Abstract: Turbulent heat transfer to fluid flow through channel with triangular ribs of different angles are presented in this paper. Ansys 14 ICEM and Ansys 14 Fluent are used for meshing process and solving Navier stokes equations respectively. In this investigation three angles of triangular ribs with the range of Reynolds number varied from 20000 to 60000 at constant surface temperature are considered. The results show that the Nusselt number increases with the increase of Reynolds number for all cases at constant surface temperature. According to the profile of local Nusselt number on ribs walled of channel, the peak is at the midpoint between the two ribs. The maximum value of average Nusselt number is obtained for triangular ribs of angel 60°and at Reynolds number of 60000 compared to the Nusselt number for the ribs of angel 90° and 45° and at same Reynolds number. The recirculation regions generated by the ribs corresponding to the velocity streamline show the largest recirculation region at triangular ribs of angle 60° which also provides the highest enhancement of heat transfer.
Abstract: In this paper, a two-dimensional mathematical model is developed for estimating the extent of inland inundation due to Indonesian tsunami of 2004 along the coastal belts of Peninsular Malaysia and Thailand. The model consists of the shallow water equations together with open and coastal boundary conditions. In order to route the water wave towards the land, the coastal boundary is treated as a time dependent moving boundary. For computation of tsunami inundation, the initial tsunami wave is generated in the deep ocean with the strength of the Indonesian tsunami of 2004. Several numerical experiments are carried out by changing the slope of the beach to examine the extent of inundation with slope. The simulated inundation is found to decrease with the increase of the slope of the orography. Correlation between inundation / recession and run-up are found to be directly proportional to each other.
Abstract: Unsteady natural convection and heat transfer in a square cavity partially filled with porous media using a thermal
non-equilibrium model is studied in this paper. The left vertical wall is
maintained at a constant hot temperature Th and the right vertical wall
is maintained at a constant cold temperature Tc, while the horizontal
walls are adiabatic. The governing equations are obtained by applying
the Darcy model and Boussinesq approximation. COMSOL’s finite
element method is used to solve the non-dimensional governing
equations together with specified boundary conditions. The governing
parameters of this study are the Rayleigh number (Ra = 10^5, and Ra = 10^6 ), Darcy namber (Da = 10^−2, and Da = 10^−3),
the modified thermal conductivity ratio (10^−1 ≤ γ ≤ 10^4), the inter-phase heat transfer coefficien (10^−1 ≤ H ≤ 10^3) and the
time dependent (0.001 ≤ τ ≤ 0.2). The results presented for
values of the governing parameters in terms of streamlines in both
fluid/porous-layer, isotherms of fluid in fluid/porous-layer, isotherms
of solid in porous layer, and average Nusselt number.
Abstract: One of the common problems encountered in software
engineering is addressing and responding to the changing nature of
requirements. While several approaches have been devised to address
this issue, ranging from instilling resistance to changing requirements
in order to mitigate impact to project schedules, to developing an
agile mindset towards requirements, the approach discussed in this
paper is one of conceptualizing the delta in requirement and
modeling it, in order to plan a response to it. To provide some
context here, change is first formally identified and categorized as
either formal change or informal change. While agile methodology
facilitates informal change, the approach discussed in this paper
seeks to develop the idea of facilitating formal change. To collect,
document meta-requirements that represent the phenomena of change
would be a pro-active measure towards building a realistic cognition
of the requirements entity that can further be harnessed in the
software engineering process.
Abstract: This paper focuses on issues of engagement by staff in professional development related to the delivery of e-learning. The paper reports on findings drawn from a New Zealand research project which is producing a sector-wide framework for professional development in tertiary e-learning. The research findings indicate that staff engaged in e-learning in tertiary institutions is not making the most effective use of the professional development opportunities available to them; rather they seem to gain their knowledge and support from a variety of informal means. This is despite an emphasis on the provision of professional development opportunities by both Government Policies and Institutions themselves. The conclusion drawn from the findings is that institutional approaches to professional development for e-learning do not yet fully reflect the demands and constraints that working in a digital context impose.
Abstract: In this paper, we propose a practical digital music matching system that is robust to variation in sound qualities. The proposed system is subdivided into two parts: client and server. The client part consists of the input, preprocessing and feature extraction modules. The preprocessing module, including the music onset module, revises the value gap occurring on the time axis between identical songs of different formats. The proposed method uses delta-grouped Mel frequency cepstral coefficients (MFCCs) to extract music features that are robust to changes in sound quality. According to the number of sound quality formats (SQFs) used, a music server is constructed with a feature database (FD) that contains different sub feature databases (SFDs). When the proposed system receives a music file, the selection module selects an appropriate SFD from a feature database; the selected SFD is subsequently used by the matching module. In this study, we used 3,000 queries for matching experiments in three cases with different FDs. In each case, we used 1,000 queries constructed by mixing 8 SQFs and 125 songs. The success rate of music matching improved from 88.6% when using single a single SFD to 93.2% when using quadruple SFDs. By this experiment, we proved that the proposed method is robust to various sound qualities.
Abstract: Carrier mobility has become the most important
characteristic of high speed low dimensional devices. Due to
development of very fast switching semiconductor devices, speed of
computer and communication equipment has been increasing day by
day and will continue to do so in future. As the response of any
device depends on the carrier motion within the devices, extensive
studies of carrier mobility in the devices has been established
essential for the growth in the field of low dimensional devices.
Small-signal ac transport of degenerate two-dimensional hot
electrons in GaAs quantum wells is studied here incorporating
deformation potential acoustic, polar optic and ionized impurity
scattering in the framework of heated drifted Fermi-Dirac carrier
distribution. Delta doping is considered in the calculations to
investigate the effects of double delta doping on millimeter and submillimeter
wave response of two dimensional hot electrons in GaAs
nanostructures. The inclusion of delta doping is found to enhance
considerably the two dimensional electron density which in turn
improves the carrier mobility (both ac and dc) values in the GaAs
quantum wells thereby providing scope of getting higher speed
devices in future.
Abstract: Quality costs are the costs associated with preventing,
finding, and correcting defective work. Since the main language of
corporate management is money, quality-related costs act as means of
communication between the staff of quality engineering departments
and the company managers. The objective of quality engineering is to
minimize the total quality cost across the life of product. Quality
costs provide a benchmark against which improvement can be
measured over time. It provides a rupee-based report on quality
improvement efforts. It is an effective tool to identify, prioritize and
select quality improvement projects. After reviewing through the
literature it was noticed that a simplified methodology for data
collection of quality cost in a manufacturing industry was required.
The quantified standard methodology is proposed for collecting data
of various elements of quality cost categories for manufacturing
industry. Also in the light of research carried out so far, it is felt
necessary to standardise cost elements in each of the prevention,
appraisal, internal failure and external failure costs. . Here an attempt
is made to standardise the various cost elements applicable to
manufacturing industry and data is collected by using the proposed
quantified methodology. This paper discusses the case study carried
in luggage manufacturing industry.
Abstract: This paper establishes some closed formulas for
Riemann- Liouville impulsive fractional integral calculus and also
for Riemann- Liouville and Caputo impulsive fractional
derivatives.
Abstract: In this work, we present an automatic vehicle detection
system for airborne videos using combined features. We propose a
pixel-wise classification method for vehicle detection using Dynamic
Bayesian Networks. In spite of performing pixel-wise classification,
relations among neighboring pixels in a region are preserved in the
feature extraction process. The main novelty of the detection scheme is
that the extracted combined features comprise not only pixel-level
information but also region-level information. Afterwards, tracking is
performed on the detected vehicles. Tracking is performed using
efficient Kalman filter with dynamic particle sampling. Experiments
were conducted on a wide variety of airborne videos. We do not
assume prior information of camera heights, orientation, and target
object sizes in the proposed framework. The results demonstrate
flexibility and good generalization abilities of the proposed method on
a challenging dataset.
Abstract: In this research work, poly (acrylonitrile-butadienestyrene)/
polypropylene (ABS/PP) blends were processed by melt
compounding in a twin-screw extruder. Upgrading of the thermal
characteristics of the obtained materials was attempted by the
incorporation of organically modified montmorillonite (OMMT), as
well as, by the addition of two types of compatibilizers;
polypropylene grafted with maleic anhydride (PP-g-MAH) and ABS
grafted with maleic anhydride (ABS-g-MAH). The effect of the
above treatments was investigated separately and in combination.
Increasing the PP content in ABS matrix seems to increase the
thermal stability of their blend and the glass transition temperature
(Tg) of SAN phase of ABS. From the other part, the addition of ABS
to PP promotes the formation of its β-phase, which is maximum at 30
wt% ABS concentration, and increases the crystallization temperature
(Tc) of PP. In addition, it increases the crystallization rate of PP.The
β-phase of PP in ABS/PP blends is reduced by the addition of
compatibilizers or/and organoclay reinforcement. The incorporation
of compatibilizers increases the thermal stability of PP and reduces
its melting (ΔΗm) and crystallization (ΔΗc) enthalpies. Furthermore it
decreases slightly the Tgs of PP and SAN phases of ABS/PP blends.
Regarding the storage modulus of the ABS/PP blends, it presents a
change in their behavior at about 10°C and return to their initial
behavior at ~110°C. The incorporation of OMMT to no compatibilized
and compatibilized ABS/PP blends enhances their storage modulus.
Abstract: Robustness is one of the primary performance criteria for an Intelligent Video Surveillance (IVS) system. One of the key factors in enhancing the robustness of dynamic video analysis is,providing accurate and reliable means for shadow detection. If left undetected, shadow pixels may result in incorrect object tracking and classification, as it tends to distort localization and measurement information. Most of the algorithms proposed in literature are computationally expensive; some to the extent of equalling computational requirement of motion detection. In this paper, the homogeneity property of shadows is explored in a novel way for shadow detection. An adaptive division image (which highlights homogeneity property of shadows) analysis followed by a relatively simpler projection histogram analysis for penumbra suppression is the key novelty in our approach.
Abstract: The objective of the present work is to conduct
investigations leading to a more complete explanation of single phase
natural convective heat transfer in an enclosure with fin utilizing
nano fluids. The nano fluid used, which is composed of Aluminum
oxide nano particles in suspension of Ethylene glycol, is provided at
various volume fractions. The study is carried out numerically for a
range of Rayleigh numbers, fin heights and aspect ratio. The flow and
temperature distributions are taken to be two-dimensional. Regions
with the same velocity and temperature distributions are identified as
symmetry of sections. One half of such a rectangular region is chosen
as the computational domain taking into account the symmetry about
the fin. Transport equations are modeled by a stream functionvorticity
formulation and are solved numerically by finite-difference
schemes. Comparisons with previously published works on the basis
of special cases are done. Results are presented in the form of
streamline, vector and isotherm plots as well as the variation of local
Nusselt number along the fin under different conditions.
Abstract: Polymer melt compressibility and mold surface roughness, which are generally ignored during the filling stage of the conventional injection molding, may become increasingly significant in micro injection molding where the parts become smaller. By employing the 2.5D generalized Hele-Shaw model, we presented here the effects of polymer compressibility and mold surface roughness on mold-filling in a micro-thickness cavity. To elucidate the effects of surface roughness, numerical investigations were conducted using a cavity flat plate which has two halves with different surface roughness. This allows the comparison of flow field on two different halves under identical processing conditions but with different roughness. Results show that polymer compressibility and mold surface roughness have effects on mold filling in micro injection molding. There is in shrinkage reduction as the density is increased due to polymer melt compressibility during the filling stage.
Abstract: The demand for new telecommunication services requiring higher capacities, data rates and different operating modes have motivated the development of new generation multi-standard wireless transceivers. A multi-standard design often involves extensive system level analysis and architectural partitioning, typically requiring extensive calculations. In this research, a decimation filter design tool for wireless communication standards consisting of GSM, WCDMA, WLANa, WLANb, WLANg and WiMAX is developed in MATLAB® using GUIDE environment for visual analysis. The user can select a required wireless communication standard, and obtain the corresponding multistage decimation filter implementation using this toolbox. The toolbox helps the user or design engineer to perform a quick design and analysis of decimation filter for multiple standards without doing extensive calculation of the underlying methods.
Abstract: The design of high-rise building is more often dictated
by its serviceability rather than strength. Structural Engineers are
always striving to overcome challenge of controlling lateral
deflection and storey drifts as well as self weight of structure
imposed on foundation.
One of the most effective techniques is the use of outrigger and
belt truss system in Composite structures that can astutely solve the
above two issues in High-rise constructions.
This paper investigates deflection control by effective utilisation
of belt truss and outrigger system on a 60-storey composite building
subjected to wind loads. A three dimensional Finite Element Analysis
is performed with one, two and three outrigger levels. The reductions
in lateral deflection are 34%, 42% and 51% respectively as compared
to a model without any outrigger system. There is an appreciable
decline in the storey drifts with the introduction of these stiffer
arrangements.
Abstract: A new hybrid coding method for compressing
animated polygonal meshes is presented. This paper assumes
the simplistic representation of the geometric data: a temporal
sequence of polygonal meshes for each discrete frame of the
animated sequence. The method utilizes a delta coding and an
octree-based method. In this hybrid method, both the octree
approach and the delta coding approach are applied to each
single frame in the animation sequence in parallel. The
approach that generates the smaller encoded file size is chosen
to encode the current frame. Given the same quality
requirement, the hybrid coding method can achieve much
higher compression ratio than the octree-only method or the
delta-only method. The hybrid approach can represent 3D
animated sequences with higher compression factors while
maintaining reasonable quality. It is easy to implement and have
a low cost encoding process and a fast decoding process, which
make it a better choice for real time application.
Abstract: The paper presents the results of microhardness and
microstructure of low carbon steel surface melted using carbon
dioxide laser with a wavelength of 10.6μm and a maximum output
power of 2000W. The processing parameters such as the laser power,
and the scanning rate were investigated in this study. After surface
melting two distinct regions formed corresponding to the melted zone
MZ, and the heat affected zone HAZ. The laser melted region
displayed a cellular fine structures while the HAZ displayed
martensite or bainite structure. At different processing parameters,
the original microstructure of this steel (Ferrite+Pearlite) has been
transformed to new phases of martensitic and bainitic structures. The
fine structure and the high microhardness are evidence of the high
cooling rates which follow the laser melting. The melting pool and
the transformed microstructure in the laser surface melted region of
carbon steel showed clear dependence on laser power and scanning
rate.
Abstract: In this paper three different approaches for person
verification and identification, i.e. by means of fingerprints, face and
voice recognition, are studied. Face recognition uses parts-based
representation methods and a manifold learning approach. The
assessment criterion is recognition accuracy. The techniques under
investigation are: a) Local Non-negative Matrix Factorization
(LNMF); b) Independent Components Analysis (ICA); c) NMF with
sparse constraints (NMFsc); d) Locality Preserving Projections
(Laplacianfaces). Fingerprint detection was approached by classical
minutiae (small graphical patterns) matching through image
segmentation by using a structural approach and a neural network as
decision block. As to voice / speaker recognition, melodic cepstral
and delta delta mel cepstral analysis were used as main methods, in
order to construct a supervised speaker-dependent voice recognition
system. The final decision (e.g. “accept-reject" for a verification
task) is taken by using a majority voting technique applied to the
three biometrics. The preliminary results, obtained for medium
databases of fingerprints, faces and voice recordings, indicate the
feasibility of our study and an overall recognition precision (about
92%) permitting the utilization of our system for a future complex
biometric card.
Abstract: The move towards internationalization of accounting encountered a great boost, when in 2002 EU delegated the IASB to provide the accounting standards to be applied inside its frontiers. Among the incentives of the standardization of accounting on the international level, is the reduction of the cost of capital. Romania made the move towards IFRS before EU, when the country was not yet a member of it. Even if this made Romania a special case, it was scarcely approached. The leak of real data is usually the reason for avoiding. The novelty of this paper is that it offers an insight from the reality of Romanian companies and their view regarding the IFRS. The paper is based on a survey that the authors made among the companies listed on the first two tiers of the Bucharest Stock Exchange (BSE), which are basically, the most important companies in the country.