Abstract: The sequence Analyze, Design, Develop, Implement, and Evaluate (ADDIE) provides a powerful methodology for designing computer-based educational materials. Helping students to understand this design process sequence may be achieved by providing them with direct, guided experience. This article examines such help and guidance and the overall learning process from a student-s personal experience.
Abstract: Most buildings have been using anchor bolts
commonly for installing outdoor advertising structures. Anchor bolts
of common carbon steel are widely used and often installed
indiscriminately by inadequate installation standards. In the area
where strong winds frequently blow, falling accidents of outdoor
advertising structures can occur and cause a serious disaster, which is
very dangerous and to be prevented. In this regard, the development of
high-performance anchor bolts is urgently required. In the present
study, 25Cr-8Ni-1.5Si-1Mn-0.4C alloy was produced by traditional
vacuum induction melting (VIM) for the application of anchor bolt.
The alloy composition is revealed as a duplex microstructure from
thermodynamic phase analysis by FactSage® and confirmed by
metallographic experiment. Addition of Nitrogen to the alloy was
found to reduce the ferritic phase domain and significantly increase the
hardness and the tensile strength. Microstructure observation revealed
mixed structure of austenite and ferrite with fine carbide distributed
along the grain and phase boundaries.
Abstract: Chemical and physical functionalization of multiwalled
carbon nanotubes (MWCNT) has been commonly practiced to
achieve better dispersion of carbon nanotubes (CNTs) in polymer
matrix. This work describes various functionalization methods (acidtreatment,
non-ionic surfactant treatment with TritonX-100),
fabrication of MWCNT/PP nanocomposites via melt blending and
characterization of mechanical properties. Microscopy analysis
(FESEM, TEM, XPS) showed effective purification of MWCNTs
under acid treatment, and better dispersion under both chemical and
physical functionalization techniques combined, in their respective
order. Tensile tests showed increase in tensile strength for the
nanocomposites that contain MWCNTs up to 2 wt%. A decrease in
tensile strength was seen in samples that contain 4 wt% of MWCNTs
for both raw and Triton X-100 functionalized, signifying MWCNT
degradation/rebundling at composition with higher content of
MWCNTs. For the acid-treated MWCNTs, however, the tensile
results showed slight improvement even at 4wt%, indicating effective
dispersion of MWCNTs.
Abstract: The elimimation of mefenamic acid has been carried
out by photolysis, ozonation, adsorption onto activated carbon (AC)
and combinations of the previous single systems (O3+AC and
O3+UV). The results obtained indicate that mefenamic acid is not
photo-reactive, showing a relatively low quantum yield of the order
of 6 x 10-4 mol Einstein-1. Application of ozone to mefenamic
aqueous solutions instantaneously eliminates the pharmaceutical,
achieving simultaneously a 40% of mineralization. Addition of AC to
the ozonation process does not enhance the process, moreover,
mineralization is completely inhibited if compared to results obtained
by single ozonation. The combination of ozone and UV radiation led
to the best results in terms of mineralization (60% after 120 min).
Abstract: A novel direction-of-arrival (DOA) estimation technique, which uses a conventional multiple signal classification (MUSIC) algorithm with periodic signals, is applied to a single RF-port parasitic array antenna for direction finding. Simulation results show that the proposed method gives high resolution (1 degree) DOA estimation in an uncorrelated signal environment. The novelty lies in that the MUSIC algorithm is applied to a simplified antenna configuration. Only one RF port and one analogue-to-digital converter (ADC) are used in this antenna, which features low DC power consumption, low cost, and ease of fabrication. Modifications to the conventional MUSIC algorithm do not bring much additional complexity. The proposed technique is also free from the negative influence by the mutual coupling between elements. Therefore, the technique has great potential to be implemented into the existing wireless mobile communications systems, especially at the power consumption limited mobile terminals, to provide additional position location (PL) services.
Abstract: Five crystal modifications of water insoluble
artesunate were generated by recrystallizing it from various solvents
with improved physicochemical properties. These generated crystal
forms were characterized to select the most potent and soluble form.
SEM of all the forms showed changes in external shape leading them
to be different morphologically. DSC thermograms of Form III and
Form V showed broad endotherm peaks at 83.04oC and 76.96oC prior
to melting fusion of drug respectively. Calculated weight loss in TGA
revealed that Form III and Form V are methanol and acetone solvates
respectively. However, few additional peaks were appeared in XRPD
pattern in these two solvate forms. All forms exhibit exothermic
behavior in buffer and two solvates display maximum ease of
molecular release from the lattice. Methanol and acetone solvates
were found to be most soluble forms and exhibited higher
antimalarial efficacy showing higher survival rate (83.3%) after 30
days.
Abstract: The impact of noise upon live quality has become an
important aspect to make both urban and environmental policythroughout
Europe and in Turkey. Concern over the quality of urban
environments, including noise levels and declining quality of green
space, is over the past decade with increasing emphasis on designing
livable and sustainable communities. According to the World Health
Organization, noise pollution is the third most hazardous
environmental type of pollution which proceeded by only air (gas
emission) and water pollution. The research carried out in two
phases, the first stage of the research noise and plant types providing
the suction of noise was evaluated through literature study and at the
second stage, definite types (Juniperus horizontalis L., Spirea
vanhouetti Briot., Cotoneaster dammerii C.K., Berberis thunbergii
D.C., Pyracantha coccinea M. etc.) were selected for the city of
Konya. Trials were conducted on the highway of Konya. The biggest
value of noise reduction was 6.3 dB(A), 4.9 dB(A), 6.2 dB(A) value
with compared to the control which includes the group that formed
by the bushes at the distance of 7m, 11m, 20m from the source and
5m, 9m, 20m of plant width, respectively. In this paper, definitions
regarding to noise and its sources were made and the precautions
were taken against to noise that mentioned earlier with the adverse
effects of noise. Plantation design approaches and suggestions
concerning to the diversity to be used, which are peculiar to roadside,
were developed to discuss the role and the function of plant material
to reduce the noise of the traffic.
Abstract: In this paper, a new approach for design of a fully
differential second order current mode continuous-time sigma-delta
modulator is presented. For circuit implementation, square root
domain (SRD) translinear loop based on floating-gate MOS
transistors that operate in saturation region is employed. The
modulator features, low supply voltage, low power consumption
(8mW) and high dynamic range (55dB). Simulation results confirm
that this design is suitable for data converters.
Abstract: This paper presents a numerical study on surface heat
transfer characteristics of laminar air flows in parallel-plate dimpled
channels. The two-dimensional numerical model is provided by
commercial code FLUENT and the results are obtained for channels
with symmetrically opposing hemi-cylindrical cavities onto both
walls for Reynolds number ranging from 1000 to 2500. The influence
of variations in relative depth of dimples (the ratio of cavity depth to
the cavity curvature diameter), the number of them and the thermophysical
properties of channel walls on heat transfer enhancement is
studied. The results are evident for existence of an optimum value for
the relative depth of dimples in which the largest wall heat flux and
average Nusselt number can be achieved. In addition, the results of
conjugation simulation indicate that the overall influence of the ratio
of wall thermal conductivity to the one of the fluid on heat transfer
rate is not much significant and can be ignored.
Abstract: This study was conducted to determine the
effect of abdominal exercises versus abdominal supporting
belt on abdominal efficiency and inter-recti separation
following vaginal delivery.30 primiparous post-natal women
participated in this study. Their age ranged from (25 - 35)
years and their BMI < 30 Kg/m2. Participants were assigned
randomly into 2groups, participants of group (A) used
abdominal belt from the 2nd day following delivery, till the end
of puerperium (6 weeks), while participants of group (B)
engaged into abdominal exercises program from the 2nd day
following delivery for 6 weeks. The results of the present
study revealed that although there was no statistical difference
in waist circumference between both groups, participation in
abdominal exercise program produced a pronounced reduction
in waist/hip ratio, and inter-recti separation and also caused
significant increase in abdominal muscles strength (peak
torque, maximum repetition total work and average power)
higher than the use of abdominal belt.
Abstract: In the present study, the lattice Boltzmann Method (LBM) is applied for simulating of Natural Convection in an inclined open ended cavity. The cavity horizontal walls are insulated while the west wall is maintained at a uniform temperature higher than the ambient. Prandtl number is fixed to 0.71 (air) while Rayligh numbers, aspect ratio of the cavity are changed in the range of 103 to 104 and of 1-4, respectively. The numerical code is validated for the previously results for open ended cavities, and then the results of an inclined open ended cavity for various angles of rotating open ended cavity are presented. Result shows by increasing of aspect ratio, the average Nusselt number on hot wall decreases for all rotation angles. When gravity acceleration direction is opposite of standard gravity direction the convection heat transfer has a manner same as conduction.
Abstract: This paper proposes the use of Bayesian belief
networks (BBN) as a higher level of health risk assessment for a
dumping site of lead battery smelter factory. On the basis of the
epidemiological studies, the actual hospital attendance records and
expert experiences, the BBN is capable of capturing the probabilistic
relationships between the hazardous substances and their adverse
health effects, and accordingly inferring the morbidity of the adverse
health effects. The provision of the morbidity rates of the related
diseases is more informative and can alleviate the drawbacks of
conventional methods.
Abstract: One way for optimum loading of overdimensioning
conveyers is speed (capacity) decrement, with attention for
production capabilities and demands. At conveyers which drives with
three phase slip-ring induction motor, technically reasonable solution
for conveyer (driving motors) speed regulation is using constant
torque subsynchronous cascade with static semiconductor converter
and transformer for energy reversion to the power network. In the
paper is described mathematical model for parameter calculation of
two-motors 6 kV subsynchronous cascade. It is also demonstrated
that applying of this cascade gave several good properties, foremost
in electrical energy saving, also in improving of other energy
indexes, and finally that results in cost reduction of complete
electrical motor drive.
Abstract: A hardware efficient, multi mode, re-configurable
architecture of interleaver/de-interleaver for multiple standards,
like DVB, WiMAX and WLAN is presented. The interleavers
consume a large part of silicon area when implemented by using
conventional methods as they use memories to store permutation
patterns. In addition, different types of interleavers in different
standards cannot share the hardware due to different construction
methodologies. The novelty of the work presented in this paper is
threefold: 1) Mapping of vital types of interleavers including
convolutional interleaver onto a single architecture with flexibility
to change interleaver size; 2) Hardware complexity for channel
interleaving in WiMAX is reduced by using 2-D realization of the
interleaver functions; and 3) Silicon cost overheads reduced by
avoiding the use of small memories. The proposed architecture
consumes 0.18mm2 silicon area for 0.12μm process and can
operate at a frequency of 140 MHz. The reduced complexity helps
in minimizing the memory utilization, and at the same time
provides strong support to on-the-fly computation of permutation
patterns.
Abstract: Vacuum membrane distillation (VMD) process can be
used for water purification or the desalination of salt water. The
process simply consists of a flat sheet hydrophobic micro porous
PTFE membrane and diaphragm vacuum pump without a condenser
for the water recovery or trap. The feed was used aqueous NaCl
solution. The VMD experiments were performed to evaluate the heat
and mass transfer coefficient of the boundary layer in a membrane
module. The only operating parameters are feed inlet temperature,
and feed flow rate were investigated. The permeate flux was strongly
affected by the feed inlet temperature, feed flow rate, and boundary
layer heat transfer coefficient. Since lowering the temperature
polarization coefficient is essential enhance the process performance
considerable and maximizing the heat transfer coefficient for
maximizes the mass flux of distillate water. In this paper, the results
of VMD experiments are used to measure the boundary layer heat
transfer coefficient, and the experimental results are used to reevaluate
the empirical constants in the Dittus- Boelter equation.
Abstract: Banishing hunger from the face of earth has been
frequently expressed in various international, national and regional
level conferences since 1974. Providing food security has become
important issue across the world particularly in developing countries.
In a developing country like India, where growth rate of population is
more than that of the food grains production, food security is a
question of great concern. According to the International Food Policy
Research Institute's Global Hunger Index, 2011, India ranks 67 of the
81 countries of the world with the worst food security status. After
Green Revolution, India became a food surplus country. Its
production has increased from 74.23 million tonnes in 1966-67 to
257.44 million tonnes in 2011-12. But after achieving selfsufficiency
in food during last three decades, the country is now
facing new challenges due to increasing population, climate change,
stagnation in farm productivity. Therefore, the main objective of the
present paper is to examine the food security situation at national
level in the country and further to explain the paradox of food
insecurity in a food surplus state of India i.e in Punjab at micro level.
In order to achieve the said objectives, secondary data collected from
the Ministry of Agriculture and the Agriculture department of Punjab
State was analyzed. The result of the study showed that despite
having surplus food production the country is still facing food
insecurity problem at micro level. Within the Kandi belt of Punjab
state, the area adjacent to plains is food secure while the area along
the hills falls in food insecure zone.
The present paper is divided into following three sections (i)
Introduction, (ii) Analysis of food security situation at national level
as well as micro level (Kandi belt of Punjab State) (iii) Concluding
Observations
Abstract: This paper proposes a hybrid method for eyes localization
in facial images. The novelty is in combining techniques
that utilise colour, edge and illumination cues to improve accuracy.
The method is based on the observation that eye regions have dark
colour, high density of edges and low illumination as compared
to other parts of face. The first step in the method is to extract
connected regions from facial images using colour, edge density and
illumination cues separately. Some of the regions are then removed
by applying rules that are based on the general geometry and shape
of eyes. The remaining connected regions obtained through these
three cues are then combined in a systematic way to enhance the
identification of the candidate regions for the eyes. The geometry
and shape based rules are then applied again to further remove the
false eye regions. The proposed method was tested using images from
the PICS facial images database. The proposed method has 93.7%
and 87% accuracies for initial blobs extraction and final eye detection
respectively.
Abstract: Addition of milli or micro sized particles to the heat
transfer fluid is one of the many techniques employed for improving
heat transfer rate. Though this looks simple, this method has
practical problems such as high pressure loss, clogging and erosion
of the material of construction. These problems can be overcome by
using nanofluids, which is a dispersion of nanosized particles in a
base fluid. Nanoparticles increase the thermal conductivity of the
base fluid manifold which in turn increases the heat transfer rate.
Nanoparticles also increase the viscosity of the basefluid resulting in
higher pressure drop for the nanofluid compared to the base fluid. So
it is imperative that the Reynolds number (Re) and the volume
fraction have to be optimum for better thermal hydraulic
effectiveness. In this work, the heat transfer enhancement using
aluminium oxide nanofluid using low and high volume fraction
nanofluids in turbulent pipe flow with constant wall temperature has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach. Nanofluid, up till
a volume fraction of 1% is found to be an effective heat transfer
enhancement technique. The Nusselt number (Nu) and friction factor
predictions for the low volume fractions (i.e. 0.02%, 0.1 and 0.5%)
agree very well with the experimental values of Sundar and Sharma
(2010). While, predictions for the high volume fraction nanofluids
(i.e. 1%, 4% and 6%) are found to have reasonable agreement with
both experimental and numerical results available in the literature.
So the computationally inexpensive single phase approach can be
used for heat transfer and pressure drop prediction of new nanofluids.
Abstract: Cenozoic basalts found in Jiangsu province of eastern
China include tholeiites and alkali basalts. The present paper analyzed
the major, trace elements, rare earth elements of these Cenozoic
basalts and combined with Sr-Nd isotopic compositions proposed by
Chen et al. (1990)[1] in the literatures to discuss the petrogenesis of
these basalts and the geochemical characteristics of the source mantle.
Based on major, trace elements and fractional crystallization model
established by Brooks and Nielsen (1982)[2] we suggest that the
basaltic magma has experienced olivine + clinopyroxene fractionation
during its evolution. The chemical compositions of basaltic rocks from
Jiangsu province indicate that these basalts may belong to the same
magmatic system. Spidergrams reveal that Cenozoic basalts from
Jiangsu province have geochemical characteristics similar to those of
ocean island basalts(OIB). The slight positive Nb and Ti anomalies
found in basaltic rocks of this study suggest the presence of Ti-bearing
minerals in the mantle source and these Ti-bearing minerals had
contributed to basaltic magma during partial melting, indicating a
metasomatic event might have occurred before the partial melting.
Based on the Sr vs. Nd isotopic ratio plots, we suggest that Jiangsu
basalts may be derived from partial melting of mantle source which
may represent two-end members mixing of DMM and EM-I. Some
Jiangsu basaltic magma may be derived from partial melting of EM-I
heated by the upwelling asthenospheric mantle or asthenospheric
diapirism.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.