Abstract: To evaluate genetic variation of wheat (Triticum
aestivum) affected by heat and drought stress on eight Australian
wheat genotypes that are parents of Doubled Haploid (HD) mapping
populations at the vegetative stage, the water stress experiment was
conducted at 65% field capacity in growth room. Heat stress
experiment was conducted in the research field under irrigation over
summer. Result show that water stress decreased dry shoot weight
and RWC but increased osmolarity and means of Fv/Fm values in all
varieties except for Krichauff. Krichauff and Kukri had the
maximum RWC under drought stress. Trident variety was shown
maximum WUE, osmolarity (610 mM/Kg), dry mater, quantum yield
and Fv/Fm 0.815 under water stress condition. However, the
recovery of quantum yield was apparent between 4 to 7 days after
stress in all varieties. Nevertheless, increase in water stress after that
lead to strong decrease in quantum yield. There was a genetic
variation for leaf pigments content among varieties under heat stress.
Heat stress decreased significantly the total chlorophyll content that
measured by SPAD. Krichauff had maximum value of Anthocyanin
content (2.978 A/g FW), chlorophyll a+b (2.001 mg/g FW) and
chlorophyll a (1.502 mg/g FW). Maximum value of chlorophyll b
(0.515 mg/g FW) and Carotenoids (0.234 mg/g FW) content
belonged to Kukri. The quantum yield of all varieties decreased
significantly, when the weather temperature increased from 28 ÔùªC to
36 ÔùªC during the 6 days. However, the recovery of quantum yield
was apparent after 8th day in all varieties. The maximum decrease
and recovery in quantum yield was observed in Krichauff. Drought
and heat tolerant and moderately tolerant wheat genotypes were
included Trident, Krichauff, Kukri and RAC875. Molineux, Berkut
and Excalibur were clustered into most sensitive and moderately
sensitive genotypes. Finally, the results show that there was a
significantly genetic variation among the eight varieties that were
studied under heat and water stress.
Abstract: Wireless ad hoc nodes are freely and dynamically
self-organize in communicating with others. Each node can act as
host or router. However it actually depends on the capability of
nodes in terms of its current power level, signal strength, number
of hops, routing protocol, interference and others. In this research,
a study was conducted to observe the effect of hops count over
different network topologies that contribute to TCP Congestion
Control performance degradation. To achieve this objective, a
simulation using NS-2 with different topologies have been
evaluated. The comparative analysis has been discussed based on
standard observation metrics: throughput, delay and packet loss
ratio. As a result, there is a relationship between types of topology
and hops counts towards the performance of ad hoc network. In
future, the extension study will be carried out to investigate the
effect of different error rate and background traffic over same
topologies.
Abstract: Connected dominating set (CDS) problem in unit disk
graph has signi£cant impact on an ef£cient design of routing protocols
in wireless sensor networks, where the searching space for a
route is reduced to nodes in the set. A set is dominating if all the
nodes in the system are either in the set or neighbors of nodes in the
set. In this paper, a simple and ef£cient heuristic method is proposed
for £nding a minimum connected dominating set (MCDS) in ad hoc
wireless networks based on the new parameter support of vertices.
With this parameter the proposed heuristic approach effectively
£nds the MCDS of a graph. Extensive computational experiments
show that the proposed approach outperforms the recently proposed
heuristics found in the literature for the MCD
Abstract: Exploding concentrated underwater charges to
damage underwater structures such as ship hulls is a part of naval
warfare strategies. Adding small amounts of foreign particles (like
clay or silica) of nanosize significantly improves the engineering
properties of the polymers. In the present work the clay in terms 1, 2
and 3 percent by weight was surface treated with a suitable silane
agent. The hybrid nanocomposite was prepared by the hand lay-up
technique. Mathematical regression models have been employed for
theoretical prediction. This will result in considerable savings in terms of project time, effort and cost.
Abstract: When studying electronics, hands-on experience is considered to be very valuable for a better understanding of the concepts of electricity and electronics. Students lacking sufficient time in the lab are often put at disadvantage. A way to overcome this, is by using interactive multimedia in a virtual environment. Instead of proposing another new ad-hoc simulator for e-learning, we propose in this paper an e-learning platform integrating the SPICE simulator as a web service. This enables to make use of all the functions of the de-facto standard simulator SPICE inelectronics when developing new simulations.
Abstract: Through the course of this paper we define Business Case Management and its characteristics, and highlight its link to knowledge workers. Business Case Management combines knowledge and process effectively, supporting the ad hoc and unpredictable nature of cases, and coordinate a range of other technologies to appropriately support knowledge-intensive processes. We emphasize the growing importance of knowledge workers and the current poor support for knowledge work automation. We also discuss the challenges in supporting this kind of knowledge work and propose a novel approach to overcome these challenges.
Abstract: In this paper, a Cooperative Multi-robot for Carrying
Targets (CMCT) algorithm is proposed. The multi-robot team
consists of three robots, one is a supervisor and the others are
workers for carrying boxes in a store of 100×100 m2. Each robot has
a self recharging mechanism. The CMCT minimizes robot-s worked
time for carrying many boxes during day by working in parallel. That
is, the supervisor detects the required variables in the same time
another robots work with previous variables. It works with
straightforward mechanical models by using simple cosine laws. It
detects the robot-s shortest path for reaching the target position
avoiding obstacles by using a proposed CMCT path planning
(CMCT-PP) algorithm. It prevents the collision between robots
during moving. The robots interact in an ad hoc wireless network.
Simulation results show that the proposed system that consists of
CMCT algorithm and its accomplished CMCT-PP algorithm
achieves a high improvement in time and distance while performing
the required tasks over the already existed algorithms.
Abstract: Data mining uses a variety of techniques each of which is useful for some particular task. It is important to have a deep understanding of each technique and be able to perform sophisticated analysis. In this article we describe a tool built to simulate a variation of the Kohonen network to perform unsupervised clustering and support the entire data mining process up to results visualization. A graphical representation helps the user to find out a strategy to optmize classification by adding, moving or delete a neuron in order to change the number of classes. The tool is also able to automatically suggest a strategy for number of classes optimization.The tool is used to classify macroeconomic data that report the most developed countries? import and export. It is possible to classify the countries based on their economic behaviour and use an ad hoc tool to characterize the commercial behaviour of a country in a selected class from the analysis of positive and negative features that contribute to classes formation.
Abstract: Heat-inducible gene expression vectors are useful for hyperthermia-induced cancer gene therapy, because the combination
of hyperthermia and gene therapy can considerably improve the therapeutic effects. In the present study, we developed an enhanced
heat-inducible transgene expression system in which a heat-shock
protein (HSP) promoter and tetracycline-responsive transactivator
were combined. When the transactivator plasmid containing the
tetracycline-responsive transactivator gene was co-transfected with
the reporter gene expression plasmid, a high level of heat-induced gene expression was observed compared with that using the HSP
promoter without the transactivator. In vitro evaluation of the
therapeutic effect using HeLa cells showed that heat-induced therapeutic gene expression caused cell death in a high percentage of
these cells, indicating that this strategy is promising for cancer gene therapy.
Abstract: Due to the complex network architecture, the mobile
adhoc network-s multihop feature gives additional problems to the
users. When the traffic load at each node gets increased, the
additional contention due its traffic pattern might cause the nodes
which are close to destination to starve the nodes more away from the
destination and also the capacity of network is unable to satisfy the
total user-s demand which results in an unfairness problem. In this
paper, we propose to create an algorithm to compute the optimal
MAC-layer bandwidth assigned to each flow in the network. The
bottleneck links contention area determines the fair time share which
is necessary to calculate the maximum allowed transmission rate used
by each flow. To completely utilize the network resources, we
compute two optimal rates namely, the maximum fair share and
minimum fair share. We use the maximum fair share achieved in
order to limit the input rate of those flows which crosses the
bottleneck links contention area when the flows that are not allocated
to the optimal transmission rate and calculate the following highest
fair share. Through simulation results, we show that the proposed
protocol achieves improved fair share and throughput with reduced
delay.
Abstract: As originally designed for wired networks, TCP (transmission control protocol) congestion control mechanism is triggered into action when packet loss is detected. This implicit assumption for packet loss mostly due to network congestion does not work well in Mobile Ad Hoc Network, where there is a comparatively high likelihood of packet loss due to channel errors and node mobility etc. Such non-congestion packet loss, when dealt with by congestion control mechanism, causes poor TCP performance in MANET. In this study, we continue to investigate the impact of the interaction between transport protocols and on-demand routing protocols on the performance and stability of 802.11 multihop networks. We evaluate the important wireless networking events caused routing change, and propose a cross layer method to delay the unnecessary routing changes, only need to add a sensitivity parameter α , which represents the on-demand routing-s reaction to link failure of MAC layer. Our proposal is applicable to the plain 802.11 networking environment, the simulation results that this method can remarkably improve the stability and performance of TCP without any modification on TCP and MAC protocol.
Abstract: The Eulerian numerical method is proposed to analyze
the explosion in tunnel. Based on this method, an original software
M-MMIC2D is developed by Cµ program language. With this
software, the explosion problem in the tunnel with three
expansion-chambers is numerically simulated, and the results are
found to be in full agreement with the observed experimental data.
Abstract: Numerical studies have been carried out using a
validated two-dimensional RNG k-epsilon turbulence model for the
design optimization of a thrust vector control system using shock
induced supersonic secondary jet. Parametric analytical studies have
been carried out with various secondary jets at different divergent
locations, jet interaction angles, jet pressures. The results from the
parametric studies of the case on hand reveal that the primary nozzle
with a small divergence angle, downstream injections with a distance
of 2.5 times the primary nozzle throat diameter from the primary
nozzle throat location warrant higher efficiency over a certain range
of jet pressures and jet angles. We observed that the supersonic
secondary jet opposing the core flow with jets interaction angle of
40o to the axis far downstream of the nozzle throat facilitates better
thrust vectoring than the secondary jet with same direction as that of
core flow with various interaction angles. We concluded that fixing
of the supersonic secondary jet nozzle pointing towards the throat
direction with suitable angle at a distance 2 to 4 times of the primary
nozzle throat diameter, as the case may be, from the primary nozzle
throat location could facilitate better thrust vectoring for the
supersonic aerospace vehicles.
Abstract: Mobile Ad hoc networks (MANETs) are collections
of wireless mobile nodes dynamically reconfiguring and collectively
forming a temporary network. These types of networks assume
existence of no fixed infrastructure and are often useful in battle-field
tactical operations or emergency search-and-rescue type of
operations where fixed infrastructure is neither feasible nor practical.
They also find use in ad hoc conferences, campus networks and
commercial recreational applications carrying multimedia traffic. All
of the above applications of MANETs require guaranteed levels of
performance as experienced by the end-user. This paper focuses on
key challenges in provisioning predetermined levels of such Quality
of Service (QoS). It also identifies functional areas where QoS
models are currently defined and used. Evolving functional areas
where performance and QoS provisioning may be applied are also
identified and some suggestions are provided for further research in
this area. Although each of the above functional areas have been
discussed separately in recent research studies, since these QoS
functional areas are highly correlated and interdependent, a
comprehensive and comparative analysis of these areas and their
interrelationships is desired. In this paper we have attempted to
provide such an overview.
Abstract: Ad hoc networks are characterized by multi-hop
wireless connectivity and frequently changing network topology.
Forming security association among a group of nodes in ad-hoc
networks is more challenging than in conventional networks due to the
lack of central authority, i.e. fixed infrastructure. With that view in
mind, group key management plays an important building block of
any secure group communication. The main contribution of this paper
is a low complexity key management scheme that is suitable for fully
self-organized ad-hoc networks. The protocol is also password
authenticated, making it resilient against active attacks. Unlike other
existing key agreement protocols, ours make no assumption about the
structure of the underlying wireless network, making it suitable for
“truly ad-hoc" networks. Finally, we will analyze our protocol to show
the computation and communication burden on individual nodes for
key establishment.
Abstract: The decisions made by admission control algorithms are
based on the availability of network resources viz. bandwidth, energy,
memory buffers, etc., without degrading the Quality-of-Service (QoS)
requirement of applications that are admitted. In this paper, we
present an energy-aware admission control (EAAC) scheme which
provides admission control for flows in an ad hoc network based
on the knowledge of the present and future residual energy of the
intermediate nodes along the routing path. The aim of EAAC is to
quantify the energy that the new flow will consume so that it can
be decided whether the future residual energy of the nodes along
the routing path can satisfy the energy requirement. In other words,
this energy-aware routing admits a new flow iff any node in the
routing path does not run out of its energy during the transmission
of packets. The future residual energy of a node is predicted using
the Multi-layer Neural Network (MNN) model. Simulation results
shows that the proposed scheme increases the network lifetime. Also
the performance of the MNN model is presented.
Abstract: In this paper parametric analytical studies have been carried out to examine the intrinsic flow physics pertaining to the liftoff time of solid propellant rockets. Idealized inert simulators of solid rockets are selected for numerical studies to examining the preignition chamber dynamics. Detailed diagnostic investigations have been carried out using an unsteady two-dimensional k-omega turbulence model. We conjectured from the numerical results that the altered variations of the igniter jet impingement angle, turbulence level, time and location of the first ignition, flame spread characteristics, the overall chamber dynamics including the boundary layer growth history are having bearing on the time for nozzle flow chocking for establishing the required thrust for the rocket liftoff. We concluded that the altered flow choking time of strap-on motors with the pre-determined identical ignition time at the lift off phase will lead to the malfunctioning of the rocket. We also concluded that, in the light of the space debris, an error in predicting the liftoff time can lead to an unfavorable launch window amounts the satellite injection errors and/or the mission failures.
Abstract: The main aim of the presented experiments is to
improve behaviour of sandwich structures under dynamic loading,
such as crash or explosion. Several cellular materials are widely used
as core of the sandwich structures and their properties influence
the response of the entire element under impact load. To optimize
their performance requires the characterisation of the core material
behaviour at high strain rates and identification of the underlying
mechanism. This work presents the study of high strain-rate
characteristics of a specific porous lightweight blast energy absorbing
foam using a Split Hopkinson Pressure Bar (SHPB) technique
adapted to perform tests on low strength materials. Two different
velocities, 15 and 30 m.s-1 were used to determine the strain
sensitivity of the material. Foams were designed using two types of
porous lightweight spherical raw materials with diameters of 30-
100 *m, combined with polymer matrix. Cylindrical specimens with
diameter of 15 mm and length of 7 mm were prepared and loaded
using a Split Hopkinson Pressure Bar apparatus to assess the relation
between the composition of the material and its shock wave
attenuation capacity.
Abstract: Mobile devices, which are progressively surrounded
in our everyday life, have created a new paradigm where they
interconnect, interact and collaborate with each other. This network
can be used for flexible and secure coordinated sharing. On the other
hand Grid computing provides dependable, consistent, pervasive, and
inexpensive access to high-end computational capabilities. In this
paper, efforts are made to map the concepts of Grid on Ad-Hoc
networks because both exhibit similar kind of characteristics like
Scalability, Dynamism and Heterogeneity. In this context we
propose “Mobile Ad-Hoc Services Grid – MASGRID".
Abstract: In areas of low to moderate seismicity many building contents and equipment are not positively fixed to the floor or tied to adjacent walls. Under seismic induced horizontal vibration, such contents and equipment can suffer from damage by either overturning or impact associated with rocking. This paper focuses on the estimation of shock on typical contents and equipment due to rocking. A simplified analytical model is outlined that can be used to estimate the maximum acceleration on a rocking object given its basic geometric and mechanical properties. The developed model was validated against experimental results. The experimental results revealed that the maximum shock acceleration can be underestimated if the static stiffness of the materials at the interface between the rocking object and floor is used rather than the dynamic stiffness. Excellent agreement between the model and experimental results was found when the dynamic stiffness for the interface material was used, which was found to be generally much higher than corresponding static stiffness under different investigated boundary conditions of the cushion. The proposed model can be a beneficial tool in performing a rapid assessment of shock sensitive components considered for possible seismic rectification.