Abstract: Digital images are widely used in computer
applications. To store or transmit the uncompressed images
requires considerable storage capacity and transmission bandwidth.
Image compression is a means to perform transmission or storage of
visual data in the most economical way. This paper explains about
how images can be encoded to be transmitted in a multiplexing
time-frequency domain channel. Multiplexing involves packing
signals together whose representations are compact in the working
domain. In order to optimize transmission resources each 4 × 4
pixel block of the image is transformed by a suitable polynomial
approximation, into a minimal number of coefficients. Less than
4 × 4 coefficients in one block spares a significant amount of
transmitted information, but some information is lost. Different
approximations for image transformation have been evaluated as
polynomial representation (Vandermonde matrix), least squares +
gradient descent, 1-D Chebyshev polynomials, 2-D Chebyshev
polynomials or singular value decomposition (SVD). Results have
been compared in terms of nominal compression rate (NCR),
compression ratio (CR) and peak signal-to-noise ratio (PSNR)
in order to minimize the error function defined as the difference
between the original pixel gray levels and the approximated
polynomial output. Polynomial coefficients have been later encoded
and handled for generating chirps in a target rate of about two
chirps per 4 × 4 pixel block and then submitted to a transmission
multiplexing operation in the time-frequency domain.
Abstract: Journal bearings used in IC engines are prone to premature
failures and are likely to fail earlier than the rated life due to
highly impulsive and unstable operating conditions and frequent
starts/stops. Vibration signature extraction and wear debris analysis
techniques are prevalent in industry for condition monitoring of
rotary machinery. However, both techniques involve a great deal of
technical expertise, time, and cost. Limited literature is available on
the application of these techniques for fault detection in reciprocating
machinery, due to the complex nature of impact forces that
confounds the extraction of fault signals for vibration-based analysis
and wear prediction. In present study, a simulation model was developed to investigate
the bearing wear behaviour, resulting because of different operating
conditions, to complement the vibration analysis. In current
simulation, the dynamics of the engine was established first, based on
which the hydrodynamic journal bearing forces were evaluated by
numerical solution of the Reynold’s equation. In addition, the
essential outputs of interest in this study, critical to determine wear
rates are the tangential velocity and oil film thickness between the
journals and bearing sleeve, which if not maintained appropriately,
have a detrimental effect on the bearing performance. Archard’s wear prediction model was used in the simulation to
calculate the wear rate of bearings with specific location information
as all determinative parameters were obtained with reference to crank
rotation. Oil film thickness obtained from the model was used as a
criterion to determine if the lubrication is sufficient to prevent contact
between the journal and bearing thus causing accelerated wear. A
limiting value of 1 μm was used as the minimum oil film thickness
needed to prevent contact. The increased wear rate with growing
severity of operating conditions is analogous and comparable to the
rise in amplitude of the squared envelope of the referenced vibration
signals. Thus on one hand, the developed model demonstrated its
capability to explain wear behaviour and on the other hand it also
helps to establish a co-relation between wear based and vibration
based analysis. Therefore, the model provides a cost effective and
quick approach to predict the impending wear in IC engine bearings
under various operating conditions.
Abstract: In wireless sensor network, sensor node transmits the
sensed data to the sink node in multi-hop communication
periodically. This high traffic induces congestion at the node which is
present one-hop distance to the sink node. The packet transmission
and reception rate of these nodes should be very high, when
compared to other sensor nodes in the network. Therefore, the energy
consumption of that node is very high and this effect is known as the
“funneling effect”. The tree based-data aggregation technique
(TBDA) is used to reduce the energy consumption of the node. The
throughput of the overall performance shows a considerable decrease
in the number of packet transmissions to the sink node. The proposed
scheme, TBDA, avoids the funneling effect and extends the lifetime
of the wireless sensor network. The average case time complexity for
inserting the node in the tree is O(n log n) and for the worst case time
complexity is O(n2).
Abstract: In this paper, an attempt has been made for the design
of a robotic library using an intelligent system. The robot works on
the ARM microprocessor, motor driver circuit with 5 degrees of
freedom with Wi-Fi and GPS based communication protocol. The
authenticity of the library books is controlled by RFID. The proposed
robotic library system is facilitated with embedded system and ARM.
In this library issuance system, the previous potential readers’
authentic review reports have been taken into consideration for
recommending suitable books to the deserving new users and the
issuance of books or periodicals is based on the users’ decision. We
have conjectured that the Wi-Fi based robotic library management
system would allow fast transaction of books issuance and it also
produces quality readers.
Abstract: Test automation allows performing difficult and time
consuming manual software testing tasks efficiently, quickly and
repeatedly. However, development and maintenance of automated
tests is expensive, so it needs a proper prioritization what to automate
first. This paper describes a simple yet efficient approach for such
prioritization of test cases based on the effort needed for both manual
execution and software test automation. The suggested approach is
very flexible because it allows working with a variety of assessment
methods, and adding or removing new candidates at any time. The
theoretical ideas presented in this article have been successfully
applied in real world situations in several software companies by the
authors and their colleagues including testing of real estate websites,
cryptographic and authentication solutions, OSGi-based middleware
framework that has been applied in various systems for smart homes,
connected cars, production plants, sensors, home appliances, car head
units and engine control units (ECU), vending machines, medical
devices, industry equipment and other devices that either contain or
are connected to an embedded service gateway.
Abstract: Bottom ash from Municipal Solid Waste Incineration
(MSWI) can be viewed as a typical granular material because these
industrial by-products result from the incineration of various
domestic wastes. MSWI bottom ash is mainly used in road
engineering in substitution of the traditional natural aggregates. As
the characterization of their mechanical behavior is essential in order
to use them, specific studies have been led over the past few years. In
the first part of this paper, the mechanical behavior of MSWI bottom
ash is studied with triaxial tests. After, analysis of the experiment
results, the simulation of triaxial tests is carried out by using the
software package CESAR-LCPC. As the first approach in modeling
of this new class material, the Mohr-Coulomb model was chosen to
describe the evolution of material under the influence of external
mechanical actions.
Abstract: The paper presents a method in which the expert
knowledge is applied to fuzzy inference model. Even a less
experienced person could benefit from the use of such a system, e.g.
urban planners, officials. The analysis result is obtained in a very
short time, so a large number of the proposed locations can also be
verified in a short time. The proposed method is intended for testing
of locations of car parks in a city. The paper shows selected examples
of locations of the P&R facilities in cities planning to introduce the
P&R. The analyses of existing objects are also shown in the paper
and they are confronted with the opinions of the system users, with
particular emphasis on unpopular locations. The results of the
analyses are compared to expert analysis of the P&R facilities
location that was outsourced by the city and the opinions about
existing facilities users that were expressed on social networking
sites. The obtained results are consistent with actual users’ feedback.
The proposed method proves to be good, but does not require the
involvement of a large experts team and large financial contributions
for complicated research. The method also provides an opportunity to
show the alternative location of P&R facilities. Although the results
of the method are approximate, they are not worse than results of
analysis of employed experts. The advantage of this method is ease of
use, which simplifies the professional expert analysis. The ability of
analyzing a large number of alternative locations gives a broader
view on the problem. It is valuable that the arduous analysis of the
team of people can be replaced by the model's calculation. According
to the authors, the proposed method is also suitable for
implementation on a GIS platform.
Abstract: Maintenance and design engineers have great concern
for the functioning of rotating machineries due to the vibration
phenomenon. Improper functioning in rotating machinery originates
from the damage to rolling element bearings. The status of rolling
element bearings require advanced technologies to monitor their
health status efficiently and effectively. Avoiding vibration during
machine running conditions is a complicated process. Vibration
simulation should be carried out using suitable sensors/ transducers to
recognize the level of damage on bearing during machine operating
conditions. Various issues arising in rotating systems are interlinked
with bearing faults. This paper presents an approach for fault
diagnosis of bearings using neural networks and time/frequencydomain
vibration analysis.
Abstract: Currently, there are few user friendly Weigh-in-
Motion (WIM) data analysis softwares available which can produce
traffic input data for the recently developed AASHTOWare pavement
Mechanistic-Empirical (ME) design software. However, these
softwares have only rudimentary Quality Control (QC) processes.
Therefore, they cannot properly deal with erroneous WIM data. As
the pavement performance is highly sensible to the quality of WIM
data, it is highly recommended to use more refined QC process on
raw WIM data to get a good result. This study develops a userfriendly
software, which can produce traffic input for the ME design
software. This software takes the raw data (Class and Weight data)
collected from the WIM station and processes it with a sophisticated
QC procedure. Traffic data such as traffic volume, traffic distribution,
axle load spectra, etc. can be obtained from this software; which can
directly be used in the ME design software.
Abstract: Cochlear Implantation (CI) which became a routine
procedure for the last decades is an electronic device that provides a
sense of sound for patients who are severely and profoundly deaf.
The optimal success of this implantation depends on the electrode
technology and deep insertion techniques. However, this manual
insertion procedure may cause mechanical trauma which can lead to
severe destruction of the delicate intracochlear structure.
Accordingly, future improvement of the cochlear electrode implant
insertion needs reduction of the excessive force application during
the cochlear implantation which causes tissue damage and trauma.
This study is examined tool-tissue interaction of large prototype scale
digit embedded with distributive tactile sensor based upon cochlear
electrode and large prototype scale cochlea phantom for simulating
the human cochlear which could lead to small scale digit
requirements. The digit, distributive tactile sensors embedded with
silicon-substrate was inserted into the cochlea phantom to measure
any digit/phantom interaction and position of the digit in order to
minimize tissue and trauma damage during the electrode cochlear
insertion. The digit have provided tactile information from the digitphantom
insertion interaction such as contact status, tip penetration,
obstacles, relative shape and location, contact orientation and
multiple contacts. The tests demonstrated that even devices of such a
relative simple design with low cost have potential to improve
cochlear implant surgery and other lumen mapping applications by
providing tactile sensory feedback information and thus controlling
the insertion through sensing and control of the tip of the implant
during the insertion. In that approach, the surgeon could minimize the
tissue damage and potential damage to the delicate structures within
the cochlear caused by current manual electrode insertion of the
cochlear implantation. This approach also can be applied to other
minimally invasive surgery applications as well as diagnosis and path
navigation procedures.
Abstract: The main objective of this research is to describe the
relationship between organizational climate and organizational
citizenship behavior. In order to examine this relationship, a research
is intended to be carried out in relevant institutions and organizations
operating in the health sector in Turkey. It will be researched that
whether there is a statistically significant relationship between
organizational climate and organizational citizenship behavior
through elated scientific research methods and statistical analysis. In
addition, relationships between the dimensions of organizational
climate and organizational citizenship behavior subscales will be
questioned statistically.
Abstract: Result from the constant dwindle in natural resources,
the alternative way to reduce the costs in our daily life would be urgent
to be found in the near future. As the ancient technique based on the
theory of solar chimney since roman times, the double-skin façade are
simply composed of two large glass panels in purpose of daylighting
and also natural ventilation in the daytime. Double-skin façade is
generally installed on the exterior side of buildings as function as the
window, so there is always a huge amount of passive solar energy the
façade would receive to induce the airflow every sunny day. Therefore,
this article imposes a domestic double-skin window for residential
usage and attempts to improve the volume flow rate inside the cavity
between the panels by the frame geometry design, the installation of
outlet guide plate and the solar energy collection system. Note that the
numerical analyses are applied to investigate the characteristics of flow
field, and the boundary conditions in the simulation are totally based
on the practical experiment of the original prototype. Then we
redesign the prototype from the knowledge of the numerical results
and fluid dynamic theory, and later the experiments of modified
prototype will be conducted to verify the simulation results. The
velocities at the inlet of each case are increase by 5%, 45% and 15%
from the experimental data, and also the numerical simulation results
reported 20% improvement in volume flow rate both for the frame
geometry design and installation of outlet guide plate.
Abstract: Genetic algorithm is widely used in optimization
problems for its excellent global search capabilities and highly parallel
processing capabilities; but, it converges prematurely and has a poor
local optimization capability in actual operation. Simulated annealing
algorithm can avoid the search process falling into local optimum. A
hybrid genetic algorithm based on simulated annealing is designed by
combining the advantages of genetic algorithm and simulated
annealing algorithm. The numerical experiment represents the hybrid
genetic algorithm can be applied to solve the function optimization
problems efficiently.
Abstract: The social logic of 'Sequina' slum area in Alexandria details the integral measure of space syntax at the room-level of twenty-building samples. The essence of spatial structure integrates the central 'visitor' domain with the 'living' frontage of the 'children' zone against the segregated privacy of the opposite 'parent' depth. Meanwhile, the multifunctioning of shallow rooms optimizes the integral 'visitor' structure through graph and visibility dimensions in contrast to the 'inhabitant' structure of graph-tails out of sight. Common theme of the layout integrity increases in compensation to the decrease of room visibility. Despite the 'pheno-type' of collective integration, the individual layouts observe 'geno-type' structure of spatial diversity per room adjoins. In this regard, the layout integrity alternates the cross-correlation of the 'kitchen & living' rooms with the 'inhabitant & visitor' domains of 'motherhood' dynamic structure. Moreover, the added 'grandparent' restructures the integral measure to become the deepest space, but opens to the 'living' of 'household' integrity. Some isomorphic layouts change the integral structure just through the 'balcony' extension of access, visual or ignored 'ringiness' of space syntax. However, the most integrated or segregated layouts invert the 'geno-type' into a shallow 'inhabitant' centrality versus the remote 'visitor' structure. Overview of the multivariate social logic of spatial integrity could never clarify without the micro-data analysis.
Abstract: Lightweight and efficient structures have the aim to
enhance the efficiency of the components in various industries.
Toward this end, composites are one of the most widely used
materials because of durability, high strength and modulus, and low
weight. One type of the advanced composites is grid-stiffened
composite (GSC) structures, which have been extensively considered
in aerospace, automotive, and aircraft industries. They are one of the
top candidates for replacing some of the traditional components,
which are used here. Although there are a good number of published
surveys on the design aspects and fabrication of GSC structures, little
systematic work has been reported on their material modification to
improve their properties, to our knowledge. Matrix modification
using nanoparticles is an effective method to enhance the flexural
properties of the fibrous composites. In the present study, a silanecoupling
agent (3-glycidoxypropyltrimethoxysilane/3-GPTS) was
introduced onto the silica (SiO2) nanoparticle surface and its effects
on the three-point flexural response of isogrid E-glass/epoxy
composites were assessed. Based on the Fourier Transform Infrared
Spectrometer (FTIR) spectra, it was inferred that the 3-GPTS
coupling agent was successfully grafted onto the surface of SiO2
nanoparticles after modification. Flexural test revealed an
improvement of 16%, 14%, and 36% in stiffness, maximum load and
energy absorption of the isogrid specimen filled with 3 wt.% 3-
GPTS/SiO2 compared to the neat one. It would be worth mentioning
that in these structures, considerable energy absorption was observed
after the primary failure related to the load peak. In addition, 3-
GPTMS functionalization had a positive effect on the flexural
behavior of the multiscale isogrid composites. In conclusion, this
study suggests that the addition of modified silica nanoparticles is a
promising method to improve the flexural properties of the gridstiffened
fibrous composite structures.
Abstract: Mineral product, waste concrete (fine aggregates),
waste in the optical field, industry, and construction employ separators
to separate solids and classify them according to their size. Various
sorting machines are used in the industrial field such as those operating
under electrical properties, centrifugal force, wind power, vibration,
and magnetic force. Study on separators has been carried out to
contribute to the environmental industry. In this study, we perform
CFD analysis for understanding the basic mechanism of the separation
of waste concrete (fine aggregate) particles from air with a machine
built with a rotor with blades. In CFD, we first performed
two-dimensional particle tracking for various particle sizes for the
model with 1 degree, 1.5 degree, and 2 degree angle between each
blade to verify the boundary conditions and the method of rotating
domain method to be used in 3D. Then we developed 3D numerical
model with ANSYS CFX to calculate the air flow and track the
particles. We judged the capability of particle separation for given size
by counting the number of particles escaping from the domain toward
the exit among 10 particles issued at the inlet. We confirm that
particles experience stagnant behavior near the exit of the rotating
blades where the centrifugal force acting on the particles is in balance
with the air drag force. It was also found that the minimum particle
size that can be separated by the machine with the rotor is determined
by its capability to stay at the outlet of the rotor channels.
Abstract: This paper sets out a behavioral macro-model of a
Merged PiN and Schottky (MPS) diode based on silicon carbide
(SiC). This model holds good for both static and dynamic electrothermal
simulations for industrial applications. Its parameters have
been worked out from datasheets curves by drawing on the
optimization method: Simulated Annealing (SA) for the SiC MPS
diodes made available in the industry. The model also adopts the
Analog Behavioral Model (ABM) of PSPICE in which it has been
implemented. The thermal behavior of the devices was also taken
into consideration by making use of Foster’ canonical network as
figured out from electro-thermal measurement provided by the
manufacturer of the device.
Abstract: Manufacturing process has been considered as one of
the most important activity in business process. It correlates with
productivity and quality of the product so industries could fulfill
customer’s demand. With the increasing demand from customer,
industries must improve their manufacturing ability such as shorten
lead-time and reduce wastes on their process. Lean manufacturing
has been considered as one of the tools to waste elimination in
manufacturing or service industry. Workforce development is one
practice in lean manufacturing that can reduce waste generated from
operator such as waste of unnecessary motion. Anthropometric
approach is proposed to determine the recommended measurement in
operator’s work area. The method will get some dimensions from
Indonesia people that related to piston workstation. The result from
this research can be obtained new design for the work area
considering ergonomic aspect.
Abstract: Background modeling and subtraction in video
analysis has been widely used as an effective method for moving
objects detection in many computer vision applications. Recently, a
large number of approaches have been developed to tackle different
types of challenges in this field. However, the dynamic background
and illumination variations are the most frequently occurred problems
in the practical situation. This paper presents a favorable two-layer
model based on codebook algorithm incorporated with local binary
pattern (LBP) texture measure, targeted for handling dynamic
background and illumination variation problems. More specifically,
the first layer is designed by block-based codebook combining with
LBP histogram and mean value of each RGB color channel. Because
of the invariance of the LBP features with respect to monotonic
gray-scale changes, this layer can produce block wise detection results
with considerable tolerance of illumination variations. The pixel-based
codebook is employed to reinforce the precision from the output of the
first layer which is to eliminate false positives further. As a result, the
proposed approach can greatly promote the accuracy under the
circumstances of dynamic background and illumination changes.
Experimental results on several popular background subtraction
datasets demonstrate very competitive performance compared to
previous models.
Abstract: Polymeric composites are being increasingly used as
repair material for repairing critical infrastructures such as building,
bridge, pressure vessel, piping and pipeline. Technique in repairing
damaged pipes is one of the major concerns of pipeline owners.
Considerable researches have been carried out on the repair of
corroded pipes using composite materials. This article attempts a
short review of the subject matter to provide insight into various
techniques used in repairing corroded pipes, focusing on a wide range
of composite repair systems. These systems including pre-cured
layered, flexible wet lay-up, pre-impregnated, split composite sleeve
and flexible tape systems. Both advantages and limitations of these
repair systems were highlighted. Critical technical aspects have been
discussed through the current standards and practices. Research gaps
and future study scopes in achieving more effective design
philosophy are also presented.