Abstract: In this study, ultrasonic assisted machining (UAM) technique is applied in side-surface milling experiment for glass-ceramic workpiece material. The tungsten carbide cutting-tool with diamond coating is used in conjunction with two kinds of cooling/lubrication mediums such as water-soluble (WS) cutting fluid and minimum quantity lubricant (MQL). Full factorial process parameter combinations on the milling experiments are planned to investigate the effect of process parameters on cutting performance. From the experimental results, it tries to search for the better process parameter combination which the edge-indentation and the surface roughness are acceptable. In the machining experiments, ultrasonic oscillator was used to excite a cutting-tool along the radial direction producing a very small amplitude of vibration frequency of 20KHz to assist the machining process. After processing, toolmaker microscope was used to detect the side-surface morphology, edge-indentation and cutting tool wear under different combination of cutting parameters, and analysis and discussion were also conducted for experimental results. The results show that the main leading parameters to edge-indentation of glass ceramic are cutting depth and feed rate. In order to reduce edge-indentation, it needs to use lower cutting depth and feed rate. Water-soluble cutting fluid provides a better cooling effect in the primary cutting area; it may effectively reduce the edge-indentation and improve the surface morphology of the glass ceramic. The use of ultrasonic assisted technique can effectively enhance the surface finish cleanness and reduce cutting tool wear and edge-indentation.
Abstract: Reflux condensation occurs in vertical channels and tubes when there is an upward core flow of vapour (or gas-vapour mixture) and a downward flow of the liquid film. The understanding of this condensation configuration is crucial in the design of reflux condensers, distillation columns, and in loss-of-coolant safety analyses in nuclear power plant steam generators. The unique feature of this flow is the upward flow of the vapour-gas mixture (or pure vapour) that retards the liquid flow via shear at the liquid-mixture interface. The present model solves the full, elliptic governing equations in both the film and the gas-vapour core flow. The computational mesh is non-orthogonal and adapts dynamically the phase interface, thus produces a sharp and accurate interface. Shear forces and heat and mass transfer at the interface are accounted for fundamentally. This modeling is a big step ahead of current capabilities by removing the limitations of previous reflux condensation models which inherently cannot account for the detailed local balances of shear, mass, and heat transfer at the interface. Discretisation has been done based on finite volume method and co-located variable storage scheme. An in-house computer code was developed to implement the numerical solution scheme. Detailed results are presented for laminar reflux condensation from steam-air mixtures flowing in vertical parallel plate channels. The results include velocity and gas mass fraction profiles, as well as axial variations of film thickness.
Abstract: This paper is focused on the CFD simulation of the radiaxial pump (i.e. mixed flow pump) with the aim to detect the reasons of Y-Q characteristic instability. The main reasons of pressure pulsations were detected by means of the analysis of velocity and pressure fields within the pump combined with the theoretical approach. Consequently, the modifications of spiral case and pump suction area were made based on the knowledge of flow conditions and the shape of dissipation function. The primary design of pump geometry was created as the base model serving for the comparison of individual modification influences. The basic experimental data are available for this geometry. This approach replaced the more complicated and with respect to convergence of all computational tasks more difficult calculation for the compressible liquid flow. The modification of primary pump consisted in inserting the three fins types. Subsequently, the evaluation of pressure pulsations, specific energy curves and visualization of velocity fields were chosen as the criterion for successful design.
Abstract: Steel tubular towers serving as support structures for large wind turbines are subjected to several hundred million stress cycles caused by the turbulent nature of the wind. This causes highcycle fatigue, which could govern the design of the tower. Maintaining the support structure after the wind turbines reach its typical 20-year design life has become a common practice; however, quantifying the changes in the reliability on the tower is not usual. In this paper the effect of fatigue damage in the wind turbine structure is studied whit the use of fracture mechanics, and a method to estimate the reliability over time of the structure is proposed. A representative wind turbine located in Oaxaca, Mexico is then studied. It is found that the system reliability is significantly affected by the accumulation of fatigue damage.
Abstract: The use of energy dissipation systems for seismic applications has increased worldwide, thus it is necessary to develop practical and modern criteria for their optimal design. Here, a direct displacement-based seismic design approach for frame buildings with hysteretic energy dissipation systems (HEDS) is applied. The building is constituted by two individual structural systems consisting of: 1) a main elastic structural frame designed for service loads; and 2) a secondary system, corresponding to the HEDS, that controls the effects of lateral loads. The procedure implies to control two design parameters: a) the stiffness ratio (α=Kframe/Ktotal system), and b) the strength ratio (γ=Vdamper/Vtotal system). The proposed damage-controlled approach contributes to the design of a more sustainable and resilient building because the structural damage is concentrated on the HEDS. The reduction of the design displacement spectrum is done by means of a damping factor (recently published) for elastic structural systems with HEDS, located in Mexico City. Two limit states are verified: serviceability and near collapse. Instead of the traditional trial-error approach, a procedure that allows the designer to establish the preliminary sizes of the structural elements of both systems is proposed. The design methodology is applied to an 8-story steel building with buckling restrained braces, located in soft soil of Mexico City. With the aim of choosing the optimal design parameters, a parametric study is developed considering different values of હ and . The simplified methodology is for preliminary sizing, design, and evaluation of the effectiveness of HEDS, and it constitutes a modern and practical tool that enables the structural designer to select the best design parameters.
Abstract: The article deals with the tool in Matlab GUI form
that is designed to analyse a mechatronic system sensitivity and
tolerance. In the analysed mechatronic system, a torque is transferred
from the drive to the load through a coupling containing flexible
elements. Different methods of control system design are used. The
classic form of the feedback control is proposed using Naslin method,
modulus optimum criterion and inverse dynamics method. The
cascade form of the control is proposed based on combination of
modulus optimum criterion and symmetric optimum criterion. The
sensitivity is analysed on the basis of absolute and relative sensitivity
of system function to the change of chosen parameter value of the
mechatronic system, as well as the control subsystem. The tolerance
is analysed in the form of determining the range of allowed relative
changes of selected system parameters in the field of system stability.
The tool allows to analyse an influence of torsion stiffness, torsion
damping, inertia moments of the motor and the load and controller(s)
parameters. The sensitivity and tolerance are monitored in terms of
the impact of parameter change on the response in the form of system
step response and system frequency-response logarithmic
characteristics. The Symbolic Math Toolbox for expression of the
final shape of analysed system functions was used. The sensitivity
and tolerance are graphically represented as 2D graph of sensitivity
or tolerance of the system function and 3D/2D static/interactive graph
of step/frequency response.
Abstract: Family has a crucial role in maintaining the
physical, social and mental health of the children. Most of the
mental and anxiety problems of children reflect the complex
interpersonal situations among family members, especially parents.
In other words, anxiety problems of the children are correlated
with deficit relationships of family members and improper
childrearing styles. The parental child rearing styles leads to
positive and negative consequences which affect the children’s
mental health. Therefore, the present research was aimed to
compare the parental childrearing styles and anxiety of children
with stuttering and normal population. It was also aimed to study
the relationship between parental child rearing styles and anxiety
of children. The research sample included 54 boys with stuttering
and 54 normal boys who were selected from the children (boys) of
Tehran, Iran in the age range of 5 to 8 years in 2013. In order to
collect data, Baum-rind Childrearing Styles Inventory and Spence
Parental Anxiety Inventory were used. Appropriate descriptive
statistical methods and multivariate variance analysis and t test for
independent groups were used to test the study hypotheses.
Statistical data analyses demonstrated that there was a significant
difference between stuttering boys and normal boys in anxiety (t =
7.601, p< 0.01); but there was no significant difference between
stuttering boys and normal boys in parental childrearing styles (F =
0.129). There was also not found significant relationship between
parental childrearing styles and children anxiety (F = 0.135, p<
0.05). It can be concluded that the influential factors of children’s
society are parents, school, teachers, peers and media. So, parental
childrearing styles are not the only influential factors on anxiety of
children, and other factors including genetic, environment and
child experiences are effective in anxiety as well. Details are
discussed.
Abstract: The distribution of a single global clock across a chip
has become the major design bottleneck for high performance VLSI
systems owing to the power dissipation, process variability and multicycle
cross-chip signaling. A Network-on-Chip (NoC) architecture
partitioned into several synchronous blocks has become a promising
approach for attaining fine-grain power management at the system
level. In a NoC architecture the communication between the blocks is
handled asynchronously. To interface these blocks on a chip
operating at different frequencies, an asynchronous FIFO interface is
inevitable. However, these asynchronous FIFOs are not required if
adjacent blocks belong to the same clock domain. In this paper, we
have designed and analyzed a 16-bit asynchronous micropipelined
FIFO of depth four, with the awareness of place and route on an
FPGA device. We have used a commercially available Spartan 3
device and designed a high speed implementation of the
asynchronous 4-phase micropipeline. The asynchronous FIFO
implemented on the FPGA device shows 76 Mb/s throughput and a
handshake cycle of 109 ns for write and 101.3 ns for read at the
simulation under the worst case operating conditions (voltage =
0.95V) on a working chip at the room temperature.
Abstract: This paper presents effects of the mean operating
pressure on the optimal operating frequency based on temperature
differences across stack ends in a thermoacoustic refrigerator. In
addition to the length of the resonance tube, components of the
thermoacoustic refrigerator have an influence on the operating
frequency due to their acoustic properties, i.e., absorptivity,
reflectivity and transmissivity. The interference of waves incurs and
distorts the original frequency generated by the driver so that the
optimal operating frequency differs from the designs. These acoustic
properties are not parameters in the designs and be very complicated
to infer their responses. A prototype thermoacoustic refrigerator is
constructed and used to investigate its optimal operating frequency
compared to the design at various operating pressures. Helium and air
are used as working fluids during the experiments. The results
indicate that the optimal operating frequency of the prototype
thermoacoustic refrigerator using helium is at 6 bar and 490Hz or
approximately 20% away from the design frequency. The optimal
operating frequency at other mean pressures differs from the design
in an unpredictable manner, however, the optimal operating
frequency and pressure can be identified by testing.
Abstract: This paper presents dynamic models of distributed
generators (DG) and investigates dynamic behavior of the DG units
in the micro grid system. The DG units include photovoltaic and fuel
cell sources. The voltage source inverter is adopted since the
electronic interface which can be equipped with its controller to keep
stability of the micro grid during small signal dynamics. This paper
also introduces power management strategies and implements the DG
load sharing concept to keep the micro grid operation in gridconnected
and islanding modes of operation. The results demonstrate
the operation and performance of the photovoltaic and fuel cell as
distributed generators in a micro grid. The entire control system in
the micro grid is developed by combining the benefits of the power
control and the voltage control strategies. Simulation results are all
reported, confirming the validity of the proposed control technique.
Abstract: The paper is focused on the identification of limiting
environmental factors of individual industrial floors on which newly
developed polymer protection and repair systems with the use of
secondary raw materials will be used. These mainly include floors
with extreme stresses and special requirements for materials used. In
relation to the environment of a particular industrial floor, it is
necessary to ensure, for example, chemical stability, resistance to
higher temperatures, resistance to higher mechanical stress, etc. for
developed materials, which is reflected in the demands for the
developed material systems. The paper describes individual
environments and, in relation to them, also requirements for
individual components of the developed materials and for the
developed materials as a whole.
Abstract: In emerging economies, recycling is an opportunity
for the cities to increase the lifespan of sanitary landfills, reduce the
costs of the solid waste management, decrease the environmental
problems of the waste treatment through reincorporate waste in the
productive cycle and protect and develop people’s livelihoods of
informal waste pickers. However, few studies have analysed the
possibilities and strategies to integrate formal and informal sectors in
the solid waste management for the benefit of both. This study seek
to make a strength, weakness, opportunity, and threat (SWOT)
analysis in three recycling associations of Bogotá with the aim to
understand and determine the situation of recycling from perspective
of informal sector in its transition to enter as authorized waste
providers. Data used in the analysis are derived from multiple
strategies such as literature review, the Bogota’s recycling database,
focus group meetings, governmental reports, national laws and
regulations and specific interviews with key stakeholders. Results of
this study show as the main stakeholders of formal and informal
sector of waste management can identify the internal and internal
conditions of recycling in Bogotá. Several strategies were designed
based on the SWOTs determined, could be useful for Bogotá to
advance and promote recycling as a key strategy for integrated
sustainable waste management in the city.
Abstract: An innovative flooring underlayment was produced
and tested. The composite system is made of common OSB boards
and a layer of eco-friendly non-cement gypsum based material
(GeoGypTM). It was found that the shear bond between the two
materials is sufficient to secure the composite interaction between the
two. The very high compressive strength and relatively high tensile
strength of the non-cement based component together with its high
modulus of elasticity provides enough strength and stiffness for the
composite product to cover wider spacing between the joists. The
initial findings of this study indicate that with joist spacing as wide as
800 mm, the flooring system provides enough strength without
compromising the serviceability requirements of the building codes.
Abstract: Scrubbing by a liquid spraying is one of the most
effective processes used for removal of fine particles and soluble
gas pollutants (such as SO2, HCl, HF) from the flue gas. There are
many configurations of scrubbers designed to provide contact
between the liquid and gas stream for effectively capturing
particles or soluble gas pollutants, such as spray plates, packed bed
towers, jet scrubbers, cyclones, vortex and venturi scrubbers. The
primary function of venturi scrubber is the capture of fine particles
as well as HCl, HF or SO2 removal with effect of the flue gas
temperature decrease before input to the absorption column. In this
paper, sulfur dioxide (SO2) from flue gas was captured using new
design replacing venturi scrubber (1st degree of wet scrubbing).
The flue gas was prepared by the combustion of the carbon
disulfide solution in toluene (1:1 vol.) in the flame in the reactor.
Such prepared flue gas with temperature around 150°C was
processed in designed laboratory O-element scrubber. Water was
used as absorbent liquid. The efficiency of SO2 removal, pressure
drop and temperature drop were measured on our experimental
device. The dependence of these variables on liquid-gas ratio was
observed. The average temperature drop was in the range from
150°C to 40°C. The pressure drop was increased with increasing of
a liquid-gas ratio, but no too much as for the common venturi
scrubber designs. The efficiency of SO2 removal was up to 70 %.
The pressure drop of our new designed wet scrubber is similar to
commonly used venturi scrubbers; nevertheless the influence of
amount of the liquid on pressure drop is not so significant.
Abstract: This paper is concerned with knowledge representation
and extraction of fuzzy if-then rules using Interval Type-2
Context-based Fuzzy C-Means clustering (IT2-CFCM) with the aid of
fuzzy granulation. This proposed clustering algorithm is based on
information granulation in the form of IT2 based Fuzzy C-Means
(IT2-FCM) clustering and estimates the cluster centers by preserving
the homogeneity between the clustered patterns from the IT2 contexts
produced in the output space. Furthermore, we can obtain the
automatic knowledge representation in the design of Radial Basis
Function Networks (RBFN), Linguistic Model (LM), and Adaptive
Neuro-Fuzzy Networks (ANFN) from the numerical input-output data
pairs. We shall focus on a design of ANFN in this paper. The
experimental results on an estimation problem of energy performance
reveal that the proposed method showed a good knowledge
representation and performance in comparison with the previous
works.
Abstract: Moving into a new era of healthcare, new tools and
devices are developed to extend and improve health services, such as
remote patient monitoring and risk prevention. In this concept,
Internet of Things (IoT) and Cloud Computing present great
advantages by providing remote and efficient services, as well as
cooperation between patients, clinicians, researchers and other health
professionals. This paper focuses on patients suffering from bipolar
disorder, a brain disorder that belongs to a group of conditions
called affective disorders, which is characterized by great mood
swings. We exploit the advantages of Semantic Web and Cloud
Technologies to develop a patient monitoring system to support
clinicians. Based on intelligently filtering of evidence-knowledge and
individual-specific information we aim to provide treatment
notifications and recommended function tests at appropriate times or
concluding into alerts for serious mood changes and patient’s nonresponse
to treatment. We propose an architecture as the back-end
part of a cloud platform for IoT, intertwining intelligence devices
with patients’ daily routine and clinicians’ support.
Abstract: We investigate relaxation dynamics of a quantum
dipole emitter (QDE), e.g., a molecule or quantum dot, located near a
metal nanoparticle (MNP) exhibiting a dipolar localized surface
plasmon (LSP) resonance at the frequency of the QDE radiative
transition. It is shown that under the condition of the QDE-MNP
characteristic relaxation time being much shorter than that of the
QDE in free-space but much longer than the LSP lifetime. It is also
shown that energy dissipation in the QDE-MNP system is relatively
weak with the probability of the photon emission being about 0.75, a
number which, rather surprisingly, does not explicitly depend on the
metal absorption characteristics. The degree of entanglement
measured by the concurrency takes the maximum value, while the
distances between the QDEs and metal ball approximately are equal.
Abstract: Early diagnosis of infection like Hep-B virus in blood
is important for low cost medical treatment. For this purpose, it is
desirable to develop a point of care device which should be able to
detect trace quantities of the target molecule in blood. In this paper,
we report a nanoporous silicon oxide sensor which is capable of
detecting down to 1fM concentration of Hep-B surface antigen in
blood without the requirement of any centrifuge or pre-concentration.
This has been made possible by the presence of resonant peak in the
sensitivity characteristics. This peak is observed to be dependent only
on the concentration of the specific antigen and not on the interfering
species in blood serum. The occurrence of opposite impedance
change within the pores and at the bottom of the pore is responsible
for this effect. An electronic interface has also been designed to
provide a display of the virus concentration.
Abstract: Testability modeling is a commonly used method in
testability design and analysis of system. A dependency matrix will be
obtained from testability modeling, and we will give a quantitative
evaluation about fault detection and isolation.
Based on the dependency matrix, we can obtain the diagnosis tree.
The tree provides the procedures of the fault detection and isolation.
But the dependency matrix usually includes built-in test (BIT) and
manual test in fact. BIT runs the test automatically and is not limited
by the procedures. The method above cannot give a more efficient
diagnosis and use the advantages of the BIT.
A Comprehensive method of fault detection and isolation is
proposed. This method combines the advantages of the BIT and
Manual test by splitting the matrix. The result of the case study shows
that the method is effective.
Abstract: This paper presents the design and fabrication of an
optical window for an optical modulator toward image sensing
applications. An optical window consists of micrometer-order SiO2
capillaries (porous solid) that can modulate transmission light
intensity by moving the liquid in and out of porous solid. A high
optical transmittance of the optical window can be achieved due to
refractive index matching when the liquid is penetrated into the
porous solid. Otherwise, its light transmittance is lower because of
light reflection and scattering by air holes and capillary walls. Silicon
capillaries fabricated by deep reactive ion etching (DRIE) process are
completely oxidized to form the SiO2 capillaries. Therefore, high
aspect ratio SiO2 capillaries can be achieved based on silicon
capillaries formed by DRIE technique. Large compressive stress of
the oxide causes bending of the capillary structure, which is reduced
by optimizing the design of device structure. The large stress of the
optical window can be released via thin supporting beams. A 7.2 mm
x 9.6 mm optical window area toward a fully integrated with the
image sensor format is successfully fabricated and its optical
transmittance is evaluated with and without inserting liquids (ethanol
and matching oil). The achieved modulation range is approximately
20% to 35% with and without liquid penetration in visible region
(wavelength range from 450 nm to 650 nm).