Abstract: Energy and exergy study of air-water combined solar collector which is called dual purpose solar collector (DPSC) is investigated. The method of ε - NTU is used. Analysis is performed for triangle channels. Parameters like the air flow rate and water inlet temperature are studied. Results are shown that DPSC has better energy and exergy efficiency than single collector. In addition, the triangle passage with water inlet temperature of 60O C has shown better exergy and energy efficiency.
Abstract: Fatigue behaviors of Lead Zirconate Titanate (PZT)
ceramics under different amplitude of bipolar electrical loads have
been investigated. Fatigue behavior is represented by the change of
hysteresis loops and remnant polarization. Three levels of electrical
load amplitudes (1.00, 1.25 and 1.50 kV /mm) were applied in this
experimental. It was found that the remnant polarization decreased
significantly with the number of loading cycles. The degree of fatigue
degradation depends on the amplitude of electric field. The higher
amplitude exhibits the greater fatigue degradation.
Abstract: This paper presents an alternative strategy of queuing
handover called Pseudo Last Useful Instant PLUI scheme for Low
Earth Orbit Mobile Satellite Systems LEO MSSs. The PLUI scheme
uses the same approach as the Last Useful Instant LUI scheme
previously proposed in literature, with less complex implementation.
Simulation tests were carried out using Dynamic Channel Allocation
DCA in order to evaluate the performance of this scheme and also an
analytical approach has been presented to allow the performance
evaluation of Fixed Channel Allocation FCA, with different
handover queuing disciplines. The results show that performances
achieved by the proposed strategy are close to those achieved using
the LUI scheme.
Abstract: In this paper we have proposed three and two
stage still gray scale image compressor based on BTC. In our
schemes, we have employed a combination of four techniques
to reduce the bit rate. They are quad tree segmentation, bit
plane omission, bit plane coding using 32 visual patterns and
interpolative bit plane coding. The experimental results show
that the proposed schemes achieve an average bit rate of 0.46
bits per pixel (bpp) for standard gray scale images with an
average PSNR value of 30.25, which is better than the results
from the exiting similar methods based on BTC.
Abstract: The purpose of this study was to investigate relationships between satisfaction with major and career decision efficacy and career attitude maturity of engineering college students by performing correlation analysis. Gender differences in between satisfaction with major and career decision efficacy and career attitude maturity were also examined by T-test. The results T-test revealed gender differences in only career decision efficacy. Male Students scored significantly higher than did female students on career decision efficacy and satisfaction with major. The results of correlation analysis showed a) satisfaction with major were significantly associated with career decision efficacy, b) satisfaction with major were significantly associated with career attitude maturity, and c) career decision efficacy were significantly associated with career attitude maturity. As a result,we found the importance of satisfaction in engineering college students- major studies when deciding their career.
Abstract: This article presents a current-mode universal biquadratic filter. The proposed circuit can apparently provide standard functions of the biquad filter: low-pass, high-pass, bandpass, band-reject and all-pass functions. The circuit uses 4 current controlled transconductance amplifiers (CCTAs) and 2 grounded capacitors. In addition, the pole frequency and quality factor can be adjusted by electronic method by adjusting the bias currents of the CCTA. The proposed circuit uses only grounded capacitors without additional external resistors, the proposed circuit is considerably appropriate to further developing into an integrated circuit. The results of PSPICE simulation program are corresponding to the theoretical analysis.
Abstract: This article presents a performance comparison of an
interior mounted permanent magnet synchronous generator (IPMSG)
with a synchronous reluctance generator (SynRG) with the same size
for a wind application. It is found that using the same geometrical
dimensions, a SynRG can convert 74 % of the power that an IPMSG
can convert, while it has 80% of the IPMSG weight. Moreover it is
found that the efficieny for the IMPSG is 99% at rated power
compared to 98.7% for the SynRG.
Abstract: The study of non-equilibrium systems has attracted
increasing interest in recent years, mainly due to the lack of
theoretical frameworks, unlike their equilibrium counterparts.
Studying the steady state and/or simple systems is thus one of the
main interests. Hence in this work we have focused our attention on
the driven lattice gas model (DLG model) consisting of interacting
particles subject to an external field E. The dynamics of the system
are given by hopping of particles to nearby empty sites with rates
biased for jumps in the direction of E. Having used small two
dimensional systems of DLG model, the stochastic properties at nonequilibrium
steady state were analytically studied. To understand the
non-equilibrium phenomena, we have applied the analytic approach
via master equation to calculate probability function and analyze
violation of detailed balance in term of the fluctuation-dissipation
theorem. Monte Carlo simulations have been performed to validate
the analytic results.
Abstract: The purpose of this study is to research on thoughts transmitted from virtual fitting-room and to deduce discussion in an auxiliary narrative way. The research structure is based on 3D virtual fitting-room as the research subject. Initially, we will discuss the principles of narrate study, User Demand and so on by using a narrative design pattern to transmit their objective indications of “people-situation-reason-object", etc, and then to analyze the virtual fitting-room examples that are able to provide a new thinking for designers who engaged in clothing related industry – which comes in “story telling" and “user-centered design" forms. Clothing designs are not just to cover up the body to keep warm but to draw closer to people-s demand physiologically and psychologically through interactive designs so as to achieve cognition between people and environment. In the “outside" goal of clothing-s functional designs, we use tribal group-s behavior characteristics to “transform" the existing personal cultural stories, and “reform" them to design appropriate interactive products. Synthesizing the above matters, apart from being able to regard “narrate" as a kind of functional thinking process, we are also able to regard it as a kind of choice, arrangement and an activity of story expression, allowing interactive design-s spirit, product characteristics and experience ideas be transmitted to target tribal group in a visual image performance method. It is a far more confident and innovative attempt, and meanwhile, able to achieve entertainment, joyful and so forth fundamental interactive transmissions. Therefore, this study takes “user-centered design" thinking as a basis to establish a set of clothing designs with interactive experience patterns and to assist designers to examine the five sensual feeling of interactive demands in order to initiate a new value in textile industry.
Abstract: This study focuses on an evaluation of Hokkaido which
is the northernmost and largest prefecture by surface area in Japan and
particularly on two points: the rivalry between all kinds of land use
such as urban land and agricultural and forestry land in various cities
and their surrounding areas and the possibilities for forestry biomass in
areas other than those mentioned above and grasps which areas require
examination of the nature of land use control and guidance through
conducting land use analysis at the district level using GIS
(Geographic Information Systems). The results of analysis in this
study demonstrated that it is essential to divide the whole of Hokkaido
into two areas: those within delineated city planning areas and those
outside of delineated city planning areas and to conduct an evaluation
of each land use control.
In delineated urban areas, particularly urban areas, it is essential to
re-examine land use from the point of view of compact cities or smart
cities along with conducting an evaluation of land use control that
focuses on issues of rivalry between all kinds of land use such as urban
land and agricultural and forestry land. In areas outside of delineated
urban areas, it is desirable to aim to build a specific community
recycling range based on forest biomass utilization by conducting an
evaluation of land use control concerning the possibilities for forest
biomass focusing particularly on forests within and outside of city
planning areas.
Abstract: Power system stabilizers (PSS) are now routinely used in the industry to damp out power system oscillations. In this paper, particle swarm optimization (PSO) technique is applied to design a robust power system stabilizer (PSS). The design problem of the proposed controller is formulated as an optimization problem and PSO is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor speed of the generator is involved; stability performance of the system is improved. The non-linear simulation results are presented under wide range of operating conditions; disturbances at different locations as well as for various fault clearing sequences to show the effectiveness and robustness of the proposed controller and their ability to provide efficient damping of low frequency oscillations. Further, all the simulations results are compared with a conventionally designed power system stabilizer to show the superiority of the proposed design approach.
Abstract: Aim of this work was to compare the efficacy of two
loading methods of proteins onto polymeric nanocarriers: adsorption
and encapsulation methods. Preliminary studies of protein loading
were done using Bovine Serum Albumin (BSA) as model protein.
Nanocarriers were prepared starting from polylactic co-glycolic acid
(PLGA) polymer; production methods used are two different variants
of emulsion evaporation method. Nanoparticles obtained were
analyzed in terms of dimensions by Dynamic Light Scattering and
Loading Efficiency of BSA by Bradford Assay. Loaded
nanoparticles were then submitted to in-vitro protein dissolution test
in order to study the effect of the delivery system on the release rate
of the protein.
Abstract: Asthma is a condition that causing chronic health problems in children. In addition to basic therapy against disease, we must try to reduce the impact of chronic health problems and also optimize their medical aspect of growth and development. A boy with mild asthma attack frequent episode did not showed any improvement with medical treatment and his asthma control test was 11. From radiologic examination he got hyperaerated lung and billateral sinusitis maxillaris; skin test results were house dust, food and pet allergy; an overweight body; bad school grades; psychological and environmental problem. We followed and evaluated this boy in 6 months, treated holistically. Even we could not do much on environmental but no more psychological and school problems, his on a good bodyweight and his asthma control test was 22. A case of a child with mild asthma attack frequent episode was reported. Asthma clinical course show no significant improvement when other predisposing factor is not well-controlled and a child’s growth and development may be affected. Improving condition of the patient can be created with the help of loving and caring way of nurturing from the parents and supportive peer group. Therefore, continuous and consistent monitoring is required because prognosis of asthma is generally good when regularly and properly controlled.
Abstract: Twenty four New Zealand white rabbits (12 does and
12 bucks) and twenty four Flanders (12 does and 12 bucks) rabbits,
allotted into two feeding regime (6 for each breed, 3 males and 3
females) first one fed commercial ration and second one fed
commercial diet plus sodium butyrate (300 g/ton). The obtained
results showed that at end of 8th week experimental period New
Zealand white rabbits were heavier body weight than Flanders rabbits
(1934.55+39.05 vs. 1802.5+30.99 g); significantly high body weight
gain during experimental period especially during 8th week
(136.1+3.5 vs. 126.8+1.8 g/week); better feed conversion ratio during
all weeks of experiment from first week (3.07+0.16 vs. 3.12+0.10)
till the 8th week of experiment (5.54+0.16 vs. 5.76+0.07) with
significantly high dressing percentages (0.54+0.01 vs. 0.52+0.01).
Also all carcass cuts were significantly high in New Zealand white
rabbits than Flanders. Females rabbits (at the same age) were lower
body weight than males from start of experiment (941.1+39.8
vs.972.1+33.5 g) till the end of experiment (1833.64+37.69 vs.
1903.41+36.93 g); gained less during all weeks of experiment except
during 8th week (132.1+2.3 vs. 130.9+3.4 g/week), with lower
dressing percentage (0.52+0.01 vs. 0.53+0.01) and lighter carcass
cuts than males, however, they had better feed conversion ratio
during 1st week, 7th week and 8th week of experiment. Addition of
300g sodium butyrate/ton of rabbit increased the body weight of
rabbits at the end of experimental period (1882.71+26.45 vs.
1851.5+49.82 g); improve body weight gain at 3rd, 4th, 5th, 6th and
7th week of experiment and significantly improve feed conversion
ratio during all weeks of the experiment from 1st week (2.85+0.07
vs. 3.30+0.15) till the 8th week of the experiment (5.51+0.12 vs.
5.77+0.12). Also the dressing percentage was higher in Sodium
butyrate fed groups than control one (0.53+0.01 vs. 0.52+0.01) and
the most important results of feeding sodium butyrate is the reducing
of the mortality percentage in rabbits during 8 week experiment to
zero percentage as compared with 16% in control group.
Abstract: The main purpose of this paper is to investigate thelong-run equilibrium and short-run dynamics of international housing prices when macroeconomic variables change. We apply the Pedroni’s, panel cointegration, using the unbalanced panel data analysis of 33 countries over the period from 1980Q1 to 2013Q1, to examine the relationships among house prices and macroeconomic variables. Our empirical results of panel data cointegration tests support the existence of a cointegration among these macroeconomic variables and house prices. Besides, the empirical results of panel DOLS further present that a 1% increase in economic activity, long-term interest rates, and construction costs cause house prices to respectively change 2.16%, -0.04%, and 0.22% in the long run.Furthermore, the increasing economic activity and the construction cost would cause strongerimpacts on the house prices for lower income countries than higher income countries.The results lead to the conclusion that policy of house prices growth can be regarded as economic growth for lower income countries. Finally, in America region, the coefficient of economic activity is the highest, which displays that increasing economic activity causes a faster rise in house prices there than in other regions. There are some special cases whereby the coefficients of interest rates are significantly positive in America and Asia regions.
Abstract: The purpose of my research proposal is to
demonstrate that there is a relationship between EEG and
endometrial cancer.
The above relationship is based on an Aristotelian Syllogism;
since it is known that the 14-3-3 protein is related to the electrical
activity of the brain via control of the flow of Na+ and K+ ions and
since it is also known that many types of cancer are associated with
14-3-3 protein, it is possible that there is a relationship between EEG
and cancer. This research will be carried out by well-defined
diagnostic indicators, obtained via the EEG, using signal processing
procedures and pattern recognition tools such as neural networks in
order to recognize the endometrial cancer type. The current research
shall compare the findings from EEG and hysteroscopy performed on
women of a wide age range. Moreover, this practice could be
expanded to other types of cancer. The implementation of this
methodology will be completed with the creation of an ontology.
This ontology shall define the concepts existing in this research-s
domain and the relationships between them. It will represent the
types of relationships between hysteroscopy and EEG findings.
Abstract: In recent years Operational Transconductance Amplifier based high frequency integrated circuits, filters and systems have been widely investigated. The usefulness of OTAs over conventional OP-Amps in the design of both first order and second order active filters are well documented. This paper discusses some of the tunability issues using the Matlab/Simulink® software which are previously unreported for any commercial OTA. Using the simulation results two first order voltage controlled all pass filters with phase tuning capability are proposed.
Abstract: In conventional seedling production, the seedlings are
being grown in the open field under natural conditions. Here they are
susceptible to sudden changes in climate were their quality and yield
is affected. Quality seedlings are essential for good growth and
performance of crops in main field; they serve as a foundation for the
economic returns to the farmer. Producing quality seedling demands
usage of hybrid seeds as they have the ability to result in better yield,
greater uniformity, improved color, disease resistance, and so forth.
Hybrid seed production poses major operational challenge and its
seed use efficiency plays an important role. Thus in order to
overcome the difficulties currently present in conventional seedling
production and to efficiently use hybrid seeds, ITC Limited Agri
Business Divisions - Sustainability Cell as conceptualized a novel
method of seedling production unit for farmers in West Godavari
District of Andhra Pradesh. The “Green House based Float Seedling"
methodology aims at a protected cultivation technique wherein the
micro climate surrounding the plant/seedling body is controlled
partially or fully as per the requirement of the species. This paper
reports on the techno economic evaluation of green house for
cultivation of float based seedling production with experimental
results that was attained from the pilot implementation in West
Godavari District, Rajahmundry region of India.
Abstract: The Institute of Product Development is dealing
with the development, design and dimensioning of micro components
and systems as a member of the Collaborative Research
Centre 499 “Design, Production and Quality Assurance of
Molded micro components made of Metallic and Ceramic Materials".
Because of technological restrictions in the miniaturization
of conventional manufacturing techniques, shape and
material deviations cannot be scaled down in the same proportion
as the micro parts, rendering components with relatively
wide tolerance fields. Systems that include such components
should be designed with this particularity in mind, often requiring
large clearance. On the end, the output of such systems
results variable and prone to dynamical instability. To save
production time and resources, every study of these effects
should happen early in the product development process and
base on computer simulation to avoid costly prototypes. A
suitable method is proposed here and exemplary applied to a
micro technology demonstrator developed by the CRC499. It
consists of a one stage planetary gear train in a sun-planet-ring
configuration, with input through the sun gear and output
through the carrier. The simulation procedure relies on ordinary
Multi Body Simulation methods and subsequently adds
other techniques to further investigate details of the system-s
behavior and to predict its response. The selection of the relevant
parameters and output functions followed the engineering
standards for regular sized gear trains. The first step is to
quantify the variability and to reveal the most critical points of
the system, performed through a whole-mechanism Sensitivity
Analysis. Due to the lack of previous knowledge about the system-s
behavior, different DOE methods involving small and
large amount of experiments were selected to perform the SA.
In this particular case the parameter space can be divided into
two well defined groups, one of them containing the gear-s profile
information and the other the components- spatial location.
This has been exploited to explore the different DOE techniques
more promptly. A reduced set of parameters is derived for
further investigation and to feed the final optimization process,
whether as optimization parameters or as external perturbation
collective. The 10 most relevant perturbation factors and 4 to 6
prospective variable parameters are considered in a new, simplified
model. All of the parameters are affected by the mentioned
production variability. The objective functions of interest
are based on scalar output-s variability measures, so the
problem becomes an optimization under robustness and reliability constrains. The study shows an initial step on the development
path of a method to design and optimize complex micro
mechanisms composed of wide tolerated elements accounting
for the robustness and reliability of the systems- output.
Abstract: In this study, the density dependent nonlinear reactiondiffusion
equation, which arises in the insect dispersal models, is
solved using the combined application of differential quadrature
method(DQM) and implicit Euler method. The polynomial based
DQM is used to discretize the spatial derivatives of the problem. The
resulting time-dependent nonlinear system of ordinary differential
equations(ODE-s) is solved by using implicit Euler method. The
computations are carried out for a Cauchy problem defined by a onedimensional
density dependent nonlinear reaction-diffusion equation
which has an exact solution. The DQM solution is found to be in a
very good agreement with the exact solution in terms of maximum
absolute error. The DQM solution exhibits superior accuracy at large
time levels tending to steady-state. Furthermore, using an implicit
method in the solution procedure leads to stable solutions and larger
time steps could be used.