Abstract: In this paper fatigue crack initiation and propagation in notched plate under constant amplitude loading through tensile residual stress field of 2024 T351 Al-alloy plate were investigated. Residual stress field was generated by plastic deformation using finite element method (FEM) where isotropic hardening in Von Mises model was applied. Simulation of fatigue behavior was made on AFGROW code. It was shown that the fatigue crack initiation and propagation were affected by level of residual stress filed. In this investigation, the presence of tensile residual stresses at notch (hole) reduces considerably the total fatigue life. It was shown that the decreasing in stress reduces the fatigue crack growth rates.
Abstract: This paper shows the advantages of the material failure process simulation by improve finite elements with embedded discontinuities, using a new definition of traction vector, dependent on the discontinuity length and the angle. Particularly, two families of this kind of elements are compared: kinematically optimal symmetric and statically and kinematically optimal non-symmetric. The constitutive model to describe the behavior of the material in the symmetric formulation is a traction-displacement jump relationship equipped with softening after reaching the failure surface.
To show the validity of this symmetric formulation, representative numerical examples illustrating the performance of the proposed formulation are presented. It is shown that the non-symmetric family may over or underestimate the energy required to create a discontinuity, as this effect is related with the total length of the discontinuity, fact that is not noticed when the discontinuity path is a straight line.
Abstract: Over the course of the past century, the global
automotive industry-s stance towards safety has evolved from one of
contempt to one nearing reverence. A suspension system that
provides safe handling and cornering capabilities can, with the help
of an efficient braking system, improve safety to a large extent. The
aim of this research is to propose a new automotive brake rotor
design and to compare it with automotive vented disk rotor. Static
structural and transient thermal analysis have been carried out on the
vented disk rotor and proposed rotor designs to evaluate and compare
their performance. Finite element analysis was employed for both
static structural and transient thermal analysis. Structural analysis
was carried out to study the stress and deformation pattern of the
rotors under extreme loads. Time varying temperature load was
applied on the rotors and the temperature distribution was analysed
considering cooling parameters (convection and radiation). This
dissertation illustrates the use of Finite Element Methods to examine
models, concluding with a comparative study of the proposed rotor
design and the conventional vented disk rotor for structural stability
and thermal efficiency.
Abstract: For investigations of electromagnetic field
distributions in biological structures by Finite Element Method
(FEM), a method for automatic 3D model building of human
anatomical objects is developed. Models are made by meshed
structures and specific electromagnetic material properties for each
tissue type. Mesh is built according to specific FEM criteria for
achieving good solution accuracy. Several FEM models of
anatomical objects are built. Formulation using magnetic vector
potential and scalar electric potential (A-V, A) is used for modeling
of electromagnetic fields in human tissue objects. The developed
models are suitable for investigations of electromagnetic field
distributions in human tissues exposed in external fields during
magnetic stimulation, defibrillation, impedance tomography etc.
Abstract: Contact stress analysis between two spur gear
teeth was considered in different contact positions,
representing a pair of mating gears during rotation. A
programme has been developed to plot a pair of teeth in contact. This programme was run for each 3° of pinion
rotation from the first location of contact to the last location of
contact to produce 10 cases. Each case was represented a
sequence position of contact between these two teeth. The
programme gives graphic results for the profiles of these teeth
in each position and location of contact during rotation. Finite
element models were made for these cases and stress analysis
was done. The results were presented and finite element
analysis results were compared with theoretical calculations,
wherever available.
Abstract: The human knee joint has a three dimensional
geometry with multiple body articulations that produce complex
mechanical responses under loads that occur in everyday life and
sports activities. To produce the necessary joint compliance and
stability for optimal daily function various menisci and ligaments are
present while muscle forces are used to this effect. Therefore,
knowledge of the complex mechanical interactions of these load
bearing structures is necessary when treatment of relevant diseases is
evaluated and assisting devices are designed.
Numerical tools such as finite element analysis are suitable for
modeling such joints in order to understand their physics. They have
been used in the current study to develop an accurate human knee
joint and model its mechanical behavior. To evaluate the efficacy of
this articulated model, static load cases were used for comparison
purposes with previous experimentally verified modeling works
drawn from literature.
Abstract: The influence of eccentric discharge of stored solids in
squat silos has been highly valued by many researchers. However,
calculation method of lateral pressure under eccentric flowing still
needs to be deeply studied. In particular, the lateral pressure
distribution on vertical wall could not be accurately recognized
mainly because of its asymmetry. In order to build mechanical model
of lateral pressure, flow channel and flow pattern of stored solids in
squat silo are studied. In this passage, based on Janssen-s theory, the
method for calculating lateral static pressure in squat silos after
eccentric discharge is proposed. Calculative formulae are deduced for
each of three possible cases. This method is also focusing on
unsymmetrical distribution characteristic of silo wall normal
pressure. Finite element model is used to analysis and compare the
results of lateral pressure and the numerical results illustrate the
practicability of the theoretical method.
Abstract: Large metal and concrete structures suffer by various kinds of deterioration, and accurate prediction of the remaining life is important. This paper informs about two methods for its assessment. One method, suitable for steel bridges and other constructions exposed to fatigue, monitors the loads and damage accumulation using information systems for the operation and the finite element model of the construction. In addition to the operation load, the dead weight of the construction and thermal stresses can be included into the model. The second method is suitable for concrete bridges and other structures, which suffer by carbonatation and other degradation processes, driven by diffusion. The diffusion constant, important for the prediction of future development, can be determined from the depth-profile of pH, obtained by pH measurement at various depths. Comparison with measurements on real objects illustrates the suitability of both methods.
Abstract: This paper gives an overview of a deep drawing
process by pressurized liquid medium separated from the sheet by a
rubber diaphragm. Hydroforming deep drawing processing of sheet
metal parts provides a number of advantages over conventional
techniques. It generally increases the depth to diameter ratio possible
in cup drawing and minimizes the thickness variation of the drawn
cup. To explore the deformation mechanism, analytical and
numerical simulations are used for analyzing the drawing process of
an AA6061-T4 blank. The effects of key process parameters such as
coefficient of friction, initial thickness of the blank and radius
between cup wall and flange are investigated analytically and
numerically. The simulated results were in good agreement with the
results of the analytical model. According to finite element
simulations, the hydroforming deep drawing method provides a more
uniform thickness distribution compared to conventional deep
drawing and decreases the risk of tearing during the process.
Abstract: Two approaches for model development of a smart acoustic box are suggested in this paper: the finite element (FE) approach and the subspace identification. Both approaches result in a state-space model, which can be used for obtaining the frequency responses and for the controller design. In order to validate the developed FE model and to perform the subspace identification, an experimental set-up with the acoustic box and dSPACE system was used. Experimentally obtained frequency responses show good agreement with the frequency responses obtained from the FE model and from the identified model.
Abstract: As application of re-activation of backside on power
device Insulated Gate Bipolar Transistor (IGBT), laser annealing was
employed to irradiate amorphous silicon substrate, and resistivities
were measured using four point probe measurement. For annealing
the amorphous silicon two lasers were used at wavelength of visible
green (532 nm) together with Infrared (793 nm). While the green
laser efficiently increased temperature at top surface the Infrared
laser reached more deep inside and was effective for melting the
top surface. A finite element method was employed to evaluate time
dependent thermal distribution in silicon substrate.
Abstract: Dynamic shear test on simulated phantom can be used
to validate magnetic resonance elastography (MRE) measurements.
Phantom gel has been usually utilized for the cell culture of cartilage
and soft tissue and also been used for mechanical property
characterization using imaging systems. The viscoelastic property of
the phantom would be important for dynamic experiments and
analyses. In this study, An axisymmetric FE model is presented for
determining the dynamic shear behaviour of brain simulated phantom
using ABAQUS. The main objective of this study was to investigate
the effect of excitation frequencies and boundary conditions on shear
modulus and shear viscosity in viscoelastic media.
Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetical and thermal stresses remain major failures for
insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: Several methods are available for weight and shape
optimization of structures, among which Evolutionary Structural
Optimization (ESO) is one of the most widely used methods. In ESO,
however, the optimization criterion is completely case-dependent.
Moreover, only the improving solutions are accepted during the
search. In this paper a Simulated Annealing (SA) algorithm is used
for structural optimization problem. This algorithm differs from other
random search methods by accepting non-improving solutions. The
implementation of SA algorithm is done through reducing the
number of finite element analyses (function evaluations).
Computational results show that SA can efficiently and effectively
solve such optimization problems within short search time.
Abstract: Buoyancy driven heat transfer of nanofluids in a
cylindrical enclosure used as a control unit in the subsea hydrocarbon
injection wells is investigated in this study. The governing equations
obtained with the Boussinesq approximation are solved using Comsol
Multiphysics finite element analysis and simulation software. The
base fluid is water and CuO is used as nanoparticles. Solution is
obtained for nanoparticle solid volume fraction of 8% and for
Rayleigh number in the range of 105-107. The results show that
nanoparticle usage in the cylindrical electronic control unit has a
significant effect on the flow and heat transfer.
Abstract: A number of previous studies were rarely considered
the effects of transient non-uniform balloon expansion on evaluation
of the properties and behaviors of stents during stent expansion, nor
did they determine parameters to maximize the performances driven
by mechanical characteristics. Therefore, in order to fully understand
the mechanical characteristics and behaviors of stent, it is necessary to
consider a realistic modeling of transient non-uniform balloon-stent
expansion. The aim of the study is to propose design parameters
capable of improving the ability of vascular stent through a
comparative study of seven commercial stents using finite element
analyses of a realistic transient non-uniform balloon-stent expansion
process. In this study, seven representative commercialized stents were
evaluated by finite element (FE) analysis in terms of the criteria based
on the itemized list of Food and Drug Administration (FDA) and
European Standards (prEN). The results indicate that using stents
composed of opened unit cells connected by bend-shaped link
structures and controlling the geometrical and morphological features
of the unit cell strut or the link structure at the distal ends of stent may
improve mechanical characteristics of stent. This study provides a
better method at the realistic transient non-uniform balloon-stent
expansion by investigating the characteristics, behaviors, and
parameters capable of improving the ability of vascular stent.
Abstract: In this paper back-propagation artificial neural
network (BPANN) is employed to predict the limiting drawing ratio
(LDR) of the deep drawing process. To prepare a training set for
BPANN, some finite element simulations were carried out. die and
punch radius, die arc radius, friction coefficient, thickness, yield
strength of sheet and strain hardening exponent were used as the
input data and the LDR as the specified output used in the training of
neural network. As a result of the specified parameters, the program
will be able to estimate the LDR for any new given condition.
Comparing FEM and BPANN results, an acceptable correlation was
found.
Abstract: In this study, a vibration analysis was carried out of
symmetric angle-ply laminated composite plates with and without
square hole when subjected to compressive loads, numerically. A
buckling analysis is also performed to determine the buckling load of
laminated plates. For each fibre orientation, the compression load is
taken equal to 50% of the corresponding buckling load. In the
analysis, finite element method (FEM) was applied to perform
parametric studies, the effects of degree of orthotropy and stacking
sequence upon the fundamental frequencies and buckling loads are
discussed. The results show that the presence of a constant
compressive load tends to reduce uniformly the natural frequencies
for materials which have a low degree of orthotropy. However, this
reduction becomes non-uniform for materials with a higher degree of
orthotropy.
Abstract: In this study, the hydrogen transport phenomenon was
numerically evaluated by using hydrogen-enhanced localized
plasticity (HELP) mechanisms. Two dominant governing equations,
namely, the hydrogen transport model and the elasto-plastic model,
were introduced. In addition, the implicitly formulated equations of
the governing equations were implemented into ABAQUS UMAT
user-defined subroutines. The simulation results were compared to
published results to validate the proposed method.
Abstract: Restoration of endodontically treated teeth is a
common problem in dentistry, related to the fractures occurring in
such teeth and to concentration of forces little information regarding
variation of basic preparation guidelines in stress distribution has
been available. To date, there is still no agreement in the literature
about which material or technique can optimally restore
endodontically treated teeth. The aim of the present study was to
evaluate the influence of the core height and restoration materials on
corono-radicular restored upper first premolar. The first step of the
study was to achieve 3D models in order to analyze teeth, dowel and
core restorations and overlying full ceramic crowns. The FEM model
was obtained by importing the solid model into ANSYS finite
element analysis software. An occlusal load of 100 N was conducted,
and stresses occurring in the restorations, and teeth structures were
calculated. Numerical simulations provide a biomechanical
explanation for stress distribution in prosthetic restored teeth. Within
the limitations of the present study, it was found that the core height
has no important influence on the stress generated in coronoradicular
restored premolars. It can be drawn that the cervical regions
of the teeth and restorations were subjected to the highest stress
concentrations.