquakes in Japan.
It is necessary to promote seismic isolation devices for buildings. The
devices have been hardly diffused in attached houses, because the
devices are very expensive. We should develop a low-cost seismic
isolation device for detached houses. We suggested a new seismic
isolation device which uses a two-layer circular tube as a unit. If
hysteresis is produced in the two-layer circular tube under lateral
compression load, we think that the two-layer circular tube can have
energy absorbing capacity. It is necessary to contact the outer layer
and the inner layer to produce hysteresis. We have previously reported
how the inner layer comes in contact with the outer layer from a
perspective of analysis used mechanics of materials. We have clarified
that the inner layer comes in contact with the outer layer under a lateral
compression load. In this paper, we explored contact area between the
outer layer and the inner layer under a lateral compression load by
using FEA. We think that changing the inner layer’s thickness is
effective in increase the contact area. In order to change the inner
layer’s thickness, we changed the shape of the inner layer. As a result,
the contact area changes depending on the inner layer’s thickness.
Additionally, we experimented to check whether hysteresis occurs in
fact. As a consequence, we can reveal hysteresis in the two-layer
circular tube under the condition.
Abstract: This work presents a Computational Fluid Dynamics
(CFD) simulation of a butterfly valve used to control the flow of
combustible gas mixture in an industrial process setting.The work
uses CFD simulation to analyze the flow characteristics in the
vicinity of the valve, including the pressure distributions and
Frequency spectrum of the pressure pulsations downstream the valves
and the vortex shedding allow predicting the torque fluctuations
acting on the valve shaft and the possibility of generating mechanical
vibration and resonance.These fluctuations are due to aerodynamic
torque resulting from fluid turbulence and vortex shedding in the
valve vicinity.
The valve analyzed is located in a pipeline between two opposing
90o elbows, which exposes the valve and the surrounding structure to
the turbulence generated upstream and downstream the elbows at
either end of the pipe.CFD simulations show that the best location for
the valve from a vibration point of view is in the middle of the pipe
joining the elbows.
Abstract: Kigelia africana (Lam.) Benth. (Bignoniaceae) is a
reputed traditional remedy for various human ailments such as skin
diseases, microbial infections, melanoma, stomach troubles,
metabolic disorders, malaria and general pains. In spite of the fruit
being widely used for purposes related to its antibacterial and
antifungal properties, the chemical constituents associated with the
activity have not been fully identified. To elucidate the active
principles, we evaluated the antimicrobial activity of fruit extracts
and purified fractions against Staphylococcus aureus, Enterococcus
faecalis, Moraxella catarrhalis, Escherichia coli, Candida albicans
and Candida tropicalis. Shade-dried fruits were powdered and
extracted with hydroalcoholic (1:1) mixture by soaking at room
temperature for 72 h. The crude extract was further fractionated by
column chromatography, with successive elution using hexane,
dichloromethane, ethyl acetate, acetone and methanol. The
dichloromethane and ethyl acetate fractions were combined and
subjected to column chromatography to furnish a wax and oil from
the eluates of 20% and 40% ethyl acetate in hexane, respectively. The
GC-MS and GC×GC-MS results revealed that linoleic acid, linolenic
acid, palmitic acid, arachidic acid and stearic acid were the major
constituents in both oil and wax. The crude hydroalcoholic extract
exhibited the strongest activity with MICs of 0.125-0.5 mg/mL,
followed by the ethyl acetate (MICs = 0.125-1.0 mg/mL),
dichloromethane (MICs = 0.250-2.0 mg/mL), hexane (MICs = 0.25-
2.0 mg/mL), acetone (MICs = 0.5-2.0 mg/mL) and methanol (MICs =
1.0-2.0 mg/mL), whereas the wax (MICs = 2.0-4.0 mg/mL) and oil
(MICs = 4.0-8.0 mg/mL) showed poor activity. The study concludes
that synergistic interactions of chemical constituents could be
responsible for the antimicrobial activity of K. africana fruits, which
needs a more holistic approach to understand the mechanism of its
antimicrobial activity.