Abstract: Properly sized capacitor banks are connected across induction motors for several reasons including power factor correction, reducing distortions, increasing capacity, etc. Total harmonic distortion (THD) and power factor (PF) are used in such cases to quantify the improvements obtained through connection of the external capacitor banks. On the other hand, one of the methods for assessing the motor internal condition is by the use of Park-s pattern analysis. In spite of taking adequate precautionary measures, the capacitor banks may sometimes malfunction. Such a minor fault in the capacitor bank is often not apparently discernible. This may however, give rise to substantial degradation of power factor correction performance and may also damage the supply profile. The case is more severe with the fact that the Park-s pattern gets distorted due to such external capacitor faults, and can give anomalous results about motor internal fault analyses. The aim of this paper is to present simulation and hardware laboratory test results to have an understanding of the anomalies in harmonic distortion and Park-s pattern analyses in induction motors due to capacitor bank defects.
Abstract: This paper present some preliminary work on the
preparation and physicochemical caracterization of nanocomposite
MFI-alumina structures based on alumina hollow fibres. The fibers
are manufactured by a wet spinning process. α-alumina particles were
dispersed in a solution of polysulfone in NMP. The resulting slurry is
pressed through the annular gap of a spinneret into a precipitation
bath. The resulting green fibres are sintered. The mechanical strength
of the alumina hollow fibres is determined by a three-point-bending
test while the pore size is characterized by bubble-point testing. The
bending strength is in the range of 110 MPa while the average pore
size is 450 nm for an internal diameter of 1 mm and external diameter
of 1.7 mm. To characterize the MFI membranes various techniques
were used for physicochemical characterization of MFI–ceramic
hollow fibres membranes: The nitrogen adsorption, X-ray
diffractometry, scanning electron microscopy combined with X
emission microanalysis. Scanning Electron Microscopy (SEM) and
Energy Dispersive Microanalysis by the X-ray were used to observe
the morphology of the hollow fibre membranes (thickness,
infiltration into the carrier, defects, homogeneity). No surface film,
has been obtained, as observed by SEM and EDX analysis and
confirmed by high temperature variation of N2 and CO2 gas
permeances before cation exchange. Local analysis and characterise
(SEM and EDX) and overall (by ICP elemental analysis) were
conducted on two samples exchanged to determine the quantity and
distribution of the cation of cesium on the cross section fibre of the
zeolite between the cavities.
Abstract: It is very important to determine reference temperature when convective temperature because it should be used to calculate the temperature potential. This paper deals with the development of a new method that can determine heat transfer coefficient and reference free stream temperature simultaneously, based on transient heat transfer experiments with using two narrow band thermo-tropic liquid crystals (TLC's). The method is validated through error analysis in terms of the random uncertainties in the measured temperatures. It is shown how the uncertainties in heat transfer coefficient and free stream temperature can be reduced. The general method described in this paper is applicable to many heat transfer models with unknown free stream temperature.
Abstract: This paper presents the experimental results of
comparison between leakage currents and discharge currents. The leakage currents were obtained on polluted porcelain insulator.
Whereas, the discharge currents were obtained on lightly artificial
polluted porcelain specimen. The conducted measurements were
leakage current or discharge current and applied voltage. The insulator or specimen was in a hermetically sealed chamber, and the
current waveforms were analyzed using FFT.
The result indicated that the leakage current (LC) on low RH condition the fifth harmonic would be visible, and followed by the
seventh harmonic. The insulator had capacitive property. Otherwise,
on 99% relative humidity, the fifth harmonic would also be visible,
and the phase angle reached up to 12.2 degree. Whereas, on discharge current, the third harmonic would be visible, and followed
by fifth harmonic. The third harmonic would increase as pressure reduced. On this condition, the specimen had a non-linear characteristics
Abstract: This study utilizes the panel vector error correction
model (PVECM) to examine the relationship among corruption,
economic growth, and income inequality experienced within ten Asian
countries over the 1995 to 2010 period. According to the empirical
results, we do not support the common perception that corruption
decreases economic growth. On the contrary, we found that corruption
increases economic growth. Meanwhile, an increase in economic
growth will cause an increase in income inequality, although the effect
is insignificant. Similarly, an increase in income inequality will cause
an increase in economic growth but a decrease in corruption, although
the effect is also insignificant.
Abstract: In this work the design and characterization of an optoelectronic automated measurement system it is presented. The optoelectronic devices of this system are an optical transmitter, the optical components and the optical receiver, which were selected for a great precision of the system. The mechanical system allows free displacement of the components as well as the devices that generate the movement. The results, length and profile of the objects are display in Lab View.
Abstract: Flow-shop scheduling problem (FSP) deals with the
scheduling of a set of jobs that visit a set of machines in the same
order. The FSP is NP-hard, which means that an efficient algorithm
for solving the problem to optimality is unavailable. To meet the
requirements on time and to minimize the make-span performance of
large permutation flow-shop scheduling problems in which there are
sequence dependent setup times on each machine, this paper
develops one hybrid genetic algorithms (HGA). Proposed HGA
apply a modified approach to generate population of initial
chromosomes and also use an improved heuristic called the iterated
swap procedure to improve initial solutions. Also the author uses
three genetic operators to make good new offspring. The results are
compared to some recently developed heuristics and computational
experimental results show that the proposed HGA performs very
competitively with respect to accuracy and efficiency of solution.
Abstract: Technical laboratories are typically considered as
highly hazardous places in the polytechnic institution when
addressing the problems of high incidences and fatality rates. In
conjunction with several topics covered in the technical curricular,
safety and health precaution should be highlighted in order to
connect to few key ideas of being safe. Therefore the assessment of
safety awareness in terms of safety and health about hazardous and
risks at laboratories is needed and has to be incorporated with
technical education and other training programmes. The purpose of
this study was to determine the efficacy of technical laboratory safety
in one of the polytechnics in northern region. The study examined
three related issues that were; the availability of safety material and
equipment, safety practice adopted by technical teachers and
administrator-s safety attitudes in enforcing safety to the students. A
model of efficacy technical laboratory was developed to test the
linear relationship between existing safety material and equipment,
teachers- safety practice and administrators- attitude in enforcing
safety and to identify which of technical laboratory safety issues was
the most pertinent factor to realize safety in technical laboratory.
This was done by analyzing survey-based data sets particularly those
obtained from samples of 210 students in the polytechnic. The
Pearson Correlation was used to measure the association between the
variables and to test the research hypotheses. The result of the study
has found that there was a significant correlation between existing
safety material and equipment, safety practice adopted by teacher
and administrator-s attitude. There was also a significant relationship
between technical laboratory safety and safety practice adopted by
teacher and between technical laboratory safety and administrator
attitude. Hence, safety practice adopted by teacher and administrator
attitude is vital in realizing technical laboratory safety.
Abstract: The paper describes the workings for four models of
CONWIP systems used till date; the basic CONWIP system, the
hybrid CONWIP system, the multi-product CONWIP system, and the
parallel CONWIP system. The final novel model is introduced in this
paper in a general form. These models may be adopted for analysis
for both simulation studies and implementation on the shop floor. For
each model, input parameters of interest are highlighted and their
impacts on several system performance measures are addressed.
Abstract: This paper presents the experimental results of silicone rubber housing material for 24kV lightning arrester under artificial accelerated ageing test based on IEC 61109 specifications. Specimens having inclined and alternated shed made of HTV silicone rubber with ATH content and having leakage distance 625 mm were tested continuously 1000 hrs in artificial salt fog chamber. After 1000 hrs of salt fog ageing test, obviously surface erosion was observed on trunk between the upper large shed and the lower small shed near the energized end. Decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Chemical analysis by ATR-FTIR confirmed the observation results.
Abstract: Construction site safety in China has aroused
comprehensive concern all over the world. It is imperative to
investigate the main causes of poor construction site safety. This paper
divides all the causes into four aspects, namely the factors of workers,
object, environment and management and sets up the accident causes
element system based on Delphi Method. This is followed by the
application of structural equation modeling to examine the importance
of each aspect of causes from the standpoints of different roles related
to the construction respectively. The results indicate that all the four
aspects of factors are in need of improvement, and different roles have
different ideas considering the priority of those factors. The paper has
instructive significance for the practitioners to take measures to
improve construction site safety in China accordingly.
Abstract: The voice signal in Voice over Internet protocol (VoIP) system is processed through the best effort policy based IP network, which leads to the network degradations including delay, packet loss jitter. The work in this paper presents the implementation of finite impulse response (FIR) filter for voice quality improvement in the VoIP system through distributed arithmetic (DA) algorithm. The VoIP simulations are conducted with AMR-NB 6.70 kbps and G.729a speech coders at different packet loss rates and the performance of the enhanced VoIP signal is evaluated using the perceptual evaluation of speech quality (PESQ) measurement for narrowband signal. The results show reduction in the computational complexity in the system and significant improvement in the quality of the VoIP voice signal.
Abstract: All the geophysical phenomena including river
networks and flow time series are fractal events inherently and fractal
patterns can be investigated through their behaviors. A non-linear
system like a river basin can well be analyzed by a non-linear
measure such as the fractal analysis. A bilateral study is held on the
fractal properties of the river network and the river flow time series.
A moving window technique is utilized to scan the fractal properties
of them. Results depict both events follow the same strategy
regarding to the fractal properties. Both the river network and the
time series fractal dimension tend to saturate in a distinct value.
Abstract: Wireless capsule Endoscopy (WCE) has rapidly
shown its wide applications in medical domain last ten years
thanks to its noninvasiveness for patients and support for thorough
inspection through a patient-s entire digestive system including
small intestine. However, one of the main barriers to efficient
clinical inspection procedure is that it requires large amount of
effort for clinicians to inspect huge data collected during the
examination, i.e., over 55,000 frames in video. In this paper, we
propose a method to compute meaningful motion changes of
WCE by analyzing the obtained video frames based on regional
optical flow estimations. The computed motion vectors are used to
remove duplicate video frames caused by WCE-s imaging nature,
such as repetitive forward-backward motions from peristaltic
movements. The motion vectors are derived by calculating
directional component vectors in four local regions. Our
experiments are performed on small intestine area, which is of
main interest to clinical experts when using WCEs, and our
experimental results show significant frame reductions comparing
with a simple frame-to-frame similarity-based image reduction
method.
Abstract: This paper describes the design considerations of an
experimental setup for research and exploring the drives of batteryfed
electric vehicles. Effective setup composition and its components
are discussed. With experimental setup described in this paper,
durability and functional tests can be procured to the customers.
Multiple experiments are performed in the form of steady-state
system exploring, acceleration programs, multi-step tests (speed
control, torque control), load collectives or close-to-reality driving
tests (driving simulation). Main focus of the functional testing is on
the measurements of power and energy efficiency and investigations
in driving simulation mode, which are used for application purposes.
In order to enable the examination of the drive trains beyond
standard modes of operation, different other parameters can be
studied also.
Abstract: ZnO-SnO2 i.e. Zinc-Tin-Oxide (ZTO) thin films were
deposited on glass substrate with varying concentrations (ZnO:SnO2
- 100:0, 90:10, 70:30 and 50:50 wt.%) at room temperature by flash
evaporation technique. These deposited ZTO film were annealed at
450 0C in vacuum. These films were characterized to study the effect
of annealing on the structural, electrical, and optical properties.
Atomic force microscopy (AFM) and Scanning electron microscopy
(SEM) images manifest the surface morphology of these ZTO thin
films. The apparent growth of surface features revealed the formation
of nanostructure ZTO thin films. The small value of surface
roughness (root mean square RRMS) ensures the usefulness in
optical coatings. The sheet resistance was also found to be decreased
for both types of films with increasing concentration of SnO2. The
optical transmittance found to be decreased however blue shift has
been observed after annealing.
Abstract: Two different superhydrophobic surfaces were
elaborated and their oil repellency behavior was evaluated using
several liquid with different surface tension. A silicone rubber/SiO2
nanocomposite coated (A) on aluminum substrate by “spin-coating"
and the sample B was an anodized aluminum surface covered by
Teflon-like coating. A high static contact angle about ∼162° was
measured for two prepared surfaces on which the water droplet rolloff.
Scanning electron microscopy (SEM) showed the presence of
micro/nanostructures for both sample A and B similar to that of lotus
leaf.
However the sample A presented significantly different behaviour
of wettability against the low surface tension liquid. Sample A has
been wetted totally by oil (dodecan) droplet while sample B showed
oleophobic behaviour. Oleophobic property of Teflon like coating
can be contributed to the presence of CF2 and CF3 functional group
which was shown by XPS analysis.
Abstract: This research aims at development of the Multiple
Intelligences Measurement of Elementary Students. The structural
accuracy test and normality establishment are based on the Multiple
Intelligences Theory of Gardner. This theory consists of eight aspects
namely linguistics, logic and mathematics, visual-spatial relations,
body and movement, music, human relations, self-realization/selfunderstanding
and nature. The sample used in this research consists
of elementary school students (aged between 5-11 years). The size of
the sample group was determined by Yamane Table. The group has
2,504 students. Multistage Sampling was used. Basic statistical
analysis and construct validity testing were done using confirmatory
factor analysis. The research can be summarized as follows; 1.
Multiple Intelligences Measurement consisting of 120 items is
content-accurate. Internal consistent reliability according to the
method of Kuder-Richardson of the whole Multiple Intelligences
Measurement equals .91. The difficulty of the measurement test is
between .39-.83. Discrimination is between .21-.85. 2). The Multiple
Intelligences Measurement has construct validity in a good range,
that is 8 components and all 120 test items have statistical
significance level at .01. Chi-square value equals 4357.7; p=.00 at the
degree of freedom of 244 and Goodness of Fit Index equals 1.00.
Adjusted Goodness of Fit Index equals .92. Comparative Fit Index
(CFI) equals .68. Root Mean Squared Residual (RMR) equals 0.064
and Root Mean Square Error of Approximation equals 0.82. 3). The
normality of the Multiple Intelligences Measurement is categorized
into 3 levels. Those with high intelligence are those with percentiles
of more than 78. Those with moderate/medium intelligence are those
with percentiles between 24 and 77.9. Those with low intelligence
are those with percentiles from 23.9 downwards.
Abstract: The evaluation and measurement of human body
dimensions are achieved by physical anthropometry. This research
was conducted in view of the importance of anthropometric indices
of the face in forensic medicine, surgery, and medical imaging. The
main goal of this research is to optimization of facial feature point by
establishing a mathematical relationship among facial features and
used optimize feature points for age classification. Since selected
facial feature points are located to the area of mouth, nose, eyes and
eyebrow on facial images, all desire facial feature points are extracted
accurately. According this proposes method; sixteen Euclidean
distances are calculated from the eighteen selected facial feature
points vertically as well as horizontally. The mathematical
relationships among horizontal and vertical distances are established.
Moreover, it is also discovered that distances of the facial feature
follows a constant ratio due to age progression. The distances
between the specified features points increase with respect the age
progression of a human from his or her childhood but the ratio of the
distances does not change (d = 1 .618 ) . Finally, according to the
proposed mathematical relationship four independent feature
distances related to eight feature points are selected from sixteen
distances and eighteen feature point-s respectively. These four feature
distances are used for classification of age using Support Vector
Machine (SVM)-Sequential Minimal Optimization (SMO) algorithm
and shown around 96 % accuracy. Experiment result shows the
proposed system is effective and accurate for age classification.
Abstract: The nickel and gold nanoclusters as supported
catalysts were analyzed by XAS, XRD and XPS in order to
determine their local, global and electronic structure. The present
study has pointed out a strong deformation of the local structure of
the metal, due to its interaction with oxide supports. The average
particle size, the mean squares of the microstrain, the particle size
distribution and microstrain functions of the supported Ni and Au
catalysts were determined by XRD method using Generalized Fermi
Function for the X-ray line profiles approximation. Based on EXAFS
analysis we consider that the local structure of the investigated
systems is strongly distorted concerning the atomic number pairs.
Metal-support interaction is confirmed by the shape changes of the
probability densities of electron transitions: Ni K edge (1s →
continuum and 2p), Au LIII-edge (2p3/2 → continuum, 6s, 6d5/2 and
6d3/2). XPS investigations confirm the metal-support interaction at
their interface.