Abstract: In this paper, the design of wide-swing constant transconductance (gm) bias circuit that generates bias voltage for low-noise amplifier (LNA) circuit design by using an off-chip resistor is demonstrated. The overall transconductance (Gm) generated by the constant gm bias circuit is important to maintain the overall gain and noise figure of the LNA circuit. Therefore, investigation is performed to study the variation in Gm with process, temperature and supply voltage (PVT). Temperature and supply voltage are swept from -10 °C to 85 °C and 1.425 V to 1.575 V respectively, while the process conditions are also varied to the extreme and the gm variation is eventually concluded at between -3 % to 7 %. With the slight variation in the gm value, through simulation, at worst condition of state SS, we are able to attain a conversion gain (S21) variation of -3.10 % and a noise figure (NF) variation of 18.71 %. The whole constant gm circuit draws approximately 100 µA from a 1.5V supply and is designed based on 0.13 µm CMOS process.
Abstract: This paper presents the design and implementation of a fully integrated Capacitance-to-Voltage Converter (CVC) as the analog front-end for magnetometer interface IC. The application demands very low power solution operating in the frequency of around 20 KHz. The design adapts low power architecture to create low noise electronic interface for Capacitive Micro-machined Lorentz force magnetometer sensor. Using a 0.18-μm CMOS process, simulation results of this interface IC show that the proposed CVC can provide 33 dB closed loop gain, 20 nV/√Hz input referred noise at 20 KHz, while consuming 65 μA current from 1.8-V supply.
Abstract: Customer audits are generally used to ensure customer
that supplier is continuously able to meet his requirements while
supplying him required products and services. However, customer
audits can be considered as a very useful quality control tool for
suppliers as well. In our paper, we analyzed the process of customer
audits realized in Czech companies from both perspectives: a
supplier´s viewpoint and customer´s viewpoint. At the end, we tried
to emphasize some areas that should not be omitted during the audit
process.
Abstract: In biomedical implant field, a new formula is given
for the study of Radio Frequency power attenuation by simultaneous
effects of side and angular misalignment of the supply/data transfer
coils. A confrontation with the practical measurements done into a
Faraday cage, allowed a checking of the obtained theoretical results.
The DC supply systems without material connection and the data
transmitters used in the case of biomedical implants, can be well
dimensioned by taking into account the possibility of power
attenuation by misalignment of transfer coils
Abstract: Knowledge of food resource of the houbara which an
endangered species would be a important step toward the
preservation of this bird. Adequate study has not been done in this
field and therefore the food sources of the houbara during the
brooding season was studied in the central steppe of Iran. In order to
determine the density of insect in plant communities the pitfall trap
was used , positioned in five linear transects divided between plant
communities and in two repetitions. The results showed that the
among communities there was a significant difference in term of the
number beetles and ants ( p= 0.01, F2, 29= 4.66) collectively. Also
bush steppe habitat had a higher arthropoda density in comparison
with the shrub steppe habitat. Considering that most houbara nests
were found in the bush steppe habitat .It seems this habitat provides
the most available food supply for the houbara chicks.
Abstract: An electric utility-s main concern is to plan, design, operate and maintain its power supply to provide an acceptable level of reliability to its users. This clearly requires that standards of reliability be specified and used in all three sectors of the power system, i.e., generation, transmission and distribution. That is why reliability of a power system is always a major concern to power system planners. This paper presents the reliability analysis of Bangladesh Power System (BPS). Reliability index, loss of load probability (LOLP) of BPS is evaluated using recursive algorithm and considering no de-rated states of generators. BPS has sixty one generators and a total installed capacity of 5275 MW. The maximum demand of BPS is about 5000 MW. The relevant data of the generators and hourly load profiles are collected from the National Load Dispatch Center (NLDC) of Bangladesh and reliability index 'LOLP' is assessed for the period of last ten years.
Abstract: The aim of this paper is to identify an optimum
control strategy of three-phase shunt active filters to minimize the total harmonic distortion factor of the supply current. A classical PIPI cascade control solution of the output current of the active filterand the voltage across the DC capacitor based on Modulus–Optimum
criterion is taken into consideration. The control system operation
has been simulated using Matlab-Simulink environment and the results agree with the theoretical expectation. It is shown that there is
an optimum value of the DC-bus voltage which minimizes the supply current harmonic distortion factor. It corresponds to the equality of the apparent power at the output of the active filter and the apparent power across the capacitor. Finally, predicted results are verified experimentally on a MaxSine active power filter.
Abstract: The protection of groundwater resources is the great
important many semiarid and arid environments. Baghan watershed
is located in the north of Kangan in the Boshehr province in Iran. The
groundwater resources have a vital role in supplying agricultural,
drinking, domestic and industrial water demand in Baghan
watershed. For our investigation into the water quality we collected
30 samples to chemical and physical analysis. The result showed the
marl and evaporation deposits that contain anhydrite and gypsum is
the main source of groundwater pollution, and one part of the
groundwater was polluted by oil and gas industrial. Another part of
the groundwater was contaminated by urban waste water. The
electrical conductivity and captions and anions increased around of
towns and gas refinery. Although the negative impact of untreated
domestic wastewater is relatively low but the results showed strongly
the negative impact of wastewater refinery is very considerable. This
negative impact increased in downstream due to shallow aquifer.
Additionally, the agents that adversely affect the quality of
groundwater come from a variety of sources, including geology,
domestic wastewater and the Jam refinery in Baghan watershed.
Abstract: Collaborative planning, forecasting and
replenishment (CPFR) coordinates the various supply chain
management activities including production and purchase planning,
demand forecasting and inventory replenishment between supply
chain trading partners. This study proposes a systematic way of
analyzing CPFR supporting factors using fuzzy cognitive map
(FCM) approach. FCMs have proven particularly useful for solving
problems in which a number of decision variables and
uncontrollable variables are causally interrelated. Hence the FCMs
of CPFR are created to show the relationships between the factors
that influence on effective implementation of CPFR in the supply
chain.
Abstract: The deficit of power supply in Macedonia is almost 30% or reached up to 3000 GWh in a year. The existing thermal and hydro power plants are not enough to cover the power and energy, so the import increases every year. Therefore, in order to have more domestic energy supply, the new trends in renewable and energy efficiency should be implemented in power sector. The paper gives some perspectives for development of the power system in Macedonia, taking into account the growth of electricity demand and in the same time with implementation of renewable and energy efficiency. The development of power system is made for the period up to 2030 with the period of every 5 years.
Abstract: Particle swarm optimization (PSO) technique is applied to design the water distribution pipeline network. A simulation-optimization model is formulated with the objective of minimizing cost and is applied to a benchmark water distribution system optimization problem. The benchmark problem taken for the application of PSO technique to optimize the pipe size of the water distribution network is New York City water supply system problem. The results from the analysis infer that PSO is a potential alternative optimization technique when compared to other heuristic techniques for optimal sizing of water distribution systems.
Abstract: The objective of this study is to present the test
results of variable air volume (VAV) air conditioning system
optimized by two objective genetic algorithm (GA). The objective
functions are energy savings and thermal comfort. The optimal set
points for fuzzy logic controller (FLC) are the supply air temperature
(Ts), the supply duct static pressure (Ps), the chilled water
temperature (Tw), and zone temperature (Tz) that is taken as the
problem variables. Supply airflow rate and chilled water flow rate are
considered to be the constraints. The optimal set point values are
obtained from GA process and assigned into fuzzy logic controller
(FLC) in order to conserve energy and maintain thermal comfort in
real time VAV air conditioning system. A VAV air conditioning
system with FLC installed in a software laboratory has been taken for
the purpose of energy analysis. The total energy saving obtained in
VAV GA optimization system with FLC compared with constant air
volume (CAV) system is expected to achieve 31.5%. The optimal
duct static pressure obtained through Genetic fuzzy methodology
attributes to better air distribution by delivering the optimal quantity
of supply air to the conditioned space. This combination enhanced
the advantages of uniform air distribution, thermal comfort and
improved energy savings potential.
Abstract: An experiment was performed in the south of
Morocco in order to evaluate the effect of deficit irrigation by treated
wastewater on chickpea production. We applied six irrigation
treatments on a local variety of chickpea by supplying alternatively
50 or 100% of ETm in a completely randomized design.
We found a highly significant difference between treatments in
terms of biomass production. Drought stress during the vegetative
period showed highest yield with 6.5 t/ha which was more than the
yield obtained for the control (4.9 t/ha). The optimal crop stage in
which deficit irrigation can be applied is the vegetative growth stage,
as the crop has a chance to develop its root system, to be able to
cover the plant needs for water and nutrient supply during the rest of
cycle, and non stress conditions during the flowering and seed filling
stages allow the plant to optimize its photosynthesis and carbon
translocation, therefore increase its productivity.
Abstract: In the highly competitive and rapidly changing global
marketplace, independent organizations and enterprises often come
together and form a temporary alignment of virtual enterprise in a
supply chain to better provide products or service. As firms adopt the
systems approach implicit in supply chain management, they must
manage the quality from both internal process control and external
control of supplier quality and customer requirements. How to
incorporate quality management of upstream and downstream supply
chain partners into their own quality management system has recently
received a great deal of attention from both academic and practice.
This paper investigate the collaborative feature and the entities-
relationship in a supply chain, and presents an ontology of
collaborative supply chain from an approach of aligning
service-oriented framework with service-dominant logic. This
perspective facilitates the segregation of material flow management
from manufacturing capability management, which provides a
foundation for the coordination and integration of the business process
to measure, analyze, and continually improve the quality of products,
services, and process. Further, this approach characterizes the different
interests of supply chain partners, providing an innovative approach to
analyze the collaborative features of supply chain. Furthermore, this
ontology is the foundation to develop quality management system
which internalizes the quality management in upstream and
downstream supply chain partners and manages the quality in supply
chain systematically.
Abstract: As is needless to say; a majority of accidents, which occur, are due to drunk driving. As such, there is no effective mechanism to prevent this. Here we have designed an integrated system for the same purpose. Alcohol content in the driver-s body is detected by means of an infrared breath analyzer placed at the steering wheel. An infrared cell directs infrared energy through the sample and any unabsorbed energy at the other side is detected. The higher the concentration of ethanol, the more infrared absorption occurs (in much the same way that a sunglass lens absorbs visible light, alcohol absorbs infrared light). Thus the alcohol level of the driver is continuously monitored and calibrated on a scale. When it exceeds a particular limit the fuel supply is cutoff. If the device is removed also, the fuel supply will be automatically cut off or an alarm is sounded depending upon the requirement. This does not happen abruptly and special indicators are fixed at the back to avoid inconvenience to other drivers using the highway signals. Frame work for integration of sensors and control module in a scalable multi-agent system is provided .A SMS which contains the current GPS location of the vehicle is sent via a GSM module to the police control room to alert the police. The system is foolproof and the driver cannot tamper with it easily. Thus it provides an effective and cost effective solution for the problem of drunk driving in vehicles.
Abstract: In this paper we introduce an ultra low power CMOS
LC oscillator and analyze a method to design a low power low phase
noise complementary CMOS LC oscillator. A 1.8GHz oscillator is
designed based on this analysis. The circuit has power supply equal
to 1.1 V and dissipates 0.17 mW power. The oscillator is also
optimized for low phase noise behavior. The oscillator phase noise is
-126.2 dBc/Hz and -144.4 dBc/Hz at 1 MHz and 8 MHz offset
respectively.
Abstract: The importance of supply chain and logistics
management has been widely recognised. Effective management of
the supply chain can reduce costs and lead times and improve
responsiveness to changing customer demands. This paper proposes a
multi-matrix real-coded Generic Algorithm (MRGA) based
optimisation tool that minimises total costs associated within supply
chain logistics. According to finite capacity constraints of all parties
within the chain, Genetic Algorithm (GA) often produces infeasible
chromosomes during initialisation and evolution processes. In the
proposed algorithm, chromosome initialisation procedure, crossover
and mutation operations that always guarantee feasible solutions
were embedded. The proposed algorithm was tested using three sizes
of benchmarking dataset of logistic chain network, which are typical
of those faced by most global manufacturing companies. A half
fractional factorial design was carried out to investigate the influence
of alternative crossover and mutation operators by varying GA
parameters. The analysis of experimental results suggested that the
quality of solutions obtained is sensitive to the ways in which the
genetic parameters and operators are set.
Abstract: This paper presents a new method for read out of the piezoresistive accelerometer sensors. The circuit works based on Instrumentation amplifier and it is useful for reducing offset In Wheatstone Bridge. The obtained gain is 645 with 1μv/°c Equivalent drift and 1.58mw power consumption. A Schmitt trigger and multiplexer circuit control output node. a high speed counter is designed in this work .the proposed circuit is designed and simulated In 0.18μm CMOS technology with 1.8v power supply.
Abstract: Contact centres have been exemplars of scientific management in the discipline of operations management for more than a decade now. With the movement of industries from a resource based economy to knowledge based economy businesses have started to realize the customer eccentricity being the key to sustainability amidst high velocity of the market. However, as technologies have converged and advanced, so have the contact centres. Contact Centres have redirected the supply chains and the concept of retailing is highly diminished due to over exaggeration of cost reduction strategies. In conditions of high environmental velocity together with services featuring considerable information intensity contact centres will require up to date and enlightened agents to satisfy the demands placed upon them by those requesting their services. In this paper we examine salient factors such as Power Distance, Knowledge structures and the dynamics of job specialisation and enlargement to suggest critical success factors in the domain of contact centres.
Abstract: Development of a Robust Supply Chain for Dynamic
Operating Environment as we move further into the twenty first
century, organisations are under increasing pressure to deliver a high
product variation at a reasonable cost without compromise in quality.
In a number of cases this will take the form of a customised or high
variety low volume manufacturing system that requires prudent
management of resources, among a number of functions, to achieve
competitive advantage. Purchasing and Supply Chain management is
one of such function and due to the substantial interaction with
external elements needs to be strategically managed. This requires a
number of primary and supporting tools that will enable the
appropriate decisions to be made rapidly. This capability is
especially vital in a dynamic environment as it provides a pivotal role
in increasing the profit margin of the product. The management of
this function can be challenging by itself and even more for Small
and Medium Enterprises (SMEs) due to the limited resources and
expertise available at their disposal.
This paper discusses the development of tools and concepts
towards effectively managing the purchasing and supply chain
function. The developed tools and concepts will provide a cost
effective way of managing this function within SMEs. The paper
further shows the use of these tools within Contechs, a manufacturer
of luxury boat interiors, and the associated benefits achieved as a
result of this implementation. Finally a generic framework towards
use in such environments is presented.