Abstract: In this paper, the authors take a look at advantages of
multiphase induction motors comparing them with three phase ones
and present the applications where six-phase induction motors are
used. They elaborate the mathematical model of six-phase induction
motor with two similar stator three phase winding, shifted by 30
degrees in space and three phase winding in rotor, in synchronous
reference frame for soft starting and scalar control. The authors
simulate and discuss results of speed and torque starting transients.
Abstract: Condition monitoring of electrical power equipment
has attracted considerable attention for many years. The aim of this
paper is to use Labview with Fuzzy Logic controller to build a
simulation system to diagnose transformer faults and monitor its
condition. The front panel of the system was designed using
LabVIEW to enable computer to act as customer-designed
instrument. The dissolved gas-in-oil analysis (DGA) method was
used as technique for oil type transformer diagnosis; meanwhile
terminal voltages and currents analysis method was used for dry type
transformer. Fuzzy Logic was used as expert system that assesses all
information keyed in at the front panel to diagnose and predict the
condition of the transformer. The outcome of the Fuzzy Logic
interpretation will be displayed at front panel of LabVIEW to show
the user the conditions of the transformer at any time.
Abstract: In this paper stress and strain for two rotating thin
wall cylinder fitted together with initial interference and overlap are
computed. Also stress value for variation of initial interference is
calculated.
At first problem is considered without rotation and next angular
velocity increased from 0 to 50000 rev/min and stress in each stage
is calculated. The important point is that when stress become very
small in magnitude the angular velocity is critical and two cylinders
will separate. The critical speed i.e. speed of separation is calculated
in each step.
Abstract: The world's population continues to grow at a quarter of a million people per day, increasing the consumption of energy. This has made the world to face the problem of energy crisis now days. In response to the energy crisis, the principles of renewable energy gained popularity. There are much advancement made in developing the wind and solar energy farms across the world. These energy farms are not enough to meet the energy requirement of world. This has attracted investors to procure new sources of energy to be substituted. Among these sources, extraction of energy from the waves is considered as best option. The world oceans contain enough energy to meet the requirement of world. Significant advancements in design and technology are being made to make waves as a continuous source of energy. One major hurdle in launching wave energy devices in a developing country like Pakistan is the initial cost. A simple, reliable and cost effective wave energy converter (WEC) is required to meet the nation-s energy need. This paper will present a novel design proposed by team SAS for harnessing wave energy. This paper has three major sections. The first section will give a brief and concise view of ocean wave creation, propagation and the energy carried by them. The second section will explain the designing of SAS-2. A gear chain mechanism is used for transferring the energy from the buoy to a rotary generator. The third section will explain the manufacturing of scaled down model for SAS-2 .Many modifications are made in the trouble shooting stage. The design of SAS-2 is simple and very less maintenance is required. SAS-2 is producing electricity at Clifton. The initial cost of SAS-2 is very low. This has proved SAS- 2 as one of the cost effective and reliable source of harnessing wave energy for developing countries.
Abstract: The goal of this project is to design a system to
recognition voice commands. Most of voice recognition systems
contain two main modules as follow “feature extraction" and “feature
matching". In this project, MFCC algorithm is used to simulate
feature extraction module. Using this algorithm, the cepstral
coefficients are calculated on mel frequency scale. VQ (vector
quantization) method will be used for reduction of amount of data to
decrease computation time. In the feature matching stage Euclidean
distance is applied as similarity criterion. Because of high accuracy
of used algorithms, the accuracy of this voice command system is
high. Using these algorithms, by at least 5 times repetition for each
command, in a single training session, and then twice in each testing
session zero error rate in recognition of commands is achieved.
Abstract: Today, the Internet based communication has widen
the opportunity of event monitoring system in the medical field.
There is always a need of analyzing and designing secure and reliable
mobile communication between the hospital and biomedical
engineers mobile units. This study has been carried out to find
possible solution using SIP-based event notification for alerting the
technical staff about the Biomedical Device (BMD) status and
Patients treatment session. The Session Initiation Protocol (SIP) can
be used to create a medical event notification system. SIP can work
on a variety of devices. Its adoption as the protocol of choice for third
generation wireless networks allows for a robust and scalable
environment. One of the advantages of SIP is that it supports personal
mobility through the separation of user addressing and device
addressing. The solution for Telemed alert notification system is
based on SIP - Specific Event Notification. The aim of this project is
to extend mobility service to the hospital technicians who are using
Telemedicine system.
Abstract: Perspective of food security in 21 century showed
shortage of food that production is faced to vital problem. Food
security strategy is applied longtime method to assess required food.
Meanwhile, nanotechnology revolution changes the world face.
Nanotechnology is adequate method utilize of its characteristics to
decrease environmental problems and possible further access to food
for small farmers. This article will show impact of production and
adoption of nanocrops on food security. Population is researchers of
agricultural research center of Esfahan province. The results of study
show that there was a relationship between uses, conversion,
distribution, and production of nanocrops, operative human
resources, operative circumstance, and constrains of usage of
nanocrops and food security. Multivariate regression analysis by
enter model shows that operative circumstance, use, production and
constrains of usage of nanocrops had positive impact on food security
and they determine in four steps 20 percent of it.
Abstract: The aim of this paper is to present a methodology in
three steps to forecast supply chain demand. In first step, various data
mining techniques are applied in order to prepare data for entering
into forecasting models. In second step, the modeling step, an
artificial neural network and support vector machine is presented
after defining Mean Absolute Percentage Error index for measuring
error. The structure of artificial neural network is selected based on
previous researchers' results and in this article the accuracy of
network is increased by using sensitivity analysis. The best forecast
for classical forecasting methods (Moving Average, Exponential
Smoothing, and Exponential Smoothing with Trend) is resulted based
on prepared data and this forecast is compared with result of support
vector machine and proposed artificial neural network. The results
show that artificial neural network can forecast more precisely in
comparison with other methods. Finally, forecasting methods'
stability is analyzed by using raw data and even the effectiveness of
clustering analysis is measured.
Abstract: Numerical simulations are performed for laminar
continuous and pulsed jets impinging on a surface in order to
investigate the effects of pulsing frequency on the heat transfer
characteristics. The time-averaged Nusselt number of pulsed jets is
larger in the impinging jet region as compared to the continuous jet,
while it is smaller in the outer wall jet region. At the stagnation point,
the mean and RMS Nusselt numbers become larger and smaller,
respectively, as the pulsing frequency increases. Unsteady behaviors
of vortical fluid motions and temperature field are also investigated to
understand the underlying mechanisms of heat transfer enhancement.
Abstract: This paper presents the impact study of GTO Controlled Series Capacitor (GCSC) parameters on measured impedance (Zseen) by MHO distance relays for single transmission line high voltage 220 kV in the presence of single phase to earth fault with fault resistance (RF). The study deals with a 220 kV single electrical transmission line of Eastern Algerian transmission networks at Group Sonelgaz (Algerian Company of Electrical and Gas) compensated by series Flexible AC Transmission System (FACTS) i.e. GCSC connected at midpoint of the transmission line. The transmitted active and reactive powers are controlled by three GCSC-s. The effects of maximum reactive power injected as well as injected maximum voltage by GCSC on distance relays measured impedance is treated. The simulations results investigate the effects of GCSC injected parameters: variable reactance (XGCSC), variable voltage (VGCSC) and reactive power injected (QGCSC) on measured resistance and reactance in the presence of earth fault with resistance fault varied between 5 to 50 Ω for three cases study.
Abstract: Risk of infectious disease outbreaks is related to the
hygiene among the population. To assess the actual risks and modify
the relevant emergency procedures if necessary, a hygiene survey
was conducted among undergraduate students on the Rhodes
University campus. Soap was available to 10.5% and only 26.8% of
the study participants followed proper hygiene in relation to food
consumption. This combination increases the risk of infectious
disease outbreaks at the campus. Around 83.6% were willing to wash
their hands if soap was provided. Procurement and availability of
soap in undergraduate residences on campus should be improved, as
the total cost is estimated at only 2000 USD per annum. Awareness
campaigns about food-related hygiene and the need for regular handwashing
with soap should be run among Rhodes University students.
If successful, rates of respiratory and hygiene-related diseases will be
decreased and emergency health management simplified.
Abstract: Today with the rapid growth of telecommunications equipment, electronic and developing more and more networks of power, influence of electromagnetic waves on one another has become hot topic discussions. So in this article, this issue and appropriate mechanisms for EMC operations have been presented. First, impact of high voltage lines on the surrounding environment especially on the control room has been investigated, then to reduce electromagnetic radiation, various methods of shielding are provided and shielding effectiveness of them has been compared. It should be expressed that simulations have been done by the finite element method (FEM).
Abstract: Synthesis gas manufacturing by steam reforming of hydrocarbons is an important industrial process. High endothermic nature of the process makes it one of the most cost and heat intensive processes. In the present work, composite effect of different inert gases on synthesis gas yield, feed gas conversion and temperature distribution along the reactor length has been studied using a heterogeneous model. Mathematical model was developed as a first stage and validated against the existing process models. With the addition of inert gases, a higher yield of synthesis gas is observed. Simultaneously the rector outlet temperature drops to as low as 810 K. It was found that Xenon gives the highest yield and conversion while Helium gives the lowest temperature. Using Xenon inert gas 20 percent reduction in outlet temperature was observed compared to traditional case.
Abstract: This paper presents two simplified models to
determine nodal voltages in power distribution networks. These
models allow estimating the impact of the installation of reactive
power compensations equipments like fixed or switched capacitor
banks. The procedure used to develop the models is similar to the
procedure used to develop linear power flow models of transmission
lines, which have been widely used in optimization problems of
operation planning and system expansion. The steady state non-linear
load flow equations are approximated by linear equations relating the
voltage amplitude and currents. The approximations of the linear
equations are based on the high relationship between line resistance
and line reactance (ratio R/X), which is valid for power distribution
networks. The performance and accuracy of the models are evaluated
through comparisons with the exact results obtained from the
solution of the load flow using two test networks: a hypothetical
network with 23 nodes and a real network with 217 nodes.
Abstract: A 10bit, 40 MSps, sample and hold, implemented in 0.18-μm CMOS technology with 3.3V supply, is presented for application in the front-end stage of an analog-to-digital converter. Topology selection, biasing, compensation and common mode feedback are discussed. Cascode technique has been used to increase the dc gain. The proposed opamp provides 149MHz unity-gain bandwidth (wu), 80 degree phase margin and a differential peak to peak output swing more than 2.5v. The circuit has 55db Total Harmonic Distortion (THD), using the improved fully differential two stage operational amplifier of 91.7dB gain. The power dissipation of the designed sample and hold is 4.7mw. The designed system demonstrates relatively suitable response in different process, temperature and supply corners (PVT corners).
Abstract: This paper describes a CMOS four-quadrant
multiplier intended for use in the front-end receiver by utilizing the
square-law characteristic of the MOS transistor in the saturation
region. The circuit is based on 0.35 um CMOS technology simulated
using HSPICE software. The mixer has a third-order inter the power
consumption is 271uW from a single 1.2V power supply. One of the
features of the proposed design is using two MOS transistors
limitation to reduce the supply voltage, which leads to reduce the
power consumption. This technique provides a GHz bandwidth
response and low power consumption.
Abstract: The dynamics of User Datagram Protocol (UDP) traffic
over Ethernet between two computers are analyzed using nonlinear
dynamics which shows that there are two clear regimes in the data
flow: free flow and saturated. The two most important variables
affecting this are the packet size and packet flow rate. However,
this transition is due to a transcritical bifurcation rather than phase
transition in models such as in vehicle traffic or theorized large-scale
computer network congestion. It is hoped this model will help lay
the groundwork for further research on the dynamics of networks,
especially computer networks.
Abstract: The increased number of automobiles in recent years
has resulted in great demand for fossil fuel. This has led to the
development of automobile by using alternative fuels which include
gaseous fuels, biofuels and vegetables oils as fuel. Energy from
biomass and more specific bio-diesel is one of the opportunities that
could cover the future demand of fossil fuel shortage. Biomass in the
form of cashew nut shell represents a new energy source and
abundant source of energy in India. The bio-fuel is derived from
cashew nut shell oil and its blend with diesel are promising
alternative fuel for diesel engine. In this work the pyrolysis Cashew
Nut Shell Liquid (CNSL)-Diesel Blends (CDB) was used to run the
Direct Injection (DI) diesel engine. The experiments were conducted
with various blends of CNSL and Diesel namely B20, B40, B60, B80
and B100. The results are compared with neat diesel operation. The
brake thermal efficiency was decreased for blends of CNSL and
Diesel except the lower blends of B20. The brake thermal efficiency
of B20 is nearly closer to that of diesel fuel. Also the emission level
of the all CNSL and Diesel blends was increased compared to neat
diesel. The higher viscosity and lower volatility of CNSL leads to
poor mixture formation and hence lower brake thermal efficiency and
higher emission levels. The higher emission level can be reduced by
adding suitable additives and oxygenates with CNSL and Diesel
blends.
Abstract: This paper presents the significant factor and give
some suggestion that should know before design. The main objective of this paper is guide the first step for someone who attends to design of grounding system before study in details later. The overview of
grounding system can protect damage from fault such as can save a human life and power system equipment. The unsafe conditions have
three cases. Case 1) maximum touch voltage exceeds the safety
criteria. In this case, the conductor compression ratio of the ground gird should be first adjusted to have optimal spacing of ground grid
conductors. If it still over limit, earth resistivity should be consider afterward. Case 2) maximum step voltage exceeds the safety criteria.
In this case, increasing the number of ground grid conductors around
the boundary can solve this problem. Case 3) both of maximum touch
and step voltage exceed the safety criteria. In this case, follow the solutions explained in case 1 and case 2. Another suggestion, vary depth of ground grid until maximum step and touch voltage do not
exceed the safety criteria.
Abstract: In this paper, a tooth shape optimization method for
cogging torque reduction in Permanent Magnet (PM) motors is
developed by using the Reduced Basis Technique (RBT) coupled by
Finite Element Analysis (FEA) and Design of Experiments (DOE)
methods. The primary objective of the method is to reduce the
enormous number of design variables required to define the tooth
shape. RBT is a weighted combination of several basis shapes. The
aim of the method is to find the best combination using the weights
for each tooth shape as the design variables. A multi-level design
process is developed to find suitable basis shapes or trial shapes at
each level that can be used in the reduced basis technique. Each level
is treated as a separated optimization problem until the required
objective – minimum cogging torque – is achieved. The process is
started with geometrically simple basis shapes that are defined by
their shape co-ordinates. The experimental design of Taguchi method
is used to build the approximation model and to perform
optimization. This method is demonstrated on the tooth shape
optimization of a 8-poles/12-slots PM motor.