Abstract: A gold coated copper rotating electrode was used to
eliminate surface oxidation effect. This study examined the effect of
electrode rotation on the ozone generation process and showed that an
ozonizer with an electrode rotating system might be a possible way to
increase ozone-synthesis efficiency. Two new phenomena appeared
during experiments with the rotating electrode. First was that ozone
concentration increased to about two times higher than that of the case
with no rotation. Second, input power and discharge area were found
to increase with the rotation speed. Both ozone concentration and
ozone production efficiency improved in the case of rotating electrode
compared to the case with a non-rotating electrode. One possible
reason for this was the increase in discharge length of
micro-discharges during electrode rotation. The rotating electrode
decreased onset voltage, while reactor capacitance increased with
rotation. Use of a rotating-type electrode allowed earlier observation
of the ozone zero phenomena compared with a non-rotating electrode
because, during rotation, the entire electrode surface was functional,
allowing nitrogen on the electrode surface to be evenly consumed.
Nitrogen demand increased with increasing rotation s
Abstract: Hydrogen is an important chemical in many industries
and it is expected to become one of the major fuels for energy
generation in the future. Unfortunately, hydrogen does not exist in its
elemental form in nature and therefore has to be produced from
hydrocarbons, hydrogen-containing compounds or water.
Above its critical point (374.8oC and 22.1MPa), water has lower
density and viscosity, and a higher heat capacity than those of
ambient water. Mass transfer in supercritical water (SCW) is
enhanced due to its increased diffusivity and transport ability. The
reduced dielectric constant makes supercritical water a better solvent
for organic compounds and gases. Hence, due to the aforementioned
desirable properties, there is a growing interest toward studies
regarding the gasification of organic matter containing biomass or
model biomass solutions in supercritical water.
In this study, hydrogen and biofuel production by the catalytic
gasification of 2-Propanol in supercritical conditions of water was
investigated. Pt/Al2O3and Ni/Al2O3were the catalysts used in the
gasification reactions. All of the experiments were performed under a
constant pressure of 25MPa. The effects of five reaction temperatures
(400, 450, 500, 550 and 600°C) and five reaction times (10, 15, 20,
25 and 30 s) on the gasification yield and flammable component
content were investigated.
Abstract: Collaborative working environments for distance
education can be considered as a more generic form of contemporary
remote labs. At present, the majority of existing real laboratories are
not constructed to allow the involved participants to collaborate in
real time. To make this revolutionary learning environment possible
we must allow the different users to carry out an experiment
simultaneously. In recent times, multi-user environments are
successfully applied in many applications such as air traffic control
systems, team-oriented military systems, chat-text tools, multi-player
games etc. Thus, understanding the ideas and techniques behind these
systems could be of great importance in the contribution of ideas to
our e-learning environment for collaborative working. In this
investigation, collaborative working environments from theoretical
and practical perspectives are considered in order to build an
effective collaborative real laboratory, which allows two students or
more to conduct remote experiments at the same time as a team. In
order to achieve this goal, we have implemented distributed system
architecture, enabling students to obtain an automated help by either
a human tutor or a rule-based e-tutor.
Abstract: As the enormous amount of on-line text grows on the
World-Wide Web, the development of methods for automatically
summarizing this text becomes more important. The primary goal of
this research is to create an efficient tool that is able to summarize
large documents automatically. We propose an Evolving
connectionist System that is adaptive, incremental learning and
knowledge representation system that evolves its structure and
functionality. In this paper, we propose a novel approach for Part of
Speech disambiguation using a recurrent neural network, a paradigm
capable of dealing with sequential data. We observed that
connectionist approach to text summarization has a natural way of
learning grammatical structures through experience. Experimental
results show that our approach achieves acceptable performance.
Abstract: The weight constrained shortest path problem
(WCSPP) is one of most several known basic problems in
combinatorial optimization. Because of its importance in many areas
of applications such as computer science, engineering and operations
research, many researchers have extensively studied the WCSPP.
This paper mainly concentrates on the reduction of total search space
for finding WCSP using some existing Genetic Algorithm (GA). For
this purpose, some controlled schemes of genetic operators are
adopted on list chromosome representation. This approach gives a
near optimum solution with smaller elapsed generation than classical
GA technique. From further analysis on the matter, a new
generalized schema theorem is also developed from the philosophy
of Holland-s theorem.
Abstract: Tofurther advance research on immune-related genes
from T. molitor, we constructed acDNA library and analyzed
expressed sequence taq (EST) sequences from 1,056 clones. After
removing vector sequence and quality checkingthrough thePhred
program (trim_alt 0.05 (P-score>20), 1039 sequences were generated.
The average length of insert was 792 bp. In addition, we identified 162
clusters, 167 contigs and 391 contigs after clustering and assembling
process using a TGICL package. EST sequences were searchedagainst
NCBI nr database by local BLAST (blastx, E
Abstract: The use of machine vision to inspect the outcome of
surgical tasks is investigated, with the aim of incorporating this
approach in robotic surgery systems. Machine vision is a non-contact
form of inspection i.e. no part of the vision system is in direct contact
with the patient, and is therefore well suited for surgery where
sterility is an important consideration,. As a proof-of-concept, three
primary surgical tasks for a common neurosurgical procedure were
inspected using machine vision. Experiments were performed on
cadaveric pig heads to simulate the two possible outcomes i.e.
satisfactory or unsatisfactory, for tasks involved in making a burr
hole, namely incision, retraction, and drilling. We identify low level
image features to distinguish the two outcomes, as well as report on
results that validate our proposed approach. The potential of using
machine vision in a surgical environment, and the challenges that
must be addressed, are identified and discussed.
Abstract: Business process management (BPM) has become
widely accepted within business community as a means for
improving business performance. However, it is of the highest
importance to incorporate BPM as part of the curriculum at the
university level education in order to achieve the appropriate
acceptance of the method. Goal of the paper is to determine the
current state of education in business process management (BPM) at
the Croatian universities and abroad. It investigates the applied forms
of instruction and teaching methods and gives several proposals for
BPM courses improvement. Since majority of undergraduate and
postgraduate students have limited understanding of business
processes and lack of any practical experience, there is a need for
introducing new teaching approaches. Therefore, we offer some
suggestions for further improvement, among which the introduction
of simulation games environment in BPM education is strongly
recommended.
Abstract: Prestressing in structure increases ratio of load-bearing capacity to weight. Suspendomes are single-layer braced domes reinforced with cable and strut. Prestressing of cables alter value and distribution of stress in structure. In this study two configuration, diamatic and lamella domes is selected. Investigated domes have span of 100m with rise-to-span ratios of 0.1, 0.2, and 0.3. Single layer domes loaded under service load combinations according to ISO code. After geometric nonlinear analysis, models are designed with tubular and I-shaped sections then reinforced with cable and strut and converted to suspendomes. Displacements and stresses of some groups of nodes and elements in all of single-layer domes and suspendomes for three load combinations, symmetric snow, asymmetric snow and wind are compared. Variation due to suspending system is investigated. Suspendomes are redesigned and minimum possible weight after addition of cable and strut is obtained.
Abstract: From an economic standpoint the current and future
road traffic situation in urban areas is a cost factor. Traffic jams and
congestion prolong journey times and tie up resources in trucks and
personnel. Many discussions about imposing charges or tolls for
cities in Europe in order to reduce traffic congestion are currently in
progress. Both of these effects lead – directly or indirectly - to
additional costs for the urban distribution systems in retail
companies. One approach towards improving the efficiency of retail
distribution systems, and thus towards avoiding negative
environmental factors in urban areas, is horizontal collaboration for
deliveries to retail outlets – Urban Retail Logistics. This paper
presents a classification system to help reveal where cooperation
between retail companies is possible and makes sense for deliveries
to retail outlets in urban areas.
Abstract: Arguments on a popular microblogging site were analysed by means of a methodological approach to business rhetoric focusing on the logos communication technique. The focus of the analysis was the 100 day countdown to the 2011 Rugby World Cup as advanced by the organisers. Big sporting events provide an attractive medium for sport event marketers in that they have become important strategic communication tools directed at sport consumers. Sport event marketing is understood in the sense of using a microblogging site as a communication tool whose purpose it is to disseminate a company-s marketing messages by involving the target audience in experiential activities. Sport creates a universal language in that it excites and increases the spread of information by word of mouth and other means. The findings highlight the limitations of a microblogging site in terms of marketing messages which can assist in better practices. This study can also serve as a heuristic tool for other researchers analysing sports marketing messages in social network environments.
Abstract: This paper presents a new classification algorithm using colour and texture for obstacle detection. Colour information is computationally cheap to learn and process. However in many cases, colour alone does not provide enough information for classification. Texture information can improve classification performance but usually comes at an expensive cost. Our algorithm uses both colour and texture features but texture is only needed when colour is unreliable. During the training stage, texture features are learned specifically to improve the performance of a colour classifier. The algorithm learns a set of simple texture features and only the most effective features are used in the classification stage. Therefore our algorithm has a very good classification rate while is still fast enough to run on a limited computer platform. The proposed algorithm was tested with a challenging outdoor image set. Test result shows the algorithm achieves a much better trade-off between classification performance and efficiency than a typical colour classifier.
Abstract: Cellular networks provide voice and data services to the users with mobility. To deliver services to the mobile users, the cellular network is capable of tracking the locations of the users, and allowing user movement during the conversations. These capabilities are achieved by the location management. Location management in mobile communication systems is concerned with those network functions necessary to allow the users to be reached wherever they are in the network coverage area. In a cellular network, a service coverage area is divided into smaller areas of hexagonal shape, referred to as cells. The cellular concept was introduced to reuse the radio frequency. Continued expansion of cellular networks, coupled with an increasingly restricted mobile spectrum, has established the reduction of communication overhead as a highly important issue. Much of this traffic is used in determining the precise location of individual users when relaying calls, with the field of location management aiming to reduce this overhead through prediction of user location. This paper describes and compares various location management schemes in the cellular networks.
Abstract: Recent progress in calculation of the one-loop selfenergy
of the electron bound in the Coulomb field is summarized.
The relativistic multipole expansion is introduced. This expansion
is based on a single assumption: except for the part of the time
component of the electron four-momentum corresponding to the
electron rest mass, the exchange of four-momentum between the
virtual electron and photon can be treated perturbatively. For non Sstates
and normalized difference n3En −E1 of the S-states this
itself yields very accurate results after taking the method to the third
order. For the ground state the perturbation treatment of the electron
virtual states with very high three-momentum is to be avoided. For
these states one can always rearrange the pertinent expression in such
a way that free-particle approximation is allowed. Combination of
the relativistic multipole expansion and free-particle approximation
yields very accurate result after taking the method to the ninth order.
These results are in very good agreement with the previous results
obtained by the partial wave expansion and definitely exclude the
possibility that the uncertainity in determination of the proton radius
comes from the uncertainity in the calculation of the one-loop selfenergy.
Abstract: The proper assessment of interaxial distance and
convergence control are important factors in stereoscopic imaging
technology to make an efficient 3D image. To control interaxial
distance and convergence for efficient 3D shooting, horizontal 3D
camera rig is designed using some hardware components like 'LM
Guide', 'Goniometer' and 'Rotation Stage'. The horizontal 3D camera
rig system can be properly aligned by moving the two cameras
horizontally in same or opposite directions, by adjusting the camera
angle and finally considering horizontal swing as well as vertical
swing. In this paper, the relationship between interaxial distance and
convergence angle control are discussed and intensive experiments are
performed in order to demonstrate an easy and effective 3D shooting.
Abstract: The design of a complete expansion that allows for
compact representation of certain relevant classes of signals is a
central problem in signal processing applications. Achieving such a
representation means knowing the signal features for the purpose of
denoising, classification, interpolation and forecasting. Multilayer
Neural Networks are relatively a new class of techniques that are
mathematically proven to approximate any continuous function
arbitrarily well. Radial Basis Function Networks, which make use of
Gaussian activation function, are also shown to be a universal
approximator. In this age of ever-increasing digitization in the
storage, processing, analysis and communication of information,
there are numerous examples of applications where one needs to
construct a continuously defined function or numerical algorithm to
approximate, represent and reconstruct the given discrete data of a
signal. Many a times one wishes to manipulate the data in a way that
requires information not included explicitly in the data, which is
done through interpolation and/or extrapolation.
Tidal data are a very perfect example of time series and many
statistical techniques have been applied for tidal data analysis and
representation. ANN is recent addition to such techniques. In the
present paper we describe the time series representation capabilities
of a special type of ANN- Radial Basis Function networks and
present the results of tidal data representation using RBF. Tidal data
analysis & representation is one of the important requirements in
marine science for forecasting.
Abstract: Users of computer systems may often require the
private transfer of messages/communications between parties across
a network. Information warfare and the protection and dominance of
information in the military context is a prime example of an
application area in which the confidentiality of data needs to be
maintained. The safe transportation of critical data is therefore often
a vital requirement for many private communications. However,
unwanted interception/sniffing of communications is also a
possibility. An elementary stealthy transfer scheme is therefore
proposed by the authors. This scheme makes use of encoding,
splitting of a message and the use of a hashing algorithm to verify the
correctness of the reconstructed message. For this proof-of-concept
purpose, the authors have experimented with the random sending of
encoded parts of a message and the construction thereof to
demonstrate how data can stealthily be transferred across a network
so as to prevent the obvious retrieval of data.
Abstract: Multilobe bearings are found to be more stable than circular bearings. A three lobe bearing also possesses good stability characteristics. Sometimes the line of action of the load does not pass through the axis of a bearing and is shifted on either side by a few degrees. Load orientation is one of the factors that affect the stability of a three lobe bearing. The effect of load orientation on the stability of a three-lobe has been discussed in this paper. The results show that stability of a three-lobe bearing supporting either rigid or flexible rotor is increased for the positive values of load orientation i.e. when the load line is shifted in the opposite direction of rotation.
Abstract: This work deals with the initial applications and formulation of an anisotropic plastic-damage constitutive model proposed for non-linear analysis of reinforced concrete structures submitted to a loading with change of the sign. The original constitutive model is based on the fundamental hypothesis of energy equivalence between real and continuous medium following the concepts of the Continuum Damage Mechanics. The concrete is assumed as an initial elastic isotropic medium presenting anisotropy, permanent strains and bimodularity (distinct elastic responses whether traction or compression stress states prevail) induced by damage evolution. In order to take into account the bimodularity, two damage tensors governing the rigidity in tension or compression regimes are introduced. Then, some conditions are introduced in the original version of the model in order to simulate the damage unilateral effect. The three-dimensional version of the proposed model is analyzed in order to validate its formulation when compared to micromechanical theory. The one-dimensional version of the model is applied in the analyses of a reinforced concrete beam submitted to a loading with change of the sign. Despite the parametric identification problems, the initial applications show the good performance of the model.
Abstract: This article is investigating Boria which is a kind of common performance in Malaysia. Boria has been known as Boria and Borea and both are correct, but Boria is more common. Boria is a folk performance unique to Penang. This theatre style reached Penang in the mid-19th century and is believed to be derived from the Shia Islamic Passion play performed during the Muslim month of Muharram to commemorate the martyrs of Kerbela. These days in Malaysia (especially Penang) Boria mentions to a choral street performance performed annually by a number of groups composed mostly of Sunni Malaysian. Boria are performed for entertainment and often include an annual singing competition. The size, membership, themes and movements of each Boria troupe may vary from year to year. Similarly, the themes and contents of the Boria performed by the different troupes also changes each year and can have a comical, political or satirical notion. It is common to most groups during the first ten days of Muharram Boria generally is done.