Abstract: In this paper we describe the Levenvberg-Marquardt
(LM) algorithm for identification and equalization of CDMA
signals received by an antenna array in communication channels.
The synthesis explains the digital separation and equalization of
signals after propagation through multipath generating intersymbol
interference (ISI). Exploiting discrete data transmitted and three
diversities induced at the reception, the problem can be composed
by the Block Component Decomposition (BCD) of a tensor of
order 3 which is a new tensor decomposition generalizing the
PARAFAC decomposition. We optimize the BCD decomposition by
Levenvberg-Marquardt method gives encouraging results compared to
classical alternating least squares algorithm (ALS). In the equalization
part, we use the Minimum Mean Square Error (MMSE) to perform
the presented method. The simulation results using the LM algorithm
are important.
Abstract: Cost of governance in Nigeria has become a challenge
to development and concern to practitioners and scholars alike in the
field of business and social science research. In the 2010 national
budget of NGN4.6 trillion or USD28.75billion for instance, only a
pantry sum of NGN1.8trillion or USD11.15billion was earmarked for
capital expenditure. Similarly, in 2013, out of a total national budget
of NGN4.92trillion or USD30.75billion, only the sum of
NGN1.50trllion or USD9.38billion was voted for capital expenditure.
Therefore, based on the data sourced from the Nigerian Office of
Statistics, Central bank of Nigeria Statistical Bulletin as well as from
the United Nations Development Programme, this study examined
the causes of high cost of governance in Nigeria. It found out that the
high cost of governance in the country is in the interest of the ruling
class, arising from their unethical behaviour – corrupt practices and
the poor management of public resources. As a result, the study
recommends the need to intensify the war against corruption and
mismanagement of public resources by government officials as
possible solution to overcome the high cost of governance in Nigeria.
This could be achieved by strengthening the constitutional powers of
the various anti-corruption agencies in the area of arrest, investigation
and prosecution of offenders without the interference of the executive
arm of government either at the local, state or federal level.
Abstract: In this study, the performance analyses of the twenty
five Coal-Fired Power Plants (CFPPs) used for electricity generation
are carried out through various Data Envelopment Analysis (DEA)
models. Three efficiency indices are defined and pursued. During the
calculation of the operational performance, energy and non-energy
variables are used as input, and net electricity produced is used as
desired output (Model-1). CO2 emitted to the environment is used as
the undesired output (Model-2) in the computation of the pure
environmental performance while in Model-3 CO2 emissions is
considered as detrimental input in the calculation of operational and
environmental performance. Empirical results show that most of the
plants are operating in increasing returns to scale region and Mettur
plant is efficient one with regards to energy use and environment.
The result also indicates that the undesirable output effect is
insignificant in the research sample. The present study will provide
clues to plant operators towards raising the operational and
environmental performance of CFPPs.
Abstract: Environmental impacts of six 3D printers using
various materials were compared to determine if material choice
drove sustainability, or if other factors such as machine type, machine
size, or machine utilization dominate. Cradle-to-grave life-cycle
assessments were performed, comparing a commercial-scale FDM
machine printing in ABS plastic, a desktop FDM machine printing in
ABS, a desktop FDM machine printing in PET and PLA plastics, a
polyjet machine printing in its proprietary polymer, an SLA machine
printing in its polymer, and an inkjet machine hacked to print in salt
and dextrose. All scenarios were scored using ReCiPe Endpoint H
methodology to combine multiple impact categories, comparing
environmental impacts per part made for several scenarios per
machine. Results showed that most printers’ ecological impacts were
dominated by electricity use, not materials, and the changes in
electricity use due to different plastics was not significant compared
to variation from one machine to another. Variation in machine idle
time determined impacts per part most strongly. However, material
impacts were quite important for the inkjet printer hacked to print in
salt: In its optimal scenario, it had up to 1/38th the impacts coreper
part as the worst-performing machine in the same scenario. If salt
parts were infused with epoxy to make them more physically robust,
then much of this advantage disappeared, and material impacts
actually dominated or equaled electricity use. Future studies should
also measure DMLS and SLS processes / materials.
Abstract: One of the major difficulties introduced with wind
power penetration is the inherent uncertainty in production originating
from uncertain wind conditions. This uncertainty impacts many
different aspects of power system operation, especially the balancing
power requirements. For this reason, in power system development
planing, it is necessary to evaluate the potential uncertainty in future
wind power generation. For this purpose, simulation models are
required, reproducing the performance of wind power forecasts.
This paper presents a wind power forecast error simulation models
which are based on the stochastic process simulation. Proposed
models capture the most important statistical parameters recognized
in wind power forecast error time series. Furthermore, two distinct
models are presented based on data availability. First model uses
wind speed measurements on potential or existing wind power plant
locations, while the seconds model uses statistical distribution of wind
speeds.
Abstract: Measurements and quantitative analysis of kinematic
parameters of human hand movements have an important role in
different areas such as hand function rehabilitation, modeling of
multi-digits robotic hands, and the development of machine-man
interfaces. In this paper the assessment and evaluation of the reachto-
grasp movement by using computerized and robot-assisted method
is described. Experiment involved the measurements of hand
positions of seven healthy subjects during grasping three objects of
different shapes and sizes. Results showed that three dominant phases
of reach-to-grasp movements could be clearly identified.
Abstract: The Simulation based VLSI Implementation of
FELICS (Fast Efficient Lossless Image Compression System)
Algorithm is proposed to provide the lossless image compression and
is implemented in simulation oriented VLSI (Very Large Scale
Integrated). To analysis the performance of Lossless image
compression and to reduce the image without losing image quality
and then implemented in VLSI based FELICS algorithm. In FELICS
algorithm, which consists of simplified adjusted binary code for
Image compression and these compression image is converted in
pixel and then implemented in VLSI domain. This parameter is used
to achieve high processing speed and minimize the area and power.
The simplified adjusted binary code reduces the number of arithmetic
operation and achieved high processing speed. The color difference
preprocessing is also proposed to improve coding efficiency with
simple arithmetic operation. Although VLSI based FELICS
Algorithm provides effective solution for hardware architecture
design for regular pipelining data flow parallelism with four stages.
With two level parallelisms, consecutive pixels can be classified into
even and odd samples and the individual hardware engine is
dedicated for each one. This method can be further enhanced by
multilevel parallelisms.
Abstract: The most important component affecting the
efficiency of photovoltaic power systems are solar panels. In other
words, efficiency of these systems are significantly affected due to
the being low efficiency of solar panel. Thus, solar panels should be
operated under maximum power point conditions through a power
converter. In this study, design of boost converter has been carried
out with maximum power point tracking (MPPT) algorithm which is
incremental conductance (Inc-Cond). By using this algorithm,
importance of power converter in MPPT hardware design, impacts of
MPPT operation have been shown. It is worth noting that initial
operation point is the main criteria for determining the MPPT
performance. In addition, it is shown that if value of load resistance is
lower than critical value, failure operation is realized. For these
analyzes, direct duty control is used for simplifying the control.
Abstract: A feeding experiment was conducted to determine the
optimum dietary protein and lipid levels for juvenile fancy carp. Eight
experimental diets were formulated to contain four protein levels (200,
300, 400 and 500 g kg-1) with two lipid levels (70 and 140 g kg-1).
Triplicate groups of fish (initial weight, 12.1±0.2 g fish-1) were
hand-fed the diets to apparent satiation for 8 weeks. Fish growth
performance, feed utilization and feed intake were significantly
(P0.05). Weight gain and feed efficiency ratio tended to
increase as dietary protein level increased up to 400 and 500 g kg-1,
respectively. Daily feed intake of fish decreased with increasing
dietary protein level and that of fish fed diet contained 500 g kg-1
protein was significantly lower than other fish groups. The protein
efficiency ratio of fish fed 400 and 500 g kg-1 protein was lower than
that of fish fed 200 and 300 g kg-1 protein. Moisture, crude protein and
crude lipid contents of muscle and liver were significantly affected by
dietary protein, but not by dietary lipid level (P>0.05). The increase in
dietary lipid level resulted in an increase in linoleic acid in liver and
muscle paralleled with a decrease in n-3 highly unsaturated fatty acids
content in muscle of fish. In considering these results, it was concluded
that the diet containing 400 g kg-1 protein with 70 g kg-1 lipid level is
optimal for growth and efficient feed utilization of juvenile fancy carp.
Abstract: Nowadays, the successful implementation of ICTs is
vital for almost any kind of organization. Good governance and ICT
management are essential for delivering value, managing
technological risks, managing resources and performance
measurement. In addition, outsourcing is a strategic IT service
solution which complements IT services provided internally in
organizations. This paper proposes the measurement tools of a new
holistic maturity model based on standards ISO/IEC 20000 and
ISO/IEC 38500, and the frameworks and best practices of ITIL and
COBIT, with a specific focus on IT outsourcing. These measurement
tools allow independent validation and practical application in the
field of higher education, using a questionnaire, metrics tables, and
continuous improvement plan tables as part of the measurement
process. Guidelines and standards are proposed in the model for
facilitating adaptation to universities and achieving excellence in the
outsourcing of IT services.
Abstract: Starting in 2020, an EU-wide CO2-limitation of
95 g/km is scheduled for the average of an OEMs passenger car fleet.
Taking that into consideration additional improvement measures of
the Diesel cycle are necessary in order to reduce fuel consumption
and emissions while boosting, or at the least, keeping performance
values at the same time.
The present article deals with the possibilities of an optimized
air/water charge air cooler, also called iCAC (indirect Charge Air
Cooler) for a Diesel passenger car amongst extreme-boundary
conditions. In this context, the precise objective was to show the
impact of improved intercooling with reference to the engine working
process (fuel consumption and NOx-emissions). Several extremeboundaries
- e.g. varying ambient temperatures or mountainous
routes - that will become very important in the near future regarding
RDE (Real Driving emissions) were subject of the investigation.
With the introduction of RDE in 2017 (EU6c measure), the
controversial NEDC (New European Driving Cycle) will belong to
the past and the OEMs will have to avoid harmful emissions in any
conceivable real life situation.
This is certainly going to lead to optimization-measurements at the
powertrain, which again is going to make the implementation of
iCACs, presently solely used for the premium class, more and more
attractive for compact class cars. The investigations showed a benefit
in FC between 1 and 3% for the iCAC in real world conditions.
Abstract: Water spray cooling is a technique typically used in
heat treatment and other metallurgical processes where controlled
temperature regimes are required. Water spray cooling is used in
static (without movement) or dynamic (with movement of the steel
plate) regimes. The static regime is notable for the fixed position of
the hot steel plate and fixed spray nozzle. This regime is typical for
quenching systems focused on heat treatment of the steel plate. The
second application of spray cooling is the dynamic regime. The
dynamic regime is notable for its static section cooling system and
moving steel plate. This regime is used in rolling and finishing mills.
The fixed position of cooling sections with nozzles and the
movement of the steel plate produce nonhomogeneous water
distribution on the steel plate. The length of cooling sections and
placement of water nozzles in combination with the nonhomogeneity
of water distribution lead to discontinued or interrupted cooling
conditions. The impact of static and dynamic regimes on cooling
intensity and the heat transfer coefficient during the cooling process
of steel plates is an important issue.
Heat treatment of steel is accompanied by oxide scale growth. The
oxide scale layers can significantly modify the cooling properties and
intensity during the cooling. The combination of static and dynamic
(section) regimes with the variable thickness of the oxide scale layer
on the steel surface impact the final cooling intensity. The study of
the influence of the oxide scale layers with different cooling regimes
was carried out using experimental measurements and numerical
analysis. The experimental measurements compared both types of
cooling regimes and the cooling of scale-free surfaces and oxidized
surfaces. A numerical analysis was prepared to simulate the cooling
process with different conditions of the section and samples with
different oxide scale layers.
Abstract: Given the importance of ports as links in the global
supply chains and because they are key elements to induce
competitiveness in their hinterlands, the number of studies devoted to
port governance, management and operations has increased in the last
decades. Some of these studies address the port governance model as
an element to improve coordination among the actors of the portlogistics
chain and to generate a better port performance. In this
context, the present study analyzes the governance of Port of Santos
through individual interviews with port managers, based on a
conceptual model that considers the key dimensions associated with
port governance. The results reinforce the usefulness of the applied
model and highlight some existing improvement opportunities in the
port studied.
Abstract: Operations research science (OR) deals with good
success in developing and applying scientific methods for problem
solving and decision-making. However, by using OR techniques, we
can enhance the use of computer decision support systems to achieve
optimal management for institutions. OR applies comprehensive
analysis including all factors that effect on it and builds mathematical
modeling to solve business or organizational problems. In addition, it
improves decision-making and uses available resources efficiently.
The adoption of OR by universities would definitely contributes to
the development and enhancement of the performance of OR
techniques. This paper provides an understanding of the structures,
approaches and models of OR in problem solving and decisionmaking.
Abstract: This paper presents a new structure of microstrip band
pass filter (BPF) based on coupled stepped impedance resonators.
Each filter consists of two coupled stepped impedance resonators
connected to microstrip feed lines. The coupled junction is utilized to
connect the two BPFs to the antenna. This two band pass filters are
designed and simulated to operate for the digital communication
system (DCS) and Industrial Scientific and Medical (ISM) bands at
1.8 GHz and 2.45 GHz respectively. The proposed circuit presents
good performances with an insertion loss lower than 2.3 dB and
isolation between the two channels greater than 21 dB. The prototype
of the optimized diplexer have been investigated numerically by
using ADS Agilent and verified with CST microwave software.
Abstract: In this study the instability problem of a modified
Taylor-Couette flow between two vertical coaxial cylinders of radius
R1, R2 is considered. The modification is based on the wavy shape of
the inner cylinder surface, where inner cylinders with different
surface amplitude and wavelength are used. The study aims to
discover the effect of the inner surface geometry on the instability
phenomenon that undergoes Taylor-Couette flow. The study reveals
that the transition processes depends strongly on the amplitude and
wavelength of the inner cylinder surface and resulting in flow
instabilities that are strongly different from that encountered in the
case of the classical Taylor-Couette flow.
Abstract: Artificial Neural Network (ANN) can be trained using
back propagation (BP). It is the most widely used algorithm for
supervised learning with multi-layered feed-forward networks.
Efficient learning by the BP algorithm is required for many practical
applications. The BP algorithm calculates the weight changes of
artificial neural networks, and a common approach is to use a twoterm
algorithm consisting of a learning rate (LR) and a momentum
factor (MF). The major drawbacks of the two-term BP learning
algorithm are the problems of local minima and slow convergence
speeds, which limit the scope for real-time applications. Recently the
addition of an extra term, called a proportional factor (PF), to the
two-term BP algorithm was proposed. The third increases the speed
of the BP algorithm. However, the PF term also reduces the
convergence of the BP algorithm, and criteria for evaluating
convergence are required to facilitate the application of the three
terms BP algorithm. Although these two seem to be closely related,
as described later, we summarize various improvements to overcome
the drawbacks. Here we compare the different methods of
convergence of the new three-term BP algorithm.
Abstract: This study examines the credibility of the signaling as
explanation for IPO initial underpricing. Findings reveal the initial
underpricing and the long-term underperformance of IPOs in Taiwan.
However, we only find weak support for signaling as explanation of
IPO underpricing.
Abstract: In this study which has been conducted in Akçasu
Forest Range District of Devrek Forest Directorate; 3 methods (weed
control with labourer power, cover removal with Hitachi F20
Excavator, and weed control with agricultural equipment mounted on
a Ferguson 240S agriculture tractor) were utilized in weed control
efforts in regeneration of degraded oriental beech forests have been
compared. In this respect, 3 methods have been compared by
determining certain work hours and standard durations of unit areas
(1 hectare). For this purpose, evaluating the tasks made with human
and machine force from the aspects of duration, productivity and
costs, it has been aimed to determine the most productive method in
accordance with the actual ecological conditions of research field.
Within the scope of the study, the time studies have been conducted
for 3 methods used in weed control efforts. While carrying out those
studies, the performed implementations have been evaluated by
dividing them into business stages. Also, the actual data have been
used while calculating the cost accounts. In those calculations, the
latest formulas and equations which are also used in developed
countries have been utilized. The variance of analysis (ANOVA) was
used in order to determine whether there is any statistically
significant difference among obtained results, and the Duncan test
was used for grouping if there is significant difference. According to
the measurements and findings carried out within the scope of this
study, it has been found during living cover removal efforts in
regeneration efforts in demolished oriental beech forests that the
removal of weed layer in 1 hectare of field has taken 920 hours with
labourer force, 15.1 hours with excavator and 60 hours with an
equipment mounted on a tractor. On the other hand, it has been
determined that the cost of removal of living cover in unit area (1
hectare) was 3220.00 TL for labourer power, 1250 TL for excavator
and 1825 TL for equipment mounted on a tractor.
According to the obtained results, it has been found that the
utilization of excavator in weed control effort in regeneration of
degraded oriental beech regions under actual ecological conditions of
research field has been found to be more productive from both of
aspects of duration and costs. These determinations carried out
should be repeated in weed control efforts in degraded forest fields
with different ecological conditions, it is compulsory for finding the
most efficient weed control method. These findings will light the way
of technical staff of forestry directorate in determination of the most
effective and economic weed control method. Thus, the more actual
data will be used while preparing the weed control budgets, and there
will be significant contributions to national economy. Also the results of this and similar studies are very important for developing the policies for our forestry in short and long term.
Abstract: Liposome plays an important role in medical and
pharmaceutical science as e.g. nano scale drug carriers. Liposomes
are vesicles of varying size consisting of a spherical lipid bilayer and
an aqueous inner compartment. Magnet-driven liposome used for the
targeted delivery of drugs to organs and tissues. These liposome
preparations contain encapsulated drug components and finely
dispersed magnetic particles.
Liposomes are vesicles of varying size consisting of a spherical
lipid bilayer and an aqueous inner compartment that are generated in
vitro. These are useful in terms of biocompatibility, biodegradability,
and low toxicity, and can control biodistribution by changing the size,
lipid composition, and physical characteristics. Furthermore,
liposomes can entrap both hydrophobic and hydrophilic drugs and are
able to continuously release the entrapped substrate, thus being useful
drug carriers. Magnetic liposomes (MLs) are phospholipid vesicles
that encapsulate magneticor paramagnetic nanoparticles. They are
applied as contrast agents for magnetic resonance imaging (MRI).
The biological synthesis of nanoparticles using plant extracts plays
an important role in the field of nanotechnology. Green-synthesized
magnetite nanoparticles-protein hybrid has been produced by treating
Iron (III) / Iron (II) chloride with the leaf extract of Datura inoxia.
The phytochemicals present in the leaf extracts act as a reducing as
well stabilizing agents preventing agglomeration, which include
flavonoids, phenolic compounds, cardiac glycosides, proteins and
sugars.
The magnetite nanoparticles-protein hybrid has been trapped
inside the aqueous core of the liposome prepared by reversed phase
evaporation (REV) method using oleic and linoleic acid which has
been shown to be driven under magnetic field confirming the
formation magnetic liposome (ML). Chemical characterization of
stealth magnetic liposome has been performed by breaking the
liposome and release of magnetic nanoparticles. The presence iron
has been confirmed by colour complex formation with KSCN and
UV-Vis study using spectrophotometer Cary 60, Agilent.
This magnet driven liposome using nanoparticles-protein hybrid
can be a smart vesicles for the targeted drug delivery.