Abstract: TiO2 supported nano-ZnO catalyst was prepared by
deposition-precipitation and tested for the trans-esterification
reaction of soybean oil to biodiesel. The TiO2 support stabilized the
nano-ZnO in a dispersed form with limited crystallite size compared
to the unsupported ZnO. The final ZnO dispersion and crystallite size
and the material transfer resistance in the catalyst significantly
influenced the supported nano-ZnO catalyst performance.
Abstract: An electronic portal image device (EPID) has become
a method of patient-specific IMRT dose verification for radiotherapy.
Research studies have focused on pre and post-treatment verification,
however, there are currently no interventional procedures using EPID
dosimetry that measure the dose in real time as a mechanism to
ensure that overdoses do not occur and underdoses are detected as
soon as is practically possible. As a result, an EPID-based real time
dose verification system for dynamic IMRT was developed and was
implemented with MATLAB/Simulink. The EPID image acquisition
was set to continuous acquisition mode at 1.4 images per second. The
system defined the time constraint gap, or execution gap at the image
acquisition time, so that every calculation must be completed before
the next image capture is completed. In addition, the
Abstract: In this present study, experimental work was
conducted to study the effectiveness of newly innovated steel-CFRP
composite (CFRP laminates sandwiched between two steel strips) as
stirrups. A total numbers of eight concrete beams were tested under
four point loads. Each beam measured 1600 mm long, 160mm width
and 240 mm depth. The beams were reinforced with different shear
reinforcements; one without stirrups, one with steel stirrups and six
with different types and numbers of steel-CRFR stirrups. Test results
indicated that the steel-CFRP stirrups had enhanced the shear
strength capacity of beams. Moreover, the tests revealed that steel-
CFRP stirrups reached to their ultimate tensile strength unlike FRP
stirrups which rupture at much lower level than their ultimate
strength as werereported in various researches.
Abstract: Tourism is a phenomenon respected by the human communities since a long time ago. It has been evoloving continually based on a variety of social and economic needs and with respect to increasingly development of communication and considerable increase of tourist-s number and resulted exchange income has attained much out come such as employment for the communities. or the purpose of tourism development in this zone suitable times and locations need to be specified in the zone for the tourist-s attendance. One of the most important needs of the tourists is the knowledge of climate conditions and suitable times for sightseeing. In this survey, the climate trend condition has been identified for attending the tourists in Isfahan province using the modified tourism climate index (TCI) as well as SPSS, GIS, excel, surfer softwares. This index evoluates systematically the climate conditions for tourism affairs and activities using the monthly maximum mean parameters of daily temperature, daily mean temperature, minimum relative humidity, daily mean relative humidity, precipitation (mm), total sunny hours, wind speed and dust. The results obtaind using kendal-s correlation test show that the months January, February, March, April, May, June, July, August, September, October, November and December are significant and have an increasing trend that indicates the best condition for attending the tourists. S, P, T mean , T max and dust are estimated from 1976-2005 and do kendal-s correlation test again to see which parameter has been effective. Based on the test, we also observed on the effective parameters that the rate of dust in February, March, April, May, June, July, August, October and November is decreasing and precipitation in September and January is increasing and also the radiation rate in May and August is increasing that indicate a better condition of convenience. Maximum temperature in June is also decreasing. Isfahan province has two spring and fall peaks and the best places for tourism are in the north and western areas.
Abstract: This paper describes a UDP over IP based, server-oriented redundant host configuration protocol (RHCP) that can be used by collaborating embedded systems in an ad-hoc network to acquire a dynamic IP address. The service is provided by a single network device at a time and will be dynamically reassigned to one of the other network clients if the primary provider fails. The protocol also allows all participating clients to monitor the dynamic makeup of the network over time. So far the algorithm has been implemented and tested on an 8-bit embedded system architecture with a 10Mbit Ethernet interface.
Abstract: This paper presents a review on published literature
and experimental works on local sands for possible use as proppant,
specifically those from Terengganu coastal area. This includes
examination on characteristics of sand samples and selection of
experiments for proppant testing. Sand samples from identified areas
were tested according to particle size distribution, density, roundness
and sphericity, turbidity and mineralogy. Results from sand samples
were compared against proppant specifications set by API RP 56 and
selected commercial proppants. The present study found that the size
distribution, sphericity, turbidity and bulk density of Terengganu
sands are at par with some of commercial proppants. Nevertheless,
Terengganu sand samples do not completely surpass the required
roundness for use as proppant.
Abstract: Developing a supply chain management (SCM) system is costly, but important. However, because of its complicated nature, not many of such projects are considered successful. Few research publications directly relate to key success factors (KSFs) for implementing a SCM system. Motivated by the above, this research proposes a hierarchy of KSFs for SCM system implementation in the semiconductor industry by using a two-step approach. First, the literature review indicates the initial hierarchy. The second step includes a focus group approach to finalize the proposed KSF hierarchy by extracting valuable experiences from executives and managers that actively participated in a project, which successfully establish a seamless SCM integration between the world's largest semiconductor foundry manufacturing company and the world's largest assembly and testing company. Future project executives may refer the resulting KSF hierarchy as a checklist for SCM system implementation in semiconductor or related industries.
Abstract: One of the most important causes of accidents is
driver fatigue. To reduce the accidental rate, the driver needs a
quick nap when feeling sleepy. Hence, searching for the minimum
time period of nap is a very challenging problem. The purpose of
this paper is twofold, i.e. to investigate the possible fastest time
period for nap and its relationship with stage 2 sleep, and to
develop an automatic stage 2 sleep detection and alarm device. The
experiment for this investigation is designed with 21 subjects. It
yields the result that waking up the subjects after getting into stage
2 sleep for 3-5 minutes can efficiently reduce the sleepiness.
Furthermore, the automatic stage 2 sleep detection and alarm
device yields the real-time detection accuracy of approximately
85% which is comparable with the commercial sleep lab system.
Abstract: This paper investigates experimentally and
analytically the torsion behavior of steel fibered high strength self
compacting concrete beams reinforced by GFRP bars. Steel fibered
high strength self compacting concrete (SFHSSCC) and GFRP bars
became in the recent decades a very important materials in the
structural engineering field. The use of GFRP bars to replace steel
bars has emerged as one of the many techniques put forward to
enhance the corrosion resistance of reinforced concrete structures.
High strength concrete and GFRP bars attract designers and
architects as it allows improving the durability as well as the esthetics
of a construction. One of the trends in SFHSSCC structures is to
provide their ductile behavior and additional goal is to limit
development and propagation of macro-cracks in the body of
SFHSSCC elements. SFHSSCC and GFRP bars are tough, improve
the workability, enhance the corrosion resistance of reinforced
concrete structures, and demonstrate high residual strengths after
appearance of the first crack. Experimental studies were carried out
to select effective fiber contents. Three types of volume fraction from
hooked shape steel fibers are used in this study, the hooked steel
fibers were evaluated in volume fractions ranging between 0.0%,
0.75% and 1.5%. The beams shape is chosen to create the required
forces (i.e. torsion and bending moments simultaneously) on the test
zone. A total of seven beams were tested, classified into three groups.
All beams, have 200cm length, cross section of 10×20cm,
longitudinal bottom reinforcement of 3
Abstract: For the first time since 1940 and presentation of
theodorson-s theory, distribution of thrust, torque and efficiency
along the blade of a counter rotating propeller axial fan was studied
with a novel method in this research. A constant chord, constant
pitch symmetric fan was investigated with Reynolds Stress
Turbulence method in this project and H.E.S. method was utilized to
obtain distribution profiles from C.F.D. tests outcome. C.F.D. test
results were validated by estimation from Playlic-s analytical method.
Final results proved ability of H.E.S. method to obtain distribution
profiles from C.F.D test results and demonstrated interesting facts
about effects of solidity and differences between distributions in front
and rear section.
Abstract: This paper presented the technique of robot control by event-related potentials (ERPs) of brain waves. Based on the proposed technique, severe physical disabilities can free browse outside world. A specific component of ERPs, N2P3, was found and used to control the movement of robot and the view of camera on the designed brain-computer interface (BCI). Users only required watching the stimuli of attended button on the BCI, the evoked potentials of brain waves of the target button, N2P3, had the greatest amplitude among all control buttons. An experimental scene had been constructed that the robot required walking to a specific position and move the view of camera to see the instruction of the mission, and then completed the task. Twelve volunteers participated in this experiment, and experimental results showed that the correct rate of BCI control achieved 80% and the average of execution time was 353 seconds for completing the mission. Four main contributions included in this research: (1) find an efficient component of ERPs, N2P3, for BCI control, (2) embed robot's viewpoint image into user interface for robot control, (3) design an experimental scene and conduct the experiment, and (4) evaluate the performance of the proposed system for assessing the practicability.
Abstract: Gesture recognition is a challenging task for extracting
meaningful gesture from continuous hand motion. In this paper, we propose an automatic system that recognizes isolated gesture,
in addition meaningful gesture from continuous hand motion for Arabic numbers from 0 to 9 in real-time based on Hidden Markov Models (HMM). In order to handle isolated gesture, HMM using
Ergodic, Left-Right (LR) and Left-Right Banded (LRB) topologies is applied over the discrete vector feature that is extracted from stereo
color image sequences. These topologies are considered to different
number of states ranging from 3 to 10. A new system is developed to recognize the meaningful gesture based on zero-codeword detection
with static velocity motion for continuous gesture. Therefore, the
LRB topology in conjunction with Baum-Welch (BW) algorithm for
training and forward algorithm with Viterbi path for testing presents the best performance. Experimental results show that the proposed system can successfully recognize isolated and meaningful gesture and achieve average rate recognition 98.6% and 94.29% respectively.
Abstract: Meshless Finite Element Methods, namely element-free Galerkin and point-interpolation method were implemented and tested concerning their applicability to typical engineering problems like electrical fields and structural mechanics. A class-structure was developed which allows a consistent implementation of these methods together with classical FEM in a common framework. Strengths and weaknesses of the methods under investigation are discussed. As a result of this work joint usage of meshless methods together with classical Finite Elements are recommended.
Abstract: The design of methods of the 20 K large dimension cold shield used for infrared radiation demarcating in space environment simulation test were introduced in this paper. The cold shield were cooled by five G-M cryocoolers , and the dimension of the cold shield is the largest in our country.Cold shield installation and distribution and compensator for contraction on cooling were introduced detailedly. The temperature distribution and cool-down time of cold shield surface were also calculated and analysed in this paper. The design of cold shield resolves the difficulty of compensator for contraction on cooling successfully. Test results show that the actual technical performance indicators of cold shield met and exceeded the design requirements.
Abstract: Iris localization is a very important approach in
biometric identification systems. Identification process usually is
implemented in three levels: iris localization, feature extraction, and
pattern matching finally. Accuracy of iris localization as the first step
affects all other levels and this shows the importance of iris
localization in an iris based biometric system. In this paper, we
consider Daugman iris localization method as a standard method,
propose a new method in this field and then analyze and compare the
results of them on a standard set of iris images. The proposed method
is based on the detection of circular edge of iris, and improved by
fuzzy circles and surface energy difference contexts. Implementation
of this method is so easy and compared to the other methods, have a
rather high accuracy and speed. Test results show that the accuracy of
our proposed method is about Daugman method and computation
speed of it is 10 times faster.
Abstract: This study aims at investigating the empirical
relationships between risk preference, internet preference, and
internet knowledge which are known as user characteristics, in
addition to perceived risk of the customers on the internet purchase
intention. In order to test the relationships between the variables of
model 174, a questionnaire was collected from the students with
previous online experience. For the purpose of data analysis,
confirmatory factor analysis (CFA) and structural equation model
(SEM) was used.
Test results show that the perceived risk affects the internet
purchase intention, and increase or decrease of perceived risk
influences the purchase intention when the customer does the internet
shopping. Other factors such as internet preference, knowledge of the
internet, and risk preference affect the internet purchase intention.
Abstract: The influence of humidity and low temperature on the α- amylase activity and isoenzyme composition of grains of different wheat varieties have been studied. The identified samples of varieties have significant difference in the level of enzyme induction under the impact of high humidity and low temperature. It is proposed to use this methodological approach for testing genotypes and wheat breeding lines for resistance to pre-harvest sprouting (PHS).
Abstract: In this paper, we present two new one-step iterative
methods based on Thiele-s continued fraction for solving nonlinear
equations. By applying the truncated Thiele-s continued fraction
twice, the iterative methods are obtained respectively. Analysis of
convergence shows that the new methods are fourth-order convergent.
Numerical tests verifying the theory are given and based on the
methods, two new one-step iterations are developed.
Abstract: The scale dependence of the strength of virtually homogeneous rock is usually considered to be insignificant but the spectrum of discontinuities plays a very important role for the strength of differently sized rock elements and also controls the rock creep strain. Large-scale load tests comprised recording of the creep strain rate that was found to be strongly retarded and negligible for stresses lower than about 1/3 of the failure load. For higher stresses creep took place according to a log time law representing secondary creep that ultimately changed to tertiary creep and failure.
Abstract: Psoriasis is a widespread skin disease affecting up to 2% population with plaque psoriasis accounting to about 80%. It can be identified as a red lesion and for the higher severity the lesion is usually covered with rough scale. Psoriasis Area Severity Index (PASI) scoring is the gold standard method for measuring psoriasis severity. Scaliness is one of PASI parameter that needs to be quantified in PASI scoring. Surface roughness of lesion can be used as a scaliness feature, since existing scale on lesion surface makes the lesion rougher. The dermatologist usually assesses the severity through their tactile sense, therefore direct contact between doctor and patient is required. The problem is the doctor may not assess the lesion objectively. In this paper, a digital image analysis technique is developed to objectively determine the scaliness of the psoriasis lesion and provide the PASI scaliness score. Psoriasis lesion is modelled by a rough surface. The rough surface is created by superimposing a smooth average (curve) surface with a triangular waveform. For roughness determination, a polynomial surface fitting is used to estimate average surface followed by a subtraction between rough and average surface to give elevation surface (surface deviations). Roughness index is calculated by using average roughness equation to the height map matrix. The roughness algorithm has been tested to 444 lesion models. From roughness validation result, only 6 models can not be accepted (percentage error is greater than 10%). These errors occur due the scanned image quality. Roughness algorithm is validated for roughness measurement on abrasive papers at flat surface. The Pearson-s correlation coefficient of grade value (G) of abrasive paper and Ra is -0.9488, its shows there is a strong relation between G and Ra. The algorithm needs to be improved by surface filtering, especially to overcome a problem with noisy data.