Abstract: Response Surface Methodology (RSM) is a powerful
and efficient mathematical approach widely applied in the
optimization of cultivation process. Cellulase enzyme production by
Trichoderma reesei RutC30 using agricultural waste rice straw and
banana fiber as carbon source were investigated. In this work,
sequential optimization strategy based statistical design was
employed to enhance the production of cellulase enzyme through
submerged cultivation. A fractional factorial design (26-2) was applied
to elucidate the process parameters that significantly affect cellulase
production. Temperature, Substrate concentration, Inducer
concentration, pH, inoculum age and agitation speed were identified
as important process parameters effecting cellulase enzyme synthesis.
The concentration of lignocelluloses and lactose (inducer) in the
cultivation medium were found to be most significant factors. The
steepest ascent method was used to locate the optimal domain and a
Central Composite Design (CCD) was used to estimate the quadratic
response surface from which the factor levels for maximum
production of cellulase were determined.
Abstract: Viscous heating becomes significant in the high speed
resin coating process of glass fibers for optical fiber manufacturing.
This study focuses on the coating resin flows inside the capillary
coating die of optical fiber coating applicator and they are numerically
simulated to examine the effects of viscous heating and subsequent
temperature increase in coating resin. Resin flows are driven by fast
moving glass fiber and the pressurization at the coating die inlet, while
the temperature dependent viscosity of liquid coating resin plays an
important role in the resin flow. It is found that the severe viscous
heating near the coating die wall profoundly alters the radial velocity
profiles and that the increase of final coating thickness by die
pressurization is amplified if viscous heating is present.
Abstract: The present study was conducted to observe the effect
of Plantago psyllium on blood glucose and cholesterol levels in
normal and alloxan induced diabetic rats. To investigate the effect of
Plantago psyllium 40 rats were included in this study divided into
four groups of ten rats in each group. One group A was normal,
second group B was diabetic, third group C was non diabetic and
hypercholesterolemic and fourth group D was diabetic and
hypercholesterolemic. Two groups B and D were made diabetic by
intraperitonial injection of alloxan dissolved in 1mL distilled water at
a dose of 125mg/Kg of body weight. Two groups C and D were
made hypercholesterolemic by oral administration of powder
cholesterol (1g/Kg of body weight). The blood samples from all the
rats were collected from coccygial vein on 1st day, then on 21st and
42nd day respectively. All the samples were analyzed for blood
glucose and cholesterol level by using enzymatic kits. The blood
glucose and cholesterol levels of treated groups of rats showed
significant reduction after 7 weeks of treatment with Plantago
psyllium. By statistical analysis of results it was found that Plantago
psyllium has anti-diabetic and hypocholesterolemic activity in
diabetic and hypercholesterolemic albino rats.
Abstract: This study was aimed to study the probability about
the production of fiberboard made of durian rind through latex with
phenolic resin as binding agent. The durian rind underwent the
boiling process with NaOH [7], [8] and then the fiber from durian
rind was formed into fiberboard through heat press. This means that
durian rind could be used as replacement for plywood in plywood
industry by using durian fiber as composite material with adhesive
substance. This research would study the probability about the
production of fiberboard made of durian rind through latex with
phenolic resin as binding agent. At first, durian rind was split,
exposed to light, boiled and steamed in order to gain durian fiber.
Then, fiberboard was tested with the density of 600 Kg/m3 and 800
Kg/m3. in order to find a suitable ratio of durian fiber and latex.
Afterwards, mechanical properties were tested according to the
standards of ASTM and JIS A5905-1994. After the suitable ratio was
known, the test results would be compared with medium density
fiberboard (MDF) and other related research studies. According to
the results, fiberboard made of durian rind through latex with
phenolic resin at the density of 800 Kg/m3 at ratio of 1:1, the
moisture was measured to be 5.05% with specific gravity (ASTM D
2395-07a) of 0.81, density (JIS A 5905-1994) of 0.88 g/m3, tensile
strength, hardness (ASTM D2240), flexibility or elongation at break
yielded similar values as the ones by medium density fiberboard
(MDF).
Abstract: Carbon fibers have specific characteristics in
comparison with industrial and structural materials used in different
applications. Special properties of carbon fibers make them attractive
for reinforcing and fabrication of composites. These fibers have been
utilized for composites of metals, ceramics and plastics. However,
it-s mainly used in different forms to reinforce lightweight polymer
materials such as epoxy resin, polyesters or polyamides. The
composites of carbon fiber are stronger than steel, stiffer than
titanium, and lighter than aluminum and nowadays they are used in a
variety of applications. This study explains applications of carbon
fibers in different fields such as space, aviation, transportation,
medical, construction, energy, sporting goods, electronics, and the
other commercial/industrial applications. The last findings of
composites with polymer, metal and ceramic matrices containing
carbon fibers and their applications in the world investigated.
Researches show that carbon fibers-reinforced composites due to
unique properties (including high specific strength and specific
modulus, low thermal expansion coefficient, high fatigue strength,
and high thermal stability) can be replaced with common industrial
and structural materials.
Abstract: Nowadays due to globalization of economy and
competition environment, innovation and technology plays key role
at creation of wealth and economic growth of countries. In fact
prompt growth of practical and technologic knowledge may results in
social benefits for countries when changes into effective innovation.
Considering the importance of innovation for the development of
countries, this study addresses the radical technological innovation
introduced by nanopapers at different stages of producing paper
including stock preparation, using authorized additives, fillers and
pigments, using retention, calender, stages of producing conductive
paper, porous nanopaper and Layer by layer self-assembly. Research
results show that in coming years the jungle related products will lose
considerable portion of their market share, unless embracing radical
innovation. Although incremental innovations can make this industry
still competitive in mid-term, but to have economic growth and
competitive advantage in long term, radical innovations are
necessary. Radical innovations can lead to new products and
materials which their applications in packaging industry can produce
value added. However application of nanotechnology in this industry
can be costly, it can be done in cooperation with other industries to
make the maximum use of nanotechnology possible. Therefore this
technology can be used in all the production process resulting in the
mass production of simple and flexible papers with low cost and
special properties such as facility at shape, form, easy transportation,
light weight, recovery and recycle marketing abilities, and sealing.
Improving the resistance of the packaging materials without reducing
the performance of packaging materials enhances the quality and the
value added of packaging. Improving the cellulose at nano scale can
have considerable electron optical and magnetic effects leading to
improvement in packaging and value added. Comparing to the
specifications of thermoplastic products and ordinary papers,
nanopapers show much better performance in terms of effective
mechanical indexes such as the modulus of elasticity, tensile strength,
and strain-stress. In densities lower than 640 kgm -3, due to the
network structure of nanofibers and the balanced and randomized
distribution of NFC in flat space, these specifications will even
improve more. For nanopapers, strains are 1,4Gpa, 84Mpa and 17%,
13,3 Gpa, 214Mpa and 10% respectively. In layer by layer self
assembly method (LbL) the tensile strength of nanopaper with Tio3
particles and Sio2 and halloysite clay nanotube are 30,4 ±7.6Nm/g
and 13,6 ±0.8Nm/g and 14±0.3,3Nm/g respectively that fall within
acceptable range of similar samples with virgin fiber. The usage of
improved brightness and porosity index in nanopapers can create
more competitive advantages at packaging industry.
Abstract: Wavelength multiplexing (WDM) technology along
with optical amplifiers is used for optical communication systems in
S-band, C-band and L-band. To improve the overall system
performance Hybrid amplifiers consisting of cascaded TDFA and
EDFA with different gain bandwidths are preferred for long haul
wavelength multiplexed optical communication systems. This paper
deals with statistical analysis of different configuration of hybrid
amplifier i.e. analysis of TDFA-EDFA configuration and EDFA –
TDFA configuration. In this paper One-Way ANOVA method is used
for statistical analysis.
Abstract: This study deals with a multi-criteria optimization
problem which has been transformed into a single objective
optimization problem using Response Surface Methodology (RSM),
Artificial Neural Network (ANN) and Grey Relational Analyses
(GRA) approach. Grey-RSM and Grey-ANN are hybrid techniques
which can be used for solving multi-criteria optimization problem.
There have been two main purposes of this research as follows.
1. To determine optimum and robust fiber dyeing process
conditions by using RSM and ANN based on GRA,
2. To obtain the best suitable model by comparing models
developed by different methodologies.
The design variables for fiber dyeing process in textile are
temperature, time, softener, anti-static, material quantity, pH,
retarder, and dispergator. The quality characteristics to be evaluated
are nominal color consistency of fiber, maximum strength of fiber,
minimum color of dyeing solution. GRA-RSM with exact level
value, GRA-RSM with interval level value and GRA-ANN models
were compared based on GRA output value and MSE (Mean Square
Error) performance measurement of outputs with each other. As a
result, GRA-ANN with interval value model seems to be suitable
reducing the variation of dyeing process for GRA output value of the
model.
Abstract: It has been proven that early establishment of
microbial flora in digestive tract of ruminants, has a beneficial effect
on their health condition and productivity. A probiotic compound,
made from five bacteria isolated from adult bovine cattle, was dosed
to 15 Holstein newborn calves in order to measure its capacity of
improving body weight gain and reduce diarrhea incidence. The test
was performed in the municipality of Cajicá (Colombia), at 2580
m.a.s.l., throughout rainy season, with environmental temperature
that oscillated between 4 to 25 °C. Five calves were allotted to
control (no addition of probiotic). Treatments 1, and 2 (5 calves per
group) received 10 ml Probiotic mix 1 and 2, respectively. Probiotic
mixes 1 and 2 where similar in microbial composition but different in
production process. Probiotics were added to the morning milk and
dosed on a daily basis by a month and then on a weekly basis for
three additional months. Diarrhea incidence was measured by
observance of number of animals affected in each group; each animal
was weighed up on a daily basis for obtaining weight gain and rumen
fluid samples were extracted with oro-esophageal catheter for
determining level of fiber and grain consumption.
Abstract: A two-parameter fatigue model explicitly accounting for the cyclic as well as the mean stress was used to fit static and fatigue data available in literature concerning carbon fiber reinforced composite laminates subjected tension-tension fatigue. The model confirms the strength–life equal rank assumption and predicts reasonably the probability of failure under cyclic loading. The model parameters were found by best fitting procedures and required a minimum of experimental tests.
Abstract: The objective of this work was to investigate flow
properties of powdered infant formula samples. Samples were
purchased at a local pharmacy and differed in composition. Lactose
free infant formula, gluten free infant formula and infant formulas
containing dietary fibers and probiotics were tested and compared
with a regular infant formula sample which did not contain any of
these supplements. Particle size and bulk density were determined
and their influence on flow properties was discussed. There were no
significant differences in bulk densities of the samples, therefore the
connection between flow properties and bulk density could not be
determined. Lactose free infant formula showed flow properties
different to standard supplement-free sample. Gluten free infant
formula with addition of probiotic microorganisms and dietary fiber
had the narrowest particle size distribution range and exhibited the
best flow properties. All the other samples exhibited the same
tendency of decreasing compaction coefficient with increasing flow
speed, which means they all become freer flowing with higher flow
speeds.
Abstract: This paper presents the Literature Review of carbon fiber reinforced polymer (CFRP) strips to reinforced concrete (RC) as a strengthening solution for T-beams. Although a great deal of research has been carried out on Rectangular beams strengthened with Fibre-Reinforced Polymer composites (FRP), Fiber reinforced polymer (FRP) composites have been increasingly studied for their application in the flexural or shear strengthening of reinforced concrete (RC) members. A detailed discussion of the shearstrengthening repair with FRP is undertaken. This paper will be limited to research of CFRP material externally bonded to the tensile face of concrete beams. In particular, research studying the effect of externally applied CFRP materials on the shear performance of reinforced concrete beams will be reported.
Abstract: Gilaburu (Viburnum opulus L.) grown naturally in
Anatolia. In this study, some physico-chemical (sugar, acid, protein,
crude fat, crude fiber, ash etc.) characteristics and mineral
composition of Gilaburu fruit have been investigated. The length,
width, thickness, weight, total soluble solid, protein, crude ash, crude
fiber and crude oil of fruit were found to be 1.12 cm, 1.58 cm, 1.87
cm, 0.87 g, 14.73 %, 0.2 %, 0.11 %, 6.56 % and 0.4 %, respectively.
The seed of fruit mean weight, length, width and thickness were
determinated as 0.08 g, 7.76 cm, 7.67 cm and 1.66, respectively. In
addition 27 mineral elements (Al, Mg, Na, Ba, Ca, Ni, Cd, P, Cr, Pb,
S, Cu, Se, Fe, K, Sr, Li, Z, V, Ag, Bi, Co, Mn, B, Ga, In, Ti) were
analyzed. Gilaburu (Viburnum opulus L.) fruit was richest in
potassium (10764.764 ppm), Mg (1289.088 ppm) and P (1304.169
ppm).
Abstract: Composite laminates are relatively weak in out of
plane loading, inter-laminar stress, stress concentration near the edge
and stress singularities. This paper develops a new analytical
formulation for laminated composite rotating disc fabricated from
symmetric sequential quasi isotropic layers to predict three
dimensional stress and deformation. This analysis is necessary to
evaluate mechanical integrity of fiber reinforced multi-layer
laminates used for high speed rotating applications such as high
speed impellers. Three dimensional governing equations are written
for rotating composite disc. Explicit solution is obtained with
"Frobenius" expansion series. Based on analytical results, there are
two separate zones of three dimensional stress fields in centre and
edge of rotating disc. For thin discs, out of plane deformations and
stresses are small in comparison with plane ones. For relatively thick
discs deformation and stress fields are three dimensional.
Abstract: In this paper, an analytical approach is used to study the coupled lateral-torsional vibrations of laminated composite beam. It is known that in such structures due to the fibers orientation in various layers, any lateral displacement will produce a twisting moment. This phenomenon is modeled by the bending-twisting material coupling rigidity and its main feature is the coupling of lateral and torsional vibrations. In addition to the material coupling, the effects of shear deformation and rotary inertia are taken into account in the definition of the potential and kinetic energies. Then, the governing differential equations are derived using the Hamilton-s principle and the mathematical model matches the Timoshenko beam model when neglecting the effect of bending-twisting rigidity. The equations of motion which form a system of three coupled PDEs are solved analytically to study the free vibrations of the beam in lateral and rotational modes due to the bending, as well as the torsional mode caused by twisting. The analytic solution is carried out in three steps: 1) assuming synchronous motion for the kinematic variables which are the lateral, rotational and torsional displacements, 2) solving the ensuing eigenvalue problem which contains three coupled second order ODEs and 3) imposing different boundary conditions related to combinations of simply, clamped and free end conditions. The resulting natural frequencies and mode shapes are compared with similar results in the literature and good agreement is achieved.
Abstract: A simple microstructure optical fiber design based on an octagonal cladding structure is presented for simultaneously controlling dispersion and leakage properties. The finite difference method with anisotropic perfectly matched boundary layer is used to investigate the guiding properties. It is demonstrated that octagonal photonic crystal fibers with four rings can assume negative ultra-flattened dispersion of -19 + 0.23 ps/nm/km in the wavelength range of 1.275 μm to 1.68 μm, nearly zero ultra-flattened dispersion of 0 ± 0.40 ps/nm/km in a 1.38 to 1.64 μm, and low confinement losses less than 10-3 dB/km in the entire band of interest.
Abstract: In order to supplement the brittle property of concrete,
fibers are added into concrete mixtures. Compared to general concrete,
various characteristics such as tensile strength, bending strength,
bending toughness, and resistance to crack are superior, and even
when cracks occur, improvements on toughness as well as resistance
to shock are excellent due to the growth of fracture energy. Increased
function of steel fiber reinforced concrete can be differentiated
depending on the fiber dispersion, and sand percentage can be an
important influence on the fiber dispersion. Therefore, in this research,
experiments were planned on sand percentage in order to apprehend
the influence of sand percentage on the bending properties and direct
tension of SFRC and basic experiments were conducted on bending
and direct tension in order to recognize the properties of bending
properties and direct tension following the size of the aggregates and
sand percentage.
Abstract: In this study four Holstein steers with rumen fistula
fed 7 kg of dry matter (DM) of diets differing in concentrate to
alfalfa hay ratios as 60:40, 70:30, 80:20, and 90:10 in a 4 × 4 latin
square design. The pH of the ruminal fluid was measured before
the morning feeding (0.0 h) to 8 h post feeding. In this study, a
two-layered feed-forward neural network trained by the
Levenberg-Marquardt algorithm was used for modelling of ruminal
pH. The input variables of the network were time, concentrate to
alfalfa hay ratios (C/F), non fiber carbohydrate (NFC) and neutral
detergent fiber (NDF). The output variable was the ruminal pH.
The modeling results showed that there was excellent agreement
between the experimental data and predicted values, with a high
determination coefficient (R2 >0.96). Therefore, we suggest using
these model-derived biological values to summarize continuously
recorded pH data.
Abstract: An inflation–extension test with human vena cava
inferior was performed with the aim to fit a material model. The vein
was modeled as a thick–walled tube loaded by internal pressure and
axial force. The material was assumed to be an incompressible
hyperelastic fiber reinforced continuum. Fibers are supposed to be
arranged in two families of anti–symmetric helices. Considered
anisotropy corresponds to local orthotropy. Used strain energy
density function was based on a concept of limiting strain
extensibility. The pressurization was comprised by four pre–cycles
under physiological venous loading (0 – 4kPa) and four cycles under
nonphysiological loading (0 – 21kPa). Each overloading cycle was
performed with different value of axial weight. Overloading data
were used in regression analysis to fit material model. Considered
model did not fit experimental data so good. Especially predictions
of axial force failed. It was hypothesized that due to
nonphysiological values of loading pressure and different values of
axial weight the material was not preconditioned enough and some
damage occurred inside the wall. A limiting fiber extensibility
parameter Jm was assumed to be in relation to supposed damage.
Each of overloading cycles was fitted separately with different values
of Jm. Other parameters were held the same. This approach turned out
to be successful. Variable value of Jm can describe changes in the
axial force – axial stretch response and satisfy pressure – radius
dependence simultaneously.