Abstract: In this paper we proposed the use of Huffman
coding to reduce the PAR of an OFDM system as a distortionless
scrambling technique, and we utilize the amount saved in the
total bit rate by the Huffman coding to send the encoding table
for accurate decoding at the receiver without reducing the
effective throughput. We found that the use of Huffman coding
reduces the PAR by about 6 dB. Also we have investigated the
effect of PAR reduction due to Huffman coding through testing
the spectral spreading and the inband distortion due to HPA with
different IBO values. We found a complete match of our
expectation from the proposed solution with the obtained
simulation results.
Abstract: Gas condensate Reservoirs show complicated thermodynamic behavior when their pressure reduces to under dew point pressure. Condensate blockage around the producing well cause significant reduction of production rate as well bottom-hole pressure drops below saturation pressure. The main objective of this work was to examine the well test analysis of naturally fractured lean gas condensate reservoir and investigate the effect of condensate formed around the well-bore on behavior of single phase pseudo pressure and its derivative curves. In this work a naturally fractured lean gas condensate reservoir is simulated with compositional simulator. Different sensitivity analysis done on Corry parameters and result of simulator is feed to analytical well testing software. For consideration of these phenomena eighteen compositional models with Capillary number effect are constructed. Matrix relative permeability obeys Corry relative permeability and relative permeability in fracture is linear. Well testing behavior of these models are studied and interpreted. Results show different sensitivity analysis on relative permeability of matrix does not have strong effect on well testing behavior even most part of the matrix around the well is occupied with condensate.
Abstract: Simulation and modeling computer programs are
concerned with construction of models for analyzing different
perspectives and possibilities in changing conditions environment.
The paper presents theoretical justification and evaluation of
qualitative e-learning development model in perspective of advancing
modern technologies. There have been analyzed principles of
qualitative e-learning in higher education, productivity of studying
process using modern technologies, different kind of methods and
future perspectives of e-learning in formal education. Theoretically
grounded and practically tested model of developing e-learning
methods using different technologies for different type of classroom,
which can be used in professor-s decision making process to choose
the most effective e-learning methods has been worked out.
Abstract: This paper explains the cause of nonlinearity in floor
attenuation hither to left unexplained. The performance degradation
occurring in air interface for GSM signals is quantitatively analysed
using the concept of Radiating Columns of buildings. The signal
levels were measured using Wireless Network Optimising Drive Test
Tool (E6474A of Agilent Technologies). The measurements were
taken in reflected signal environment under usual fading conditions
on actual GSM signals radiated from base stations. A mathematical
model is derived from the measurements to predict the GSM signal
levels in different floors. It was applied on three buildings and found
that the predicted signal levels deviated from the measured levels
with in +/- 2 dB for all floors. It is more accurate than the prediction
models based on Floor Attenuation Factor. It can be used for
planning proper indoor coverage in multi storey buildings.
Abstract: The paper addresses a problem of optimal staffing in
open shop environment. The problem is to determine the optimal
number of operators serving a given number of machines to fulfill the
number of independent operations while minimizing staff idle. Using
a Gantt chart presentation of the problem it is modeled as twodimensional
cutting stock problem. A mixed-integer programming
model is used to get minimal job processing time (makespan) for
fixed number of machines' operators. An algorithm for optimal openshop
staffing is developed based on iterative solving of the
formulated optimization task. The execution of the developed
algorithm provides optimal number of machines' operators in the
sense of minimum staff idle and optimal makespan for that number of
operators. The proposed algorithm is tested numerically for a real life
staffing problem. The testing results show the practical applicability
for similar open shop staffing problems.
Abstract: The localization of software products is essential for reaching the users of the international market. An important task for this is the translation of the user interface into local national languages. As graphical interfaces are usually optimized for the size of the texts in the original language, after the translation certain user controls (e.g. text labels and buttons in dialogs) may grow in such a manner that they slip above each other. This not only causes an unpleasant appearance but also makes the use of the program more difficult (or even impossible) which implies that the arrangement of the controls must be corrected subsequently. The correction should preserve the original structure of the interface (e.g. the relation of logically coherent controls), furthermore, it is important to keep the nicely proportioned design: the formation of large empty areas should be avoided. This paper describes an algorithm that automatically rearranges the controls of a graphical user interface based on the principles above. The algorithm has been implemented and integrated into a translation support system and reached results pleasant for the human eye in most test cases.
Abstract: This paper proposes a method to improve the shortest
path problem on a NURBS (Non-uniform rational basis spline) surfaces.
It comes from an application of the theory in classic differential
geometry on surfaces and can improve the distance problem not only
on surfaces but in the Euclidean 3-space R3 .
Abstract: In this paper, a new alignment method based on the particle swarm optimization (PSO) technique is presented. The PSO algorithm is used for locating the optimal coupling position with the highest optical power with three-degrees of freedom alignment. This algorithm gives an interesting results without a need to go thru the complex mathematical modeling of the alignment system. The proposed algorithm is validated considering practical tests considering the alignment of two Single Mode Fibers (SMF) and the alignment of SMF and PCF fibers.
Abstract: The aim of the article is extending and developing
econometrics and network structure based methods which are able to
distinguish price manipulation in Tehran stock exchange. The
principal goal of the present study is to offer model for
approximating price manipulation in Tehran stock exchange. In order
to do so by applying separation method a sample consisting of 397
companies accepted at Tehran stock exchange were selected and
information related to their price and volume of trades during years
2001 until 2009 were collected and then through performing runs
test, skewness test and duration correlative test the selected
companies were divided into 2 sets of manipulated and non
manipulated companies. In the next stage by investigating
cumulative return process and volume of trades in manipulated
companies, the date of starting price manipulation was specified and
in this way the logit model, artificial neural network, multiple
discriminant analysis and by using information related to size of
company, clarity of information, ratio of P/E and liquidity of stock
one year prior price manipulation; a model for forecasting price
manipulation of stocks of companies present in Tehran stock
exchange were designed. At the end the power of forecasting models
were studied by using data of test set. Whereas the power of
forecasting logit model for test set was 92.1%, for artificial neural
network was 94.1% and multi audit analysis model was 90.2%;
therefore all of the 3 aforesaid models has high power to forecast
price manipulation and there is no considerable difference among
forecasting power of these 3 models.
Abstract: Potassium monopersulfate has been decomposed in
aqueous solution in the presence of Co(II). The effect of the main
operating variables has been assessed. Minimum variations in pH
exert a considerable influence on the process kinetics. Thus, when no
pH adjustment is considered, the actual effect of variables like initial
monopersulfate and/or catalyst concentration may be hindered. As
expected, temperature enhances the monopersulfate decomposition
rate by following the Arrhenius law. The activation energy in the
proximity of 85 kJ/mol has been obtained. Amongst the different
solids tested in the monopersulfate decomposition, only the
perovskite LaTi0.15Cu0.85O3 has shown a significant catalytic activity.
Abstract: In this research relationship between to be smooth the
interest and output of accepted companies stock at negotiable paper
exchange of Tehran is studied. Static community capacity included
363 companies member of negotiable paper exchange of Tehran that
54 companies were, by considering research limitation, selected from
2004 to 2009. Needed data for model test in librarian method was
chosen from RAH AVARDE NOVIN informative banks, TADBIR
and collecting needed data was selected from Tehran negotiable
paper exchange archive. Given results show that in spite of belief
among people based on companies have more smooth interest have
more output, but resulted outcomes of test-done reveals that there is
no relation between smooth interest and stock output.
Abstract: The estrus female Etawah cross bred goats were
synchronized estrus by controlled internal drug release (CIDR)
implants for 10 days combined with PGF2α injection, and continued
by artificial insemination (AI) within the hours of 24 period. Vaginal
epithelium was taken to determine estrus cycle of the goats without
estrus synchronization. The estrus responds (the puffy of vulva and
vaginal pH) and percentage of pregnancy were investigated. The data
were analyzed descriptively and Independent Sample T-Test. The
results showed that the puffy of vulva and vaginal pH were
significantly different in synchronized estrus goats and control goats
(2.18 ± 0.33 cm vs. 1.20 ± 0.16 cm and 8.55 ± 0.63 vs. 8.22 ± 0.22).
Percentage of pregnancy was higher in synchronized estrus goats
(73.33%) than in control (53.3%). Estrus synchronization by using
CIDR implants and PGF2, continued by AI was effective to improve
reproduction performance of Etawah cross bred goats.
Abstract: The purpose of this study is to examine the selfefficacy
and life satisfaction levels of students receiving education in
schools of physical education and sports. The population of the study
consisted 263 students, among which 154 were male and 109 were
female ( X age=19,4905 + 2,5605), that received education in the
schools of physical education and sports of Selcuk University, Inonu
University, Gazi University and Karamanoglu Mehmetbey
University. In order to achieve the purpose of the study, the selfefficacy
scale, which was developed by Jarrusselam and Shwarzer
(1981) [1] and adapted to Turkish by Yesillay (1993) [2], and the
life satisfaction scale, developed by Diener, Emmos, Larsen and
Griffin (1985) [3] and adapted to Turkish by Kokler (1991) [4], were
utilized.For analyzing and interpreting data Kolmogorov-Smirnov
test, t-test and one way anova test were used, while for determining
the difference between the groups Tukey test and Multiple Linear
Regression test were employed and significance was accepted at
P
Abstract: Foodborne Salmonella infections have become a
major problem world wide. Salmonellosis transmitted from fish are
quite common. Established quality control measures exist for export
oriented fish, none exists for fish consumed locally. This study aimed
at characterization of Salmonella isolated from Nile tilapia . The
study was carried out in selected beaches along L. Victoria in
Western Kenya between March and June 2007. One hundred and
twenty fish specimens were collected. Salmonella isolates were
confirmed using serotyping, biochemical testing in addition to malic
acid dehydrogenase (mdh) and fliC gene sequencing. Twenty
Salmonella isolates were confirmed by mdh gene sequencing. Nine
(9) were S. enterica serotype typhimurium, four (4) were S. enterica
Serotype, enteritidis and seven (7) were S. enterica serotype typhi.
Nile tilapia have a role in transmission of Salmonellosis in the study
area, poor sanitation was a major cause of pollution at the beach
inshore waters.
Abstract: The aim of this work is to investigate on the internalflow
patterns in a plate heat exchanger channel, which affect the
rate of sedimentation fouling on the heat transfer surface of the
plate heat exchanger. The research methodologies were the
computer simulation using Computational Fluid Dynamics (CFD)
and the experimental works. COMSOL MULTIPHYSICS™
Version 3.3 was used to simulate the velocity flow fields to verify
the low and high flow regions. The results from the CFD technique
were then compared with the images obtained from the
experiments in which the fouling test rig was set up with a singlechannel
plate heat exchanger to monitor the fouling of calcium
carbonate. Two parameters were varied i.e., the crossing angle of
the two plate: 55/55, 10/10, and 55/10 degree, and the fluid flow
rate at the inlet: 0.0566, 0.1132 and 0.1698 m/s. The type of plate
“GX-12" (the surface area 0.12 m2, the depth 2.9 mm, the width of
fluid flow 215 mm and the thickness of stainless plate of 0.5 mm)
was used in this study. The results indicated that the velocity
distribution for the case of 55/55 degree seems to be very well
organized when compared with the others. Also, an increase in the
inlet velocity resulted in the reduction of fouling rate on the surface
of plate heat exchangers.
Abstract: Due to their high power-to-weight ratio and low cost, pneumatic actuators are attractive for robotics and automation applications; however, achieving fast and accurate control of their position have been known as a complex control problem. The paper presents a methodology for obtaining controllers that achieve high position accuracy and preserve the closed-loop characteristics over a broad operating range. Experimentation with a number of conventional (or "classical") three-term controllers shows that, as repeated operations accumulate, the characteristics of the pneumatic actuator change requiring frequent re-tuning of the controller parameters (PID gains). Furthermore, three-term controllers are found to perform poorly in recovering the closed-loop system after the application of load or other external disturbances. The key reason for these problems lies in the non-linear exchange of energy inside the cylinder relating, in particular, to the complex friction forces that develop on the piston-wall interface. In order to overcome this problem but still remain within the boundaries of classical control methods, we designed an auto selective classicaql controller so that the system performance would benefit from all three control gains (KP, Kd, Ki) according to system requirements and the characteristics of each type of controller. This challenging experimentation took place for consistent performance in the face of modelling imprecision and disturbances. In the work presented, a selective PID controller is presented for an experimental rig comprising an air cylinder driven by a variable-opening pneumatic valve and equipped with position and pressure sensors. The paper reports on tests carried out to investigate the capability of this specific controller to achieve consistent control performance under, repeated operations and other changes in operating conditions.
Abstract: In an electric power system, spinning reserve
requirements can be determined by using deterministic and/or
probabilistic measures. Although deterministic methods are usual in
many systems, application of probabilistic methods becomes
increasingly important in the new environment of the electric power
utility industry. This is because of the increased uncertainty
associated with competition. In this paper 1) a new probabilistic
method is presented which considers the reliability of transmission
system in a simplified manner and 2) deterministic and probabilistic
methods are compared. The studied methods are applied to the Roy
Billinton Test System (RBTS).
Abstract: Many metrics were proposed to evaluate the
characteristics of the analysis and design model of a given product
which in turn help to assess the quality of the product. Function point
metric is a measure of the 'functionality' delivery by the software.
This paper presents an analysis of a set of programs of a project
developed in Cµ through Function Points metric. Function points
are measured for a Data Flow Diagram (DFD) of the case developed
at initial stage. Lines of Codes (LOCs) and possible errors are
calculated with the help of measured Function Points (FPs). The
calculations are performed using suitable established functions.
Calculated LOCs and errors are compared with actual LOCs and
errors found at the time of analysis & design review, implementation
and testing. It has been observed that actual found errors are more
than calculated errors. On the basis of analysis and observations,
authors conclude that function point provides useful insight and helps
to analyze the drawbacks in the development process.
Abstract: Transient Stability is an important issue in power systems planning, operation and extension. The objective of transient stability analysis problem is not satisfied with mere transient instability detection or evaluation and it is most important to complement it by defining fast and efficient control measures in order to ensure system security. This paper presents a new Fuzzy Support Vector Machines (FSVM) to investigate the stability status of power systems and a modified generation rescheduling scheme to bring back the identified unstable cases to a more economical and stable operating point. FSVM improves the traditional SVM (Support Vector Machines) by adding fuzzy membership to each training sample to indicate the degree of membership of this sample to different classes. The preventive control based on economic generator rescheduling avoids the instability of the power systems with minimum change in operating cost under disturbed conditions. Numerical results on the New England 39 bus test system show the effectiveness of the proposed method.
Abstract: In intensity modulated radiation therapy (IMRT)
treatment planning, beam angles are usually preselected on the basis of
experience and intuition. Therefore, getting an appropriate beam
configuration needs a very long time. Based on the present situation,
the paper puts forward beam orientation optimization using ant colony
optimization (ACO). We use ant colony optimization to select the
beam configurations, after getting the beam configuration using
Conjugate Gradient (CG) algorithm to optimize the intensity profiles.
Combining with the information of the effect of pencil beam, we can
get the global optimal solution accelerating. In order to verify the
feasibility of the presented method, a simulated and clinical case was
tested, compared with dose-volume histogram and isodose line
between target area and organ at risk. The results showed that the
effect was improved after optimizing beam configurations. The
optimization approach could make treatment planning meet clinical
requirements more efficiently, so it had extensive application
perspective.