Abstract: Addition of milli or micro sized particles to the heat
transfer fluid is one of the many techniques employed for improving
heat transfer rate. Though this looks simple, this method has
practical problems such as high pressure loss, clogging and erosion
of the material of construction. These problems can be overcome by
using nanofluids, which is a dispersion of nanosized particles in a
base fluid. Nanoparticles increase the thermal conductivity of the
base fluid manifold which in turn increases the heat transfer rate.
Nanoparticles also increase the viscosity of the basefluid resulting in
higher pressure drop for the nanofluid compared to the base fluid. So
it is imperative that the Reynolds number (Re) and the volume
fraction have to be optimum for better thermal hydraulic
effectiveness. In this work, the heat transfer enhancement using
aluminium oxide nanofluid using low and high volume fraction
nanofluids in turbulent pipe flow with constant wall temperature has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach. Nanofluid, up till
a volume fraction of 1% is found to be an effective heat transfer
enhancement technique. The Nusselt number (Nu) and friction factor
predictions for the low volume fractions (i.e. 0.02%, 0.1 and 0.5%)
agree very well with the experimental values of Sundar and Sharma
(2010). While, predictions for the high volume fraction nanofluids
(i.e. 1%, 4% and 6%) are found to have reasonable agreement with
both experimental and numerical results available in the literature.
So the computationally inexpensive single phase approach can be
used for heat transfer and pressure drop prediction of new nanofluids.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: In designing of condensers, the prediction of pressure
drop is as important as the prediction of heat transfer coefficient.
Modeling of two phase flow, particularly liquid – vapor flow under
diabatic conditions inside a horizontal tube using CFD analysis is
difficult with the available two phase models in FLUENT due to
continuously changing flow patterns. In the present analysis, CFD
analysis of two phase flow of refrigerants inside a horizontal tube of
inner diameter, 0.0085 m and 1.2 m length is carried out using
homogeneous model under adiabatic conditions. The refrigerants
considered are R22, R134a and R407C. The analysis is performed at
different saturation temperatures and at different flow rates to
evaluate the local frictional pressure drop. Using Homogeneous
model, average properties are obtained for each of the refrigerants
that is considered as single phase pseudo fluid. The so obtained
pressure drop data is compared with the separated flow models
available in literature.
Abstract: The study was carried out to evaluated effect of S-gridling on fruit growth and quality of wax apple. The study was laid in Random completed block design with four replicated. Four treatment were applied as follows: S-girdling, fruit thinning plus bagging with 2,4-D sprayed, fruit thinning plus bagging and the control treatment. 2,4D was sprayed at the small bud and petal fall stage. Girdling was applied three week before flowering. The effect of all treatments on fruit growth was measured weekly. Number of flower, fruit set, fruit drop, fruit crack, and fruit quality were recorded. The result indicated that S-girdling, 2,4D application produced the lowest bud drop, fruit drop compared to untreated control. S-girdling improved faster fruit growth producing the best final fruit length and diameter compared to untreated control. S-girdling also markedly enhanced fruit set, fruit weight, and total soluble solid, reduced fruit crack, titratable acidity. On the other hand, it was noticed that with 2,4-D application also increased the fruit growth rate, improved physiological and biochemical characters of fruit than control treatment. It was concluded that S-girdling was recommended as the industry norm to increase fruit set, fruit quality in wax apple. 2,4D application had a distinctive and significant effect on most of the fruit quality characteristics assessed.
Abstract: This paper addresses one important aspect of
combustion system analysis, the spray evaporation and
dispersion modeling. In this study we assume an empty
cylinder which is as a simulator for a ramjet engine and the
cylinder has been studied by cold flow. Four nozzles have the
duties of injection which are located in the entrance of
cylinder. The air flow comes into the cylinder from one side
and injection operation will be done. By changing injection
velocity and entrance air flow velocity, we have studied
droplet sizing and efficient mass fraction of fuel vapor near
and at the exit area. We named the mass of fuel vapor inside
the flammability limit as the efficient mass fraction. Further,
we decreased the initial temperature of fuel droplets and we
have repeated the investigating again. To fulfill the calculation
we used a modified version of KIVA-3V.
Abstract: RFID (Radio Frequency IDentification) system has
been widely used in our life, such as transport systems, passports,
automotive, animal tracking, human implants, library, and so on.
However, the RFID authentication protocols between RF (Radio
Frequency) tags and the RF readers have been bring about various
privacy problems that anonymity of the tags, tracking, eavesdropping,
and so on. Many researchers have proposed the solution of the
problems. However, they still have the problem, such as location
privacy, mutual authentication. In this paper, we show the problems of
the previous protocols, and then we propose a more secure and
efficient RFID authentication protocol.
Abstract: We have measured the pressure drop and convective
heat transfer coefficient of water – based AL(25nm),AL2O3(30nm)
and CuO(50nm) Nanofluids flowing through a uniform heated
circular tube in the fully developed laminar flow regime. The
experimental results show that the data for Nanofluids friction factor
show a good agreement with analytical prediction from the Darcy's
equation for single-phase flow. After reducing the experimental
results to the form of Reynolds, Rayleigh and Nusselt numbers. The
results show the local Nusselt number and temperature have
distribution with the non-dimensional axial distance from the tube
entry. Study decided that thenNanofluid as Newtonian fluids through
the design of the linear relationship between shear stress and the rate
of stress has been the study of three chains of the Nanofluid with
different concentrations and where the AL, AL2O3 and CuO – water
ranging from (0.25 - 2.5 vol %). In addition to measuring the four
properties of the Nanofluid in practice so as to ensure the validity of
equations of properties developed by the researchers in this area and
these properties is viscosity, specific heat, and density and found that
the difference does not exceed 3.5% for the experimental equations
between them and the practical. The study also demonstrated that the
amount of the increase in heat transfer coefficient for three types of
Nano fluid is AL, AL2O3, and CuO – Water and these ratios are
respectively (45%, 32%, 25%) with insulation and without insulation
(36%, 23%, 19%), and the statement of any of the cases the best
increase in heat transfer has been proven that using insulation is
better than not using it. I have been using three types of Nano
particles and one metallic Nanoparticle and two oxide Nanoparticle
and a statement, whichever gives the best increase in heat transfer.
Abstract: The Mobile Ad-hoc Network (MANET) is a collection of self-configuring and rapidly deployed mobile nodes (routers) without any central infrastructure. Routing is one of the potential issues. Many routing protocols are reported but it is difficult to decide which one is best in all scenarios. In this paper on demand routing protocols DSR and DYMO based on IEEE 802.11 DCF MAC protocol are examined and characteristic summary of these routing protocols is presented. Their performance is analyzed and compared on performance measuring metrics throughput, dropped packets due to non availability of routes, duplicate RREQ generated for route discovery and normalized routing load by varying CBR data traffic load using QualNet 5.0.2 network simulator.
Abstract: Transient shape variation of a rotating liquid dropletis
simulated numerically. The three dimensional Navier-Stokes
equations were solved by using the level set method. The shape
variation from the sphere to the rotating ellipsoid, and to the two-robed
shapeare simulated, and the elongation of the two-robed droplet is
discussed. The two-robed shape after the initial transient is found to be
stable and the elongation is almost the same for the cases with different
initial rotation rate. The relationship between the elongation and the
rotation rate is obtained by averaging the transient shape variation. It is
shown that the elongation of two-robed shape is in good agreement
with the existing experimental data. It is found that the transient
numerical simulation is necessary for analyzing the largely elongated
two-robed shape of rotating droplet.
Abstract: The characteristics of fluid flow and phase separation
in an oil-water separator were numerically analysed as part of the
work presented herein. Simulations were performed for different
velocities and droplet diameters, and the way this parameters can
influence the separator geometry was studied.
The simulations were carried out using the software package
Fluent 6.2, which is designed for numerical simulation of fluid flow
and mass transfer. The model consisted of a cylindrical horizontal
separator. A tetrahedral mesh was employed in the computational
domain. The condition of two-phase flow was simulated with the
two-fluid model, taking into consideration turbulence effects using
the k-ε model.
The results showed that there is a strong dependency of phase
separation on mixture velocity and droplet diameter. An increase in
mixture velocity will bring about a slow down in phase separation
and as a consequence will require a weir of greater height. An
increase in droplet diameter will produce a better phase separation.
The simulations are in agreement with results reported in literature
and show that CFD can be a useful tool in studying a horizontal oilwater
separator.
Abstract: Repeated additions of the unfertilized bacteria led to
increase the activity of Nitrogen-fixing bacteria in the root zone with
drip irrigation system compared to traditional manual vaccination to
increase the proportion of Nitrogen from 29% to 64%, and the
efficiency of adding Nitrogen fertilizer did not exceed 9.5% while
dropped to 4%, due to the amount of fertilizer added was not exceed
20kg N/h, and the second was the existence of a large amount of
available Nitrogen in the soil by fixation, while the efficiency of
irrigation system between 2.08 to 2.26 kg/m3.
Abstract: This paper presents the experimental results of silicone rubber housing material for 24kV lightning arrester under artificial accelerated ageing test based on IEC 61109 specifications. Specimens having inclined and alternated shed made of HTV silicone rubber with ATH content and having leakage distance 625 mm were tested continuously 1000 hrs in artificial salt fog chamber. After 1000 hrs of salt fog ageing test, obviously surface erosion was observed on trunk between the upper large shed and the lower small shed near the energized end. Decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Chemical analysis by ATR-FTIR confirmed the observation results.
Abstract: Two different superhydrophobic surfaces were
elaborated and their oil repellency behavior was evaluated using
several liquid with different surface tension. A silicone rubber/SiO2
nanocomposite coated (A) on aluminum substrate by “spin-coating"
and the sample B was an anodized aluminum surface covered by
Teflon-like coating. A high static contact angle about ∼162° was
measured for two prepared surfaces on which the water droplet rolloff.
Scanning electron microscopy (SEM) showed the presence of
micro/nanostructures for both sample A and B similar to that of lotus
leaf.
However the sample A presented significantly different behaviour
of wettability against the low surface tension liquid. Sample A has
been wetted totally by oil (dodecan) droplet while sample B showed
oleophobic behaviour. Oleophobic property of Teflon like coating
can be contributed to the presence of CF2 and CF3 functional group
which was shown by XPS analysis.
Abstract: In recent years Malaysia has included renewable
energy as an alternative fuel to help in diversifying the country-s
energy reliance on oil, natural gas, coal and hydropower with
biomass and solar energy gaining priority. The scope of this paper is
to look at the designing procedures and analysis of a solar thermal
parabolic trough concentrator by simulation utilizing meteorological
data in several parts of Malaysia. Parameters which include the
aperture area, the diameter of the receiver and the working fluid may
be varied to optimize the design. Aperture area is determined by
considering the width and the length of the concentrator whereas the
geometric concentration ratio (CR) is obtained by considering the
width and diameter of the receiver. Three types of working fluid are
investigated. Theoretically, concentration ratios can be very high in
the range of 10 to 40 000 depending on the optical elements used and
continuous tracking of the sun. However, a thorough analysis is
essential as discussed in this paper where optical precision and
thermal analysis must be carried out to evaluate the performance of
the parabolic trough concentrator as the theoretical CR is not the only
factor that should be considered.
Abstract: Combustion of sprays is of technological importance, but its flame behavior is not fully understood. Furthermore, the multiplicity of dependent variables such as pressure, temperature, equivalence ratio, and droplet sizes complicates the study of spray combustion. Fundamental study on the influence of the presence of liquid droplets has revealed that laminar flames within aerosol mixtures more readily become unstable than for gaseous ones and this increases the practical burning rate. However, fundamental studies on turbulent flames of aerosol mixtures are limited particularly those under near mono-dispersed droplet conditions. In the present work, centrally ignited expanding flames at near atmospheric pressures are employed to quantify the burning rates in gaseous and aerosol flames. Iso-octane-air aerosols are generated by expansion of the gaseous pre-mixture to produce a homogeneously distributed suspension of fuel droplets. The effects of the presence of droplets and turbulence velocity in relation to the burning rates of the flame are also investigated.
Abstract: In this research, heat transfer of a poly Ethylene
fluidized bed reactor without reaction were studied experimentally
and computationally at different superficial gas velocities. A multifluid
Eulerian computational model incorporating the kinetic theory
for solid particles was developed and used to simulate the heat
conducting gas–solid flows in a fluidized bed configuration.
Momentum exchange coefficients were evaluated using the Syamlal–
O-Brien drag functions. Temperature distributions of different phases
in the reactor were also computed. Good agreement was found
between the model predictions and the experimentally obtained data
for the bed expansion ratio as well as the qualitative gas–solid flow
patterns. The simulation and experimental results showed that the gas
temperature decreases as it moves upward in the reactor, while the
solid particle temperature increases. Pressure drop and temperature
distribution predicted by the simulations were in good agreement
with the experimental measurements at superficial gas velocities
higher than the minimum fluidization velocity. Also, the predicted
time-average local voidage profiles were in reasonable agreement
with the experimental results. The study showed that the
computational model was capable of predicting the heat transfer and
the hydrodynamic behavior of gas-solid fluidized bed flows with
reasonable accuracy.
Abstract: Observations show that power plant efficiency
decreases in hot summer days. Water droplet injection in air
condensers is suggested in order to decrease the inlet air temperature.
Nozzle arrangement, injected water flow rate and droplets diameter
effects on evaporation rate and the resulting air temperature are
investigated using numerical simulation. Decreasing the diameter of
injected droplets and increasing the number of injecting nozzles,
decreases the outlet air temperature. Also a more uniform air
temperature can be obtained using more injecting nozzles. Numerical
results are in good agreement with analytical results.
Abstract: This paper presents the experimental results of silicone rubber outdoor polymer insulators in salt fog ageing test based on IEC 61109. Specimens made ofHTV silicone rubber with ATH content having three different configurations, straight shedsalternated sheds, and incline and alternate sheds, were tested continuously 1000 hrs.in artificial salt fog chamber. Contamination level, reduction of hydrophobicity and hardness measurement were used as physical damaged inspection techniques to evaluate degree of surface deterioration. In addition, chemical changing of tested specimen surface was evaluated by ATR-FTIRto confirm physical damaged inspection. After 1000 hrs.of salt fog test, differences in degree of surface deterioration were observed on all tested specimens. Physical damaged inspection and chemical analysis results confirmed the experimental results as well.
Abstract: This paper presents a methodology to harvest the kinetic energy of the raindrops using piezoelectric devices. In the study 1m×1m PVDF (Polyvinylidene fluoride) piezoelectric membrane, which is fixed by the four edges, is considered for the numerical simulation on deformation of the membrane due to the impact of the raindrops. Then according to the drop size of the rain, the simulation is performed classifying the rainfall types into three categories as light stratiform rain, moderate stratiform rain and heavy thundershower. The impact force of the raindrop is dependent on the terminal velocity of the raindrop, which is a function of raindrop diameter. The results were then analyzed to calculate the harvestable energy from the deformation of the piezoelectric membrane.
Abstract: fifteen cultivars of Strawberries (Queen Eliza, Sequia,
Paros, Mcdonance, Selva, Chandler, Mrak, Ten beauty, Aliso, Pajero,
Kordestan, Camarosa, Blackmore, Gaviota and Fresno) were
investigated in 2011, under hydroponic system condition. Yield and
fruit Firmness was determinate. Chemical analyses of soluble solids
content (SSC), titratable acidity (TA), ascorbic acid (AA) and pH
were done. 4 cultivars (Aliso, Selva, Paros and Gaviota) yielded more
than 250 g/plant, while cultivar Black more, Fresno and Kordestan
produced less than 100g/plant. The amounts of fruit firmness
indicated that 'Camarosa' fruit was firmer than others cultivars.
Cultivar 'Fresno' had the highest pH (3.27). Ttitratable acidity varied
from 1.03g/l00g for cultivar 'Sequia' and 'Gaviota' to 1.48g/l00g for
cultivar 'Chandler'. Fresno, Kordestan, Aliso and Chandler showed
the highest soluble solid concentration. Ascorbic acid averaged for
most cultivars between 30.26 and 79.73 mg/100gf.w. Present results
showed that different cultivars of strawberry contain highly variable
in fruit quality.