Abstract: Truncated multiplier is a good candidate for digital
signal processing (DSP) applications including finite impulse
response (FIR) and discrete cosine transform (DCT). Through
truncated multiplier a significant reduction in Field Programmable
Gate Array (FPGA) resources can be achieved. This paper presents
for the first time a comparison of resource utilization of Spartan-3AN
and Virtex-5 implementation of standard and truncated multipliers
using Very High Speed Integrated Circuit Hardware Description
Language (VHDL). The Virtex-5 FPGA shows significant
improvement as compared to Spartan-3AN FPGA device. The
Virtex-5 FPGA device shows better performance with a percentage
ratio of number of occupied slices for standard to truncated
multipliers is increased from 40% to 73.86% as compared to Spartan-
3AN is decreased from 68.75% to 58.78%. Results show that the
anomaly in Spartan-3AN FPGA device average connection and
maximum pin delay have been efficiently reduced in Virtex-5 FPGA
device.
Abstract: More and more natural disasters are happening every
year: floods, earthquakes, volcanic eruptions, etc. In order to reduce
the risk of possible damages, governments all around the world are
investing into development of Early Warning Systems (EWS) for
environmental applications. The most important task of the EWS is
identification of the onset of critical situations affecting environment
and population, early enough to inform the authorities and general
public. This paper describes an approach for monitoring of flood
protections systems based on machine learning methods. An
Artificial Intelligence (AI) component has been developed for
detection of abnormal dike behaviour. The AI module has been
integrated into an EWS platform of the UrbanFlood project (EU
Seventh Framework Programme) and validated on real-time
measurements from the sensors installed in a dike.
Abstract: In this paper, a field oriented control (FOC) induction motor drive is presented. In order to eliminate the speed sensor, an adaptation algorithm for tuning the rotor speed is proposed. Based on the Model Reference Adaptive System (MRAS) scheme, the rotor speed is tuned to obtain an exact FOC induction motor drive. The reference and adjustable models, developed in stationary stator reference frame, are used in the MRAS scheme to estimate induction rotor speed from measured terminal voltages and currents. The Integral Proportional (IP) gains speed controller are tuned by a modern approach that is the Particle Swarm Optimization (PSO) algorithm in order to optimize the parameters of the IP controller. The use of PSO as an optimization algorithm makes the drive robust, with faster dynamic response, higher accuracy and insensitive to load variation. The proposed algorithm has been tested by numerical simulation, showing the capability of driving load.
Abstract: Software Architecture plays a key role in software development but absence of formal description of Software Architecture causes different impede in software development. To cope with these difficulties, ontology has been used as artifact. This paper proposes ontology for Software Architectural design based on IEEE model for architecture description and Kruchten 4+1 model for viewpoints classification. For categorization of style and views, ISO/IEC 42010 has been used. Corpus method has been used to evaluate ontology. The main aim of the proposed ontology is to classify and locate Software Architectural design information.
Abstract: There are many views on how human decision makers behave. In this work, the Justices of the United States Supreme Court will be viewed in terms of constrained maximization and cognitivecybernetic theory. This paper will integrate research in such fields as law, political science, psychology, economics and decision making theory. It will be argued that due to its heavy workload, the Supreme Court is forced to make decisions in a boundedly rational manner. The ideas and theory put forward here will be tested in the area of the Court’s decisions involving religion. Therefore, the cases involving the U.S. Constitution’s Free Exercise Clause and Establishment Clause will be analyzed. Also, variables such as the U.S. government’s involvement in these cases will be considered. The years to be studied will be 1987-2011.
Abstract: Equal Channel Angular Pressing (ECAP) is currently
being widely investigated because of its potential to produce ultrafine
grained microstructures in metals and alloys. A sound
knowledge of the plastic deformation and strain distribution is
necessary for understanding the relationships between strain
inhomogeneity and die geometry. Considerable research has been
reported on finite element analysis of this process, assuming threedimensional
plane strain condition. However, the two-dimensional
models are not suitable due to the geometry of the dies, especially in
cylindrical ones. In the present work, three-dimensional simulation of
ECAP process was carried out for six outer corner radii (sharp to 10
mm in steps of 2 mm), with channel angle 105¶Çü▒, for strain hardening
aluminium alloy (AA 6101) using ABAQUS/Standard software.
Strain inhomogeneity is presented and discussed for all cases. Pattern
of strain variation along selected radial lines in the body of the workpiece
is presented. It is found from the results that the outer corner
has a significant influence on the strain distribution in the body of
work-piece. Based on inhomogeneity and average strain criteria,
there is an optimum outer corner radius.
Abstract: This study discusses the stumbling blocks stifling the
adoption of GPS technology in the public sector of Pakistan. This
study has been carried out in order to describe the value of GPS
technology and its adoption at various public sector organisations in
Pakistan. Sample size for the research conducted was 200; personnel
working in public sector having age above 29 years were surveyed.
Data collected for this research has been quantitatively analysed with
the help of SPSS. Regression analysis, correlation and cross
tabulation were the techniques used to determine the strength of
relationship between key variables. Findings of this research indicate
that main hurdles in GPS adoption in the public sector of Pakistan are
lack of awareness about GPS among masses in general and the
stakeholders in particular, lack of initiative on part of government in
promoting new technologies, unavailability of GPS infrastructure in
Pakistan and prohibitions on map availability because of security
reasons.
Abstract: During last decades, worldwide researchers dedicated
efforts to develop machine-based seismic Early Warning systems,
aiming at reducing the huge human losses and economic damages.
The elaboration time of seismic waveforms is to be reduced in order
to increase the time interval available for the activation of safety
measures. This paper suggests a Data Mining model able to correctly
and quickly estimate dangerousness of the running seismic event.
Several thousand seismic recordings of Japanese and Italian
earthquakes were analyzed and a model was obtained by means of a
Bayesian Network (BN), which was tested just over the first
recordings of seismic events in order to reduce the decision time and
the test results were very satisfactory.
The model was integrated within an Early Warning System
prototype able to collect and elaborate data from a seismic sensor
network, estimate the dangerousness of the running earthquake and
take the decision of activating the warning promptly.
Abstract: The need for reputation assessment is particularly strong in peer-to-peer (P2P) systems because the peers' personal site autonomy is amplified by the inherent technological decentralization of the environment. However, the decentralization notion makes the problem of designing a peer-to-peer based reputation assessment substantially harder in P2P networks than in centralized settings.Existing reputation systems tackle the reputation assessment process in an ad-hoc manner. There is no systematic and coherent way to derive measures and analyze the current reputation systems. In this paper, we propose a reputation assessment process and use it to classify the existing reputation systems. Simulation experiments are conducted and focused on the different methods in selecting the recommendation sources and retrieving the recommendations. These two phases can contribute significantly to the overall performance due to communication cost and coverage.
Abstract: Air infiltration in mass scale industrial applications of
bio char production is inevitable. The presence of oxygen during the
carbonization process is detrimental to the production of biochar yield
and properties. The experiment was carried out on several wood
species in a fixed-bed pyrolyser under various fractions of oxygen
ranging from 0% to 11% by varying nitrogen and oxygen composition
in the pyrolysing gas mixtures at desired compositions. The bed
temperature and holding time were also varied. Process optimization
was carried out by Response Surface Methodology (RSM) by
employing Central Composite Design (CCD) using Design Expert 6.0
Software. The effect of oxygen ratio and holding time on biochar yield
within the range studied were statistically significant. From the
analysis result, optimum condition of 15.2% biochar yield of
mangrove wood was predicted at pyrolysis temperature of 403 oC,
oxygen percentage of 2.3% and holding time of two hours. This
prediction agreed well with the experiment finding of 15.1% biochar
yield.
Abstract: This research presents the development of simulation
modeling for WIP management in semiconductor fabrication.
Manufacturing simulation modeling is needed for productivity
optimization analysis due to the complex process flows involved
more than 35 percent re-entrance processing steps more than 15 times
at same equipment. Furthermore, semiconductor fabrication required
to produce high product mixed with total processing steps varies from
300 to 800 steps and cycle time between 30 to 70 days. Besides the
complexity, expansive wafer cost that potentially impact the
company profits margin once miss due date is another motivation to
explore options to experiment any analysis using simulation
modeling. In this paper, the simulation model is developed using
existing commercial software platform AutoSched AP, with
customized integration with Manufacturing Execution Systems
(MES) and Advanced Productivity Family (APF) for data collections
used to configure the model parameters and data source. Model
parameters such as processing steps cycle time, equipment
performance, handling time, efficiency of operator are collected
through this customization. Once the parameters are validated, few
customizations are made to ensure the prior model is executed. The
accuracy for the simulation model is validated with the actual output
per day for all equipments. The comparison analysis from result of
the simulation model compared to actual for achieved 95 percent
accuracy for 30 days. This model later was used to perform various
what if analysis to understand impacts on cycle time and overall
output. By using this simulation model, complex manufacturing
environment like semiconductor fabrication (fab) now have
alternative source of validation for any new requirements impact
analysis.
Abstract: Usually, the solid-fuel flow of an iron ore sinter plant
consists of different types of the solid-fuels, which differ from each
other. Information about the composition of the solid-fuel flow
usually comes every 8-24 hours. It can be clearly seen that this
information cannot be used to control the sintering process in real
time. Due to this, we propose an expert system which uses indirect
measurements from the process in order to obtain the composition of
the solid-fuel flow by solving an optimization task. Then this
information can be used to control the sintering process. The
proposed technique can be successfully used to improve sinter
quality and reduce the amount of solid-fuel used by the process.
Abstract: In two studies we challenged the well consolidated
position in regret literature according to which the necessary
condition for the emergence of regret is a bad outcome ensuing from
free decisions. Without free choice, and, consequently, personal
responsibility, other emotions, such as disappointment, but not regret,
are supposed to be elicited. In our opinion, a main source of regret is
being obliged by circumstance out of our control to chose an
undesired option. We tested the hypothesis that regret resulting from
a forced choice is more intense than regret derived from a free choice
and that the outcome affects the latter, not the former. Besides, we
investigated whether two other variables – the perception of the level
of freedom of the choice and the choice justifiability – mediated the
relationships between choice and regret, as well as the other four
emotions we examined: satisfaction, anger toward oneself,
disappointment, anger towards circumstances. The two studies were
based on the scenario methodology and implied a 2 x 2 (choice x
outcome) between design. In the first study the foreseen short-term
effects of the choice were assessed; in the second study the
experienced long-term effects of the choice were assessed. In each
study 160 students of the Second University of Naples participated.
Results largely corroborated our hypotheses. They were discussed in
the light of the main theories on regret and decision making.
Abstract: Corporate social responsibility (CSR) viewpoint have challenged the traditional perception to understand corporations position. Production- and managerial-centred views are expanding towards reference group-centred policies. Consequently, the significance of new kind of knowledge has emerged. In addition to management of the organisation, the idea of CSR emphasises the importance to recognise the value-expectations of operational environment. It is know that management is often well-aware of corporate social responsibilities, but it is less clear how well these high level goals are understood in practical product design and development work. In this study, the apprehension above proved to be real to some degree. While management was very aware of CSR it was less familiar to designers. The outcome shows that it is essential to raise ethical values and issues higher in corporate communication, if it is wished that they materialize also in products.
Abstract: Landfill gas, particularly methane is one of the
greenhouse gases which contributes to global warming. This paper presents the findings of a study on methane gas production from
simulated landfill reactor under saturated conditions. A reactor was constructed to represent a landfill cell of 2.5 m thickness on sandy
soil. The reactor was 0.2 m in diameter and 4 m in height. One meter of sand and pebble layer was packed at the bottom of the reactor
followed by 2.5 m of solid waste layer and 0.4 m of sand layer as the cover soil. Degradation of waste in the solid waste layer was at
acidification stage as indicated by the leachate quality with COD as
high as 55,511 mg/L and pH as low as 5.1. However, methanogenic
environment was established at the bottom sand layer after one year of operation indicated by pH of 7.2 and methane gas generation.
Leachate degradation took place as the leachate moved through the
sand layer at an infiltration of rate 0.7 cm/day. This resulted in landfill gas production of 77 mL/day/kg containing 55 to 65% methane. The application of sand layer contributed to the gas
production from landfill by an in-situ degradation of leachate in the
sand at the bottom of the landfill.
Abstract: In this paper, the effects of radiation, chemical
reaction and double dispersion on mixed convection heat and mass
transfer along a semi vertical plate are considered. The plate is
embedded in a Newtonian fluid saturated non - Darcy (Forchheimer
flow model) porous medium. The Forchheimer extension and first
order chemical reaction are considered in the flow equations. The
governing sets of partial differential equations are nondimensionalized
and reduced to a set of ordinary differential
equations which are then solved numerically by Fourth order Runge–
Kutta method. Numerical results for the detail of the velocity,
temperature, and concentration profiles as well as heat transfer rates
(Nusselt number) and mass transfer rates (Sherwood number) against
various parameters are presented in graphs. The obtained results are
checked against previously published work for special cases of the
problem and are found to be in good agreement.
Abstract: An evolutionary method whose selection and recombination
operations are based on generalization error-bounds of
support vector machine (SVM) can select a subset of potentially
informative genes for SVM classifier very efficiently [7]. In this
paper, we will use the derivative of error-bound (first-order criteria)
to select and recombine gene features in the evolutionary process,
and compare the performance of the derivative of error-bound with
the error-bound itself (zero-order) in the evolutionary process. We
also investigate several error-bounds and their derivatives to compare
the performance, and find the best criteria for gene selection
and classification. We use 7 cancer-related human gene expression
datasets to evaluate the performance of the zero-order and first-order
criteria of error-bounds. Though both criteria have the same strategy
in theoretically, experimental results demonstrate the best criterion
for microarray gene expression data.
Abstract: Documents retrieval in Information Retrieval
Systems (IRS) is generally about understanding of
information in the documents concern. The more the system
able to understand the contents of documents the more
effective will be the retrieval outcomes. But understanding of the
contents is a very complex task. Conventional IRS apply algorithms
that can only approximate the meaning of document contents through
keywords approach using vector space model. Keywords may be
unstemmed or stemmed. When keywords are stemmed and conflated
in retrieving process, we are a step forwards in applying semantic
technology in IRS. Word stemming is a process in morphological
analysis under natural language processing, before syntactic and
semantic analysis. We have developed algorithms for Malay and
Arabic and incorporated stemming in our experimental systems in
order to measure retrieval effectiveness. The results have shown that
the retrieval effectiveness has increased when stemming is used in
the systems.
Abstract: In literature, there are metrics for identifying the
quality of reusable components but the framework that makes use of
these metrics to precisely predict reusability of software components
is still need to be worked out. These reusability metrics if identified
in the design phase or even in the coding phase can help us to reduce
the rework by improving quality of reuse of the software component
and hence improve the productivity due to probabilistic increase in
the reuse level. As CK metric suit is most widely used metrics for
extraction of structural features of an object oriented (OO) software;
So, in this study, tuned CK metric suit i.e. WMC, DIT, NOC, CBO
and LCOM, is used to obtain the structural analysis of OO-based
software components. An algorithm has been proposed in which the
inputs can be given to K-Means Clustering system in form of
tuned values of the OO software component and decision tree is
formed for the 10-fold cross validation of data to evaluate the in
terms of linguistic reusability value of the component. The developed
reusability model has produced high precision results as desired.
Abstract: Protective coatings that resist oxide scale growth and
decrease chromium evaporation are necessary to make stainless steel
interconnect materials for long-term durable operation of solid oxide
fuel cells (SOFCs). In this study a layer of cobalt was electroplated
on the surface of AISI 441 ferritic stainless steel which is used in
solid oxide fuel cells for interconnect applications. The oxidation
behavior of coated substrates was studied as a function of time at
operating conditions of SOFCs. Cyclic oxidation has been also tested
at 800ºC for 100 cycles. Cobalt coating during isothermal oxidation
caused to the oxide growth resistance by limiting the outward
diffusion of Cr cation and the inward diffusion of oxygen anion.
Results of cyclic oxidation exhibited that coated substrates
demonstrate an excellent resistance against the spallation and
cracking.