Abstract: In many communication and signal processing
systems, it is highly desirable to implement an efficient narrow-band
filter that decimate or interpolate the incoming signals. This paper
presents hardware efficient compensated CIC filter over a narrow
band frequency that increases the speed of down sampling by using
multiplierless decimation filters with polyphase FIR filter structure.
The proposed work analyzed the performance of compensated CIC
filter on the bases of the improvement of frequency response with
reduced hardware complexity in terms of no. of adders and
multipliers and produces the filtered results without any alterations.
CIC compensator filter demonstrated that by using compensation
with CIC filter improve the frequency response in passed of interest
26.57% with the reduction in hardware complexity 12.25%
multiplications per input sample (MPIS) and 23.4% additions per
input sample (APIS) w.r.t. FIR filter respectively.
Abstract: Application of hulls processing technologies, based on high-concentrated energy sources (laser and plasma technologies), allow improve shipbuilding production. It is typical for high-speed vessels construction using steel and aluminum alloys with high precision hulls required. Report describes high-performance technologies for plasma welding (using direct current of reversed polarity), laser, and hybrid laser-arc welding of hulls structures developed by JSC “SSTC”
Abstract: Fluid rheology may have essential impact on sound propagation in a liquid-filled pipe, especially, in a low frequency range. Rheological parameters of liquid are temperature-sensitive, which ultimately results in a temperature dependence of the wave speed and attenuation in the waveguide. The study is devoted to modeling of this effect at sound propagation in an elastic pipe with polymeric liquid, described by generalized Maxwell model with non-zero high-frequency viscosity. It is assumed that relaxation spectrum is distributed according to the Spriggs law; temperature impact on the liquid rheology is described on the basis of the temperature-superposition principle and activation theory. The dispersion equation for the waveguide, considered as a thin-walled tube with polymeric solution, is obtained within a quasi-one-dimensional formulation. Results of the study illustrate the influence of temperature on sound propagation in the system.
Abstract: There is an increasing demand for broadband services
in Indonesia. Therefore, the answer is the use of Ka-Band which has
some advantages such as wider bandwidth, the higher transmission
speeds, and smaller size of antenna in the ground. However, rain
attenuation is the primary factor in the degradation of signal at the
Kaband. In this paper, the author will determine whether the Ka-band
frequency can be implemented in Indonesia which has high intensity
of rainfall.
Abstract: Flow forming is widely used in many industries, especially in defence technology industries. Pressure vessels requirements are high precision, light weight, seamless and optimum strength. For large pressure vessels, flow forming by 3 rollers machine were used. In case of long range rocket motor case flow forming and welding of pressure vessels have been used for manufacturing. Due to complication of welding process, researchers had developed 4 meters length pressure vessels without weldment by 4 rollers flow forming machine. Design and preparation of preform work pieces are performed. The optimization of flow forming parameter such as feed rate, spindle speed and depth of cut will be discussed. The experimental result shown relation of flow forming parameters to quality of flow formed tube and prototype pressure vessels have been made.
Abstract: This paper presents the findings of an experimental investigation of important machining parameters for the horizontal boring tool modified to mouth with a horizontal lathe machine to bore an overlength workpiece. In order to verify a usability of a modified tool, design of experiment based on Taguchi method is performed. The parameters investigated are spindle speed, feed rate, depth of cut and length of workpiece. Taguchi L9 orthogonal array is selected for four factors three level parameters in order to minimize surface roughness (Ra and Rz) of S45C steel tubes. Signal to noise ratio analysis and analysis of variance (ANOVA) is performed to study an effect of said parameters and to optimize the machine setting for best surface finish. The controlled factors with most effect are depth of cut, spindle speed, length of workpiece, and feed rate in order. The confirmation test is performed to test the optimal setting obtained from Taguchi method and the result is satisfactory.
Abstract: An optimisation method using both global and local
optimisation is implemented to determine the flapping profile which
will produce the most lift for an experimental wing-actuation system.
The optimisation method is tested using a numerical quasi-steady
analysis. Results of an optimised flapping profile show a 20% increase
in lift generated as compared to flapping profiles obtained by high
speed cinematography of a Sympetrum frequens dragonfly. Initial
optimisation procedures showed 3166 objective function evaluations.
The global optimisation parameters - initial sample size and stage
one sample size, were altered to reduce the number of function
evaluations. Altering the stage one sample size had no significant
effect. It was found that reducing the initial sample size to 400
would allow a reduction in computational effort to approximately
1500 function evaluations without compromising the global solvers
ability to locate potential minima. To further reduce the optimisation
effort required, we increase the local solver’s convergence tolerance
criterion. An increase in the tolerance from 0.02N to 0.05N decreased
the number of function evaluations by another 20%. However, this
potentially reduces the maximum obtainable lift by up to 0.025N.
Abstract: The most important problem occurs on oil spills in sea
water is to reduce the oil spills size. This study deals with the
development of high pressurized nozzle using dispersion method for
oil leakage in offshore. 3D numerical simulation results were
obtained using ANSYS Fluent 13.0 code and correlate with the
experimental data for validation. This paper studies the contribution
of the process on flow speed and pressure of the flow from two
different geometrical designs of nozzles and to generate a spray
pattern suitable for dispersant application. Factor of size distribution
of droplets generated by the nozzle is calculated using pressures
ranging from 2 to 6 bars. Results obtain from both analyses shows a
significant spray pattern and flow distribution as well as distance.
Results also show a significant contribution on the effect of oil
leakage in terms of the diameter of the oil spills break up.
Abstract: Information technology is changing rapidly and the users’ expectations are also growing. Dealing with these changes in information technology, while satisfying the users’ needs and expectations is a big challenge. IT managers need to explore new mechanisms/strategies to enable them to cope with such challenges.
The objectives of this research are to identify the significant challenges that might face IT managers in higher education institutes in the face of the high and ever growing customer expectations and to propose possible solutions to cope with such high-speed changes in information technology.
To achieve these objectives, interviews with the IT professionals from different higher education institutes in Oman were conducted. In addition, documentation (printed and online) related to these institutions were studied and an intensive literature review of published work was examined.
The findings of this research are expected to give a better understanding of the challenges that might face the IT managers at higher education institutes. This acquired understanding is expected to highlight the importance of being adaptable and fast in keeping up with the ever-growing technological changes. Moreover, adopting different tools and technologies could assist IT managers in developing their organisations’ IT policies and strategies.
Abstract: The use of biodiesel in conventional diesel engines results in substantial reduction of unburned hydrocarbon, carbon monoxide and particulate matters. The performance, emission and combustion characteristics of a single cylinder four stroke variable compression ratio engine when fueled with Karanja (Pongamia) methyl ester and its 10-50 % blends with diesel (on a volume basis) are investigated and compared with standard diesel. The suitability of karanja methyl ester as a biofuel has been established in this study. The useful brake power obtained is similar to diesel fuel for all loads. Experiment has been conducted at a fixed engine speed of 1500 rpm, variable load and at compression ratios of 17.5:1 and 18.5:1. The impact of compression ratio on fuel consumption, combustion pressures and exhaust gas emissions has been investigated and presented. Optimum compression ratio which gives best performance has been identified. The results indicate longer ignition delay, maximum rate of pressure rise, lower heat release rate and higher mass fraction burnt at higher compression ratio for pongamia oil methyl ester when compared to that of diesel. The brake thermal efficiency for pongamia oil methyl ester blends and diesel has been calculated and the blend B20 is found to give maximum thermal efficiency. The blends when used as fuel results in reduction of carbon monoxide, hydrocarbon and increase in nitrogen oxides emissions. PME as an oxygenated fuel generated more complete combustion, which means increased torque and power. This is also supported with higher thermal efficiencies of the PME blends. NOx is slightly increased due to the higher combustion temperature and the presence of fuel oxygen with the blend at full load. PME as a new Biodiesel and its blends can be used in diesel engines without any engine modification.
Abstract: Chittagong is the commercial capital of Bangladesh.
Here Agrabad is one of the most commercial activity centers of
Chittagong. Due to many light industry and commercial land use,
Agrabad to CEPZ road at Agrabad is the only major road of
Chittagong port city which encompasses a huge number of vehicles
every day. It has many junctions which distribute traffic flow in
different roads. In these junctions vehicles gather at some conflict
point to create traffic jam and make the performance of the road
downward. This study is parallel focused on the existing level of
service with traffic volume, capacity, and speed by traffic survey.
After all of these analyses the performance of the road is determined
with finding the factors that influences the performance.
Abstract: Effect of blockage ratio on heat transfer from non-circular tube is studied experimentally. For doing this experiment a suction type low speed wind tunnel with test section dimension of 14×14×40 and velocity in rage of 7-20 m/s was designed. The blockage ratios varied between 1.5 to 7 and Reynolds number based on equivalent diameter varies in range of 7.5×103 to 17.5×103. The results show that by increasing blockage ratio from 1.5 to 7, drag coefficient of the cam shaped tube decreased about 55 percent. By increasing Reynolds number, Nusselt number of the cam shaped tube increases about 40 to 48 percent in all ranges of blockage ratios.
Abstract: Flanges are widely used for connecting valves, pipes and other industrial devices such as gearboxes. Method of producing a flange has a considerable impact on the manner of their involvement with the industrial engines and gearboxes. By Using die casting instead of sand casting and machining for manufacturing flanges, production speed and dimensional accuracy of the parts increases. Also, in die casting, obtained dimensions are close to final dimensions and hence the need for machining flanges after die casting process decreases which makes a significant savings in raw materials and improves the mechanical properties of flanges. In this paper, a typical die of an industrial helical gearbox flange (size ISO 50) was designed and die casting process for producing this type of flange was simulated using ProCAST software. The results of simulation were used for optimizing die design. Finally, using the results of the analysis, optimized die was built.
Abstract: CNFET has emerged as an alternative material to
silicon for high performance, high stability and low power SRAM
design in recent years. SRAM functions as cache memory in
computers and many portable devices. In this paper, a new SRAM
cell design based on CNFET technology is proposed. The proposed
SRAM cell design for CNFET is compared with SRAM cell designs
implemented with the conventional CMOS and FinFET in terms of
speed, power consumption, stability, and leakage current. The
HSPICE simulation and analysis show that the dynamic power
consumption of the proposed 8T CNFET SRAM cell’s is reduced
about 48% and the SNM is widened up to 56% compared to the
conventional CMOS SRAM structure at the expense of 2% leakage
power and 3% write delay increase.
Abstract: Nanoscale thermites such as the composite mixture of
nano-sized aluminum and molybdenum trioxide powders possess
several technical advantages such as much higher reaction rate and
shorter ignition delay, when compared to the conventional energetic
formulations made of micron-sized metal and oxidizer particles. In this
study, the self-propagation of combustion wave in compacted pellets
of nanoscale thermite composites is modeled and computationally
investigated by utilizing the activation energy reduction of aluminum
particles due to nanoscale particle sizes. The present computational
model predicts the speed of combustion wave propagation which is
good agreement with the corresponding experiments of thermite
reaction. Also, several characteristics of thermite reaction in nanoscale
composites are discussed including the ignition delay and combustion
wave structures.
Abstract: Laser beam welding has wide acceptability due to least welding distortion, low labour costs and convenient operation. However, laser welding for dissimilar titanium and aluminium alloys is a new area which is having wider applications in aerospace, aircraft, automotive, electronics and other industries. The present study is concerned with welding parameters namely laser power, welding speed, focusing distance and type of shielding gas and thereby evaluate welding performance of titanium and aluminium alloy thin sheets. This paper reviews the basic concepts associated with different parameters of Ti/Al sheet joint using Laser beam welding.
Abstract: In communication systems, frequency jump is a serious problem caused by the oscillators used. Kalman filters are used to detect that jump, despite the tradeoff between the noise level and the speed of the detection. In this paper, an improvement is introduced in the Kalman filter, through a nonlinear change in the bandwidth of the filter. Simulation results show a considerable improvement in the filter speed with a very low noise level. Additionally, the effect on the response to false alarms is also presented and false alarm rate show improvement.
Abstract: According to the independence, accuracy and controllability of the driving/braking torque of the distributed drive electric vehicle, a control strategy of differential drive assisted steering was designed. Firstly, the assisted curve under different speed and steering wheel torque was developed and the differential torques were distributed to the right and left front wheels. Then the steering return ability assisted control algorithm was designed. At last, the joint simulation was conducted by CarSim/Simulink. The result indicated: the differential drive assisted steering algorithm could provide enough steering drive-assisted under low speed and improve the steering portability. Along with the increase of the speed, the provided steering drive-assisted decreased. With the control algorithm, the steering stiffness of the steering system increased along with the increase of the speed, which ensures the driver’s road feeling. The control algorithm of differential drive assisted steering could avoid the understeer under low speed effectively.
Abstract: Unwanted side effects because of spectral aliasing and spectral imaging during signal processing would be the major concern over the sampling rate alteration. Multirate-multistage implementation of digital filter could come about a large computational saving than single rate filter suitable for sample rate conversion. This implementation can further improve through high-level architectural transformation in circuit level. Reallocating registers and relocating flip-flops across logic gates through retiming certainly a prominent sequential transformation technology, that optimize hardware circuits to achieve faster clocking speed without affecting the functionality. In this paper, we proposed an efficient compensated cascade Integrator comb (CIC) decimation filter structure that analyze the consequence of filter order variation which has a retimed FIR filter being compensator while using the cutset retiming technique and achieved an improvement in the passband droop by 14% to 39%, in computation time by 38.04%, 25.78%, 12.21%, 6.69% and 4.44% and reduction in path delay by 62.27%, 72%, 86.63%, 91.56% and 94.42% of 3, 6, 8, 12 and 24 order filter respectively than the non-retimed CIC compensation filter.
Abstract: Cognitive symptoms and behavioral symptoms may, in fact, overlap and be related to the level of the general cognitive function. We have measured the behavioral aspects of autism and its correlation to the cognitive ability in 30 children with ASD. We used a neuropsychological Battery CANTAB eclipse to evaluate the ASD children's cognitive ability. Individuals with ASD and challenging behaviors showed significant correlation between some cognitive abilities and Motor aspects. Based on these findings, we can conclude that the motor behavioral problems in autism affect specific cognitive abilities in ASDs such as comprehension, learning, reversal, acquisition, attention set shifting, and speed of reaction to one stimulus. Future researches should also focus on the relationship between motor stereotypes and other subtypes of repetitive behaviors, such as verbal stereotypes, ritual routine adherence, and the use of different types of CANTAB tests.