Abstract: Ambient hydrolysis products in moist air and
hydrolysis kinetics in argon with humidity of RH1.5% for
polycrystalline LiH powders and sintered bulks were investigated by
X-ray diffraction, Raman spectroscopy and gravimetry. The results
showed that the hydrolysis products made up a layered structure of
LiOH•H2O/LiOH/Li2O from surface of the sample to inside. In low
humid argon atmosphere, the primary hydrolysis product was Li2O
rather than LiOH. The hydrolysis kinetic curves of LiH bulks present a
paralinear shape, which could be explained by the “Layer Diffusion
Control" model. While a three-stage hydrolysis kinetic profile was
observed for LiH powders under the same experimental conditions.
The first two sections were similar to that of the bulk samples, and the
third section also presents a linear reaction kinetics but with a smaller
reaction rate compared to the second section because of a larger
exothermic effect for the hydrolysis reaction of LiH powder.
Abstract: Gluconic acid is one of interesting chemical products
in industries such as detergents, leather, photographic, textile, and
especially in food and pharmaceutical industries. Fermentation is an
advantageous process to produce gluconic acid. Mathematical
modeling is important in the design and operation of fermentation
process. In fact, kinetic data must be available for modeling. The
kinetic parameters of gluconic acid production by Aspergillus niger
in batch culture was studied in this research at initial substrate
concentration of 150, 200 and 250 g/l. The kinetic models used were
logistic equation for growth, Luedeking-Piret equation for gluconic
acid formation, and Luedeking-Piret-like equation for glucose
consumption. The Kinetic parameters in the model were obtained by
minimizing non linear least squares curve fitting.
Abstract: Investigation of sandy clay behavior is important since
urban development demands mean that sandy clay areas are
increasingly encountered, especially for transportation
infrastructures. This paper presents the results of the finite element
analysis of the direct shear test (under three vertical loading 44, 96
and 192 kPa) and discusses the effects of different parameters such as
cohesion, friction angle and Young's modulus on the shear strength of
sandy clay. The numerical model was calibrated against the
experimental results of large-scale direct shear tests. The results have
shown that the shear strength was increased with increase in friction
angle and cohesion. However, the shear strength was not influenced
by raising the friction angle at normal stress of 44 kPa. Also, the
effect of different young's modulus factors on stress-strain curve was
investigated.
Abstract: Equations on curved manifolds display interesting properties in a number of ways. In particular, the symmetries and, therefore, the conservation laws reduce depending on how curved the manifold is. Of particular interest are the wave and Gordon-type equations; we study the symmetry properties and conservation laws of these equations on the Milne and Bianchi type III metrics. Properties of reduction procedures via symmetries, variational structures and conservation laws are more involved than on the well known flat (Minkowski) manifold.
Abstract: In this paper the authors propose a protocol, which uses Elliptic Curve Cryptography (ECC) based on the ElGamal-s algorithm, for sending small amounts of data via an authentication server. The innovation of this approach is that there is no need for a symmetric algorithm or a safe communication channel such as SSL. The reason that ECC has been chosen instead of RSA is that it provides a methodology for obtaining high-speed implementations of authentication protocols and encrypted mail techniques while using fewer bits for the keys. This means that ECC systems require smaller chip size and less power consumption. The proposed protocol has been implemented in Java to analyse its features and vulnerabilities in the real world.
Abstract: Effect of geometry on crushing behavior, energy absorption and failure mode of woven roving jute fiber/epoxy laminated composite tubes were experimentally studied. Investigations were carried out on three different geometrical types of composite tubes (circular, square and radial corrugated) subjected to axial compressive loading. It was observed in axial crushing study that the load bearing capability is significantly influenced by corrugation geometry. The influence of geometries of specimens was supported by the plotted load – displacement curves of the tests.
Abstract: Let F(x, y) = ax2 + bxy + cy2 be a positive definite
binary quadratic form with discriminant Δ whose base points lie on
the line x = -1/m for an integer m ≥ 2, let p be a prime number
and let Fp be a finite field. Let EF : y2 = ax3 + bx2 + cx be an
elliptic curve over Fp and let CF : ax3 + bx2 + cx ≡ 0(mod p) be
the cubic congruence corresponding to F. In this work we consider
some properties of positive definite quadratic forms, elliptic curves
and cubic congruences.
Abstract: Hydrate phase equilibria for the binary CO2+water and
CH4+water mixtures in silica gel pore of nominal diameters 6, 30, and
100 nm were measured and compared with the calculated results based
on van der Waals and Platteeuw model. At a specific temperature,
three-phase hydrate-water-vapor (HLV) equilibrium curves for pore
hydrates were shifted to the higher-pressure condition depending on
pore sizes when compared with those of bulk hydrates. Notably,
hydrate phase equilibria for the case of 100 nominal nm pore size were
nearly identical with those of bulk hydrates. The activities of water in
porous silica gels were modified to account for capillary effect, and
the calculation results were generally in good agreement with the
experimental data. The structural characteristics of gas hydrates in
silica gel pores were investigated through NMR spectroscopy.
Abstract: Super-quadrics can represent a set of implicit surfaces,
which can be used furthermore as primitive surfaces to construct a
complex object via Boolean set operations in implicit surface
modeling. In fact, super-quadrics were developed to create a
parametric surface by performing spherical product on two parametric
curves and some of the resulting parametric surfaces were also
represented as implicit surfaces. However, because not every
parametric curve can be redefined implicitly, this causes only implicit
super-elliptic and super-hyperbolic curves are applied to perform
spherical product and so only implicit super-ellipsoids and
hyperboloids are developed in super-quadrics. To create implicit
surfaces with more diverse shapes than super-quadrics, this paper
proposes an implicit representation of spherical product, which
performs spherical product on two implicit curves like super-quadrics
do. By means of the implicit representation, many new implicit curves
such as polygonal, star-shaped and rose-shaped curves can be used to
develop new implicit surfaces with a greater variety of shapes than
super-quadrics, such as polyhedrons, hyper-ellipsoids, superhyperboloids
and hyper-toroids containing star-shaped and roseshaped
major and minor circles. Besides, the newly developed implicit
surfaces can also be used to define new primitive implicit surfaces for
constructing a more complex implicit surface in implicit surface
modeling.
Abstract: In this paper, the translation surfaces in 3-dimensional
Euclidean space generated by two space curves have been
investigated. It has been indicated that Scherk surface is not only
minimal translation surface.
Abstract: The implementation of Super-Ultra Low Emission
Vehicle standards requires more efficient exhaust gas purification. To
increase the efficiency of exhaust gas purification, an the adsorbent
capable of holding hydrocarbons up to 250-300 ОС should be
developed. The possibility to design such adsorbents by modification
of zeolites of mordenite type, ZSM-5 and NaY, using different
metals cations has been studied.
It has been shown that introducing Cr, Cs, Zn, Ni, Co, Li, Mn in
zeolites results in modification of the toluene TPD and toluene
sorption capacity.
5%LiZSM-5 zeolite exhibits the most attractive TPD curve, with
toluene desorption temperature ranging from 250 to 350ОС. The
sorption capacity of 5%Li-ZSM-5 is 0.4 mmol/g. NaY zeolite has the
highest sorption capacity, up to 2 mmol/g, and holds toluene up to
350ОС, but at 120ОС toluene desorption starts, which is not desirable,
since the adsorbent of cold start hydrocarbons should retain them
until 250-300ОС. Therefore 5%LiZSM-5 zeolite was found to be the
most promising to control the cold-start hydrocarbon emissions
among the samples studied.
Abstract: Nanocrystalline thin film of Na0.1V2O5.nH2O xerogel
obtained by sol gel synthesis was used as gas sensor. Gas sensing
properties of different gases such as hydrogen, petroleum and
humidity were investigated. Applying XRD and TEM the size of the
nanocrystals is found to be 7.5 nm. SEM shows a highly porous
structure with submicron meter-sized voids present throughout the
sample. FTIR measurement shows different chemical groups
identifying the obtained series of gels. The sample was n-type
semiconductor according to the thermoelectric power and electrical
conductivity. It can be seen that the sensor response curves from
130oC to 150oC show a rapid increase in sensitivity for all types of
gas injection, low response values for heating period and the rapid
high response values for cooling period. This result may suggest that
this material is able to act as gas sensor during the heating and
cooling process.
Abstract: Scarcity of water resources and huge costs of
establishing new hydraulic installations necessitate optimal
exploitation from existing reservoirs. Sustainable management and
efficient exploitation from existing finite water resources are
important factors in water resource management, particularly in the
periods of water insufficiency and in dry regions, and on account of
competitive allocations in the view of exploitation management. This
study aims to minimize reservoir water release from a determined
rate of demand. A numerical model for water optimal exploitation
has been developed using GAMS introduced by the World Bank and
applied to the case of Meijaran dam, northern Iran. The results
indicate that this model can optimize the function of reservoir
exploitation while required water for lower parts of the region will be
supplied. Further, allocating optimal water from reservoir, the
optimal rate of water allocated to any group of the users were
specified to increase benefits in curve dam exploitation.
Abstract: The present study aims to evaluating the effect of
rotor solidity - in terms of chord length for a given rotor diameter - on
the performances of a small vertical axis Darrieus wind turbine. The
proposed work focuses on both power production and rotor power
coefficient, considering also the structural constraints deriving from
the centrifugal forces due to rotor angular velocity. Also the
smoothness of the resulting power curves have been investigated, in
order to evaluate the controllability of the corresponding rotor
architectures.
Abstract: Stress-strain curve of inter-tube connected carbon nanotube (CNT) reinforced polymer composite under axial loading generated from molecular dynamics simulation is presented. Comparison of the response to axial mechanical loading between this composite system with composite systems reinforced by long, continuous CNTs (replicated via periodic boundary conditions) and short, discontinuous CNTs has been made. Simulation results showed that the inter-tube connection improved the mechanical properties of short discontinuous CNTs dramatically. Though still weaker than long CNT/polymer composite, more remarkable increase in the stiffness relative to the polymer was observed in the inter-tube connected CNT/polymer composite than in the discontinuous CNT/polymer composite. The manually introduced bridge break process resulted in a stress-strain curve of ductile fracture mode, which is consistent with the experimental result.
Abstract: In this work, simulation algorithms for contact drying
of agitated particulate materials under vacuum and at atmospheric
pressure were developed. The implementation of algorithms gives a
predictive estimation of drying rate curves and bulk bed temperature
during contact drying. The calculations are based on the penetration
model to describe the drying process, where all process parameters
such as heat and mass transfer coefficients, effective bed properties,
gas and liquid phase properties are estimated with proper
correlations. Simulation results were compared with experimental
data from the literature. In both cases, simulation results were in good
agreement with experimental data. Few deviations were identified
and the limitations of the predictive capabilities of the models are
discussed. The programs give a good insight of the drying behaviour
of the analysed powders.
Abstract: The compression-absorption heat pump (C-A HP), one
of the promising heat recovery equipments that make process hot
water using low temperature heat of wastewater, was evaluated by
computer simulation. A simulation program was developed based on
the continuity and the first and second laws of thermodynamics. Both
the absorber and desorber were modeled using UA-LMTD method. In
order to prevent an unfeasible temperature profile and to reduce
calculation errors from the curved temperature profile of a mixture,
heat loads were divided into lots of segments. A single-stage
compressor was considered. A compressor cooling load was also
taken into account. An isentropic efficiency was computed from the
map data. Simulation conditions were given based on the system
consisting of ordinarily designed components. The simulation results
show that most of the total entropy generation occurs during the
compression and cooling process, thus suggesting the possibility that
system performance can be enhanced if a rectifier is introduced.
Abstract: Blind signatures enable users to obtain valid signatures for a message without revealing its content to the signer. This paper presents a new blind signature scheme, i.e. identity-based blind signature scheme with message recovery. Due to the message recovery property, the new scheme requires less bandwidth than the identitybased blind signatures with similar constructions. The scheme is based on modified Weil/Tate pairings over elliptic curves, and thus requires smaller key sizes for the same level of security compared to previous approaches not utilizing bilinear pairings. Security and efficiency analysis for the scheme is provided in this paper.
Abstract: Not all types of mobile phone are successful in entering the market because some types of the mobile phone have a negative perception of user. Therefore, it is important to understand the influence of mobile phone's characteristics in the local user perception. This research investigates the influence of QWERTY mobile phone's forms in the perception of Indonesian user. First, some alternatives of mobile phone-s form are developed based on a certain number of mobile phone's models. At the second stage, some word pairs as design attributes of the mobile phone are chosen to represent the user perception of mobile phone. At the final stage, a survey is conducted to investigate the influence of the developed form alternatives to the user perception. Based on the research, users perceive mobile phone's form with curved top and straight bottom shapes and mobile phone's form with slider and antenna as the most negative form. Meanwhile, mobile phone's form with curved top and bottom shapes and mobile phone-s form without slider and antenna are perceived by the user as the most positive form.
Abstract: This study is concerned with the investigation of the
suitability of several empirical and semi-empirical drying models
available in the literature to define drying behavior of viscose yarn
bobbins. For this purpose, firstly, experimental drying behaviour of
viscose bobbins was determined on an experimental dryer setup
which was designed and manufactured based on hot-air bobbin
dryers used in textile industry. Afterwards, drying models considered
were fitted to the experimentally obtained moisture ratios. Drying
parameters were drying temperature and bobbin diameter. The fit
was performed by selecting the values for constants in the models in
such a way that these values make the sum of the squared differences
between the experimental and the model results for moisture ratio
minimum. Suitability of fitting was specified as comparing the
correlation coefficient, standard error and mean square deviation.
The results show that the most appropriate model in describing the
drying curves of viscose bobbins is the Page model.