Abstract: The previous study of new metal gasket that contact
width and contact stress an important design parameter for optimizing
metal gasket performance. The optimum design based on an elastic
and plastic contact stress was founded. However, the influence of
flange surface roughness had not been investigated thoroughly. The
flange has many kinds of surface roughness. In this study, we
conducted a gasket model include a flange surface roughness effect. A
finite element method was employed to develop simulation solution. A
uniform quadratic mesh used for meshing the gasket material and a
gradually quadrilateral mesh used for meshing the flange. The gasket
model was simulated by using two simulation stages which is forming
and tightening simulation. A simulation result shows that a smoother
of surface roughness has higher slope for force per unit length. This
mean a squeezed against between flange and gasket will be strong. The
slope of force per unit length for gasket 400-MPa mode was higher
than the gasket 0-MPa mode.
Abstract: In a nuclear reactor Loss of Coolant accident (LOCA)
considers wide range of postulated damage or rupture of pipe in the
heat transport piping system. In the case of LOCA with/without
failure of emergency core cooling system in a Pressurised Heavy
water Reactor, the Pressure Tube (PT) temperature could rise
significantly due to fuel heat up and gross mismatch of the heat
generation and heat removal in the affected channel. The extent and
nature of deformation is important from reactor safety point of view.
Experimental set-ups have been designed and fabricated to simulate
ballooning (radial deformation) of PT for 220 MWe IPHWRs.
Experiments have been conducted by covering the CT by ceramic
fibers and then by submerging CT in water of voided PTs. In both
the experiments, it is observed that ballooning initiates at a
temperature around 665´┐¢C and complete contact between PT and
Caldaria Tube (CT) occurs at around 700´┐¢C approximately. The
strain rate is found to be 0.116% per second. The structural integrity
of PT is retained (no breach) for all the experiments. The PT heatup
is found to be arrested after the contact between PT and CT, thus
establishing moderator acting as an efficient heat sink for IPHWRs.
Abstract: This study reports the implementation of Good
Manufacturing Practice (GMP) in a polycarbonate film processing
plant. The implementation of GMP took place with the creation of a
multidisciplinary team. It was carried out in four steps: conduct gap
assessment, create gap closure plan, close gaps, and follow up the
GMP implementation. The basis for the gap assessment is the
guideline for GMP for plastic materials and articles intended for Food
Contact Material (FCM), which was edited by Plastic Europe. The
effective results of the GMP implementation in this study showed
100% completion of gap assessment. The key success factors for
implementing GMP in production process are the commitment,
intention and support of top management.
Abstract: The dynamical contouring error is a critical element for the accuracy of machine tools. The contouring error is defined as the difference between the processing actual path and commanded path, which is implemented by following the command curves from feeding driving system in machine tools. The contouring error is resulted from various factors, such as the external loads, friction, inertia moment, feed rate, speed control, servo control, and etc. Thus, the study proposes a 2D compensating system for the contouring accuracy of machine tools. Optical method is adopted by using stable frequency laser diode and the high precision position sensor detector (PSD) to performno-contact measurement. Results show the related accuracy of position sensor detector (PSD) of 2D contouring accuracy compensating system was ±1.5 μm for a calculated range of ±3 mm, and improvement accuracy is over 80% at high-speed feed rate.
Abstract: Electrical distribution systems are incurring large losses as the loads are wide spread, inadequate reactive power compensation facilities and their improper control. A comprehensive static VAR compensator consisting of capacitor bank in five binary sequential steps in conjunction with a thyristor controlled reactor of smallest step size is employed in the investigative work. The work deals with the performance evaluation through analytical studies and practical implementation on an existing system. A fast acting error adaptive controller is developed suitable both for contactor and thyristor switched capacitors. The switching operations achieved are transient free, practically no need to provide inrush current limiting reactors, TCR size minimum providing small percentages of nontriplen harmonics, facilitates stepless variation of reactive power depending on load requirement so as maintain power factor near unity always. It is elegant, closed loop microcontroller system having the features of self regulation in adaptive mode for automatic adjustment. It is successfully tested on a distribution transformer of three phase 50 Hz, Dy11, 11KV/440V, 125 KVA capacity and the functional feasibility and technical soundness are established. The controller developed is new, adaptable to both LT & HT systems and practically established to be giving reliable performance.
Abstract: The electrical and structural properties of Hf/Al/Ni/Au
(20/100/25/50 nm) ohmic contact to n-GaN are reported in this study.
Specific contact resistivities of Hf/Al/Ni/Au based contacts have been
investigated as a function of annealing temperature and achieve the
lowest value of 1.09´10-6 Ω·cm2 after annealing at 650 oC in vacuum.
A detailed mechanism of ohmic contact formation is discussed. By
using different chemical analyses, it is anticipated that the formation of
Hf-Al-N alloy might be responsible to form low temperature ohmic
contacts for the Hf-based scheme to n-GaN.
Abstract: One of the main research directions in CAD/CAM
machining area is the reducing of machining time.
The feedrate scheduling is one of the advanced techniques that
allows keeping constant the uncut chip area and as sequel to keep
constant the main cutting force. They are two main ways for feedrate
optimization. The first consists in the cutting force monitoring, which
presumes to use complex equipment for the force measurement and
after this, to set the feedrate regarding the cutting force variation. The
second way is to optimize the feedrate by keeping constant the
material removal rate regarding the cutting conditions.
In this paper there is proposed a new approach using an extended
database that replaces the system model.
The feedrate scheduling is determined based on the identification
of the reconfigurable machine tool, and the feed value determination
regarding the uncut chip section area, the contact length between tool
and blank and also regarding the geometrical roughness.
The first stage consists in the blank and tool monitoring for the
determination of actual profiles. The next stage is the determination
of programmed tool path that allows obtaining the piece target
profile.
The graphic representation environment models the tool and blank
regions and, after this, the tool model is positioned regarding the
blank model according to the programmed tool path. For each of
these positions the geometrical roughness value, the uncut chip area
and the contact length between tool and blank are calculated. Each of
these parameters are compared with the admissible values and
according to the result the feed value is established.
We can consider that this approach has the following advantages:
in case of complex cutting processes the prediction of cutting force is
possible; there is considered the real cutting profile which has
deviations from the theoretical profile; the blank-tool contact length
limitation is possible; it is possible to correct the programmed tool
path so that the target profile can be obtained.
Applying this method, there are obtained data sets which allow the
feedrate scheduling so that the uncut chip area is constant and, as a
result, the cutting force is constant, which allows to use more
efficiently the machine tool and to obtain the reduction of machining
time.
Abstract: In this paper a three dimensional thermal model of a
sliding contact system is proposed for both steady-state or transient
conditions. The influence of contact force, electric current and
ambient temperature on the temperature distribution, has been
investigated. A thermal analysis of the different type of the graphite
material of fixed electric contact and its influence on contact system
temperature rise, has been performed. To validate the three
dimensional thermal model, some experimental tests have been done.
There is a good correlation between experimental and simulation
results.
Abstract: Two different superhydrophobic surfaces were
elaborated and their oil repellency behavior was evaluated using
several liquid with different surface tension. A silicone rubber/SiO2
nanocomposite coated (A) on aluminum substrate by “spin-coating"
and the sample B was an anodized aluminum surface covered by
Teflon-like coating. A high static contact angle about ∼162° was
measured for two prepared surfaces on which the water droplet rolloff.
Scanning electron microscopy (SEM) showed the presence of
micro/nanostructures for both sample A and B similar to that of lotus
leaf.
However the sample A presented significantly different behaviour
of wettability against the low surface tension liquid. Sample A has
been wetted totally by oil (dodecan) droplet while sample B showed
oleophobic behaviour. Oleophobic property of Teflon like coating
can be contributed to the presence of CF2 and CF3 functional group
which was shown by XPS analysis.
Abstract: An original Direct Numerical Simulation (DNS) method to tackle the problem of particulate flows at moderate to high concentration and finite Reynolds number is presented. Our method is built on the framework established by Glowinski and his coworkers [1] in the sense that we use their Distributed Lagrange Multiplier/Fictitious Domain (DLM/FD) formulation and their operator-splitting idea but differs in the treatment of particle collisions. The novelty of our contribution relies on replacing the simple artificial repulsive force based collision model usually employed in the literature by an efficient Discrete Element Method (DEM) granular solver. The use of our DEM solver enables us to consider particles of arbitrary shape (at least convex) and to account for actual contacts, in the sense that particles actually touch each other, in contrast with the simple repulsive force based collision model. We recently upgraded our serial code, GRIFF 1 [2], to full MPI capabilities. Our new code, PeliGRIFF 2, is developed under the framework of the full MPI open source platform PELICANS [3]. The new MPI capabilities of PeliGRIFF open new perspectives in the study of particulate flows and significantly increase the number of particles that can be considered in a full DNS approach: O(100000) in 2D and O(10000) in 3D. Results on the 2D/3D sedimentation/fluidization of isometric polygonal/polyedral particles with collisions are presented.
Abstract: Wetting characteristics of reactive (Sn–0.7Cu solder)
and non– reactive (castor oil) wetting of liquids on Cu and Ag plated
Al substrates have been investigated. Solder spreading exhibited
capillary, gravity and viscous regimes. Oils did not exhibit noticeable
spreading regimes. Solder alloy showed better wettability on Ag
coated Al substrate compared to Cu plating. In the case of castor oil,
Cu coated Al substrate exhibited good wettability as compared to Ag
coated Al substrates. The difference in wettability during reactive
wetting of solder and non–reactive wetting of oils is attributed to the
change in the surface energies of Al substrates brought about by the
formation of intermetallic compounds (IMCs).
Abstract: In the numerical solution of the forward dynamics of a
multibody system, the positions and velocities of the bodies in the
system are obtained first. With the information of the system state
variables at each time step, the internal and external forces acting on
the system are obtained by appropriate contact force models if the
continuous contact method is used instead of a discrete contact
method. The local deformation of the bodies in contact, represented
by penetration, is used to compute the contact force. The ability and
suitability with current cylindrical contact force models to describe
the contact between bodies with cylindrical geometries with
particular focus on internal contacting geometries involving low
clearances and high loads simultaneously is discussed in this paper.
A comparative assessment of the performance of each model under
analysis for different contact conditions, in particular for very
different penetration and clearance values, is presented. It is
demonstrated that some models represent a rough approximation to
describe the conformal contact between cylindrical geometries
because contact forces are underestimated.
Abstract: This paper describes a three-dimensional thermal
model of the current path included in the low voltage power circuit
breakers. The model can be used to analyse the thermal behaviour of
the current path during both steady-state and transient conditions.
The current path lengthwise temperature distribution and timecurrent
characteristic of the terminal connections of the power circuit
breaker have been obtained. The influence of the electric current and
voltage drop on main electric contact of the circuit breaker has been
investigated. To validate the three-dimensional thermal model, some
experimental tests have been done. There is a good correlation
between experimental and simulation results.
Abstract: Delay-Tolerant Networks (DTNs) are sparse, wireless
networks where disconnections are common due to host mobility and
low node density. The Message Ferrying (MF) scheme is a mobilityassisted
paradigm to improve connectivity in DTN-like networks. A
ferry or message ferry is a special node in the network which has
a per-determined route in the deployed area and relays messages
between mobile hosts (MHs) which are intermittently connected.
Increased contact opportunities among mobile hosts and the ferry
improve the performance of the network, both in terms of message
delivery ratio and average end-end delay. However, due to the inherent
mobility of mobile hosts and pre-determined periodicity of the
message ferry, mobile hosts may often -miss- contact opportunities
with a ferry. In this paper, we propose the combination of stationary
ferry access points (FAPs) with MF routing to increase contact
opportunities between mobile hosts and the MF and consequently
improve the performance of the DTN. We also propose several
placement models for deploying FAPs on MF routes. We evaluate the
performance of the FAP placement models through comprehensive
simulation. Our findings show that FAPs do improve the performance
of MF-assisted DTNs and symmetric placement of FAPs outperforms
other placement strategies.
Abstract: The objective of this research is to study the people’s level of participation in activities of the community, their satisfaction towards the community, the attachment they have to the community, factors that influence the attachment, as well as the characteristics of the relationships of military families’ of the Royal Guards community of Dusit District. The method used was non-probability sampling by quota sampling according to people’s age. The determined age group was 18 years or older.
One set of a sample group was done per family. The questionnaires were conducted by 287 people. Snowball sampling was also used by interviewing people of the community, starting from the Royal Guards Community’s leader, then by 20 of the community’s well-respected persons. The data was analyzed by using descriptive statistics, such as arithmetic mean and standard deviation, as well as by inferential statistics, such as Independent - Samples T test (T-test), One-Way ANOVA (F-test), Chi-Square. Descriptive analysis according to the structure of the interview content was also used. The results of the research is that the participation of the population in the Royal Guards Community in various activities is at a medium level, with the average participation level during Mother’s and Father’s Days. The people’s general level of satisfaction towards the premises of the Royal Guards Community is at the highest level.
The people were most satisfied with the transportation within the community and in contacting with people from outside the premises. The access to the community is convenient and there are various entrances. The attachment of the people to the Royal Guards Community in general and by each category is at a high level. The feeling that the community is their home rated the highest average. Factors that influence the attachment of the people of the Royal Guards Community are age, status, profession, income, length of stay in the community, membership of social groups, having neighbors they feel close and familiar with, and as well as the benefits they receive from the community. In addition, it was found that people that participate in activities have a high level of positive relationship towards the attachment of the people to the Royal Guards Community. The satisfaction of the community has a very high level of positive relationship with the attachment of the people to the Royal Guards Community.
The characteristics of the attachment of military families’ is that they live in big houses that everyone has to protect and care for, starting from the leader of the family as well as all members. Therefore, they all love the community they live in. The characteristics that show the participation of activities within the community and the high level of satisfaction towards the premises of the community will enable the people to be more attached to the community. The people feel that everyone is close neighbors within the community, as if they are one big family.
Abstract: Pabdeh shaly formation (Paleocene-Oligomiocene)
has been expanded in Fars, Khozestan and Lorestan. The lower
lithostratigraphic limit of this formation in Shiraz area is
distinguished from Gurpi formation by purple shale. Its upper limit is
gradational and conformable with Asmari formation. In order to
study sequence stratigraphy and microfacies of Pabdeh formation in
Shiraz area, one stratigraphic section have been chosen (Zanjiran
section). Petrographic studies resulted in the identification of 9
pelagic and calciturbidite microfacies. The calciturbidite microfacies
have been formed when the sea level was high, the rate of carbonate
deposition was high and it slumped into the deep marine. Sequence
stratigraphy studies show that Pabdeh formation in the studied zone
consists of two depositional sequences (DS) that the lower contact is
erosional (purple shale - type one, SBI or type two, SB2) and the
upper contact is correlative conformity (type two, SB2).
Abstract: The objective of this paper is to study the electrical
resistivity complexity between field and laboratory measurement, in
order to improve the effectiveness of data interpretation for
geophysical ground resistivity survey. The geological outcrop in
Penang, Malaysia with an obvious layering contact was chosen as the
study site. Two dimensional geoelectrical resistivity imaging were
used in this study to maps the resistivity distribution of subsurface,
whereas few subsurface sample were obtained for laboratory
advance. In this study, resistivity of samples in original conditions is
measured in laboratory by using time domain low-voltage technique,
particularly for granite core sample and soil resistivity measuring set
for soil sample. The experimentation results from both schemes are
studied, analyzed, calibrated and verified, including basis and
correlation, degree of tolerance and characteristics of substance.
Consequently, the significant different between both schemes is
explained comprehensively within this paper.
Abstract: Blood pulse is an important human physiological signal commonly used for the understanding of the individual physical health. Current methods of non-invasive blood pulse sensing require direct contact or access to the human skin. As such, the performances of these devices tend to vary with time and are subjective to human body fluids (e.g. blood, perspiration and skin-oil) and environmental contaminants (e.g. mud, water, etc). This paper proposes a simulation model for the novel method of non-invasive acquisition of blood pulse using the disturbance created by blood flowing through a localized magnetic field. The simulation model geometry represents a blood vessel, a permanent magnet, a magnetic sensor, surrounding tissues and air in 2-dimensional. In this model, the velocity and pressure fields in the blood stream are described based on Navier-Stroke equations and the walls of the blood vessel are assumed to have no-slip condition. The blood assumes a parabolic profile considering a laminar flow for blood in major artery near the skin. And the inlet velocity follows a sinusoidal equation. This will allow the computational software to compute the interactions between the magnetic vector potential generated by the permanent magnet and the magnetic nanoparticles in the blood. These interactions are simulated based on Maxwell equations at the location where the magnetic sensor is placed. The simulated magnetic field at the sensor location is found to assume similar sinusoidal waveform characteristics as the inlet velocity of the blood. The amplitude of the simulated waveforms at the sensor location are compared with physical measurements on human subjects and found to be highly correlated.
Abstract: This paper presents the Function Approximation
Technique (FAT) based adaptive impedance control for a robotic
finger. The force based impedance control is developed so that the
robotic finger tracks the desired force while following the reference
position trajectory, under unknown environment position and
uncertainties in finger parameters. The control strategy is divided into
two phases, which are the free and contact phases. Force error
feedback is utilized in updating the uncertain environment position
during contact phase. Computer simulations results are presented to
demonstrate the effectiveness of the proposed technique.
Abstract: Removal of a reactive dye (Reactive blue 4) by
adsorption utilizing waste aluminium hydroxide sludge as an
adsorbent was investigated. The removal of the dye was optimized
using response surface methodology (RSM). In the RSM
experiments; initial dye concentration, adsorbent concentration and
contact time were critical parameters. RSM experiments were
performed at the range of initial dye concentration 31.82-368.18
mg/L, adsorbent concentration 3.18-36.82 g/L, contact time 15.82-
56.18 h. Optimum initial dye concentration, adsorbent concentration
and contact time were obtained as 108.83 mg/L, 29.36 g/L and 33.57
h respectively. At these conditions, maximum removal of the dye was
obtained as 95%. The experiments were performed at the optimum
conditions to verify these results and the same results were obtained.