Abstract: The paper presents the results of simple measurements
conducted on a model of a wind-driven venturi-type room ventilator.
The ventilator design is new and was developed employing
mathematical modeling. However, the computational model was not
validated experimentally for the particular application considered.
The paper presents the performance of the ventilator model under
laboratory conditions, for five different wind tunnel speeds. The
results are used to both demonstrate the effectiveness of the new
design and to validate the computational model employed to develop
it.
Abstract: Eutrophication of surface water is one of the most
widespread environmental problems at present. Large number of
pilgrims and tourists visit sacred artificial tank known as “Brahma
Sarover” located at Kurukshetra, India to take holy dip and perform
religious ceremonies. The sources of pollutants include impurities in
feed water, mass bathing, religious offerings and windblown
particulate matter. Studies so far have focused mainly on assessing
water quality for bathing purpose by using physico-chemical and
bacteriological parameters. No effort has been made to assess nutrient
concentration and trophic status of the tank to take more appropriate
measures for improving water quality on long term basis. In the
present study, total nitrogen, total phosphorous and chlorophyll a
measurements have been done to assess the nutrient level and trophic
status of the tank. The results show presence of high concentration of
nutrients and Chlorophyll a indicating mesotrophic and eutrophic
state of the tank. Phosphorous has been observed as limiting nutrient
in the tank water.
Abstract: Groundlessness of application probability-statistic methods are especially shown at an early stage of the aviation GTE technical condition diagnosing, when the volume of the information has property of the fuzzy, limitations, uncertainty and efficiency of application of new technology Soft computing at these diagnosing stages by using the fuzzy logic and neural networks methods. It is made training with high accuracy of multiple linear and nonlinear models (the regression equations) received on the statistical fuzzy data basis. At the information sufficiency it is offered to use recurrent algorithm of aviation GTE technical condition identification on measurements of input and output parameters of the multiple linear and nonlinear generalized models at presence of noise measured (the new recursive least squares method (LSM)). As application of the given technique the estimation of the new operating aviation engine D30KU-154 technical condition at height H=10600 m was made.
Abstract: This paper describes a method to measure and
compensate a 4 axes ultra-precision machine tool that generates micro
patterns on the large surfaces. The grooving machine is usually used
for making a micro mold for many electrical parts such as a light guide
plate for LCD and fuel cells. The ultra precision machine tool has three
linear axes and one rotational table. Shaping is usually used to
generate micro patterns. In the case of 50 μm pitch and 25 μm height
pyramid pattern machining with a 90° wedge angle bite, one of linear
axis is used for long stroke motion for high cutting speed and other
linear axis are used for feeding. The triangular patterns can be
generated with many times of long stroke of one axis. Then 90°
rotation of work piece is needed to make pyramid patterns with
superposition of machined two triangular patterns.
To make a two dimensional positioning error, straightness of two
axes in out of plane, squareness between the each axis are important.
Positioning errors, straightness and squarness were measured by laser
interferometer system. Those were compensated and confirmed by
ISO230-6. One of difficult problem to measure the error motions is
squareness or parallelism of axis between the rotational table and
linear axis. It was investigated by simultaneous moving of rotary table
and XY axes. This compensation method is introduced in this paper.
Abstract: Memory Errors Detection and Correction aim to secure the transaction of data between the central processing unit of a satellite onboard computer and its local memory. In this paper, the application of a double-bit error detection and correction method is described and implemented in Field Programmable Gate Array (FPGA) technology. The performance of the proposed EDAC method is measured and compared with two different EDAC devices, using the same FPGA technology. Statistical analysis of single-event upset (SEU) and multiple-bit upset (MBU) activity in commercial memories onboard the first Algerian microsatellite Alsat-1 is given.
Abstract: One of the main research directions in CAD/CAM
machining area is the reducing of machining time.
The feedrate scheduling is one of the advanced techniques that
allows keeping constant the uncut chip area and as sequel to keep
constant the main cutting force. They are two main ways for feedrate
optimization. The first consists in the cutting force monitoring, which
presumes to use complex equipment for the force measurement and
after this, to set the feedrate regarding the cutting force variation. The
second way is to optimize the feedrate by keeping constant the
material removal rate regarding the cutting conditions.
In this paper there is proposed a new approach using an extended
database that replaces the system model.
The feedrate scheduling is determined based on the identification
of the reconfigurable machine tool, and the feed value determination
regarding the uncut chip section area, the contact length between tool
and blank and also regarding the geometrical roughness.
The first stage consists in the blank and tool monitoring for the
determination of actual profiles. The next stage is the determination
of programmed tool path that allows obtaining the piece target
profile.
The graphic representation environment models the tool and blank
regions and, after this, the tool model is positioned regarding the
blank model according to the programmed tool path. For each of
these positions the geometrical roughness value, the uncut chip area
and the contact length between tool and blank are calculated. Each of
these parameters are compared with the admissible values and
according to the result the feed value is established.
We can consider that this approach has the following advantages:
in case of complex cutting processes the prediction of cutting force is
possible; there is considered the real cutting profile which has
deviations from the theoretical profile; the blank-tool contact length
limitation is possible; it is possible to correct the programmed tool
path so that the target profile can be obtained.
Applying this method, there are obtained data sets which allow the
feedrate scheduling so that the uncut chip area is constant and, as a
result, the cutting force is constant, which allows to use more
efficiently the machine tool and to obtain the reduction of machining
time.
Abstract: This paper proposes a new technique for improving
the efficiency of software testing, which is based on a conventional
attempt to reduce test cases that have to be tested for any given
software. The approach utilizes the advantage of Regression Testing
where fewer test cases would lessen time consumption of the testing
as a whole. The technique also offers a means to perform test case
generation automatically. Compared to one of the techniques in the
literature where the tester has no option but to perform the test case
generation manually, the proposed technique provides a better
option. As for the test cases reduction, the technique uses simple
algebraic conditions to assign fixed values to variables (Maximum,
minimum and constant variables). By doing this, the variables values
would be limited within a definite range, resulting in fewer numbers
of possible test cases to process. The technique can also be used in
program loops and arrays.
Abstract: Hopfield model of associative memory is studied in this work. In particular, two main problems that it possesses: the apparition of spurious patterns in the learning phase, implying the well-known effect of storing the opposite pattern, and the problem of its reduced capacity, meaning that it is not possible to store a great amount of patterns without increasing the error probability in the retrieving phase. In this paper, a method to avoid spurious patterns is presented and studied, and an explanation of the previously mentioned effect is given. Another technique to increase the capacity of a network is proposed here, based on the idea of using several reference points when storing patterns. It is studied in depth, and an explicit formula for the capacity of the network with this technique is provided.
Abstract: Thermal behavior of fuel channel under loss of coolant accident (LOCA) is a major concern for nuclear reactor safety. LOCA along with failure of emergency cooling water system (ECC) may leads to mechanical deformations like sagging and ballooning. In order to understand the phenomenon an experiment has been carried out using 19 pin fuel element simulator. Main purpose of the experiment was to trace temperature profiles over the pressure tube, calandria tube and clad tubes of Indian Pressurized Heavy Water Reactor (IPHWR) under symmetrical and asymmetrical heat-up conditions. For simulating the fully voided scenario, symmetrical heating of pressure was carried out by injecting 13.2 KW (2 % of nominal power) to all the 19 pins and the temperatures of pressure tube, calandria tube and clad tubes were measured. During symmetrical heating the sagging of fuel channel was initiated at 460 °C and the highest temperature attained by PT was 650 °C . The decay heat from clad tubes was dissipated to moderator mainly by radiation and natural convection. The highest temperature of 680 °C was observed over the outer ring of clad tubes of fuel simulator. Again, to simulate partially voided condition, asymmetrical heating of pressure was carried out by supplying 8.0 kW power to upper 8 pins of fuel simulator and temperature profiles were measured. Along the circumference of pressure tube (PT) the highest temperature difference of 320 °C was observed, which highlights the magnitude of thermal stresses under partially voided conditions.
Abstract: Fixed-point simulation results are used for the performance measure of inverting matrices using a reconfigurable processing element. Matrices are inverted using the Cholesky decomposition algorithm. The reconfigurable processing element is capable of all required mathematical operations. The fixed-point word length analysis is based on simulations of different condition numbers and different matrix sizes.
Abstract: Skin color is an important visual cue for computer
vision systems involving human users. In this paper we combine skin
color and optical flow for detection and tracking of skin regions. We
apply these techniques to gesture recognition with encouraging
results. We propose a novel skin similarity measure. For grouping
detected skin regions we propose a novel skin region grouping
mechanism. The proposed techniques work with any number of skin
regions making them suitable for a multiuser scenario.
Abstract: The purpose of study is to demonstrate how the characteristics of technology and the process required for development of technology affect technology transfer from public organisations to industry on the technology level. In addition, using the advantage of the analytic level and the novel means of measuring technology convergence, we examine the characteristics of converging technologies as compared to non-converging technologies in technology transfer process. In sum, our study finds that a technology from the public sector is likely to be transferred when its readiness level is closer to generation of profit, when its stage of life cycle is early and when its economic values is high. Our findings also show that converging technologies are less likely to be transferred.
Abstract: In this paper we have developed a FDTD simulation
code which can treat wave propagation of a monopole antenna in a
metallic case which covers with PML, and performed a series of three
dimensional FDTD simulations of electromagnetic wave propagation
in this space .We also provide a measurement set up in antenna lab
and fortunately the simulations and measurements show good
agreement. According to simulation and measurement results, we
confirmed that the computer program which had been written in
FORTRAN, works correctly.
Abstract: The amplitude response of infrared (IR) sensors
depends on the reflectance properties of the target. Therefore, in
order to use IR sensor for measuring distances accurately, prior
knowledge of the surface must be known. This paper describes the
Phong Illumination Model for determining the properties of a surface
and subsequently calculating the distance to the surface. The angular
position of the IR sensor is computed as normal to the surface for
simplifying the calculation. Ultrasonic (US) sensor can provide the
initial information on distance to obtain the parameters for this
method. In addition, the experimental results obtained by using
LabView are discussed. More care should be taken when placing the
objects from the sensors during acquiring data since the small change
in angle could show very different distance than the actual one.
Since stereo camera vision systems do not perform well under some
environmental conditions such as plain wall, glass surfaces, or poor
lighting conditions, the IR and US sensors can be used additionally to
improve the overall vision systems of mobile robots.
Abstract: The innovative fuzzy estimator is used to estimate the
ground motion acceleration of the retaining structure in this study. The
Kalman filter without the input term and the fuzzy weighting recursive
least square estimator are two main portions of this method. The
innovation vector can be produced by the Kalman filter, and be
applied to the fuzzy weighting recursive least square estimator to
estimate the acceleration input over time. The excellent performance
of this estimator is demonstrated by comparing it with the use of
difference weighting function, the distinct levels of the measurement
noise covariance and the initial process noise covariance. The
availability and the precision of the proposed method proposed in this
study can be verified by comparing the actual value and the one
obtained by numerical simulation.
Abstract: In this paper we investigate the influence of external
noise on the inference of network structures. The purpose of our
simulations is to gain insights in the experimental design of microarray
experiments to infer, e.g., transcription regulatory networks
from microarray experiments. Here external noise means, that the
dynamics of the system under investigation, e.g., temporal changes of
mRNA concentration, is affected by measurement errors. Additionally
to external noise another problem occurs in the context of microarray
experiments. Practically, it is not possible to monitor the mRNA
concentration over an arbitrary long time period as demanded by the
statistical methods used to learn the underlying network structure. For
this reason, we use only short time series to make our simulations
more biologically plausible.
Abstract: This study numerically investigates the effects of Electrohydrodynamic on flow patterns and heat transfer enhancement within a cavity which is on the lower wall of channel. In this simulation, effects of using ground wire and ground plate on the flow patterns are compared. Moreover, the positions of electrode wire respecting with ground are tested in the range of angles θ = 0 - 180o. High electrical voltage exposes to air is 20 kV. Bulk mean velocity and temperature of inlet air are controlled at 0.1 m/s and 60 OC, respectively. The result shows when electric field is applied, swirling flow is appeared in the channel. In addition, swirling flow patterns in the main flow of using ground plate are widely spreader than that of using ground wire. Moreover, direction of swirling flow also affects the flow pattern and heat transfer in a cavity. These cause the using ground wire to give the maximum temperature and heat transfer higher than using ground plate. Furthermore, when the angle is at θ = 60o, high shear flow effect is obtained. This results show high strength of swirling flow and effective heat transfer enhancement.
Abstract: This paper presents a ray tracing simulation technique for characterize the radiowave propagation inside building. The implementation of an algorithm capable of enumerating a large number of propagation paths in interactive time for the special case of 2.5D. The effective dielectric constants of the building structure in the simulations are indicated. The study describes an efficient 2.5D model of ray tracing algorithm were compared with 3D model. The result of the first investigations is that the environment of the indoor wave significantly changes as we change the electric parameters of material constructions. A detailed analysis of the dependence of the indoor wave on the wideband characteristics of the channel: root mean square (RMS) delay spread characteristics and Mean excess delay, is also investigated.
Abstract: Heterogeneous catalysis is vital for a number of
chemical, refinery and pollution control processes. The use of
catalyst pellets of hollow cylindrical shape provide several distinct
advantages over other common shapes, and can therefore help to
enhance conversion levels in reactors. A better utilization of the
catalytic material is probably most notable of these features due to
the absence of the pellet core, which helps to significantly lower the
effect of the internal transport resistance. This is reflected in the
enhancement of the effectiveness factor. For the case of the first order
irreversible kinetics, a substantial increase in the effectiveness factor
can be obtained by varying shape parameters. Important shape
parameters of a finite hollow cylinder are the ratio of the inside to the
outside radii (κ) and the height to the diameter ratio (γ). A high value
of κ the generally helps to enhance the effectiveness factor. On the
other hand, lower values of the effectiveness factors are obtained
when the dimension of the height and the diameter are comparable.
Thus, the departure of parameter γ from the unity favors higher
effectiveness factor. Since a higher effectiveness factor is a measure
of a greater utilization of the catalytic material, higher conversion
levels can be achieved using the hollow cylindrical pellets possessing
optimized shape parameters.
Abstract: The unsteady wake of an EPPLER 361 airfoil in
pitching motion has been investigated in a subsonic wind tunnel by
hot-wire anemometry. The airfoil was given the pitching motion
about the one-quarter chord axis at reduced frequency of 0182.
Streamwise mean velocity profiles (wake profiles) were investigated
at several vertically aligned points behind the airfoil at one-quarter
chord downstream distance from trailing edge. Oscillation amplitude
and mean angle of attack were varied to determine the effects on
wake profiles. When the maximum dynamic angle of attack was
below the static stall angle of attack, weak effects on wake were
found by increasing oscillation amplitude and mean angle of attack.
But, for higher angles of attack strong unsteady effects were
appeared on the wake.