Abstract: In present global scenario, aluminum alloys are
coining the attention of many innovators as competing structural
materials for automotive and space applications. Comparing to other
challenging alloys, especially, 7xxx series aluminum alloys have
been studied seriously because of benefits such as moderate strength;
better deforming characteristics and affordable cost. It is expected
that substitution of aluminum alloys for steels will result in great
improvements in energy economy, durability and recyclability.
However, it is necessary to improve the strength and the formability
levels at low temperatures in aluminum alloys for still better
applications. Aluminum–Zinc–Magnesium with or without other
wetting agent denoted as 7XXX series alloys are medium strength
heat treatable alloys. In addition to Zn, Mg as major alloying
additions, Cu, Mn and Si are the other solute elements which
contribute for the improvement in mechanical properties by suitable
heat treatment process. Subjecting to suitable treatments like age
hardening or cold deformation assisted heat treatments; known as low
temperature thermomechanical treatments (LTMT) the challenging
properties might be incorporated. T6 is the age hardening or
precipitation hardening process with artificial aging cycle whereas T8
comprises of LTMT treatment aged artificially with X% cold
deformation. When the cold deformation is provided after solution
treatment, there is increase in hardness related properties such as
wear resistance, yield and ultimate strength, toughness with the
expense of ductility. During precipitation hardening both hardness
and strength of the samples are increasing. The hardness value may
further improve when room temperature deformation is positively
supported with age hardening known as thermomechanical treatment.
It is intended to perform heat treatment and evaluate hardness, tensile
strength, wear resistance and distribution pattern of reinforcement in
the matrix. 2 to 2.5 and 3 to 3.5 times increase in hardness is reported
in age hardening and LTMT treatments respectively as compared to
as-cast composite. There was better distribution of reinforcements in
the matrix, nearly two fold increase in strength levels and up to 5
times increase in wear resistance are also observed in the present
study.
Abstract: In Electric Power Steering (EPS), spoke type
Brushless AC (BLAC) motors offer distinct advantages over other
electric motor types in terms torque smoothness, reliability and
efficiency. This paper deals with the shape optimization of spoke
type BLAC motor, in order to reduce cogging torque. This paper
examines 3 steps skewing rotor angle, optimizing rotor core edge and
rotor overlap length for reducing cogging torque in spoke type BLAC
motor. The methods were applied to existing machine designs and
their performance was calculated using finite- element analysis
(FEA). Prototypes of the machine designs were constructed and
experimental results obtained. It is shown that the FEA predicted the
cogging torque to be nearly reduce using those methods.
Abstract: In this paper, an autonomous hovering control method
of multicopter using only Web camera is proposed. Recently, various
control method of an autonomous flight for multicopter are proposed.
But, in the previous proposed methods, a motion capture system
(i. e., OptiTrack) and laser range finder are often used to measure
the position and posture of multicopter. To achieve an autonomous
flight control of multicopter with simple equipments, we propose
an autonomous flight control method using AR marker and Web
camera. AR marker can measure the position of multicopter with
Cartesian coordinate in three dimensional, then its position connects
with aileron, elevator, and accelerator throttle operation. A simple
PID control method is applied to the each operation and adjust
the controller gains. Experimental results are given to show the
effectiveness of our proposed method. Moreover, another simple
operation method for autonomous flight control multicopter is also
proposed.
Abstract: Despite the advances made in various new
technologies, application of these technologies for agriculture still
remains a formidable task, as it involves integration of diverse
domains for monitoring the different process involved in agricultural
management. Advances in ambient intelligence technology represents
one of the most powerful technology for increasing the yield of
agricultural crops and to mitigate the impact of water scarcity,
climatic change and methods for managing pests, weeds and diseases.
This paper proposes a GPS-assisted, machine to machine solutions
that combine information collected by multiple sensors for the
automated management of paddy crops. To maintain the economic
viability of paddy cultivation, the various techniques used in
agriculture are discussed and a novel system which uses ambient
intelligence technique is proposed in this paper. The ambient
intelligence based agricultural system gives a great scope.
Abstract: Numerical studies have been carried out using a
validated two-dimensional standard k-omega turbulence model for
the design optimization of a thrust vector control system using shock
induced self-impinging supersonic secondary double jet. Parametric
analytical studies have been carried out at different secondary
injection locations to identifying the highest unsymmetrical
distribution of the main gas flow due to shock waves, which produces
a desirable side force more lucratively for vectoring. The results from
the parametric studies of the case on hand reveal that the shock
induced self-impinging supersonic secondary double jet is more
efficient in certain locations at the divergent region of a CD nozzle
than a case with supersonic single jet with same mass flow rate. We
observed that the best axial location of the self-impinging supersonic
secondary double jet nozzle with a given jet interaction angle, built-in
to a CD nozzle having area ratio 1.797, is 0.991 times the primary
nozzle throat diameter from the throat location. We also observed
that the flexible steering is possible after invoking ON/OFF facility to
the secondary nozzles for meeting the onboard mission requirements.
Through our case studies we concluded that the supersonic self-impinging
secondary double jet at predesigned jet interaction angle
and location can provide more flexible steering options facilitating
with 8.81% higher thrust vectoring efficiency than the conventional
supersonic single secondary jet without compromising the payload
capability of any supersonic aerospace vehicle.
Abstract: This paper investigates the connotation, and some of
the realistic implications, of the economic reform of health sector in
under developed countries. The paper investigates the issues that
economic reforms have to address, and the policy targets they are
considered to accomplish. The work argues that the development of
economic reform is not connected only with understanding the
priorities and refining them, furthermore with reformation and
restructuring the organizations through which health policies are
employed. Considering various organizational values, that are likely
to be regular to all economic reform programs, a regulatory approach
to institutional reform is unsuitable. The paper further investigates the
selection of economic reform that may as well influence via technical
suggestions and analysis, but the verdict to continue, and the
consequent success of execution, eventually depends on the
progressive political sustainability. The paper concludes by giving
examples of institutional reforms from various underdeveloped
countries and includes recommendation of the responsibility and
control of donor organizations.
Abstract: Studying stress and strain trends in the femur and
recognizing femur failure mechanism is very important for
preventing hip fracture in the elderly. The aim of this study was to
identify high stress and strain regions in the femur during normal
walking and falling to find the mechanical behavior and failure
mechanism of the femur. We developed a finite element model of the
femur from the subject’s quantitative computed tomography (QCT)
image and used it to identify potentially high stress and strain regions
during the single-leg stance and the sideways fall. It was found that
fracture may initiate from the superior region of femoral neck and
propagate to the inferior region during a high impact force such as
sideways fall. The results of this study showed that the femur bone is
more sensitive to strain than stress which indicates the effect of
strain, in addition to effect of stress, should be considered for failure
analysis.
Abstract: In recent decades, particulate matter (PM10) have
received much attention due to its potential adverse health impact and
the subsequent need to better control or regulate these pollutants.
The aim of this paper is focused on study risk assessment of PM10
in four different districts (Shebikah, Masfalah, Aziziyah, Awali) in
Makkah, Saudi Arabia during the period from 1 Ramadan 1434 AH -
27 Safar 1435 AH. Samples were collected by using Low Volume
Sampler (LVS Low Volume Sampler) device and filtration method
for estimating the total concentration of PM10.
The study indicated that the mean PM10 concentrations were 254.6
(186.1 - 343.2) μg/m3 in Shebikah, 184.9 (145.6 - 271.4) μg/m3 in
Masfalah, 162.4 (92.4-253.8) μg/m3 in Aziziyah, and 56.0 (44.5 -
119.8) μg/m3 in Awali. These values did not exceed the permissible
limits in PME (340 μg/m3 as daily average). Furthermore, health
assessment is carried out using AirQ2.2.3 model to estimate the
number of hospital admissions due to respiratory diseases. The
cumulative number of cases per 100,000 were 1534 (18-3050 case),
which lower than that recorded in the United States, Malaysia. The
concentration response coefficient was 0.49 (95% CI 0.05 - 0.70) per
10 μg/m3 increase of PM10.
Abstract: The using of waste materials in the construction
industry can reduce the dependence on the natural aggregates which
are going at the end to deplete. The glass waste is generated in a huge
amount which can make one of its disposals in concrete industry
effective not only as a green solution but also as an advantage to
enhance the performance of mechanical properties and durability of
concrete. This article reports the performance of concrete specimens
containing different percentages of milled glass waste as a partial
replacement of cement (Powder), when they are subject to cycles of
freezing and thawing. The tests were conducted on 75-mm cubes and
75 x 75 x 300-mm prisms. Compressive strength based on laboratory
testing and non-destructive ultrasonic pulse velocity test were
performed during the action of freezing-thawing cycles (F/T). The
results revealed that the incorporation of glass waste in concrete
mixtures is not only feasible but also showed generally better strength
and durability performance than control concrete mixture. It may be
said that the recycling of waste glass in concrete mixes is not only a
disposal way, but also it can be an exploitation in concrete industry.
Abstract: SARA is a common and serious metabolic disorder in
early lactation in dairy cattle and in finishing beef cattle, caused by
diets with high inclusion of cereal grain. This experiment was
performed to determine the efficacy of Megasphaera elsdenii, a
major lactate-utilizing bacterium in prevention/treatment of SARA in
vivo. In vivo experimentation, it was used eight ruminally cannulated
rams and it was applied the rapid adaptation with the mixture of grain
based on wheat (80% wheat, 20% barley) and barley (80% barley,
20% wheat). During the systematic adaptation, it was followed the
probability of SARA formation by being measured the rumen pH
with two hours intervals after and before feeding. After being
evaluated the data, it was determined the ruminal pH ranged from
5.2-5.6 on the condition of feeding with 60 percentage of grain
mixture based on barley and wheat, that assured the definite form of
subacute acidosis. In four days SARA period, M. elsdenii (1010 cfu
ml-1) was inoculated during the first two days. During the SARA
period, it was observed the decrease of feed intake with M. elsdenii
inoculation. Inoculation of M. elsdenii was caused to differentiation
of rumen pH (P
Abstract: Greenhouses offer us suitable conditions which can
be controlled easily for the growth of the plant and they are made by
using a covering material that allows the sun light entering into the
system. Covering material can be glass, fiber glass, plastic or another
transparent element. This study investigates the solar energy usability
rates and solar energy benefitting rates of a semi-spherical (modified
arch) type greenhouse system according to different orientations and
positions which exists under climatic conditions of Bayburt. In the
concept of this study it is tried to determine the best direction and
best sizes of a semi-spherical greenhouse to get best solar benefit
from the sun. To achieve this aim a modeling study is made by using
MATLAB. However, this modeling study is run for some determined
shapes and greenhouses it can be used for different shaped
greenhouses or buildings. The basic parameters are determined as
greenhouse azimuth angle, the rate of size of long edge to short and
seasonal solar energy gaining of greenhouse. The optimum azimuth
angles of 400, 300, 250, 200, 150, 100, 50 m2 modified arch
greenhouse are 90o, 90o, 35o, 35o, 34o, 33o and 22o while their
optimum k values (ratio of length to width) are 10, 10, 10, 10, 6, 4
and 4 respectively. Positioning the buildings in order to get more
solar heat energy in winter and less in summer brings out energy and
money savings and increases the comfort.
Abstract: A knowledge base stores facts and rules about the
world that applications can use for the purpose of reasoning. By
applying the concept of granular computing to a knowledge base,
several advantages emerge. These can be harnessed by applications
to improve their capabilities and performance. In this paper, the
concept behind such a construct, called a granular knowledge cube,
is defined, and its intended use as an instrument that manages to
cope with different data types and detect knowledge domains is
elaborated. Furthermore, the underlying architecture, consisting of the
three layers of the storing, representing, and structuring of knowledge,
is described. Finally, benefits as well as challenges of deploying it
are listed alongside application types that could profit from having
such an enhanced knowledge base.
Abstract: This paper presents the design and fabrication of a
novel piezoelectric actuator for a gas micro pump with check valve
having the advantages of miniature size, light weight and low power
consumption. The micro pump is designed to have eight major
components, namely a stainless steel upper cover layer, a piezoelectric
actuator, a stainless steel diaphragm, a PDMS chamber layer, two
stainless steel channel layers with two valve seats, a PDMS check
valve layer with two cantilever-type check valves and an acrylic
substrate. A prototype of the gas micro pump, with a size of 52 mm ×
50 mm × 5.0 mm, is fabricated by precise manufacturing. This device
is designed to pump gases with the capability of performing the
self-priming and bubble-tolerant work mode by maximizing the stroke
volume of the membrane as well as the compression ratio via
minimization of the dead volume of the micro pump chamber and
channel. By experiment apparatus setup, we can get the real-time
values of the flow rate of micro pump and the displacement of the
piezoelectric actuator, simultaneously. The gas micro pump obtained
higher output performance under the sinusoidal waveform of 250 Vpp.
The micro pump achieved the maximum pumping rates of 1185
ml/min and back pressure of 7.14 kPa at the corresponding frequency
of 120 and 50 Hz.
Abstract: This study suggests the estimation method of stress
distribution for the beam structures based on TLS (Terrestrial Laser
Scanning). The main components of method are the creation of the
lattices of raw data from TLS to satisfy the suitable condition and
application of CSSI (Cubic Smoothing Spline Interpolation) for
estimating stress distribution. Estimation of stress distribution for the
structural member or the whole structure is one of the important
factors for safety evaluation of the structure. Existing sensors which
include ESG (Electric strain gauge) and LVDT (Linear Variable
Differential Transformer) can be categorized as contact type sensor
which should be installed on the structural members and also there are
various limitations such as the need of separate space where the
network cables are installed and the difficulty of access for sensor
installation in real buildings. To overcome these problems inherent in
the contact type sensors, TLS system of LiDAR (light detection and
ranging), which can measure the displacement of a target in a long
range without the influence of surrounding environment and also get
the whole shape of the structure, has been applied to the field of
structural health monitoring. The important characteristic of TLS
measuring is a formation of point clouds which has many points
including the local coordinate. Point clouds are not linear distribution
but dispersed shape. Thus, to analyze point clouds, the interpolation is
needed vitally. Through formation of averaged lattices and CSSI for
the raw data, the method which can estimate the displacement of
simple beam was developed. Also, the developed method can be
extended to calculate the strain and finally applicable to estimate a
stress distribution of a structural member. To verify the validity of the
method, the loading test on a simple beam was conducted and TLS
measured it. Through a comparison of the estimated stress and
reference stress, the validity of the method is confirmed.
Abstract: Since 1920, the industry has almost completely
changed the rivets production techniques for the manufacture of
permanent welding join production of structures and manufacture of
other products. The welding arc is the process more widely used in
industries. This is accomplished by the heat of an electric arc which
melts the base metal while the molten metal droplets are transferred
through the arc to the welding pool, protected from the atmosphere
by a gas curtain. The GMAW (Gas metal arc welding) process is
influenced by variables such as: current, polarity, welding speed,
electrode: extension, position, moving direction; type of joint,
welder's ability, among others. It is remarkable that the knowledge
and control of these variables are essential for obtaining satisfactory
quality welds, knowing that are interconnected so that changes in one
of them requiring changes in one or more of the other to produce the
desired results. The optimum values are affected by the type of base
metal, the electrode composition, the welding position and the quality
requirements. Thus, this paper proposes a new methodology, adding
the variable vibration through a mechanism developed for GMAW
welding, in order to improve the mechanical and metallurgical
properties which does not affect the ability of the welder and enables
repeatability of the welds made. For confirmation metallographic
analysis and mechanical tests were made.
Abstract: This study conducts simulation analyses to find the
optimal debt ceiling of Taiwan, while factoring in welfare
maximization under a dynamic stochastic general equilibrium
framework. The simulation is based on Taiwan's 2001 to 2011
economic data and shows that welfare is maximized at a debt/GDP
ratio of 0.2, increases in the debt/GDP ratio leads to increases in both
tax and interest rates and decreases in the consumption ratio and
working hours. The study results indicate that the optimal debt ceiling
of Taiwan is 20% of GDP, where if the debt/GDP ratio is greater than
40%, the welfare will be negative and result in welfare loss.
Abstract: Cemented carbides, owing to their excellent
mechanical properties, have been of immense interest in the field of
hard materials for the past few decades. A number of processing
techniques have been developed to obtain high quality carbide tools,
with a wide range of grain size depending on the application and
requirements. Microwave sintering is one of the heating processes,
which has been used to prepare a wide range of materials including
ceramics. A deep understanding of microwave sintering and its
contribution towards control of grain growth and on deformation of
the resulting carbide materials requires further studies and attention.
In addition, the effect of binder materials and their behavior during
microwave sintering is another area that requires clear understanding.
This review aims to focus on microwave sintering, providing
information of how the process works and what type of materials it is
best suited for. In addition, a closer look at some microwave sintered
Tungsten Carbide-Cobalt samples will be taken and discussed,
highlighting some of the key issues and challenges faced in this
research area.
Abstract: This study investigates the effects of the lead angle
and chip thickness variation on surface roughness during the
machining of compacted graphite iron using ceramic cutting tools
under dry cutting conditions. Analytical models were developed for
predicting the surface roughness values of the specimens after the
face milling process. Experimental data was collected and imported
to the artificial neural network model. A multilayer perceptron model
was used with the back propagation algorithm employing the input
parameters of lead angle, cutting speed and feed rate in connection
with chip thickness. Furthermore, analysis of variance was employed
to determine the effects of the cutting parameters on surface
roughness. Artificial neural network and regression analysis were
used to predict surface roughness. The values thus predicted were
compared with the collected experimental data, and the
corresponding percentage error was computed. Analysis results
revealed that the lead angle is the dominant factor affecting surface
roughness. Experimental results indicated an improvement in the
surface roughness value with decreasing lead angle value from 88° to
45°.
Abstract: Ant Colony Optimization (ACO) is a promising
modern approach to the unused combinatorial optimization. Here
ACO is applied to finding the shortest during communication link
failure. In this paper, the performances of the prim’s and ACO
algorithm are made. By comparing the time complexity and program
execution time as set of parameters, we demonstrate the pleasant
performance of ACO in finding excellent solution to finding shortest
path during communication link failure.
Abstract: Food poisoning and infection by bacteria are of public
health significance to both developing and developed countries.
Samples of ogi (akamu) prepared from white and yellow variety of
maize sold in Uturu and Okigwe were analyzed together with the
laboratory prepared ogi for bacterial quality using the standard
microbiological methods. The analyses showed that both white and
yellow variety had total bacterial counts (cfu/g) of 4.0 ×107 and 3.9 x
107 for the laboratory prepared ogi while the commercial ogi had 5.2
x 107 and 4.9 x107, 4.9 x107 and 4.5 x107, 5.4 x107 and 5.0 x107 for
Eke-Okigwe, Up-gate and Nkwo-Achara market respectively. The
Staphylococcal counts ranged from 2.0 x 102 to 5.0 x102 and 1.0 x
102 to 4.0 x102 for the white and yellow variety from the different
markets while Staphylococcal growth was not recorded on the
laboratory prepared ogi. The laboratory prepared ogi had no Coliform
growth while the commercially prepared ogi had counts of 0.5 x103
to 1.6 x 103 for white variety and 0.3 x 103 to 1.1 x103 for yellow
variety respectively. The Lactic acid bacterial count of 3.5x106 and
3.0x106 was recorded for the laboratory ogi while the commercially
prepared ogi ranged from 3.2x106 to 4.2x106 (white variety) and 3.0
x106 to 3.9 x106 (yellow). The presence of bacteria isolates from the
commercial and laboratory fermented ogi showed that Lactobacillus
sp, Leuconostoc sp and Citrobacter sp were present in all the
samples, Micrococcus sp and Klebsiella sp were isolated from Eke-
Okigwe and ABSU-up-gate markets varieties respectively, E. coli
and Staphylococcus sp were present in Eke-Okigwe and Nkwo-
Achara markets while Salmonella sp were isolated from the three
markets. Hence, there are chances of contracting food borne diseases
from commercially prepared ogi. Therefore, there is the need for
sanitary measures in the production of fermented cereals so as to
minimize the rate of food borne pathogens during processing and
storage.