Abstract: Revolutions Applications such as telecommunications, hands-free communications, recording, etc. which need at least one microphone, the signal is usually infected by noise and echo. The important application is the speech enhancement, which is done to remove suppressed noises and echoes taken by a microphone, beside preferred speech. Accordingly, the microphone signal has to be cleaned using digital signal processing DSP tools before it is played out, transmitted, or stored. Engineers have so far tried different approaches to improving the speech by get back the desired speech signal from the noisy observations. Especially Mobile communication, so in this paper will do reconstruction of the speech signal, observed in additive background noise, using the Kalman filter technique to estimate the parameters of the Autoregressive Process (AR) in the state space model and the output speech signal obtained by the MATLAB. The accurate estimation by Kalman filter on speech would enhance and reduce the noise then compare and discuss the results between actual values and estimated values which produce the reconstructed signals.
Abstract: This paper was to study the clothes dryer using waste
heat from a split type air conditioner with a capacity of 12,648 btu/h.
The drying chamber had a minimum cross section area with the size
of 0.5 x 1.0 m2. The chamber was constructed by sailcloth and was
inside folded with aluminium foil. Then, it was connected to the
condensing unit of an air conditioner. The experiment was carried out
in two aspects which were the clothes drying with and without
auxiliary fan unit. The results showed that the drying rate of clothes
in the chamber installed with and without auxiliary fan unit were
2.26 and 1.1 kg/h, respectively. In case of the chamber installed with
a auxiliary fan unit, the additional power of 0.011 kWh was
consumed and the drying rate was higher than that of clothes drying
without auxiliary fan unit. Without auxiliary fan unit installation, no
energy was required but there was a portion of hot air leaks away
through the punctured holes at the wall of the drying chamber, hence
the drying rate was dropped below. The drying rate of clothes drying
using waste heat was higher than natural indoor drying and
commercial dryer which their drying rate were 0.17 and 1.9 kg/h,
respectively. It was noted that the COP of the air conditioner did not
change during the operating of clothes drying.
Abstract: In this paper, we present a vertical wire NMOS
device fabricated using CMOS compatible processes. The
impact of temperature on various device parameters is
investigated in view of usual increase in surrounding
temperature with device density.
Abstract: Simultaneous Saccharification and Fermentation (SSF) of sugarcane bagasse by cellulase and Pachysolen tannophilus MTCC *1077 were investigated in the present study. Important process variables for ethanol production form pretreated bagasse were optimized using Response Surface Methodology (RSM) based on central composite design (CCD) experiments. A 23 five level CCD experiments with central and axial points was used to develop a statistical model for the optimization of process variables such as incubation temperature (25–45°) X1, pH (5.0–7.0) X2 and fermentation time (24–120 h) X3. Data obtained from RSM on ethanol production were subjected to the analysis of variance (ANOVA) and analyzed using a second order polynomial equation and contour plots were used to study the interactions among three relevant variables of the fermentation process. The fermentation experiments were carried out using an online monitored modular fermenter 2L capacity. The processing parameters setup for reaching a maximum response for ethanol production was obtained when applying the optimum values for temperature (32°C), pH (5.6) and fermentation time (110 h). Maximum ethanol concentration (3.36 g/l) was obtained from 50 g/l pretreated sugarcane bagasse at the optimized process conditions in aerobic batch fermentation. Kinetic models such as Monod, Modified Logistic model, Modified Logistic incorporated Leudeking – Piret model and Modified Logistic incorporated Modified Leudeking – Piret model have been evaluated and the constants were predicted.
Abstract: Method of determining of moisture diffusivity on two types of autoclaved aerated concretes with different bulk density is represented in the paper. On the specimens were measured one dimensional water transport only on liquid phase. Ever evaluation was done from moisture profiles measured in specific times by capacitance moisture meter. All values from capacitance meter were recalculated to moisture content by mass. Moisture diffusivity was determined in dependence on both moisture and temperature. The experiment temperatures were set at values 55, 65, 75 and 85°C.
Abstract: It can be said that the business sector is faced with a range of challenges–a rapidly changing business environment, an increase and diversification of customers- demands and the consequent need for quick response–for having in place flexible management and production info systems. As a matter of fact, many manufacturers have adopted production info management systems such as MES and ERP. Nevertheless, managers are having difficulties obtaining ever-changing production process information in real time, or responding quickly to any change in production related needs on the basis of such information. This is because they rely on poor production info systems which are not capable of providing real-time factory settings. If the manufacturer doesn-t have a capacity for collecting or digitalizing the 4 Ms (Man, Machine, Material, Method), which are resources for production, on a real time basis, it might to difficult to effectively maintain the information on production process. In this regard, this paper will introduce some new alternatives to the existing methods of collecting the 4 Ms in real time, which are currently comprise the production field.
Abstract: A mobile ad hoc network is a network of mobile nodes
without any notion of centralized administration. In such a network,
each mobile node behaves not only as a host which runs applications
but also as a router to forward packets on behalf of others. Clustering
has been applied to routing protocols to achieve efficient
communications. A CH network expresses the connected relationship
among cluster-heads. This paper discusses the methods for
constructing a CH network, and produces the following results: (1)
The required running costs of 3 traditional methods for constructing a
CH network are not so different from each other in the static
circumstance, or in the dynamic circumstance. Their running costs in
the static circumstance do not differ from their costs in the dynamic
circumstance. Meanwhile, although the routing costs required for the
above 3 methods are not so different in the static circumstance, the
costs are considerably different from each other in the dynamic
circumstance. Their routing costs in the static circumstance are also
very different from their costs in the dynamic circumstance, and the
former is one tenths of the latter. The routing cost in the dynamic
circumstance is mostly the cost for re-routing. (2) On the strength of
the above results, we discuss new 2 methods regarding whether they
are tolerable or not in the dynamic circumstance, that is, whether the
times of re-routing are small or not. These new methods are revised
methods that are based on the traditional methods. We recommended
the method which produces the smallest routing cost in the dynamic
circumstance, therefore producing the smallest total cost.
Abstract: A compact 1x3 power splitter based on Photonic
Crystal Waveguides (PCW) with flexible power splitting ratio is
presented in this paper. Multimode interference coupler (MMI) is
integrated with PCW. The device size reduction compared with the
conventional MMI power splitter is attributed to the large dispersion
of the PCW. Band Solve tool is used to calculate the band structure of
PCW. Finite Difference Time Domain (FDTD) method is adopted to
simulate the relevant structure at 1550nm wavelength. The device is
polarization insensitive and allows the control of output (o/p) powers
within certain percentage points for both polarizations.
Abstract: The application of agro-industrial waste in Aluminum
Metal Matrix Composites has been getting more attention as they
can reinforce particles in metal matrix which enhance the strength
properties of the composites. In addition, by applying these agroindustrial
wastes in useful way not only save the manufacturing cost
of products but also reduce the pollutions on environment. This
paper represents a literature review on a range of industrial wastes
and their utilization in metal matrix composites. The paper describes
the synthesis methods of agro-industrial waste filled metal matrix
composite materials and their mechanical, wear, corrosion, and
physical properties. It also highlights the current application and
future potential of agro-industrial waste reinforced composites in
aerospace, automotive and other construction industries.
Abstract: This paper proposes two types of non-isolated
direct AC-DC converters. First, it shows a buck-boost
converter with an H-bridge, which requires few components
(three switches, two diodes, one inductor and one capacitor) to
convert AC input to DC output directly. This circuit can handle
a wide range of output voltage. Second, a direct AC-DC buck
converter is proposed for lower output voltage applications.
This circuit is analyzed with output voltage of 12V. We
describe circuit topologies, operation principles and simulation
results for both circuits.
Abstract: This paper highlights the importance of the selection
of the building-s wall material,and the shortcomings of the most
commonly used framed structures with masonry infills .The
objective of this study is investigating the behavior of infill walls as
structural components in existing structures.Structural infill walls are
very important in structural behavior under earthquake effects.
Structural capacity under the effect of earthquake,displacement and
relative story displacement are affected by the structural irregularities
.The presence of nonstructural masonry infill walls can modify
extensively the global seismic behavior of framed buildings .The
stability and integrity of reinforced concrete frames are enhanced by
masonry infill walls. Masonry infill walls alter displacement and
base shear of the frame as well. Short columns have great
importance during earthquakes,because their failure may lead to
additional structural failures and result in total building collapse.
Consequently the effects of short columns are considered in this
study.
Abstract: This case study investigates the effects of reactive
focus on form through negotiation on the linguistic development of
an adult EFL learner in an exclusive private EFL classroom. The
findings revealed that in this classroom negotiated feedback occurred
significantly more often than non-negotiated feedback. However, it
was also found that in the long run the learner was significantly more
successful in correcting his own errors when he had received nonnegotiated
feedback than negotiated feedback. This study, therefore,
argues that although negotiated feedback seems to be effective for
some learners in the short run, it is non-negotiated feedback which
seems to be more effective in the long run. This long lasting effect
might be attributed to the impact of schooling system which is itself
indicative of the dominant culture, or to the absence of other
interlocutors in the course of interaction.
Abstract: In this paper, we evaluate the performance of the
Hybrid-MIMO Receiver Scheme (HMRS) in Cognitive Radio
network (CR-network). We investigate the efficiency of the proposed
scheme which the energy level and user number of primary user are
varied according to the characteristic of CR-network. HMRS can
allow users to transmit either Space-Time Block Code (STBC) or
Spatial-Multiplexing (SM) streams simultaneously by using
Successive Interference Cancellation (SIC) and Maximum Likelihood
Detection (MLD). From simulation, the results indicate that the
interference level effects to the performance of HMRS. Moreover,
the exact closed-form capacity of the proposed scheme is derived and
compared with STBC scheme.
Abstract: Factoring Boolean functions is one of the basic operations in algorithmic logic synthesis. A novel algebraic factorization heuristic for single-output combinatorial logic functions is presented in this paper and is developed based on the set theory paradigm. The impact of factoring is analyzed mainly from a low power design perspective for standard cell based digital designs in this paper. The physical implementation of a number of MCNC/IWLS combinational benchmark functions and sub-functions are compared before and after factoring, based on a simple technology mapping procedure utilizing only standard gate primitives (readily available as standard cells in a technology library) and not cells corresponding to optimized complex logic. The power results were obtained at the gate-level by means of an industry-standard power analysis tool from Synopsys, targeting a 130nm (0.13μm) UMC CMOS library, for the typical case. The wire-loads were inserted automatically and the simulations were performed with maximum input activity. The gate-level simulations demonstrate the advantage of the proposed factoring technique in comparison with other existing methods from a low power perspective, for arbitrary examples. Though the benchmarks experimentation reports mixed results, the mean savings in total power and dynamic power for the factored solution over a non-factored solution were 6.11% and 5.85% respectively. In terms of leakage power, the average savings for the factored forms was significant to the tune of 23.48%. The factored solution is expected to better its non-factored counterpart in terms of the power-delay product as it is well-known that factoring, in general, yields a delay-efficient multi-level solution.
Abstract: This paper focuses on the development of bond graph
dynamic model of the mechanical dynamics of an excavating mechanism
previously designed to be used with small tractors, which are
fabricated in the Engineering Workshops of Jomo Kenyatta University
of Agriculture and Technology. To develop a mechanical dynamics
model of the manipulator, forward recursive equations similar to
those applied in iterative Newton-Euler method were used to obtain
kinematic relationships between the time rates of joint variables
and the generalized cartesian velocities for the centroids of the
links. Representing the obtained kinematic relationships in bondgraphic
form, while considering the link weights and momenta as
the elements led to a detailed bond graph model of the manipulator.
The bond graph method was found to reduce significantly the number
of recursive computations performed on a 3 DOF manipulator for a
mechanical dynamic model to result, hence indicating that bond graph
method is more computationally efficient than the Newton-Euler
method in developing dynamic models of 3 DOF planar manipulators.
The model was verified by comparing the joint torque expressions
of a two link planar manipulator to those obtained using Newton-
Euler and Lagrangian methods as analyzed in robotic textbooks. The
expressions were found to agree indicating that the model captures
the aspects of rigid body dynamics of the manipulator. Based on
the model developed, actuator sizing and valve sizing methodologies
were developed and used to obtain the optimal sizes of the pistons
and spool valve ports respectively. It was found that using the pump
with the sized flow rate capacity, the engine of the tractor is able to
power the excavating mechanism in digging a sandy-loom soil.
Abstract: The study of the fouling deposition of pink guava
juice (PGJ) is relatively new research compared to milk fouling
deposit. In this work, a new experimental set-up was developed to
imitate the fouling formation in heat exchanger, namely a continuous
flow experimental set-up heat exchanger. The new experimental setup
was operated under industrial pasteurization temperature of PGJ,
which was at 93°C. While the flow rate and pasteurization period
were based on the experimental capacity, which were 0.5 and 1
liter/min for the flow rate and the pasteurization period was set for 1
hour. Characterization of the fouling deposit was determined by
using various methods. Microstructure of the deposits was carried
out using ESEM. Proximate analyses were performed to determine
the composition of moisture, fat, protein, fiber, ash and carbohydrate
content. A study on the hardness and stickiness of the fouling deposit
was done using a texture analyzer. The presence of seedstone in pink
guava juice was also analyzed using a particle analyzer. The findings
shown that seedstone from pink guava juice ranging from 168 to
200μm and carbohydrate was found to be a major composition
(47.7% of fouling deposit consists of carbohydrate). Comparison
between the hardness and stickiness of the deposits at two different
flow rates showed that fouling deposits were harder and denser at
higher flow rate. Findings from this work provide basis knowledge
for further study on fouling and cleaning of PGJ.
Abstract: 98% of the energy needed in Taiwan has been
imported. The prices of petroleum and electricity have been
increasing. In addition, facility capacity, amount of electricity
generation, amount of electricity consumption and number of Taiwan
Power Company customers have continued to increase. For these
reasons energy conservation has become an important topic. In the
past linear regression was used to establish the power consumption
models for chillers. In this study, grey prediction is used to evaluate
the power consumption of a chiller so as to lower the total power
consumption at peak-load (so that the relevant power providers do not
need to keep on increasing their power generation capacity and facility
capacity).
In grey prediction, only several numerical values (at least four
numerical values) are needed to establish the power consumption
models for chillers. If PLR, the temperatures of supply chilled-water
and return chilled-water, and the temperatures of supply cooling-water
and return cooling-water are taken into consideration, quite accurate
results (with the accuracy close to 99% for short-term predictions)
may be obtained. Through such methods, we can predict whether the
power consumption at peak-load will exceed the contract power
capacity signed by the corresponding entity and Taiwan Power
Company. If the power consumption at peak-load exceeds the power
demand, the temperature of the supply chilled-water may be adjusted
so as to reduce the PLR and hence lower the power consumption.
Abstract: In this paper we present a linear autozeroing ultra lowvoltage amplifier. The autozeroing performed by all ULV circuits is important to reduce the impact of noise and especially avoid power supply noise in mixed signal low-voltage CMOS circuits. The simulated data presented is relevant for a 90nm TSMC CMOS process.
Abstract: The use and management of projects has risen to
a new prominence, with projects seen as critical to economic in
both the private and public sectors due challenging and dynamic
business environment. However, failure in managing project is
encountered regularly, which cause the waste of company
resources. The impacts of projects that failed to meet
stakeholders expectations have left behind long lasting negative
consequences in organization. Therefore, this research aims to
investigate on key success factors of project management in an
organization. It is believed that recognizing important factors
that contribute to successful project will help companies to
increase the overall profitability. 150 questionnaires were
distributed to respondents and 110 questionnaires were collected
and used in performing the data analysis. The result has strongly
supported the relationship between independent variables and
project performance.
Abstract: With the rapid usage of portable devices mobility in
IP networks becomes more important issue in the recent years. IETF
standardized Mobile IP that works in Network Layer, which involves
tunneling of IP packets from HA to Foreign Agent. Mobile IP suffers
many problems of Triangular Routing, conflict with private
addressing scheme, increase in load in HA, need of permanent home
IP address, tunneling itself, and so on. In this paper, we proposed
mobility management in Application Layer protocol SIP and show
some comparative analysis between Mobile IP and SIP in context of
mobility.