Abstract: In this paper, the transient device performance analysis
of n-type Gate Inside JunctionLess Transistor (GI-JLT) has been
evaluated. 3-D Bohm Quantum Potential (BQP) transport device
simulation has been used to evaluate the delay and power dissipation
performance. GI-JLT has a number of desirable device parameters
such as reduced propagation delay, dynamic power dissipation,
power and delay product, intrinsic gate delay and energy delay
product as compared to Gate-all-around transistors GAA-JLT. In
addition to this, various other device performance parameters namely,
on/off current ratio, short channel effects (SCE), transconductance
Generation Factor (TGF) and unity gain cut-off frequency (fT ) and
subthreshold slope (SS) of the GI-JLT and GAA-JLT have been
analyzed and compared. GI-JLT shows better device performance
characteristics than GAA-JLT for low power and high frequency
applications, because of its larger gate electrostatic control on the
device operation.
Abstract: In view of a possible application in optical data
storage devices, diffraction grating efficiency of an organic dye, Acid
Fuchsin doped in PMMA matrix was studied under excitation with
CW diode pumped Nd: YAG laser at 532 nm. The open aperture Zscan
of dye doped polymer displayed saturable absorption and the
closed aperture Z-scan of the samples exhibited negative
nonlinearity. The diffraction efficiency of the grating is the ratio of
the intensity of the first order diffracted power to the incident read
beam power. The dye doped polymer films were found to be good
media for recording. It is observed that the formation of gratings
strongly depend on the concentration of dye in the polymer film, the
intensity ratios of the writing beams and the angle between the
writing beams. It has been found that efficient writing can be made at
an angle of 20o and when the intensity ratio of the writing beams is
unity.
Abstract: The objective of this research is to design and
construct the PV-Wind hybrid autonomous system for the greenhouse
plantation, and analyze the technical performance of the PV-Wind
energy system. This design depends on the water consumption in the
greenhouse by using 24 of the fogging mist each with the capability
of 24 liter/min. The operating time is 4 times per day, each round for
15 min. The fogging system is being driven by water pump with AC
motor rating 0.5 hp. The load energy consumed is around 1.125
kWh/d. The designing results of the PV-Wind hybrid energy system
is that sufficient energy could be generated by this system. The
results of this study can be applied as a technical data reference for
other areas in the central part of Thailand.
Abstract: Recently, increasing the quality of experience (QoE) is
an important issue. Since performance degradation at cell edge
extremely reduces the QoE, several techniques are defined at
LTE/LTE-A standard to remove inter-cell interference (ICI). However,
the conventional techniques have disadvantage because there is a
trade-off between resource allocation and reliable communication.
The proposed scheme reduces the ICI more efficiently by using
channel state information (CSI) smartly. It is shown that the proposed
scheme can reduce the ICI with fewer resources.
Abstract: Auckland has a temperate climate with comfortable warm, dry summers and mild, wet winters. An Auckland school normally does not need air conditioning for cooling during the summer and only needs heating during the winter. The Auckland school building thermal design should more focus on winter thermal performance and indoor thermal comfort for energy efficiency. This field study of testing indoor and outdoor air temperatures, relative humidity and indoor surface temperatures of three classrooms with different envelopes were carried out in the Avondale College during the winter months in 2013. According to the field study data, this study is to compare and evaluate winter thermal performance and indoor thermal conditions of school buildings with different envelopes.
Abstract: Wireless mesh networking is rapidly gaining in
popularity with a variety of users: from municipalities to enterprises,
from telecom service providers to public safety and military
organizations. This increasing popularity is based on two basic facts:
ease of deployment and increase in network capacity expressed in
bandwidth per footage; WMNs do not rely on any fixed
infrastructure. Many efforts have been used to maximizing
throughput of the network in a multi-channel multi-radio wireless
mesh network. Current approaches are purely based on either static or
dynamic channel allocation approaches. In this paper, we use a
hybrid multichannel multi radio wireless mesh networking
architecture, where static and dynamic interfaces are built in the
nodes. Dynamic Adaptive Channel Allocation protocol (DACA), it
considers optimization for both throughput and delay in the channel
allocation. The assignment of the channel has been allocated to be codependent
with the routing problem in the wireless mesh network and
that should be based on passage flow on every link. Temporal and
spatial relationship rises to re compute the channel assignment every
time when the pattern changes in mesh network, channel assignment
algorithms assign channels in network. In this paper a computing
path which captures the available path bandwidth is the proposed
information and the proficient routing protocol based on the new path
which provides both static and dynamic links. The consistency
property guarantees that each node makes an appropriate packet
forwarding decision and balancing the control usage of the network,
so that a data packet will traverse through the right path.
Abstract: Worldwide, most PILC MV underground cables in use
are approaching the end of their design life; hence, failures are likely
to increase. This paper studies the electric field and potential
distributions within the PILC insulted cable containing common
void-defect. The finite element model of the performance of the
belted PILC MV underground cable is presented. The variation of the
electric field stress within the cable using the Finite Element Method
(FEM) is concentrated. The effects of the void-defect within the
insulation are given. Outcomes will lead to deeper understanding of
the modeling of Paper Insulated Lead Covered (PILC) and electric
field response of belted PILC insulted cable containing void defect.
Abstract: Evaluating the performance of a simulator in the
CAVE has to be confirmed by encouraging people to live the
experience of virtual reality. In this paper, a detailed procedure of
recording video is presented. Limitations of the experimental device
are firstly exposed. Then, solutions for improving this idea are finally
described.
Abstract: In this paper a new algorithm to generate random
simple polygons from a given set of points in a two dimensional
plane is designed. The proposed algorithm uses a genetic algorithm to
generate polygons with few vertices. A new merge algorithm is
presented which converts any two polygons into a simple polygon.
This algorithm at first changes two polygons into a polygonal chain
and then the polygonal chain is converted into a simple polygon. The
process of converting a polygonal chain into a simple polygon is
based on the removal of intersecting edges. The experiments results
show that the proposed algorithm has the ability to generate a great
number of different simple polygons and has better performance in
comparison to celebrated algorithms such as space partitioning and
steady growth.
Abstract: The main aim of a communication system is to
achieve maximum performance. In Cognitive Radio any user or
transceiver has ability to sense best suitable channel, while channel is
not in use. It means an unlicensed user can share the spectrum of a
licensed user without any interference. Though, the spectrum sensing
consumes a large amount of energy and it can reduce by applying
various artificial intelligent methods for determining proper spectrum
holes. It also increases the efficiency of Cognitive Radio Network
(CRN). In this survey paper we discuss the use of different learning
models and implementation of Artificial Neural Network (ANN) to
increase the learning and decision making capacity of CRN without
affecting bandwidth, cost and signal rate.
Abstract: Karst term is the determiner of a variety of areas or
landforms and unique perspectives that have been formed in result of
the of the ingredients dissolution of rocks constituter by natural
waters. Shiraz area with an area of 5322km2 is located in the simple
folded belt in the southern part of Zagros Mountain of Fars, and is
surrounded with Limestone Mountains (Asmari formation). Shiraz
area is located in Calcareous areas. The infrastructure of this city is
lime and absorbing wells that the city can influence the Limestone
dissolution and those accelerate its rate and increase the cavitation
below the surface. Dasht-e Arjan is a graben, which has been created
as the result of activity of two normal faults in its east and west sides.
It is a complete sample of Karst plains (Polje) which has been created
with the help of tectonic forces (fault) and dissolution process of
water in Asmari limestone formation. It is located 60km. off south
west of Shiraz (on Kazeroon-Shiraz road). In 1971, UNESCO has
recognized this plain as a reserve of biosphere. It is considered as one
of the world’s most beautiful geological phenomena, so that most of
the world’s geologists are interested in visiting this place. The
purpose of this paper is to identify and introduce landscapes of Karst
features shiraz city and Dasht-e Arjan including Karst dissolution
features (Lapiez, Karst springs, dolines, caves, underground caves,
ponors, and Karst valleys), anticlines and synclines, and Arjan Lake.
Abstract: In this study, data loss tolerance of Support Vector Machines (SVM) based activity recognition model and multi activity classification performance when data are received over a lossy wireless sensor network is examined. Initially, the classification algorithm we use is evaluated in terms of resilience to random data loss with 3D acceleration sensor data for sitting, lying, walking and standing actions. The results show that the proposed classification method can recognize these activities successfully despite high data loss. Secondly, the effect of differentiated quality of service performance on activity recognition success is measured with activity data acquired from a multi hop wireless sensor network, which introduces high data loss. The effect of number of nodes on the reliability and multi activity classification success is demonstrated in simulation environment. To the best of our knowledge, the effect of data loss in a wireless sensor network on activity detection success rate of an SVM based classification algorithm has not been studied before.
Abstract: Testing the first year students of Informatics at the
University of Debrecen revealed that students start their tertiary
studies in programming with a low level of programming knowledge
and algorithmic skills. The possible reasons which lead the students
to this very unfortunate result were examined. The results of the test
were compared to the students’ results in the school leaving exams
and to their self-assessment values. It was found that there is only a
slight connection between the students’ results in the test and in the
school leaving exams, especially at intermediate level. Beyond this,
the school leaving exams do not seem to enable students to evaluate
their own abilities.
Abstract: In the scope of application of technical textiles, Non-
Crimp Fabrics are increasingly used. In general, NCF exhibit
excellent load bearing properties, but caused by the manufacturing
process, there are some remaining disadvantages which have to be
reduced. Regarding to this, a novel technique of processing NCF was
developed substituting the binding-thread by an adhesive. This stitchfree
method requires new manufacturing concept as well as new basic
methods to prove adhesion of glue at fibres and textiles. To improve
adhesion properties and the wettability of carbon-fibres by the
adhesive, oxy-fluorination was used. The modification of carbonfibres
by oxy-fluorination was investigated via scanning electron
microscope, X-ray photoelectron spectroscopy and single fibre
tensiometry. Special tensile tests were developed to determine the
maximum force required for detachment.
Abstract: In-memory database systems are becoming popular
due to the availability and affordability of sufficiently large RAM and
processors in modern high-end servers with the capacity to manage
large in-memory database transactions. While fast and reliable inmemory
systems are still being developed to overcome cache misses,
CPU/IO bottlenecks and distributed transaction costs, disk-based data
stores still serve as the primary persistence. In addition, with the
recent growth in multi-tenancy cloud applications and associated
security concerns, many organisations consider the trade-offs and
continue to require fast and reliable transaction processing of diskbased
database systems as an available choice. For these
organizations, the only way of increasing throughput is by improving
the performance of disk-based concurrency control. This warrants a
hybrid database system with the ability to selectively apply an
enhanced disk-based data management within the context of inmemory
systems that would help improve overall throughput.
The general view is that in-memory systems substantially
outperform disk-based systems. We question this assumption and
examine how a modified variation of access invariance that we call
enhanced memory access, (EMA) can be used to allow very high
levels of concurrency in the pre-fetching of data in disk-based
systems. We demonstrate how this prefetching in disk-based systems
can yield close to in-memory performance, which paves the way for
improved hybrid database systems. This paper proposes a novel EMA
technique and presents a comparative study between disk-based EMA
systems and in-memory systems running on hardware configurations
of equivalent power in terms of the number of processors and their
speeds. The results of the experiments conducted clearly substantiate
that when used in conjunction with all concurrency control
mechanisms, EMA can increase the throughput of disk-based systems
to levels quite close to those achieved by in-memory system. The
promising results of this work show that enhanced disk-based
systems facilitate in improving hybrid data management within the
broader context of in-memory systems.
Abstract: Proof of controlling crack width is a basic condition
for securing suitable performance in serviceability limit state. The
cracking in concrete can occur at any time from the casting of time to
the years after the concrete has been set in place. Most codes struggle
with offering procedure for crack width calculation. There is lack in
availability of design charts for designers to compute crack width
with ease. The focus of the study is to utilize design charts and
parametric equations in calculating crack width with minimum error.
The paper contains a simplified procedure to calculate crack width
for reinforced concrete (RC) sections subjected to bending with axial
tensile force following the guidelines of Euro code [DS EN-1992-1-1
& DS EN-1992-1-2]. Numerical examples demonstrate the
application of the suggested procedure. Comparison with parallel
analytical tools supports the validity of result and show the
percentage deviation of crack width in both the procedures. The
technique is simple, user friendly and ready to evolve for a greater
spectrum of section sizes and materials.
Abstract: An efficient and green method for oxidation of thiols
to the corresponding disulfides is reported using ionic liquid
[HSO3N(C2H4OSO3H)3] in the presence of free nano-Fe2O3 at 60°C.
Ionic liquid is selective oxidant for S-S Coupling variety aliphatic
and aromatic of thiols to corresponding disulfide in the presence of
free nano-Fe2O3 as recoverable catalyst. Reaction has been performed
in methanol as an inexpensive solvent. This reaction is clean and easy
work-up with no side reaction.
Abstract: Electric vehicles are one of the most complicated
electric devices to simulate due to the significant number of different
processes involved in electrical structure of it. There are concurrent
processes of energy consumption and generation with different
onboard systems, which make simulation tasks more complicated to
perform. More accurate simulation on energy consumption can
provide a better understanding of all energy management for electric
transport. As a result of all those processes, electric transport can
allow for a more sustainable future and become more convenient in
relation to the distance range and recharging time. This paper
discusses the problems of energy consumption simulations for
electric vehicles using different software packages to provide ideas
on how to make this process more precise, which can help engineers
create better energy management strategies for electric vehicles.
Abstract: The purpose of this study is to examine the possible
link between employee and customer satisfaction. The service
provided by employees, help to build a good relationship with
customers and can help at increasing their loyalty. Published data for
job satisfaction and indicators of customer services of banks were
gathered from relevant published works which included data from
five different countries. The scores of customers and employees
satisfaction of the different published works were transformed and
normalized to the scale of 1 to 100. The data were analyzed and a
regression analysis of the two parameters was used to describe the
link between employee’s satisfaction and customer’s satisfaction.
Assuming that employee satisfaction has a significant influence on
customer’s service and the resulting customer satisfaction, the
reviewed data indicate that employee’s satisfaction contributes
significantly on the level of customer satisfaction in the Banking
sector. There was a significant correlation between the two
parameters (Pearson correlation R2=0.52 P
Abstract: Web-based Cognitive Writing Instruction (WeCWI)’s
contribution towards language development can be divided into
linguistic and non-linguistic perspectives. In linguistic perspective,
WeCWI focuses on the literacy and language discoveries, while the
cognitive and psychological discoveries are the hubs in non-linguistic
perspective. In linguistic perspective, WeCWI draws attention to free
reading and enterprises, which are supported by the language
acquisition theories. Besides, the adoption of process genre approach
as a hybrid guided writing approach fosters literacy development.
Literacy and language developments are interconnected in the
communication process; hence, WeCWI encourages meaningful
discussion based on the interactionist theory that involves input,
negotiation, output, and interactional feedback. Rooted in the elearning
interaction-based model, WeCWI promotes online
discussion via synchronous and asynchronous communications,
which allows interactions happened among the learners, instructor,
and digital content. In non-linguistic perspective, WeCWI highlights
on the contribution of reading, discussion, and writing towards
cognitive development. Based on the inquiry models, learners’
critical thinking is fostered during information exploration process
through interaction and questioning. Lastly, to lower writing anxiety,
WeCWI develops the instructional tool with supportive features to
facilitate the writing process. To bring a positive user experience to
the learner, WeCWI aims to create the instructional tool with
different interface designs based on two different types of perceptual
learning style.