Abstract: This paper aims to study decomposition behavior in
pyrolytic environment of four lignocellulosic biomass (oil palm shell,
oil palm frond, rice husk and paddy straw), and two commercial
components of biomass (pure cellulose and lignin), performed in a
thermogravimetry analyzer (TGA). The unit which consists of a
microbalance and a furnace flowed with 100 cc (STP) min-1 Nitrogen,
N2 as inert. Heating rate was set at 20⁰C min-1 and temperature
started from 50 to 900⁰C. Hydrogen gas production during the
pyrolysis was observed using Agilent Gas Chromatography Analyzer
7890A. Oil palm shell, oil palm frond, paddy straw and rice husk
were found to be reactive enough in a pyrolytic environment of up to
900°C since pyrolysis of these biomass starts at temperature as low as
200°C and maximum value of weight loss is achieved at about
500°C. Since there was not much different in the cellulose,
hemicelluloses and lignin fractions between oil palm shell, oil palm
frond, paddy straw and rice husk, the T-50 and R-50 values obtained
are almost similar. H2 productions started rapidly at this temperature
as well due to the decompositions of biomass inside the TGA.
Biomass with more lignin content such as oil palm shell was found to
have longer duration of H2 production compared to materials of high
cellulose and hemicelluloses contents.
Abstract: In the upstream we place a piece of ring and rotate
it with 83Hz, 166Hz, 333Hz,and 666H to find the effect of the
periodic distortion.In the experiment this type of the perturbation
will not allow since the mechanical failure of any parts of the
equipment in the upstream will destroy the blade system. This type of
study will be only possible by CFD. We use two pumps NS32
(ENSAM) and three blades pump (Tamagawa Univ). The benchmark
computations were performed without perturbation parts, and confirm
the computational results well agreement in head-flow rate. We
obtained the pressure fluctuation growth rate that is representing the
global instability of the turbo-system. The fluctuating torque
components were 0.01Nm(5000rpm), 0.1Nm(10000rmp),
0.04Nm(20000rmp), 0.15Nm( 40000rmp) respectively. Only for
10000rpm(166Hz) the output toque was random, and it implies that it
creates unsteady flow by separations on the blades, and will reduce the
pressure loss significantly
Abstract: Reinforced concrete crash barriers used in road traffic
must meet a number of criteria. Crash barriers are laid lengthwise,
one behind another, and joined using specially designed steel locks.
While developing BSV reinforced concrete crash barriers (type
ŽPSV), experiments and calculations aimed to optimize the shape of
a newly designed lock and the reinforcement quantity and
distribution in a crash barrier were carried out. The tension carrying
capacity of two parallelly joined locks was solved experimentally.
Based on the performed experiments, adjustments of nonlinear
properties of steel were performed in the calculations. The obtained
results served as a basis to optimize the lock design using a
computational model that takes into account the plastic behaviour of
steel and the influence of the surrounding concrete [6]. The response
to the vehicle impact has been analyzed using a specially elaborated
complex computational model, comprising both the nonlinear model
of the damping wall or crash barrier and the detailed model of the
vehicle [7].
Abstract: A different concept for designing and detailing of
reinforced concrete precast frame structures is analyzed in this paper.
The new detailing of the joints derives from the special hybrid
moment frame joints. The special reinforcements of this alternative
detailing, named modified special hybrid joint, are bondless with
respect to both column and beams. Full scale tests were performed on
a plan model, which represents a part of 5 story structure, cropped in
the middle of the beams and columns spans. Theoretical approach
was developed, based on testing results on twice repaired model,
subjected to lateral seismic type loading. Discussion regarding the
modified special hybrid joint behavior and further on widening
research needed concludes the presentation.
Abstract: Solution to unsteady Navier-Stokes equation by Splitting method in physical orthogonal algebraic curvilinear coordinate system, also termed 'Non-linear grid system' is presented. The linear terms in Navier-Stokes equation are solved by Crank- Nicholson method while the non-linear term is solved by the second order Adams-Bashforth method. This work is meant to bring together the advantage of Splitting method as pressure-velocity solver of higher efficiency with the advantage of consuming Non-linear grid system which produce more accurate results in relatively equal number of grid points as compared to Cartesian grid. The validation of Splitting method as a solution of Navier-Stokes equation in Nonlinear grid system is done by comparison with the benchmark results for lid driven cavity flow by Ghia and some case studies including Backward Facing Step Flow Problem.
Abstract: This paper presents the work of signal discrimination
specifically for Electrocardiogram (ECG) waveform. ECG signal is
comprised of P, QRS, and T waves in each normal heart beat to
describe the pattern of heart rhythms corresponds to a specific
individual. Further medical diagnosis could be done to determine any
heart related disease using ECG information. The emphasis on QRS
Complex classification is further discussed to illustrate the
importance of it. Pan-Tompkins Algorithm, a widely known
technique has been adapted to realize the QRS Complex
classification process. There are eight steps involved namely
sampling, normalization, low pass filter, high pass filter (build a band
pass filter), derivation, squaring, averaging and lastly is the QRS
detection. The simulation results obtained is represented in a
Graphical User Interface (GUI) developed using MATLAB.
Abstract: In this paper, we consider nested sliding mode control of SISO nonlinear systems, perturbed by bounded matched and unmatched uncertainties. The systems are assumed to be in strict-feedback form. A step wise procedure is introduced to obtain the controller. In each step, a continuous sliding mode controller is designed as virtual control law. Then the next step sliding surface is defined by using this virtual controller. These sliding surfaces are selected as nonlinear static functions of the system states. Finally in the last step, smooth static state feedback control law is determined such that the output reaches the desired set-point while the system is forced arbitrary close to the intersection of sliding surfaces and the states remain bounded.
Abstract: Bioinformatics and Cheminformatics use computer as disciplines providing tools for acquisition, storage, processing, analysis, integrate data and for the development of potential applications of biological and chemical data. A chemical database is one of the databases that exclusively designed to store chemical information. NMRShiftDB is one of the main databases that used to represent the chemical structures in 2D or 3D structures. SMILES format is one of many ways to write a chemical structure in a linear format. In this study we extracted Antimicrobial Structures in SMILES format from NMRShiftDB and stored it in our Local Data Warehouse with its corresponding information. Additionally, we developed a searching tool that would response to user-s query using the JME Editor tool that allows user to draw or edit molecules and converts the drawn structure into SMILES format. We applied Quick Search algorithm to search for Antimicrobial Structures in our Local Data Ware House.
Abstract: The present study attempted to improve the Mercury
(Hg) sorption capacity of kanuma volcanic ash soil (KVAS) by
impregnating the cupper (Cu). Impregnation was executed by 1 and
5% Cu powder and sorption characterization of optimum Hg
removing Cu impregnated KVAS was performed under different
operational conditions, contact time, solution pH, sorbent dosage and
Hg concentration using the batch operation studies. The 1% Cu
impregnated KVAS pronounced optimum improvement (79%) in
removing Hg from water compare to control. The present
investigation determined the equilibrium state of maximum Hg
adsorption at 6 h contact period. The adsorption revealed a pH
dependent response and pH 3.5 showed maximum sorption capacity
of Hg. Freundlich isotherm model is well fitted with the experimental
data than that of Langmuir isotherm. It can be concluded that the Cu
impregnation improves the Hg sorption capacity of KVAS and 1%
Cu impregnated KVAS could be employed as cost-effective
adsorbent media for treating Hg contaminated water.
Abstract: This research aimed to study on the potential of
recycling organic waste in Suan Sunandha Rajabhat University as
compost. In doing so, the composition of solid waste generated in the
campus was investigated while physical and chemical properties of
organic waste were analyzed in order to evaluate the portion of waste
suitable for recycling as compost. As a result of the study, it was
found that (1) the amount of organic waste was averaged at 299.8
kg/day in which mixed food wastes had the highest amount of 191.9
kg/day followed by mixed leave & yard wastes and mixed fruit &
vegetable wastes at the amount of 66.3 and 41.6 kg/day respectively;
(2) physical and chemical properties of organic waste in terms of
moisture content was between 69.54 to 78.15%, major elements for
plant as N, P and K were 0.14 to 0.17%, 0.46 to 0.52% and 0.16 to
0.18% respectively, and carbon/nitrogen ratio (C/N) was about 15:1
to 17.5:1; (3) recycling organic waste as compost was designed by
aerobic decomposition using mixed food wastes : mixed leave & yard
wastes : mixed fruit & vegetable wastes at the portion of 3:2:1 by
weight in accordance with the potential of their amounts and their
physical and chemical properties.
Abstract: This study was designed to investigate the role of serum nitric oxide and sialic acid in the development of diabetic nephropathy as disease marker. Total 210 diabetic patients (age and sex matched) were selected followed by informed consent and divided into four groups (70 each) as I: control; II: diabetic; III: diabetic hypertensive; IV: diabetic nephropathy. The blood samples of all subjects were collected and analyzed for serum nitric oxide, sialic acid, fasting blood glucose, serum urea, creatinine, HbA1c and GFR. The BMI, systolic and diastolic blood pressures, blood glucose, HbA1c and serum sialic acid levels were high (p
Abstract: This paper presents a new approach for the prob-ability density function estimation using the Support Vector Ma-chines (SVM) and the Expectation Maximization (EM) algorithms.In the proposed approach, an advanced algorithm for the SVM den-sity estimation which incorporates the Mean Field theory in the learning process is used. Instead of using ad-hoc values for the para-meters of the kernel function which is used by the SVM algorithm,the proposed approach uses the EM algorithm for an automatic optimization of the kernel. Experimental evaluation using simulated data set shows encouraging results.
Abstract: Offset Double-Disk Opener (DDO) is a popular
furrow opener in conservation tillage. It has some limitations such as
negative suction to penetrate in the soil, hair pinning and mixing seed
and fertilizer in the slot. Because of importance of separation of seed
and fertilizer in the slot, by adding two horizontal mini disks to DDO
a modified opener was made (MDO) which placed the fertilizer
between and under two rows of seed. To consider performance of
novel opener an indoor comparison test between DDO and MDO was
performed at soil bin. The experiment was conducted with three
working speeds (3, 6 and 8 km h-1), two bulk densities of soil (1.1
and 1.4 Mg m-3) and two levels of residues (1 and 2 ton ha-1). The
experimental design consisted in a (3×2×2) complete randomized
factorial with three replicates for each test. Moisture of seed furrow,
separation of seed and fertilizer, hair pinning and resultant forces
acting on the openers were used as assessing indexes. There was no
significant difference between soil moisture content in slots created
by DDO and MDO at 0-4 cm depth, but at 4-8 cm the in the slot
created by MDO moisture content was higher about 9%. Horizontal
force for both openers increased with increasing speed and soil bulk
density. Vertical force for DDO was negative so it needed additional
weight for penetrating in the soil, but vertical force for MDO was
positive and, which can solve the challenge of penetration in the soil
in DDO. In soft soil with heavy residues some trash was pushed by
DDO into seed furrow (hair pinning) but at MDO seed were placed at
clean groove. Lateral and vertical separation of seed and fertilizer
was performed effectively by MDO (4.5 and 5 cm, respectively)
while DDO put seed and fertilizer close to each other. Overall, the
Modified Offset Double-disks (MDO) had better performance. So by
adapting this opener with no-tillage drillers it would possible to have
higher yield in conservation tillage where the most appropriate
opener is disk type.
Abstract: The fractal-shaped orifices are assumed to have a
significant effect on the pressure drop downstream pipe flow due to
their edge self-similarity shape which enhances the mixing
properties. Here, we investigate the pressure drop after these fractals
using a digital micro-manometer at different stations downstream a
turbulent flow pipe then a direct comparison has been made with the
pressure drop measured from regular orifices with the same flow
area. Our results showed that the fractal-shaped orifices have a
significant effect on the pressure drop downstream the flow. Also
the pressure drop measured across the fractal-shaped orifices is
noticed to be lower that that from ordinary orifices of the same flow
areas. This result could be important in designing piping systems
from point of view of losses consideration with the same flow
control area. This is promising to use the fractal-shaped orifices as
flowmeters as they can sense the pressure drop across them
accurately with minimum losses than the regular ones.
Abstract: The proper design of RF pulses in magnetic resonance imaging (MRI) has a direct impact on the quality of acquired images, and is needed for many applications. Several techniques have been proposed to obtain the RF pulse envelope given the desired slice profile. Unfortunately, these techniques do not take into account the limitations of practical implementation such as limited amplitude resolution. Moreover, implementing constraints for special RF pulses on most techniques is not possible. In this work, we propose to develop an approach for designing optimal RF pulses under theoretically any constraints. The new technique will pose the RF pulse design problem as a combinatorial optimization problem and uses efficient techniques from this area such as genetic algorithms (GA) to solve this problem. In particular, an objective function will be proposed as the norm of the difference between the desired profile and the one obtained from solving the Bloch equations for the current RF pulse design values. The proposed approach will be verified using analytical solution based RF simulations and compared to previous methods such as Shinnar-Le Roux (SLR) method, and analysis, selected, and tested the options and parameters that control the Genetic Algorithm (GA) can significantly affect its performance to get the best improved results and compared to previous works in this field. The results show a significant improvement over conventional design techniques, select the best options and parameters for GA to get most improvement over the previous works, and suggest the practicality of using of the new technique for most important applications as slice selection for large flip angles, in the area of unconventional spatial encoding, and another clinical use.
Abstract: This study was aimed for investigating of
manufacturing high aluminum content Mg alloys using a horizontal
twin roll caster. Recently, weight saving has been key issues for lighter
transport equipments as well as electronic component parts. As
alternative materials to aluminum alloys, developing magnesium alloy
with higher strength has been expected. Normally high Aluminum
content Mg alloy has poor ductility and is difficult to be rolled because
of its high strength. However, twin roll casting process is suitable for
manufacturing wrought Mg alloys because materials can be cast
directly from molten metal. In this study, manufacturing of high
aluminum content magnesium alloy sheet using the roll casting
process has been carried out. Effects of manufacturing parameter, such
as roll velocity, pouring temperature and roll gap, on casting was
investigated. A microscopic observation of the crystals of cross section
of as cast strip as well as rolled strip was conducted.
Abstract: Ten percent of the population will develop plantar
fasciitis (PF) during their lifetime. Two million people are treated
yearly accounting for 11-15% of visits to medical professionals.
Treatment ranges from conservative to surgical intervention. The
purpose of this study was to assess the effects of extracorporeal
shockwave therapy (ECSWT) on heel pain, function, range of motion
(ROM), and strength in patients with PF. One hundred subjects were
treated with ECSWT and measures were taken before and three
months after treatment. There was significant differences in visual
analog scale scores for pain at rest (p=0.0001); after activity (p=
0.0001) and; overall improvement (p=0.0001). There was also
significant improvement in Lower Extremity Functional Scale scores
(p=0.0001); ankle plantarflexion (p=0.0001), dorsiflexion (p=0.001),
and eversion (p=0.017),and first metatarsophalangeal joint flexion
(p=0.002) and extension (p=0.003) ROM. ECSWT is an effective
treatment improving heel pain, function and ROM in patients with
PF.
Abstract: This paper explores the scalability issues associated
with solving the Named Entity Recognition (NER) problem using
Support Vector Machines (SVM) and high-dimensional features. The
performance results of a set of experiments conducted using binary
and multi-class SVM with increasing training data sizes are
examined. The NER domain chosen for these experiments is the
biomedical publications domain, especially selected due to its
importance and inherent challenges. A simple machine learning
approach is used that eliminates prior language knowledge such as
part-of-speech or noun phrase tagging thereby allowing for its
applicability across languages. No domain-specific knowledge is
included. The accuracy measures achieved are comparable to those
obtained using more complex approaches, which constitutes a
motivation to investigate ways to improve the scalability of multiclass
SVM in order to make the solution more practical and useable.
Improving training time of multi-class SVM would make support
vector machines a more viable and practical machine learning
solution for real-world problems with large datasets. An initial
prototype results in great improvement of the training time at the
expense of memory requirements.
Abstract: In this study, communities of ammonia-oxidizing
archaea (AOA) and ammonia-oxidizing bacteria (AOB) in nitrifying
activated sludge (NAS) prepared by enriching sludge from a
municipal wastewater treatment plant in three continuous-flow
reactors receiving an inorganic medium containing different
ammonium concentrations of 2, 10, and 30 mM NH4
+-N (NAS2,
NAS10, and NAS30, respectively) were investigated using molecular
analysis. Results suggested that almost all AOA clones from NAS2,
NAS10, and NAS30 fell into the same AOA cluster and AOA
communities in NAS2 and NAS10 were more diverse than those of
NAS30. In contrast to AOA, AOB communities obviously shifted
from the seed sludge to enriched NASs and in each enriched NAS,
communities of AOB varied particularly. The seed sludge contained
members of N. communis cluster and N. oligotropha cluster. After it
was enriched under various ammonium loads, members of N.
communis cluster disappeared from all enriched NASs. AOB with
high affinity to ammonia presented in NAS 2, AOB with low affinity
to ammonia presented in NAS 30, and both types of AOB survived in
NAS 10. These demonstrated that ammonium load significantly
influenced AOB communities, but not AOA communities in enriched
NASs.
Abstract: For Seismic design, it is important to estimate,
maximum lateral displacement (inelastic displacement) of the
structures due to sever earthquakes for several reasons. Seismic
design provisions estimate the maximum roof and storey drifts
occurring in major earthquakes by amplifying the drifts of the
structures obtained by elastic analysis subjected to seismic design
load, with a coefficient named “displacement amplification factor"
which is greater than one. Here, this coefficient depends on various
parameters, such as ductility and overstrength factors. The present
research aims to evaluate the value of the displacement amplification
factor in seismic design codes and then tries to propose a value to
estimate the maximum lateral structural displacement from sever
earthquakes, without using non-linear analysis. In seismic codes,
since the displacement amplification is related to “force reduction
factor" hence; this aspect has been accepted in the current study.
Meanwhile, two methodologies are applied to evaluate the value of
displacement amplification factor and its relation with the force
reduction factor. In the first methodology, which is applied for all
structures, the ratio of displacement amplification and force reduction
factors is determined directly. Whereas, in the second methodology
that is applicable just for R/C moment resisting frame, the ratio is
obtained by calculating both factors, separately. The acquired results
of these methodologies are alike and estimate the ratio of two factors
from 1 to 1.2. The results indicate that the ratio of the displacement
amplification factor and the force reduction factor differs to those
proposed by seismic provisions such as NEHRP, IBC and Iranian
seismic code (standard no. 2800).