Abstract: Indoor air distribution has great impact on people-s thermal sensation. Therefore, how to remove the indoor excess heat becomes an important issue to create a thermally comfortable indoor environment. To expel the extra indoor heat effectively, this paper used a dynamic CFD approach to study the effect of an air-supply guide vane swinging periodically on the indoor air distribution within a model room. The numerical results revealed that the indoor heat transfer performance caused by the swing guide vane had close relation with the number of vortices developing under the inlet cold jet. At larger swing amplitude, two smaller vortices continued to shed outward under the cold jet and remove the indoor heat load more effectively. As a result, it can be found that the average Nusselt number on the floor increased with the increase of the swing amplitude of the guide vane.
Abstract: The modern telecommunication industry demands
higher capacity networks with high data rate. Orthogonal frequency
division multiplexing (OFDM) is a promising technique for high data
rate wireless communications at reasonable complexity in wireless
channels. OFDM has been adopted for many types of wireless
systems like wireless local area networks such as IEEE 802.11a, and
digital audio/video broadcasting (DAB/DVB). The proposed research
focuses on a concatenated coding scheme that improve the
performance of OFDM based wireless communications. It uses a
Redundant Residue Number System (RRNS) code as the outer code
and a convolutional code as the inner code. Here, a direct conversion
of analog signal to residue domain is done to reduce the conversion
complexity using sigma-delta based parallel analog-to-residue
converter. The bit error rate (BER) performances of the proposed
system under different channel conditions are investigated. These
include the effect of additive white Gaussian noise (AWGN),
multipath delay spread, peak power clipping and frame start
synchronization error. The simulation results show that the proposed
RRNS-Convolutional concatenated coding (RCCC) scheme provides
significant improvement in the system performance by exploiting the
inherent properties of RRNS.
Abstract: We have measured the pressure drop and convective
heat transfer coefficient of water – based AL(25nm),AL2O3(30nm)
and CuO(50nm) Nanofluids flowing through a uniform heated
circular tube in the fully developed laminar flow regime. The
experimental results show that the data for Nanofluids friction factor
show a good agreement with analytical prediction from the Darcy's
equation for single-phase flow. After reducing the experimental
results to the form of Reynolds, Rayleigh and Nusselt numbers. The
results show the local Nusselt number and temperature have
distribution with the non-dimensional axial distance from the tube
entry. Study decided that thenNanofluid as Newtonian fluids through
the design of the linear relationship between shear stress and the rate
of stress has been the study of three chains of the Nanofluid with
different concentrations and where the AL, AL2O3 and CuO – water
ranging from (0.25 - 2.5 vol %). In addition to measuring the four
properties of the Nanofluid in practice so as to ensure the validity of
equations of properties developed by the researchers in this area and
these properties is viscosity, specific heat, and density and found that
the difference does not exceed 3.5% for the experimental equations
between them and the practical. The study also demonstrated that the
amount of the increase in heat transfer coefficient for three types of
Nano fluid is AL, AL2O3, and CuO – Water and these ratios are
respectively (45%, 32%, 25%) with insulation and without insulation
(36%, 23%, 19%), and the statement of any of the cases the best
increase in heat transfer has been proven that using insulation is
better than not using it. I have been using three types of Nano
particles and one metallic Nanoparticle and two oxide Nanoparticle
and a statement, whichever gives the best increase in heat transfer.
Abstract: Results of Chilean wine classification based on the
information provided by an electronic nose are reported in this paper.
The classification scheme consists of two parts; in the first stage,
Principal Component Analysis is used as feature extraction method to
reduce the dimensionality of the original information. Then, Radial
Basis Functions Neural Networks is used as pattern recognition
technique to perform the classification. The objective of this study is
to classify different Cabernet Sauvignon, Merlot and Carménère wine
samples from different years, valleys and vineyards of Chile.
Abstract: The aim of the present work is to study the effect of annealing on the vibration damping capacity of high-chromium (16%) ferromagnetic steel. The alloys were prepared from raw materials of 99.9% purity melted in a high frequency induction furnace under high vacuum. The samples were heat-treated in vacuum at various temperatures (800 to 1200ºC) for 1 hour followed by slow cooling (120ºC/h). The inverted torsional pendulum method was used to evaluate the vibration damping capacity. The results indicated that the vibration damping capacity of the alloys is influenced by annealing and there exists a critical annealing temperature after 1000ºC. The damping capacity increases quickly below the critical temperature since the magnetic domains move more easily.
Abstract: Rule Discovery is an important technique for mining knowledge from large databases. Use of objective measures for discovering interesting rules lead to another data mining problem, although of reduced complexity. Data mining researchers have studied subjective measures of interestingness to reduce the volume of discovered rules to ultimately improve the overall efficiency of KDD process. In this paper we study novelty of the discovered rules as a subjective measure of interestingness. We propose a hybrid approach that uses objective and subjective measures to quantify novelty of the discovered rules in terms of their deviations from the known rules. We analyze the types of deviation that can arise between two rules and categorize the discovered rules according to the user specified threshold. We implement the proposed framework and experiment with some public datasets. The experimental results are quite promising.
Abstract: The world economic crises and budget constraints
have caused authorities, especially those in developing countries, to
rationalize water quality monitoring activities. Rationalization
consists of reducing the number of monitoring sites, the number of
samples, and/or the number of water quality variables measured. The
reduction in water quality variables is usually based on correlation. If
two variables exhibit high correlation, it is an indication that some of
the information produced may be redundant. Consequently, one
variable can be discontinued, and the other continues to be measured.
Later, the ordinary least squares (OLS) regression technique is
employed to reconstitute information about discontinued variable by
using the continuously measured one as an explanatory variable. In
this paper, two record extension techniques are employed to
reconstitute information about discontinued water quality variables,
the OLS and the Line of Organic Correlation (LOC). An empirical
experiment is conducted using water quality records from the Nile
Delta water quality monitoring network in Egypt. The record
extension techniques are compared for their ability to predict
different statistical parameters of the discontinued variables. Results
show that the OLS is better at estimating individual water quality
records. However, results indicate an underestimation of the variance
in the extended records. The LOC technique is superior in preserving
characteristics of the entire distribution and avoids underestimation
of the variance. It is concluded from this study that the OLS can be
used for the substitution of missing values, while LOC is preferable
for inferring statements about the probability distribution.
Abstract: The aim of this research was to calculate the thermal
properties of Au3Ni Nanowire. The molecular dynamics (MD)
simulation technique was used to obtain the effect of radius size on
the energy, the melting temperature and the latent heat of fusion at
the isobaric-isothermal (NPT) ensemble. The Quantum Sutton-Chen
(Q-SC) many body interatomic potentials energy have been used for
Gold (Au) and Nickel (Ni) elements and a mixing rule has been
devised to obtain the parameters of these potentials for nanowire
stats. Our MD simulation results show the melting temperature and
latent heat of fusion increase upon increasing diameter of nanowire.
Moreover, the cohesive energy decreased with increasing diameter of
nanowire.
Abstract: The mixed oxide nuclear fuel (MOX) of U and Pu contains several percent of fission products and minor actinides, such as neptunium, americium and curium. It is important to determine accurately the decay heat from Curium isotopes as they contribute significantly in the MOX fuel. This heat generation can cause samples to melt very quickly if excessive quantities of curium are present. In the present paper, we introduce a new approach that can predict the decay heat from curium isotopes. This work is a part of the project funded by King Abdulaziz City of Science and Technology (KASCT), Long-Term Comprehensive National Plan for Science, Technology and Innovations, and take place in King Abdulaziz University (KAU), Saudi Arabia. The approach is based on the numerical solution of coupled linear differential equations that describe decays and buildups of many nuclides to calculate the decay heat produced after shutdown. Results show the consistency and reliability of the approach applied.
Abstract: This study realizes an empirical investigation of main factors to develop an accounting career, stereotypes on accountants and accounting and perceptions on future career path for a sample of master students in accounting. The research provides some insight into what master students consider when choosing their future career paths. The most important two reasons chosen by students were “career opportunities" and “future earnings. They see accounting as structured, governed by conformity, requiring skills in working with numbers, monotonous, accurate, more efficient than effective but also absorbing, interesting and involving a certain degree of novelty. Although these students plan to start their careers in a multinational or accounting/audit firm, most of those plan to leave after five years. It resulted that women value more flexibility and time requiring special attention in retention policies practiced by firms.
Abstract: In this paper, we are presenting a new type of pointing interface for computers which provides mouse functionalities with near surface haptic feedback. Further, it can be configured as a haptic display where users may feel the basic geometrical shapes in the GUI by moving the finger on top of the device surface. These functionalities are achieved by tracking three dimensional positions of the neodymium magnet using Hall Effect sensors grid and generating like polarity haptic feedback using an electromagnet array. This interface brings the haptic sensations to the 3D space where previously it is felt only on top of the buttons of the haptic mouse implementations.
Abstract: M. Kemal Ataturk was a great leader who was fond of art and he had displayed his being fond of art many times. In his speeches and writings you can see that he had showed his approval to art and the importance of artists and art for the society. During the foundation of republic, he also wanted renovation in art as in other fields and ordered many novelties both in art and society. One of the greatest steps in realizing this was to prepare a national Turkish opera. In this study, it was studied how a Turkish opera, Özsoy was prepared in the context of social and political conditions of that time and what kind of processes it passed. As a result, it is seen that there was two main aims for Ataturk with this opera. First, Ataturk wanted to abolish the sectarian conflict between Iran and Turkey going on for centuries. The second and maybe the most important is that he wanted to make a revolution in the field of art and aimed to reach the level of civilized countries.
Abstract: An original Direct Numerical Simulation (DNS) method to tackle the problem of particulate flows at moderate to high concentration and finite Reynolds number is presented. Our method is built on the framework established by Glowinski and his coworkers [1] in the sense that we use their Distributed Lagrange Multiplier/Fictitious Domain (DLM/FD) formulation and their operator-splitting idea but differs in the treatment of particle collisions. The novelty of our contribution relies on replacing the simple artificial repulsive force based collision model usually employed in the literature by an efficient Discrete Element Method (DEM) granular solver. The use of our DEM solver enables us to consider particles of arbitrary shape (at least convex) and to account for actual contacts, in the sense that particles actually touch each other, in contrast with the simple repulsive force based collision model. We recently upgraded our serial code, GRIFF 1 [2], to full MPI capabilities. Our new code, PeliGRIFF 2, is developed under the framework of the full MPI open source platform PELICANS [3]. The new MPI capabilities of PeliGRIFF open new perspectives in the study of particulate flows and significantly increase the number of particles that can be considered in a full DNS approach: O(100000) in 2D and O(10000) in 3D. Results on the 2D/3D sedimentation/fluidization of isometric polygonal/polyedral particles with collisions are presented.
Abstract: Bythe development of the Internet, e-commerce has
got very popular between organizations. E-commerce means buying
and selling products and services over the Internet. One of the
challenging issues in e-commerce is how to attract the customers and
how to satisfy them. Therefore, it is important to keep good
relationship with the customers. This paper proposes a new model to
increase the customer satisfaction by introducing live-operator.
Live-operator is a system which is involved both with the customers
and the organization.In this system the customers feelthatthey receive
the service directly from the organization. This model decreases the
response time and the customer loss. Moreover, it increases customer
trust and the ability of organizations.
Abstract: An experimental and simulation flight test has been carried out to evaluate the longitudinal gliding characteristics of a lifting body with blunted half-cone geometry. The novelty here is the lifting body's pitch control mechanism, which consists of a pair of leading-edge rotating cylinders. Flight simulation uses aerodynamic data from computational fluid dynamics supported by wind-tunnel test. Flight test consists of releasing an aluminum lifting body model from a moving vehicle at the appropriate wind speed while measuring the lifting body's variation of altitude against time of flight. Results show that leading-edge rotating cylinder is able to give small amounts of improvement to the longitudinal stability and pitch control to the lifting body.
Abstract: Numerical investigation of the characteristics of an 80°
delta wing in combined force-pitch and free-roll is presented. The
implicit, upwind, flux-difference splitting, finite volume scheme and
the second-order-accurate finite difference scheme are employed to
solve the flow governing equations and Euler rigid-body dynamics
equations, respectively. The characteristics of the delta wing in
combined free-roll and large amplitude force-pitch is obtained
numerically and shows a well agreement with experimental data
qualitatively. The motion in combined force-pitch and free-roll
significantly reduces the lift force and transverse stabilities of the delta
wing, which is closely related to the flying safety. Investigations on
sensitive factors indicate that the roll-axis moment of inertia and the
structural damping have great influence on the frequency and
amplitude, respectively. Moreover, the turbulence model is considered
as an influencing factor in the investigation.
Abstract: This paper compares Hilditch, Rosenfeld, Zhang-
Suen, dan Nagendraprasad Wang Gupta (NWG) thinning algorithms
for Javanese character image recognition. Thinning is an effective
process when the focus in not on the size of the pattern, but rather on
the relative position of the strokes in the pattern. The research
analyzes the thinning of 60 Javanese characters.
Time-wise, Zhang-Suen algorithm gives the best results with the
average process time being 0.00455188 seconds. But if we look at
the percentage of pixels that meet one-pixel thickness, Rosenfelt
algorithm gives the best results, with a 99.98% success rate. From the
number of pixels that are erased, NWG algorithm gives the best
results with the average number of pixels erased being 84.12%. It can
be concluded that the Hilditch algorithm performs least successfully
compared to the other three algorithms.
Abstract: In this paper, a alternative structure method for
continuous time sigma delta modulator is presented. In this
modulator for implementation of integrators in loop filter second
generation current conveyors are employed. The modulator is
designed in CMOS technology and features low power consumption
(65db),
and with 180khZ bandwidth. Simulation results confirm that this
design is suitable for data converters.
Abstract: Experiments have been performed to investigate the radiation effects on mixed convection heat transfer for thermally developing airflow in vertical ducts with two differentially heated isothermal walls and two adiabatic walls. The investigation covers the Reynolds number Re = 800 to Re = 2900, heat flux varied from 256 W/m2 to 863 W/m2, hot wall temperature ranges from 27°C to 100 °C, aspect ratios 1 & 0.5 and the emissivity of internal walls are 0.05 and 0.85. In the present study, combined flow visualization was conducted to observe the flow patterns. The effect of surface temperature along the walls was studied to investigate the local Nusselt number variation within the duct. The result shows that flow condition and radiation significantly affect the total Nusselt number and tends to reduce the buoyancy condition.
Abstract: Heat transfer from two cam shape cylinder in tandem
arrangement had been studied numerically.
The distance between the centers of cylinders (L) is allowed to
vary to change the longitudinal pitch ratio (L/Deq). The equivalent
diameter of the cylinder (Deq) is 27.6 mm and longitudinal pitch ratio
varies in range 2