Abstract: The nutritional composition and hypoglycaemic effect
of crackers produced from blend of sprouted pigeon pea, unripe
plantain and brewers’ spent grain and fed to Alloxan induced diabetic
rat was investigated. Crackers were produced from different blends of
sprouted pigeon pea, unripe plantain and brewers’ spent grain. The
crackers were evaluated for proximate composition, amino acid
profile and antinutritional factors. Blood glucose levels of normal and
diabetic rats fed with the control sample and different formulations of
cracker were measured. The protein content of the samples were
significantly different (p
Abstract: This research work is an experimental study, through
development of an adhesive from Prosopis africana endosperm. The
prosopis seed for this work were obtained from Enugu State in the
South East part of Nigeria. The seeds were prepared by separating the
endosperm from the seed coat and cotyledon. Three methods were
used to separate them, which are acidic method, roasting method and
boiling method. 20g of seed were treated with different
concentrations (25, 40, 55, 70, and 85% w/w) at 100°C and constant
time (30 minutes), under continuous stirring with magnetic stirrer.
Also 20g of seed were treated with sulphuric acid of concentrations
40% w/w at 100°C with different time (10, 15, 20, 25, 30 minutes),
under continuous stirring with magnetic stirrer. Finally, 20g of seed
were treated with sulphuric acid of concentrations 40% w/w at
different temperature (20°C, 40°C, 60°C, 80°C, and 100°C) with
constant time (30 minutes), under continuous stirring with magnetic
stirrer. The whole endosperm extracted was adhesive. The physical
properties of the adhesive were determined (appearance, odour, taste,
solubility, pH, size, and binding strength). The percentage of the
adhesive yield makes the commercialization of the seed in Nigeria
possible and profitable. The very high viscosity attained at low
concentrations makes prosopis adhesive an excellent thickener in the
food industry.
Abstract: Journal bearings used in IC engines are prone to premature
failures and are likely to fail earlier than the rated life due to
highly impulsive and unstable operating conditions and frequent
starts/stops. Vibration signature extraction and wear debris analysis
techniques are prevalent in industry for condition monitoring of
rotary machinery. However, both techniques involve a great deal of
technical expertise, time, and cost. Limited literature is available on
the application of these techniques for fault detection in reciprocating
machinery, due to the complex nature of impact forces that
confounds the extraction of fault signals for vibration-based analysis
and wear prediction. In present study, a simulation model was developed to investigate
the bearing wear behaviour, resulting because of different operating
conditions, to complement the vibration analysis. In current
simulation, the dynamics of the engine was established first, based on
which the hydrodynamic journal bearing forces were evaluated by
numerical solution of the Reynold’s equation. In addition, the
essential outputs of interest in this study, critical to determine wear
rates are the tangential velocity and oil film thickness between the
journals and bearing sleeve, which if not maintained appropriately,
have a detrimental effect on the bearing performance. Archard’s wear prediction model was used in the simulation to
calculate the wear rate of bearings with specific location information
as all determinative parameters were obtained with reference to crank
rotation. Oil film thickness obtained from the model was used as a
criterion to determine if the lubrication is sufficient to prevent contact
between the journal and bearing thus causing accelerated wear. A
limiting value of 1 μm was used as the minimum oil film thickness
needed to prevent contact. The increased wear rate with growing
severity of operating conditions is analogous and comparable to the
rise in amplitude of the squared envelope of the referenced vibration
signals. Thus on one hand, the developed model demonstrated its
capability to explain wear behaviour and on the other hand it also
helps to establish a co-relation between wear based and vibration
based analysis. Therefore, the model provides a cost effective and
quick approach to predict the impending wear in IC engine bearings
under various operating conditions.
Abstract: Bottom ash from Municipal Solid Waste Incineration
(MSWI) can be viewed as a typical granular material because these
industrial by-products result from the incineration of various
domestic wastes. MSWI bottom ash is mainly used in road
engineering in substitution of the traditional natural aggregates. As
the characterization of their mechanical behavior is essential in order
to use them, specific studies have been led over the past few years. In
the first part of this paper, the mechanical behavior of MSWI bottom
ash is studied with triaxial tests. After, analysis of the experiment
results, the simulation of triaxial tests is carried out by using the
software package CESAR-LCPC. As the first approach in modeling
of this new class material, the Mohr-Coulomb model was chosen to
describe the evolution of material under the influence of external
mechanical actions.
Abstract: The paper presents a method in which the expert
knowledge is applied to fuzzy inference model. Even a less
experienced person could benefit from the use of such a system, e.g.
urban planners, officials. The analysis result is obtained in a very
short time, so a large number of the proposed locations can also be
verified in a short time. The proposed method is intended for testing
of locations of car parks in a city. The paper shows selected examples
of locations of the P&R facilities in cities planning to introduce the
P&R. The analyses of existing objects are also shown in the paper
and they are confronted with the opinions of the system users, with
particular emphasis on unpopular locations. The results of the
analyses are compared to expert analysis of the P&R facilities
location that was outsourced by the city and the opinions about
existing facilities users that were expressed on social networking
sites. The obtained results are consistent with actual users’ feedback.
The proposed method proves to be good, but does not require the
involvement of a large experts team and large financial contributions
for complicated research. The method also provides an opportunity to
show the alternative location of P&R facilities. Although the results
of the method are approximate, they are not worse than results of
analysis of employed experts. The advantage of this method is ease of
use, which simplifies the professional expert analysis. The ability of
analyzing a large number of alternative locations gives a broader
view on the problem. It is valuable that the arduous analysis of the
team of people can be replaced by the model's calculation. According
to the authors, the proposed method is also suitable for
implementation on a GIS platform.
Abstract: Searching the “Island of stability” is a topic of
extreme interest in theoretical as well as experimental modern
physics today. This “island of stability” is spanned by superheavy
elements (SHE's) that are produced in the laboratory. SHE's are
believed to exist primarily due to the “magic” stabilizing effects of
nuclear shell structure. SHE synthesis is extremely difficult due to
their very low production cross section, often of the order of pico
barns or less. Stabilizing effects of shell closures at proton number
Z=82 and neutron number N=126 are predicted theoretically. Though
stabilizing effects of Z=82 have been experimentally verified, no
concluding observations have been made with N=126, so far. We
measured and analyzed the total evaporation residue (ER) cross
sections for a number of systems with neutron number around 126 to
explore possible shell closure effects in ER cross sections, in this
work.
Abstract: In India, most of the pavement is laid by bituminous
road and the consumption of binder is high for pavement construction
and also modified binders are used to satisfy any specific pavement
requirement. Since the binders are visco-elastic material which is
having the mechanical properties of binder transition from viscoelastic
solid to visco-elastic fluid. In this paper, two different
protocols were used to measure the viscosity property of binder using
a Brookfield Viscometer and there is a need to find the appropriate
mixing and compaction temperatures of various types of binders
which can result in complete aggregate coating and adequate field
density of HMA mixtures. The aim of this work is to find the
transition temperature from Non-Newtonian behavior to Newtonian
behavior of the binder by adopting a steady shear protocol and the
shear rate ramp protocol. The transition from non-Newtonian to
Newtonian can occur through an increase of temperature and shear of
the material. The test has been conducted for unmodified binder VG
30. The transition temperature was found in the unmodified binder
VG is 120oC. Therefore, the application of both modified binder and
unmodified binder in the pavement construction needs to be studied
properly by considering temperature and traffic loading factors of the
respective project site.
Abstract: The statistical study has become indispensable for various fields of knowledge. Not any different, in Geotechnics the study of probabilistic and statistical methods has gained power considering its use in characterizing the uncertainties inherent in soil properties. One of the situations where engineers are constantly faced is the definition of a probability distribution that represents significantly the sampled data. To be able to discard bad distributions, goodness-of-fit tests are necessary. In this paper, three non-parametric goodness-of-fit tests are applied to a data set computationally generated to test the goodness-of-fit of them to a series of known distributions. It is shown that the use of normal distribution does not always provide satisfactory results regarding physical and behavioral representation of the modeled parameters.
Abstract: The occurrences of precipitation, also commonly
referred as rain, in the form of "convective" and "stratiform" have
been identified to exist worldwide. In this study, the radar return
echoes or known as reflectivity values acquired from radar scans
have been exploited in the process of classifying the type of rain
endured. The investigation use radar data from Malaysian
Meteorology Department (MMD). It is possible to discriminate the
types of rain experienced in tropical region by observing the vertical
characteristics of the rain structure. .Heavy rain in tropical region
profoundly affects radiowave signals, causing transmission
interference and signal fading. Required wireless system fade margin
depends on the type of rain. Information relating to the two
mentioned types of rain is critical for the system engineers and
researchers in their endeavour to improve the reliability of
communication links. This paper highlights the quantification of
percentage occurrences over one year period in 2009.
Abstract: Environmental concerns about the scarcity of marine
resources are critical driving forces for firms aiming to prepare their
supply chains for sustainability. Building on previous work, this
paper highlights the implementation of good practices geared towards
sustainable operations in the seafood department, which were
pursued in an exploratory retailer case. Outcomes of the adopted
environmentally and socially acceptable fish retailing strategies,
ranged from traceability, to self-certification and eco-labelling. The
consequences for business were, as follows: stronger collaboration
and trust across the chain of custody, improvement of sponsors’
image and of consumers’ loyalty and, progress in the Greenpeace
retailers’ evaluation ranking.
Abstract: Genetic algorithm is widely used in optimization
problems for its excellent global search capabilities and highly parallel
processing capabilities; but, it converges prematurely and has a poor
local optimization capability in actual operation. Simulated annealing
algorithm can avoid the search process falling into local optimum. A
hybrid genetic algorithm based on simulated annealing is designed by
combining the advantages of genetic algorithm and simulated
annealing algorithm. The numerical experiment represents the hybrid
genetic algorithm can be applied to solve the function optimization
problems efficiently.
Abstract: In this study, Brillouin Gain Spectrum (BGS) is
experimentally analyzed in the Brillouin Optical Time Domain
Reflectometry (BOTDR) and Brillouin Optical Time Domain
Analyzer (BOTDA). For this purpose, the signal level of the
microwave generator is varied and the effects of BGS are
investigated. In the setups, 20 km conventional single mode fiber is
used to both setups and laser wavelengths are selected around 1550
nm. To achieve best results, it can be used between 5 dBm to 15 dBm
signal level of microwave generator for BOTDA and BOTDR setups.
Abstract: Computer education is referred to as the knowledge
and ability to use computers and related technology efficiently, with a
range of skills covering levels from basic use to advance. Computer
continues to make an ever-increasing impact on all aspect of human
endeavours such as education. With numerous benefits of computer
education, what are the insights of students on computer education?
This study investigated the perception of senior secondary school
students on computer education in Federal Capital Territory (FCT),
Abuja, Nigeria. A sample of 7500 senior secondary schools students
was involved in the study, one hundred (100) private and fifty (50)
public schools within FCT. They were selected by using simple
random sampling technique. A questionnaire [PSSSCEQ] was
developed and validated through expert judgement and reliability coefficient
of 0.84 was obtained. It was used to gather relevant data on
computer education. Findings confirmed that the students in the FCT
had positive perception on computer education. Some factors were
identified that affect students’ perception on computer education. The
null hypotheses were tested using t-test and ANOVA statistical
analyses at 0.05 level of significance. Based on these findings, some
recommendations were made which include competent teachers
should be employed into all secondary schools. This will help
students to acquire relevant knowledge in computer education,
technological supports should be provided to all secondary schools;
this will help the users (students) to solve specific problems in
computer education and financial supports should be provided to
procure computer facilities that will enhance the teaching and the
learning of computer education.
Abstract: The social logic of 'Sequina' slum area in Alexandria details the integral measure of space syntax at the room-level of twenty-building samples. The essence of spatial structure integrates the central 'visitor' domain with the 'living' frontage of the 'children' zone against the segregated privacy of the opposite 'parent' depth. Meanwhile, the multifunctioning of shallow rooms optimizes the integral 'visitor' structure through graph and visibility dimensions in contrast to the 'inhabitant' structure of graph-tails out of sight. Common theme of the layout integrity increases in compensation to the decrease of room visibility. Despite the 'pheno-type' of collective integration, the individual layouts observe 'geno-type' structure of spatial diversity per room adjoins. In this regard, the layout integrity alternates the cross-correlation of the 'kitchen & living' rooms with the 'inhabitant & visitor' domains of 'motherhood' dynamic structure. Moreover, the added 'grandparent' restructures the integral measure to become the deepest space, but opens to the 'living' of 'household' integrity. Some isomorphic layouts change the integral structure just through the 'balcony' extension of access, visual or ignored 'ringiness' of space syntax. However, the most integrated or segregated layouts invert the 'geno-type' into a shallow 'inhabitant' centrality versus the remote 'visitor' structure. Overview of the multivariate social logic of spatial integrity could never clarify without the micro-data analysis.
Abstract: Lightweight and efficient structures have the aim to
enhance the efficiency of the components in various industries.
Toward this end, composites are one of the most widely used
materials because of durability, high strength and modulus, and low
weight. One type of the advanced composites is grid-stiffened
composite (GSC) structures, which have been extensively considered
in aerospace, automotive, and aircraft industries. They are one of the
top candidates for replacing some of the traditional components,
which are used here. Although there are a good number of published
surveys on the design aspects and fabrication of GSC structures, little
systematic work has been reported on their material modification to
improve their properties, to our knowledge. Matrix modification
using nanoparticles is an effective method to enhance the flexural
properties of the fibrous composites. In the present study, a silanecoupling
agent (3-glycidoxypropyltrimethoxysilane/3-GPTS) was
introduced onto the silica (SiO2) nanoparticle surface and its effects
on the three-point flexural response of isogrid E-glass/epoxy
composites were assessed. Based on the Fourier Transform Infrared
Spectrometer (FTIR) spectra, it was inferred that the 3-GPTS
coupling agent was successfully grafted onto the surface of SiO2
nanoparticles after modification. Flexural test revealed an
improvement of 16%, 14%, and 36% in stiffness, maximum load and
energy absorption of the isogrid specimen filled with 3 wt.% 3-
GPTS/SiO2 compared to the neat one. It would be worth mentioning
that in these structures, considerable energy absorption was observed
after the primary failure related to the load peak. In addition, 3-
GPTMS functionalization had a positive effect on the flexural
behavior of the multiscale isogrid composites. In conclusion, this
study suggests that the addition of modified silica nanoparticles is a
promising method to improve the flexural properties of the gridstiffened
fibrous composite structures.
Abstract: Mineral product, waste concrete (fine aggregates),
waste in the optical field, industry, and construction employ separators
to separate solids and classify them according to their size. Various
sorting machines are used in the industrial field such as those operating
under electrical properties, centrifugal force, wind power, vibration,
and magnetic force. Study on separators has been carried out to
contribute to the environmental industry. In this study, we perform
CFD analysis for understanding the basic mechanism of the separation
of waste concrete (fine aggregate) particles from air with a machine
built with a rotor with blades. In CFD, we first performed
two-dimensional particle tracking for various particle sizes for the
model with 1 degree, 1.5 degree, and 2 degree angle between each
blade to verify the boundary conditions and the method of rotating
domain method to be used in 3D. Then we developed 3D numerical
model with ANSYS CFX to calculate the air flow and track the
particles. We judged the capability of particle separation for given size
by counting the number of particles escaping from the domain toward
the exit among 10 particles issued at the inlet. We confirm that
particles experience stagnant behavior near the exit of the rotating
blades where the centrifugal force acting on the particles is in balance
with the air drag force. It was also found that the minimum particle
size that can be separated by the machine with the rotor is determined
by its capability to stay at the outlet of the rotor channels.
Abstract: Information technology has been gaining more and
more space whether in industry, commerce or even for personal use,
but the misuse of it brings harm to the environment and human health
as a result. Contribute to the sustainability of the planet is to
compensate the environment, all or part of what withdraws it. The
green computing also came to propose practical for use in IT in an
environmentally correct way in aid of strategic management and
communication. This work focuses on showing how a mobile
application can help businesses reduce costs and reduced
environmental impacts caused by its processes, through a case study
of a public company in Brazil.
Abstract: This paper sets out a behavioral macro-model of a
Merged PiN and Schottky (MPS) diode based on silicon carbide
(SiC). This model holds good for both static and dynamic electrothermal
simulations for industrial applications. Its parameters have
been worked out from datasheets curves by drawing on the
optimization method: Simulated Annealing (SA) for the SiC MPS
diodes made available in the industry. The model also adopts the
Analog Behavioral Model (ABM) of PSPICE in which it has been
implemented. The thermal behavior of the devices was also taken
into consideration by making use of Foster’ canonical network as
figured out from electro-thermal measurement provided by the
manufacturer of the device.
Abstract: Manufacturing process has been considered as one of
the most important activity in business process. It correlates with
productivity and quality of the product so industries could fulfill
customer’s demand. With the increasing demand from customer,
industries must improve their manufacturing ability such as shorten
lead-time and reduce wastes on their process. Lean manufacturing
has been considered as one of the tools to waste elimination in
manufacturing or service industry. Workforce development is one
practice in lean manufacturing that can reduce waste generated from
operator such as waste of unnecessary motion. Anthropometric
approach is proposed to determine the recommended measurement in
operator’s work area. The method will get some dimensions from
Indonesia people that related to piston workstation. The result from
this research can be obtained new design for the work area
considering ergonomic aspect.
Abstract: Background modeling and subtraction in video
analysis has been widely used as an effective method for moving
objects detection in many computer vision applications. Recently, a
large number of approaches have been developed to tackle different
types of challenges in this field. However, the dynamic background
and illumination variations are the most frequently occurred problems
in the practical situation. This paper presents a favorable two-layer
model based on codebook algorithm incorporated with local binary
pattern (LBP) texture measure, targeted for handling dynamic
background and illumination variation problems. More specifically,
the first layer is designed by block-based codebook combining with
LBP histogram and mean value of each RGB color channel. Because
of the invariance of the LBP features with respect to monotonic
gray-scale changes, this layer can produce block wise detection results
with considerable tolerance of illumination variations. The pixel-based
codebook is employed to reinforce the precision from the output of the
first layer which is to eliminate false positives further. As a result, the
proposed approach can greatly promote the accuracy under the
circumstances of dynamic background and illumination changes.
Experimental results on several popular background subtraction
datasets demonstrate very competitive performance compared to
previous models.