Abstract: Preparation of nanoparticles of cerium oxide and
adsorption of bovine serum albumin on them were studied. Particle
size distribution and influence of pH on zeta potential of prepared
CeO2 were determined. Average size of prepared cerium oxide
nanoparticles was 9 nm. The simultaneous measurements of the
bovine serum albumin adsorption and zeta potential determination of
the (adsorption) suspensions were carried out. The adsorption
isotherms were found to be of typical Langmuir type; values of the
bovine serum albumin adsorption capacities were calculated.
Increasing of pH led to decrease of zeta potential and decrease of
adsorption capacity of cerium oxide nanoparticles. The maximum
adsorption capacity was found for strongly acid suspension (am =
118 mg/g). The samples of nanoceria with positive zeta potential
adsorbed more bovine serum albumin on the other hand, the samples
with negative zeta potential showed little or no protein adsorption.
Surface charge or better say zeta potential of CeO2 nanoparticles
plays the key role in adsorption of proteins on such type of materials.
Abstract: Pavement surface unevenness plays a pivotal role on
roughness index of road which affects on riding comfort ability.
Comfort ability refers to the degree of protection offered to vehicle
occupants from uneven elements in the road surface. So, it is
preferable to have a lower roughness index value for a better riding
quality of road users. Roughness is generally defined as an
expression of irregularities in the pavement surface which can be
measured using different equipments like MERLIN, Bump integrator,
Profilometer etc. Among them Bump Integrator is quite simple and
less time consuming in case of long road sections. A case study is
conducted on low volume roads in West District in Tripura to
determine roughness index (RI) using Bump Integrator at the
standard speed of 32 km/h. But it becomes too tough to maintain the
requisite standard speed throughout the road section. The speed of
Bump Integrator (BI) has to lower or higher in some distinctive
situations. So, it becomes necessary to convert these roughness index
values of other speeds to the standard speed of 32 km/h. This paper
highlights on that roughness index conversional model. Using SPSS
(Statistical Package of Social Sciences) software a generalized
equation is derived among the RI value at standard speed of 32 km/h
and RI value at other speed conditions.
Abstract: The thermo-mechanical behaviour of concrete energy
pile foundations with different single and double U-tube shapes
incorporated was analysed using the Comsol Multi-physics package.
For the analysis, a 3D numerical model in real scale of the concrete
pile and surrounding soil was simulated regarding actual operation of
ground heat exchangers (GHE) and the surrounding ambient
temperature. Based on initial ground temperature profile measured in
situ, tube inlet temperature was considered to range from 6oC to 0oC
(during the contraction process) over a 30-day period. Extra thermal
stresses and deformations were calculated during the simulations and
differences arising from the use of two different systems (single-tube
and double-tube) were analysed. The results revealed no significant
difference for extra thermal stresses at the centre of the pile in either
system. However, displacements over the pile length were found to
be up to 1.5-fold higher in the double-tube system than the singletube
system.
Abstract: This paper discusses about the findings of preliminary
survey on MATLAB software learning among power electronics
students. One of the main focuses of power electronics course is on
DC to DC boost convertors, because boost convertors are generally
used in different industrial and non industrial applications. Population
samples of this study were randomly selected final year bachelor of
electronics and electrical engineering students from University Tun
Hussein Onn Malaysia (UTHM).As per the results from the survey
questioner analysis, almost eighty percent students are facing
problem and difficulties in Dc to Dc boost convertors experimental
understanding without using MATLAB simulink package. As per
finding of this study it is clear that MATLAB play an effective and
efficient function for better understanding of boost convertors
experimental work among power electronics learners.
Abstract: This paper explains about the voltage output for DC to
DC boost converter between open loop, PID controller and fuzzy
logic controller through Matlab Simulink. Simulink input voltage was
set at 12V and the voltage reference was set at 24V. The analysis on
the deviation of voltage resulted that the difference between reference
voltage setting and the output voltage is always lower. Comparison
between open loop, PID and FLC shows that, the open loop circuit
having a bit higher on the deviation of voltage. The PID circuit
boosts for FLC has a lesser deviation of voltage and proved that it is
such a better performance on control the deviation of voltage during
the boost mode.
Abstract: There are pending discussions over the mapping of
country export potential in order to refocus export strategy of firms
and its evidence-based promotion by the Export Credit Agencies
(ECAs) and other permitted vehicles of governments.
In this paper we develop our version of an applied model that
offers “stepwise” elimination of unattractive markets. We modify and
calibrate the model for the particular features of the Czech Republic
and specific pilot cases where we apply an individual approach to
each sector.
Abstract: A computational fluid dynamics simulation is done for
non-Newtonian fluid in a baffled stirred tank. The CMC solution is
taken as non-Newtonian shear thinning fluid for simulation. The
Reynolds Average Navier Stocks equation with steady state multi
reference frame approach is used to simulate flow in the stirred tank.
The turbulent flow field is modelled using realizable k-ε turbulence
model. The simulated velocity profiles of Rushton turbine is
validated with literature data. Then, the simulated flow field of CD-6
impeller is compared with the Rushton turbine. The flow field
generated by CD-6 impeller is less in magnitude than the Rushton
turbine. The impeller global parameter, power number and flow
number, and entropy generation due to viscous dissipation rate is also
reported.
Abstract: The use of information and communication
technologies such as computers, mobile phones and the Internet is
becoming prevalent in today’s world; and it is facilitating access to a
vast amount of data, services and applications for the improvement of
people’s lives. However, this prevalence of ICTs is hampered by the
problem of low income levels in developing countries to the point
where people cannot timeously replace or repair their ICT devices
when damaged or lost; and this problem serves as a motivation for
this study whose aim is to examine the perceptions of teachers on the
reliability of cellphones when used for teaching and learning
purposes. The research objectives unfolding this aim are of two
types: Objectives on the selection and design of theories and models,
and objectives on the empirical testing of these theories and models.
The first type of objectives is achieved using content analysis in an
extensive literature survey: and the second type of objectives is
achieved through a survey of high school teachers from the ILembe
and UMgungundlovu districts in the KwaZulu-Natal province of
South Africa. Data collected from this questionnaire based survey is
analysed in SPSS using descriptive statistics and Pearson correlations
after checking the reliability and validity of the questionnaires. The
main hypothesis driving this study is that there is a relationship
between the demographics and the attribution identity of teachers on
one hand, and their perceptions on the reliability of cellphones on the
other hand, as suggested by existing literature; except that attribution
identities are considered in this study under three angles: intention,
knowledge and ability, and action. The results of this study confirm
that the perceptions of teachers on the reliability of cellphones for
teaching and learning are affected by the school location of these
teachers, and by their perceptions on learners’ cellphones usage
intentions and actual use.
Abstract: At-site flood frequency analysis is used to estimate
flood quantiles when at-site record length is reasonably long. In
Australia, FLIKE software has been introduced for at-site flood
frequency analysis. The advantage of FLIKE is that, for a given
application, the user can compare a number of most commonly
adopted probability distributions and parameter estimation methods
relatively quickly using a windows interface. The new version of
FLIKE has been incorporated with the multiple Grubbs and Beck test
which can identify multiple numbers of potentially influential low
flows. This paper presents a case study considering six catchments in
eastern Australia which compares two outlier identification tests
(original Grubbs and Beck test and multiple Grubbs and Beck test)
and two commonly applied probability distributions (Generalized
Extreme Value (GEV) and Log Pearson type 3 (LP3)) using FLIKE
software. It has been found that the multiple Grubbs and Beck test
when used with LP3 distribution provides more accurate flood
quantile estimates than when LP3 distribution is used with the
original Grubbs and Beck test. Between these two methods, the
differences in flood quantile estimates have been found to be up to
61% for the six study catchments. It has also been found that GEV
distribution (with L moments) and LP3 distribution with the multiple
Grubbs and Beck test provide quite similar results in most of the
cases; however, a difference up to 38% has been noted for flood
quantiles for annual exceedance probability (AEP) of 1 in 100 for one
catchment. This finding needs to be confirmed with a greater number
of stations across other Australian states.
Abstract: Present study is aimed on the cutting process of circular
cross-section rods where the fracture is used to separate one rod
into two pieces. Incorporating the phenomenological ductile fracture
model into the explicit formulation of finite element method, the
process can be analyzed without the necessity of realizing too many
real experiments which could be expensive in case of repetitive
testing in different conditions. In the present paper, the steel AISI
1045 was examined and the tensile tests of smooth and notched
cylindrical bars were conducted together with biaxial testing of the
notched tube specimens to calibrate material constants of selected
phenomenological ductile fracture models. These were implemented
into the Abaqus/Explicit through user subroutine VUMAT and used
for cutting process simulation. As the calibration process is based
on variables which cannot be obtained directly from experiments,
numerical simulations of fracture tests are inevitable part of the
calibration. Finally, experiments regarding the cutting process were
carried out and predictive capability of selected fracture models is
discussed. Concluding remarks then make the summary of gained
experience both with the calibration and application of particular
ductile fracture criteria.
Abstract: Self-service technologies (SSTs) make an important
contribution to the daily life of people nowadays. However, the
introduction of SST does not lead to its usage. Thereby, this paper
was an attempt on discovery of the most preferred SST in the
customers’ point of view. To fulfill this aim, the Analytical Hierarchy
Process (AHP) was applied based on Saaty’s questionnaire which
was administered to the customers of e-banking services located in
Golestan providence, northern Iran. This study used qualitative
factors in association with the intention of consumers’ usage of SSTs
to rank three SSTs: ATM, mobile banking and internet banking. The
results showed that mobile banking get the highest weight in
consumers’ point of view. This research can be useful both for
managers and service providers and also for customers who intend to
use e-banking.
Abstract: This paper deals with the problem of automatic rule
generation for fuzzy systems design. The proposed approach is based
on hybrid artificial bee colony (ABC) optimization and weighted least
squares (LS) method and aims to find the structure and parameters of
fuzzy systems simultaneously. More precisely, two ABC based fuzzy
modeling strategies are presented and compared. The first strategy
uses global optimization to learn fuzzy models, the second one
hybridizes ABC and weighted least squares estimate method. The
performances of the proposed ABC and ABC-LS fuzzy modeling
strategies are evaluated on complex modeling problems and compared
to other advanced modeling methods.
Abstract: The aim of this study is to determine the effect of age
and physiological status on progesterone and energy metabolism of
Ouled Djellal (O.D) breed ewes. 40 healthy ewes were divided into
two groups, primiparous and multiparous, with 20 ewes in each
group. The body weights (BW) (Kg) were 46.6 ± 4.20 and 59.2 ±
3.02, and consuming less 25 to 30% of their basal energetic
requirements. The values of serum glucose, triglycerides and
cholesterol were lower in pregnant than in non-pregnant ewes. The
high to very high significant differences were found during the 15th
week of pregnancy for glycaemia and triglyceridemia respectively.
Concerning serum progesterone, a very highly significant difference
(p
Abstract: Drying behavior of blanched sweet potato in a cabinet
dryer using different five air temperatures (40-80°C) and ten sweet
potato varieties sliced to 5mm thickness were investigated. The
drying data were fitted to eight models. The Modified Henderson and
Pabis model gave the best fit to the experimental moisture ratio data
obtained during the drying of all the varieties while Newton (Lewis)
and Wang and Singh models gave the least fit. The values of Deff
obtained for Bophelo variety (1.27 x 10-9 to 1.77 x 10-9 m2/s) was
the least while that of S191 (1.93 x 10-9 to 2.47 x 10-9 m2/s) was the
highest which indicates that moisture diffusivity in sweet potato is
affected by the genetic factor. Activation energy values ranged from
0.27-6.54 kJ/mol. The lower activation energy indicates that drying
of sweet potato slices requires less energy and is hence a cost and
energy saving method. The drying behavior of blanched sweet potato
was investigated in a cabinet dryer. Drying time decreased
considerably with increase in hot air temperature. Out of the eight
models fitted, the Modified Henderson and Pabis model gave the best
fit to the experimental moisture ratio data on all the varieties while
Newton, Wang and Singh models gave the least. The lower activation
energy (0.27 - 6.54 kJ/mol) obtained indicates that drying of sweet
potato slices requires less energy and is hence a cost and energy
saving method.
Abstract: This paper is drawn from a wider study of the
management of gender, age and disability diversity in the banking
sector in the Kingdom of Saudi Arabia (KSA), which aims to develop
a framework for diversity management (DM) in this sector. The
paper focuses on the management of disability diversity. The purpose
of the paper is to assist in understanding disability DM in the banking
sector in KSA and to make suggestions for its enhancement. Hence, it
contributes to filling a research gap, as there is a dearth of literature
on disability DM, in KSA in general, and in the banking sector
specifically.
Discrimination against people with disabilities is a social issue that
has not been entirely overcome in any society. However, in KSA,
Islam informs almost every aspect of daily life including work, and
Islam is against discrimination. Hence, in KSA, there are regulations
to accommodate people with disabilities; however, employers are still
free not to hire job applicants with disabilities specifically because of
their condition. Indeed, disabled people are almost entirely absent
from the labour market.
There are 12 Saudi-owned or part-Saudi-owned banks in KSA and
two managers from each of these were interviewed, making a total of
24. The interviews aimed to investigate empirically the understanding
of managers in the banking sector in KSA of diversity management,
including disability DM, in the banking sector. The interview data
were analysed using thematic analysis. Two interviewees stated that
banks used the employment of people with disabilities to enhance
their corporate image, while five expressed the opinion that disabled
employees could contribute to the bank provided they did not have to
deal with customers face-to-face. Nine of the interviewees perceived
that disabled employees could be of value to the bank for their own
sake, not only in ‘behind the scenes’ roles. Another two interviewees
mentioned that employing disabled people could be part of the bank’s
community service programme and one thought it would be part of
the bank’s Saudisation efforts. The remaining five interviewees did
not know how disabled people could contribute to the bank.
The findings show that disability DM in the banking sector in
KSA is a relatively new concept, and is not yet well understood. In
the light of the findings, in order to achieve the purpose of the paper,
the following suggestions were made for the enhancement of
disability DM in the banking sector in KSA. A change in attitudes
towards disabled people is necessary. Such a change in the workplace
can only be achieved if a top-down approach is taken to the
integration of disabled people. Hence, it is suggested that
management and employees follow a course in disability awareness.
Further, a diversity officer in the HR department could enhance the
integration of disabled people into the banking workforce. It is also
suggested that greater government support is required through closely
monitored and enforced anti-discrimination legislation. Moreover,
flexible working arrangements such as part-time work would
facilitate the employment of disabled people and benefit other groups
of employees.
Abstract: In today’s world, the LED display has been used for
presenting visual information under various circumstances. Such
information is an important intermediary in the human information
processing. Researchers have been investigated diverse factors that
influence this process effectiveness. The letter size is undoubtedly
one major factor that has been tested and recommended by many
standards and guidelines. However, viewing information on the
display from direct perpendicular position is a typical assumption
whereas many actual events are required viewing from the angles.
This current research aims to study the effect of oblique viewing
angle and viewing distance on ability to recognize alphabet, number,
and English word. The total of ten participants was volunteered to our
3 x 4 x 4 within subject study. Independent variables include three
distance levels (2, 6, and 12 m), four oblique angles (0, 45, 60, 75
degree), and four target types (alphabet, number, short word, and
long word). Following the method of constant stimuli our study
suggests that the larger oblique angle, ranging from 0 to 75 degree
from the line of sight, results in significant higher legibility threshold
or larger font size required (p-value < 0.05). Viewing distance factor
also shows to have significant effect on the threshold (p-value
Abstract: We introduced an all-optical multicasting
characteristics with wavelength conversion based on a novel
all-optical triode using negative feedback semiconductor optical
amplifier. This study was demonstrated with a transfer speed of 10
Gb/s to a non-return zero 231-1 pseudorandom bit sequence system.
This multi-wavelength converter device can simultaneously provide
three channels of output signal with the support of non-inverted and
inverted conversion. We studied that an all-optical multicasting and
wavelength conversion accomplishing cross gain modulation is
effective in a semiconductor optical amplifier which is effective to
provide an inverted conversion thus negative feedback. The
relationship of received power of back to back signal and output
signals with wavelength 1535 nm, 1540 nm, 1545 nm, 1550 nm, and
1555 nm with bit error rate was investigated. It was reported that the
output signal wavelengths were successfully converted and modulated
with a power penalty of less than 8.7 dB, which the highest is 8.6 dB
while the lowest is 4.4 dB. It was proved that all-optical multicasting
and wavelength conversion using an optical triode with a negative
feedback by three channels at the same time at a speed of 10 Gb/s is a
promising device for the new wavelength conversion technology.
Abstract: The substantial similarity of fatigue mechanism in a
new test rig for rolling contact fatigue (RCF) has been investigated. A
new reduced-scale test rig is designed to perform controlled RCF
tests in wheel-rail materials. The fatigue mechanism of the rig is
evaluated in this study using a combined finite element-fatigue
prediction approach. The influences of loading conditions on fatigue
crack initiation have been studied. Furthermore, the effects of some
artificial defects (squat-shape) on fatigue lives are examined. To
simulate the vehicle-track interaction by means of the test rig, a threedimensional
finite element (FE) model is built up. The nonlinear
material behaviour of the rail steel is modelled in the contact
interface. The results of FE simulations are combined with the critical
plane concept to determine the material points with the greatest
possibility of fatigue failure. Based on the stress-strain responses, by
employing of previously postulated criteria for fatigue crack initiation
(plastic shakedown and ratchetting), fatigue life analysis is carried
out. The results are reported for various loading conditions and
different defect sizes. Afterward, the cyclic mechanism of the test rig
is evaluated from the operational viewpoint. The results of fatigue
life predictions are compared with the expected number of cycles of
the test rig by its cyclic nature. Finally, the estimative duration of the
experiments until fatigue crack initiation is roughly determined.
Abstract: A new small–scale test rig developed for rolling
contact fatigue (RCF) investigations in wheel–rail material. This
paper presents the scaling strategy of the rig based on dimensional
analysis and mechanical modelling. The new experimental rig is
indeed a spinning frame structure with multiple wheel components
over a fixed rail-track ring, capable of simulating continuous wheelrail
contact in a laboratory scale. This paper describes the
dimensional design of the rig, to derive its overall scaling strategy
and to determine the key elements’ specifications. Finite element
(FE) modelling is used to simulate the mechanical behavior of the rig
with two sample scale factors of 1/5 and 1/7. The results of FE
models are compared with the actual railway system to observe the
effectiveness of the chosen scales. The mechanical properties of the
components and variables of the system are finally determined
through the design process.
Abstract: One of the most important tasks in the risk
management is the correct determination of probability of default
(PD) of particular financial subjects. In this paper a possibility of
determination of financial institution’s PD according to the creditscoring
models is discussed. The paper is divided into the two parts.
The first part is devoted to the estimation of the three different
models (based on the linear discriminant analysis, logit regression
and probit regression) from the sample of almost three hundred US
commercial banks. Afterwards these models are compared and
verified on the control sample with the view to choose the best one.
The second part of the paper is aimed at the application of the chosen
model on the portfolio of three key Czech banks to estimate their
present financial stability. However, it is not less important to be able
to estimate the evolution of PD in the future. For this reason, the
second task in this paper is to estimate the probability distribution of
the future PD for the Czech banks. So, there are sampled randomly
the values of particular indicators and estimated the PDs’ distribution,
while it’s assumed that the indicators are distributed according to the
multidimensional subordinated Lévy model (Variance Gamma model
and Normal Inverse Gaussian model, particularly). Although the
obtained results show that all banks are relatively healthy, there is
still high chance that “a financial crisis” will occur, at least in terms
of probability. This is indicated by estimation of the various quantiles
in the estimated distributions. Finally, it should be noted that the
applicability of the estimated model (with respect to the used data) is
limited to the recessionary phase of the financial market.