Abstract: The in-cylinder flow and mixture formations are
significant in view of today’s increasing concern on environmental
issues and stringent emission regulations. In this paper, the numerical
simulations of a SI engine at different engine speeds (2000-5000
rpm) at fixed intake flow pressure of 1 bar are studied using the AVL
FIRE software. The simulation results show that when the engine
speed at fixed intake flow pressure is increased, the volumetric
efficiency of the engine decreases. This is due to a richer fuel
conditions near the engine cylinder wall when engine speed is
increased. Significant effects of impingement are also noted on the
upper and side walls of the engine cylinder. These variations in
mixture formation before ignition could affect the thermodynamics
efficiency and specific fuel consumption that would lead to a reduced
engine performance.
Abstract: An algorithm is a well-defined procedure that takes
some input in the form of some values, processes them and gives the
desired output. It forms the basis of many other algorithms such as
searching, pattern matching, digital filters etc., and other applications
have been found in database systems, data statistics and processing,
data communications and pattern matching. This paper introduces
algorithmic “Enhanced Bidirectional Selection” sort which is
bidirectional, stable. It is said to be bidirectional as it selects two
values smallest from the front and largest from the rear and assigns
them to their appropriate locations thus reducing the number of
passes by half the total number of elements as compared to selection
sort.
Abstract: Soil erosion is a very complex phenomenon, resulting
from detachment and transport of soil particles by erosion agents.
The kinetic energy of raindrop is the energy available for detachment
and transport by splashing rain. The soil erodibility is defined as the
ability of soil to resist to erosion. For this purpose, an experimental
study was conducted in the laboratory using rainfall simulator to
study the effect of the kinetic energy of rain (Ec) on the soil
erodibility (K). The soil used was a sandy agricultural soil of 62.08%
coarse sand, 19.14% fine sand, 6.39% fine silt, 5.18% coarse silt and
7.21% clay. The obtained results show that the kinetic energy of
raindrops evolves as a power law with soil erodibility.
Abstract: The financial crises caused a collapse in prices of
most asset classes, raising the attention on alternative investments
such as sukuk, a smaller, fast growing but often misunderstood
market. We study diversification benefits of sukuk, their correlation
with other asset classes and the effects of their inclusion in
investment portfolios of institutional and retail investors, through a
comprehensive comparison of their risk/return profiles during and
after the financial crisis.
We find a beneficial performance adjusted for the specific
volatility together with a lower correlation especially during the
financial crisis. The distribution of sukuk returns is positively skewed
and leptokurtic, with a risk/return profile similarly to high yield
bonds. Overall, our results suggest that sukuk present diversification
opportunities, a significant volatility-adjusted performance and lower
correlations especially during the financial crisis.
Our findings are relevant for a number of institutional investors.
Long term investors, such as life insurers would benefit from sukuk’s
protective features during financial crisis yet keeping return and
growth opportunities, whereas banks would gain due to their role of
placers, advisors, market makers or underwriters.
Abstract: Regardless of the manufacturing process used,
subtractive or additive, material, purpose and application, produced
components are conventionally solid mass with more or less complex
shape depending on the production technology selected. Aspects
such as reducing the weight of components, associated with the low
volume of material required and the almost non-existent material
waste, speed and flexibility of production and, primarily, a high
mechanical strength combined with high structural performance, are
competitive advantages in any industrial sector, from automotive,
molds, aviation, aerospace, construction, pharmaceuticals, medicine
and more recently in human tissue engineering. Such features,
properties and functionalities are attained in metal components
produced using the additive technique of Rapid Prototyping from
metal powders commonly known as Selective Laser Melting (SLM),
with optimized internal topologies and varying densities. In order to
produce components with high strength and high structural and
functional performance, regardless of the type of application, three
different internal topologies were developed and analyzed using
numerical computational tools. The developed topologies were
numerically submitted to mechanical compression and four point
bending testing. Finite Element Analysis results demonstrate how
different internal topologies can contribute to improve mechanical
properties, even with a high degree of porosity relatively to fully
dense components. Results are very promising not only from the
point of view of mechanical resistance, but especially through the
achievement of considerable variation in density without loss of
structural and functional high performance.
Abstract: Accounting policies are a set of solutions compliant
with legal regulations that an entity selects and adopts, and which
guarantee a proper quality of financial statements. Those solutions
may differ depending on whether the entity adopts national or
international accounting standards.
The aim of this article is to present accounting principles (policies)
in Polish and international legal regulations and their adoption in
selected Polish companies listed on the Warsaw Stock Exchange. The
research method adopted in this work is the analysis and evaluation
of legal conditions in Polish companies.
Abstract: This paper presents the hardware implemented and
validation for a special system to assist the unprofessional users of
car with back trailers. The system consists of two platforms; the front
car platform (C) and the trailer platform (T). The main objective is to
control the Trailer platform using the actuators found in the front
platform (c). The mobility of the platform (C) is investigated and
inverse and forward kinematics model is obtained for both platforms
(C) and (T).The system is simulated using Matlab M-file and the
simulation examples results illustrated the system performance. The
system is constructed with a hardware setup for the front and trailer
platform. The hardware experimental results and the simulated
examples outputs showed the validation of the hardware setup.
Abstract: An active slat is developed to increase the lift and delay
the separation for a DU96-W180 airfoil. The active slat is a fixed slat
that can be closed, fully opened or intermittently opened by a rotating
vane depending on the need. Experimental results show that the active
slat has reduced the mean pressure and increased the mean velocity
on the suction side of the airfoil for all positive angles of attack,
indicating an increase of lift. The experimental data and numerical
simulations also show that the direction of actuator vane rotation can
influence the mixing of the flow streams on the suction side and
hence influence the aerodynamic performance.
Abstract: A cleaner production project was implemented in a
bakery. The project is based on the substitution of the best available
technique for an obsolete leaven production technology. The new
technology enables production of durable, high-quality leavens.
Moreover, 25% of flour as the original raw material can be replaced
by pastry from the previous day production which has not been sold.
That pastry was previously disposed in a waste incineration plant.
Besides the environmental benefits resulting from less waste, lower
consumption of energy, reduction of sewage waters quantity and
floury dustiness there are also significant economic benefits. Payback
period of investment was calculated with help of static method of
financial analysis about 2.6 years, using dynamic method 3.5 years
and an internal rate of return more than 29%. The supposed annual
average profit after taxationin the second year of operation was
incompliance with the real profit.
Abstract: Images are important source of information used as
evidence during any investigation process. Their clarity and accuracy
is essential and of the utmost importance for any investigation.
Images are vulnerable to losing blocks and having noise added to
them either after alteration or when the image was taken initially,
therefore, having a high performance image processing system and it
is implementation is very important in a forensic point of view. This
paper focuses on improving the quality of the forensic images.
For different reasons packets that store data can be affected,
harmed or even lost because of noise. For example, sending the
image through a wireless channel can cause loss of bits. These types
of errors might give difficulties generally for the visual display
quality of the forensic images.
Two of the images problems: noise and losing blocks are covered.
However, information which gets transmitted through any way of
communication may suffer alteration from its original state or even
lose important data due to the channel noise. Therefore, a developed
system is introduced to improve the quality and clarity of the forensic
images.
Abstract: In the UK, flooding is responsible for significant
losses to the economy due to the impact on businesses, the vast
majority of which are Small and Medium Enterprises (SMEs).
Businesses of this nature tend to lack formal plans to aid their
response to and recovery from disruptive events such as flooding.
This paper reports on work on how an agent-based model (ABM) is
being developed based on interview data gathered from SMEs at-risk
of flooding and/or have direct experience of flooding. The ABM will
enable simulations to be performed allowing investigations of
different response strategies which SMEs may employ to lessen the
impact of flooding, thus strengthening their resilience.
Abstract: Wireless sensor network (WSN) is a network of many interconnected networked systems, they equipped with energy resources and they are used to detect other physical characteristics. On WSN, there are many researches are performed in past decades. WSN applicable in many security systems govern by military and in many civilian related applications. Thus, the security of WSN gets attention of researchers and gives an opportunity for many future aspects. Still, there are many other issues are related to deployment and overall coverage, scalability, size, energy efficiency, quality of service (QoS), computational power and many more. In this paper we discus about various applications and security related issue and requirements of WSN.
Abstract: Particles are the most common and cheapest
reinforcement producing discontinuous reinforced composites with
isotropic properties. Conventional fabrication methods can be used to
produce a wide range of product forms, making them relatively
inexpensive. Optimising composite development must include
consideration of all the fundamental aspect of particles including
their size, shape, volume fraction, distribution and mechanical
properties. Research has shown that the challenges of low fracture
toughness, poor crack growth resistance and low thermal stability can
be overcome by reinforcement with particles. The unique properties
exhibited by micro particles reinforced ceramic composites have
made them to be highly attractive in a vast array of applications.
Abstract: Two Lithium Disilicate (LD) glass ceramics based on
SiO2-Li2O-K2O-Al2O3 system were prepared through a glass melting
method. The glass rods were then fabricated into dental crowns via a
hot pressing at 900˚C and 850˚C in order to study the effect of the
pressing temperatures on the phase formation and microstructure of
the glasses. Different samples of as cast glass and heat treated
samples (600˚C and 700˚C) were used to press for investigating the
effect of an initial microstructure on the hot pressing technique. Xray
diffraction (XRD) and scanning electron microscopy (SEM) were
performed to determine the phase formation and microstructure of the
samples, respectively. XRD results show that the main crystalline
structure was Li2Si2O5 by having Li3PO4, Li0.6Al0.6Si2O6, Li2SiO3,
Ca5 (PO4)3F and SiO2 as minor phases. Glass compositions with
different heat treatment temperatures exhibited a difference phase
formations but have less effect during pressing. SEM micrographs
showed the microstructure of Li2Si2O5 as lath-like shape in all
glasses. With increasing the initial heat treatment temperature, the
longer the lath-like crystals of lithium disilicate were increased
especially when using glass heat treatment at 700˚C followed by
pressing at 900˚C. This could be suggested that LD1 heat treatment at
700˚C which pressing at 900˚C presented the best formation by the
hot pressing and compiled microstructure.
Abstract: To evaluate the factors which predetermine the
coronary artery disease in patients having positive Exercise Tolerance
Test (ETT) that is treadmill results and coronary artery findings. This
descriptive study was conducted at Department of Cardiology,
Ibrahim Cardiac Hospital & Research Institute, Dhaka, Bangladesh
from 1st January, 2014 to 31st August, 2014. All patients who had
done ETT (treadmill) for chest pain diagnosis were studied. One
hundred and four patients underwent coronary angiogram after
positive treadmill result. Patients were divided into two groups
depending upon the angiographic findings, i.e. true positive and false
positive. Positive treadmill test patients who have coronary artery
involvement these are called true positive and who have no
involvement they are called false positive group. Both groups were
compared with each other. Out of 104 patients, 81 (77.9%) patients
had true positive ETT and 23 (22.1%) patients had false positive
ETT. The mean age of patients in positive ETT was 53.46± 8.06
years and male mean age was 53.63±8.36 years and female was
52.87±7.0 years. Sixty nine (85.19%) male patients and twelve
(14.81%) female patients had true positive ETT, whereas 15
(65.21%) males and 8 (34.79%) females had false positive ETT, this
was statistically significant (p
Abstract: The purpose of this study is to compare Self
Compacting Concrete (SCC) and Conventional Concrete (CC) in
terms of their capillary water absorption. During the comparison of
SCC and CC, the effects of two different factors were also
investigated: concrete strength class and curing condition. In the
study, both SCC and CC were produced in three different concrete
classes (C25, C50 and C70) and the other parameter (i.e. curing
condition) was determined as two levels: moisture and air curing. It
was observed that, for both curing environments and all strength
classes of concrete, SCCs had lower capillary water absorption values
than that of CCs. It was also detected that, for both SCC and CC,
capillary water absorption values of samples kept in moisture curing
were significantly lower than that of samples stored in air curing.
Additionally, it was determined that capillary water absorption values
for both SCC and CC decrease with increasing strength class of
concrete for both curing environments.
Abstract: Mammography has been one of the most reliable
methods for early detection of breast cancer. There are different
lesions which are breast cancer characteristic such as
microcalcifications, masses, architectural distortions and bilateral
asymmetry. One of the major challenges of analysing digital
mammogram is how to extract efficient features from it for accurate
cancer classification. In this paper we proposed a hybrid feature
extraction method to detect and classify all four signs of breast
cancer. The proposed method is based on multiscale surrounding
region dependence method, Gabor filters, multi fractal analysis,
directional and morphological analysis. The extracted features are
input to self adaptive resource allocation network (SRAN) classifier
for classification. The validity of our approach is extensively
demonstrated using the two benchmark data sets Mammographic
Image Analysis Society (MIAS) and Digital Database for Screening
Mammograph (DDSM) and the results have been proved to be
progressive.
Abstract: Comprehensive numerical studies have been carried
out to examine the best aerodynamic performance of subsonic aircraft
at different winglet cant angles using a validated 3D k-ω SST model.
In the parametric analytical studies NACA series of airfoils are
selected. Basic design of the winglet is selected from the literature
and flow features of the entire wing including the winglet tip effects
have been examined with different cant angles varying from 150 to
600 at different angles of attack up to 140. We have observed, among
the cases considered in this study that a case, with 150 cant angle the
aerodynamics performance of the subsonic aircraft during takeoff
was found better up to an angle of attack of 2.80 and further its
performance got diminished at higher angles of attack. Analyses
further revealed that increasing the winglet cant angle from 150 to 600
at higher angles of attack could negate the performance deterioration
and additionally it could enhance the peak CL/CD on the order of
3.5%. The investigated concept of variable-cant-angle winglets
appears to be a promising alternative for improving the aerodynamic
efficiency of aircraft.
Abstract: Forging parts is used to automobiles; because, they have high strength and it is possible to press them into complicated shape. When itis possible to manufacture hollow forging parts, it leads to reduce weightof the automobiles. But, hollow forging parts are confined to axisymmetrical shape. Hollowforging parts that were pressed to complicated shape are expected. Therefore, we forge a blank that aluminum alloy was inserted in stainless steel. After that, we can providecomplex forging parts that are reduced weight,ifit is possible to be melted the aluminum alloy away by using different of melting points.It is necessary to establish heat forging analysis methodon blank consist of stainless steel and aluminum alloy. Because,this forging is different from conventional forging and this technology is not confirmed. In this study, we compared forging experiment with numerical analysis on the view point of forming load and shape after forming and establish how to set the material temperaturesof two metals and material property of stainless steel on the analysis method. Consequently, temperature difference of stainless steel and aluminum alloy was obtained by experiment. We got material property of stainless steel on forging experimental by compression tests. We had compared numerical analysis that was used the temperature difference of two metals and the material property of stainless steel on forging experimental with forging experiment. Forging analysis method on blankconsist of two metals was established by result of numerical analysis having agreedwith result of forging experiment.
Abstract: This paper illustrates the effect of nano Magnesium
Hydroxide (MH) loading on the thermal properties of Low Density
Polyethylene (LDPE)/Poly (ethylene-co vinyl acetate) (EVA) nano
composite. Thermal studies were conducted, as it understanding is
vital for preliminary development of new polymeric systems.
Thermal analysis of nanocomposite was conducted using thermo
gravimetric analysis (TGA), and differential scanning calorimetry
(DSC). Major finding of TGA indicated two main stages of
degradation process found at (350 ± 25oC) and (480 ± 25oC)
respectively. Nano metal filler expressed better fire resistance as it
stand over high degree of temperature. Furthermore, DSC analysis
provided a stable glass temperature around 51 (±1oC) and captured
double melting point at 84 (±2oC) and 108 (±2oC). This binary
melting point reflects the modification of nano filler to the polymer
matrix forming melting crystals of folded and extended chain. The
percent crystallinity of the samples grew vividly with increasing filler
content. Overall, increasing the filler loading improved the
degradation temperature and weight loss evidently and a better
process and phase stability was captured in DSC.