Abstract: We study the dynamic response of a wind turbine
structure subjected to theoretical seismic motions, taking into account
the rotational component of ground shaking. Models are generated
for a shallow moderate crustal earthquake in the Madrid Region
(Spain). Synthetic translational and rotational time histories are
computed using the Discrete Wavenumber Method, assuming a point
source and a horizontal layered earth structure. These are used to
analyze the dynamic response of a wind turbine, represented by a
simple finite element model. Von Mises stress values at different
heights of the tower are used to study the dynamical structural
response to a set of synthetic ground motion time histories
Abstract: Beta-spline is built on G2 continuity which guarantees
smoothness of generated curves and surfaces using it. This curve is
preferred to be used in object design rather than reconstruction. This
study however, employs the Beta-spline in reconstructing a 3-
dimensional G2 image of the Stanford Rabbit. The original data
consists of multi-slice binary images of the rabbit. The result is then
compared with related works using other techniques.
Abstract: This paper aims to propose a novel, robust, and simple method for obtaining a human 3D face model and camera pose (position and orientation) from a video sequence. Given a video sequence of a face recorded from an off-the-shelf digital camera, feature points used to define facial parts are tracked using the Active- Appearance Model (AAM). Then, the face-s 3D structure and camera pose of each video frame can be simultaneously calculated from the obtained point correspondences. This proposed method is primarily based on the combined approaches of Gradient Descent and Powell-s Multidimensional Minimization. Using this proposed method, temporarily occluded point including the case of self-occlusion does not pose a problem. As long as the point correspondences displayed in the video sequence have enough parallax, these missing points can still be reconstructed.
Abstract: The theatre-auditorium under investigation following
the highly reflective characteristics of materials used in it (marble,
painted wood, smooth plaster, etc), architectural and structural
features of the Protocol and its intended use (very multifunctional:
Auditorium, theatre, cinema, musicals, conference room) from the
analysis of the statement of fact made by the acoustic simulation
software Ramsete and supported by data obtained through a
campaign of acoustic measurements of the state of fact made on the
spot by a Fonomet Svantek model SVAN 957, appears to be
acoustically inadequate. After the completion of the 3D model
according to the specifications necessary software used forecast in
order to be recognized by him, have made three simulations, acoustic
simulation of the state of and acoustic simulation of two design
solutions.
Improved noise characteristics found in the first design solution,
compared to the state in fact consists therefore in lowering
Reverberation Time that you turn most desirable value, while the
Indicators of Clarity, the Baricentric Time, the Lateral Efficiency,
Ratio of Low Tmedia BR and defined the Speech Intelligibility
improved significantly. Improved noise characteristics found instead
in the second design solution, as compared to first design solution, is
finally mostly in a more uniform distribution of Leq and in lowering
Reverberation Time that you turn the optimum values. Indicators of
Clarity, and the Lateral Efficiency improve further but at the expense
of a value slightly worse than the BR. Slightly vary the remaining
indices.
Abstract: Manufacturing Industries face a crucial change as products and processes are required to, easily and efficiently, be reconfigurable and reusable. In order to stay competitive and flexible, situations also demand distribution of enterprises globally, which requires implementation of efficient communication strategies. A prototype system called the “Broadcaster" has been developed with an assumption that the control environment description has been engineered using the Component-based system paradigm. This prototype distributes information to a number of globally distributed partners via an adoption of the circular-based data processing mechanism. The work highlighted in this paper includes the implementation of this mechanism in the domain of the manufacturing industry. The proposed solution enables real-time remote propagation of machine information to a number of distributed supply chain client resources such as a HMI, VRML-based 3D views and remote client instances regardless of their distribution nature and/ or their mechanisms. This approach is presented together with a set of evaluation results. Authors- main concentration surrounds the reliability and the performance metric of the adopted approach. Performance evaluation is carried out in terms of the response times taken to process the data in this domain and compared with an alternative data processing implementation such as the linear queue mechanism. Based on the evaluation results obtained, authors justify the benefits achieved from this proposed implementation and highlight any further research work that is to be carried out.
Abstract: As a result of the daily workflow in the design
development departments of companies, databases containing huge
numbers of 3D geometric models are generated. According to the
given problem engineers create CAD drawings based on their design
ideas and evaluate the performance of the resulting design, e.g. by
computational simulations. Usually, new geometries are built either
by utilizing and modifying sets of existing components or by adding
single newly designed parts to a more complex design.
The present paper addresses the two facets of acquiring
components from large design databases automatically and providing
a reasonable overview of the parts to the engineer. A unified
framework based on the topographic non-negative matrix
factorization (TNMF) is proposed which solves both aspects
simultaneously. First, on a given database meaningful components
are extracted into a parts-based representation in an unsupervised
manner. Second, the extracted components are organized and
visualized on square-lattice 2D maps. It is shown on the example of
turbine-like geometries that these maps efficiently provide a wellstructured
overview on the database content and, at the same time,
define a measure for spatial similarity allowing an easy access and
reuse of components in the process of design development.
Abstract: Monitored 3-Dimensional (3D) video experience can be utilized as “feedback information” to fine tune the service parameters for providing a better service to the demanding 3D service customers. The 3D video experience which includes both video quality and depth perception is influenced by several contextual and content related factors (e.g., ambient illumination condition, content characteristics, etc) due to the complex nature of the 3D video. Therefore, effective factors on this experience should be utilized while assessing it. In this paper, structural information of the depth map sequences of the 3D video is considered as content related factor effective on the depth perception assessment. Cartoon-like filter is utilized to abstract the significant depth levels in the depth map sequences to determine the structural information. Moreover, subjective experiments are conducted using 3D videos associated with cartoon-like depth map sequences to investigate the effectiveness of ambient illumination condition, which is a contextual factor, on depth perception. Using the knowledge gained through this study, 3D video experience metrics can be developed to deliver better service to the 3D video service users.
Abstract: Channel junctions can be analyzed in two ways of
division (lateral intake) and combined flows (confluence). The
present paper investigates 3D flow pattern at lateral intake using
Navier-Stokes equation and κ -ε (RNG) turbulent model. The
equations are solved by Finite-Volume Method (FVM) and results
are compared with the experimental data of (Barkdoll, B.D., 1997)
to test the validity of the findings. Comparison of the results with
the experimental data indicated a close proximity between the two
sets of data which suggest a very close simulation. Results further
indicated an inverse relation between the effects of discharge ratio
( r Q ) on the length and width of the separation zone. In other words,
as the discharge ration increases, the length and width of separation
zone decreases.
Abstract: This paper presents a novel method for prediction of
the mechanical behavior of proximal femur using the general
framework of the quantitative computed tomography (QCT)-based
finite element Analysis (FEA). A systematic imaging and modeling
procedure was developed for reliable correspondence between the
QCT-based FEA and the in-vitro mechanical testing. A speciallydesigned
holding frame was used to define and maintain a unique
geometrical reference system during the analysis and testing. The
QCT images were directly converted into voxel-based 3D finite
element models for linear and nonlinear analyses. The equivalent
plastic strain and the strain energy density measures were used to
identify the critical elements and predict the failure patterns. The
samples were destructively tested using a specially-designed gripping
fixture (with five degrees of freedom) mounted within a universal
mechanical testing machine. Very good agreements were found
between the experimental and the predicted failure patterns and the
associated load levels.
Abstract: Cast metal inlays can be used on molars requiring a
class II restoration instead amalgam and offer a durable alternative.
Because it is known that class II inlays may increase the
susceptibility to fracture, it is important to ensure optimal
performance in selection of the adequate preparation design to reduce
stresses in teeth structures and also in the restorations. The aim of the
study was to investigate the influence of preparation design on stress
distribution in molars with different class II preparations and in cast
metal inlays. The first step of the study was to achieve 3D models in
order to analyze teeth and cast metal class II inlays. The geometry of
the intact tooth was obtained by 3D scanning using a manufactured
device. With a NURBS modeling program the preparations and the
appropriately inlays were designed. 3D models of first upper molars
of the same shape and size were created. Inlay cavities designs were
created using literature data. The geometrical model was exported
and the mesh structure of the solid 3D model was created for
structural simulations. Stresses were located around the occlusal
contact areas. For the studied cases, the stress values were not
significant influenced by the taper of the preparation. it was
demonstrated stresses are higher in the cast metal restorations and
therefore the strength of the teeth is not affected.
Abstract: For a quick and accurate calculation of spatial neutron
distribution in nuclear power reactors 3D nodal codes are usually
used aiming at solving the neutron diffusion equation for a given
reactor core geometry and material composition. These codes use a
second order polynomial to represent the transverse leakage term. In
this work, a nodal method based on the well known nodal expansion
method (NEM), developed at COPPE, making use of this polynomial
expansion was modified to treat the transverse leakage term for the
external surfaces of peripheral reflector nodes.
The proposed method was implemented into a computational
system which, besides solving the diffusion equation, also solves the
burnup equations governing the gradual changes in material
compositions of the core due to fuel depletion. Results confirm the
effectiveness of this modified treatment of peripheral nodes for
practical purposes in PWR reactors.
Abstract: A semi-analytic boundary discretization method, the Method of Auxiliary Sources (MAS) is used to analyze Optical Antennas consisting of metallic parts. In addition to standard dipoletype antennas, consisting of two pieces of metal, a new structure consisting of a single metal piece with a tiny groove in the center is analyzed. It is demonstrated that difficult numerical problems are caused because optical antennas exhibit strong material dispersion, loss, and plasmon-polariton effects that require a very accurate numerical simulation. This structure takes advantage of the Channel Plasmon-Polariton (CPP) effect and exhibits a strong enhancement of the electric field in the groove. Also primitive 3D antenna model with spherical nano particles is analyzed.
Abstract: power-line networks are promise infrastructure for
broadband services provision to end users. However, the network
performance is affected by stochastic channel changing which is due
to load impedances, number of branches and branched line lengths. It
has been proposed that multi-carrier modulations techniques such as
orthogonal frequency division multiplexing (OFDM), Multi-Carrier
Spread Spectrum (MC-SS), wavelet OFDM can be used in such
environment. This paper investigates the performance of different
indoor topologies of power-line networks that uses MC-SS
modulation scheme.It is observed that when a branch is added in the
link between sending and receiving end of an indoor channel an
average of 2.5dB power loss is found. In additional, when the branch
is added at a node an average of 1dB power loss is found.
Additionally when the terminal impedances of the branch change
from line characteristic impedance to impedance either higher or
lower values the channel performances were tremendously improved.
For example changing terminal load from characteristic impedance
(85 .) to 5 . the signal to noise ratio (SNR) required to attain the
same performances were decreased from 37dB to 24dB respectively.
Also, changing the terminal load from channel characteristic
impedance (85 .) to very higher impedance (1600 .) the SNR
required to maintain the same performances were decreased from
37dB to 23dB. The result concludes that MC-SS performs better
compared with OFDM techniques in all aspects and especially when
the channel is terminated in either higher or lower impedances.
Abstract: The influence of twist arrangement on the temperature
distribution in an annular diffuser fitted with twisted rectangular hub
is investigated. Different pitches (Y = 120 mm, 100 mm, 80 mm, and
60 mm) for the twist arrangements are simulated to be compared. The
geometry of the annular diffuser and the inlet condition for the hub
arrangements are kept constant. The result reveals that using twisted
rectangular hub insert with different pitches will force the
temperature to distribute in a circular direction. However,
temperature distribution will be enhanced with the length pitch
increases.
Abstract: Bioinformatics and Cheminformatics use computer as disciplines providing tools for acquisition, storage, processing, analysis, integrate data and for the development of potential applications of biological and chemical data. A chemical database is one of the databases that exclusively designed to store chemical information. NMRShiftDB is one of the main databases that used to represent the chemical structures in 2D or 3D structures. SMILES format is one of many ways to write a chemical structure in a linear format. In this study we extracted Antimicrobial Structures in SMILES format from NMRShiftDB and stored it in our Local Data Warehouse with its corresponding information. Additionally, we developed a searching tool that would response to user-s query using the JME Editor tool that allows user to draw or edit molecules and converts the drawn structure into SMILES format. We applied Quick Search algorithm to search for Antimicrobial Structures in our Local Data Ware House.
Abstract: This paper proposes a balance control scheme for a biped robot to trace an arbitrary path using image information. While moving, it estimates the zero moment point(ZMP) of the biped robot in the next step using a Kalman filter and renders an appropriate balanced pose of the robot. The ZMP can be calculated from the robot's pose, which is measured from the reference object image acquired by a CCD camera on the robot's head. For simplifying the kinematical model, the coordinates systems of individual joints of each leg are aligned and the robot motion is approximated as an inverted pendulum so that a simple linear dynamics, 3D-LIPM(3D-Linear Inverted Pendulum Mode) can be applied. The efficiency of the proposed algorithm has been proven by the experiments performed on unknown trajectory.
Abstract: Micro power sources are required to be used in autonomous microelectromechanical system (MEMS). In this paper,
we designed and fabricated a three dimensional (3D) MEMS supercapacitor, which is consisting of conformal silicon
dioxide/titanium/polypyrrole (PPy) layers on silicon substrate. At first, ''through-structure'' was fabricated on the silicon substrate by high-aspect-ratio deep reactive ion etching (DRIE) method, which enlarges the available surface area significantly. Then the SiO2/Ti/PPy layers grew sequentially on the ³through-structure´. Finally, the supercapacitor was investigated by electrochemical methods.
Abstract: Small-scale RC models of both piles and tunnel ducts
were produced as mockups of reality and loaded under soil
confinement conditionsto investigate the damage evolution of
structural RC interacting with soil. Experimental verifications usinga
3D nonlinear FE analysis program called COM3D, which was
developed at the University of Tokyo, are introduced. This analysis
has been used in practice for seismic performance assessment of
underground ducts and in-ground LNG storage tanks in consideration
of soil-structure interactionunder static and dynamic loading. Varying
modes of failure of RCpilessubjected to different magnitudes of soil
confinement were successfully reproduced in the proposed small-scale
experiments and numerically simulated as well. Analytical simulation
was applied to RC tunnel mockups under a wide variety of depth and
soil confinement conditions, and reasonable matching was confirmed.
Abstract: Due to the limited lifetime of the nodes in ad hoc and sensor networks, energy efficiency needs to be an important design consideration in any routing algorithm. It is known that by employing a virtual backbone in a wireless network, the efficiency of any routing scheme for the network can be improved. One common design for routing protocols in mobile ad hoc networks is to use positioning information; we use the node-s geometric locations to introduce an algorithm that can construct the virtual backbone structure locally in 3D environment. The algorithm construction has a constant time.
Abstract: Among many different methods that are used for
optimizing different engineering problems mathematical (numerical)
optimization techniques are very important because they can easily
be used and are consistent with most of engineering problems. Many
studies and researches are done on stability analysis of three
dimensional (3D) slopes and the relating probable slip surfaces and
determination of factors of safety, but in most of them force
equilibrium equations, as in simplified 2D methods, are considered
only in two directions. In other words for decreasing mathematical
calculations and also for simplifying purposes the force equilibrium
equation in 3rd direction is omitted. This point is considered in just a
few numbers of previous studies and most of them have only given a
factor of safety and they haven-t made enough effort to find the most
probable slip surface. In this study shapes of the slip surfaces are
modeled, and safety factors are calculated considering the force
equilibrium equations in all three directions, and also the moment
equilibrium equation is satisfied in the slip direction, and using
nonlinear programming techniques the shape of the most probable
slip surface is determined. The model which is used in this study is a
3D model that is composed of three upper surfaces which can cover
all defined and probable slip surfaces. In this research the meshing
process is done in a way that all elements are prismatic with
quadrilateral cross sections, and the safety factor is defined on this
quadrilateral surface in the base of the element which is a part of the
whole slip surface. The method that is used in this study to find the
most probable slip surface is the non-linear programming method in
which the objective function that must get optimized is the factor of
safety that is a function of the soil properties and the coordinates of
the nodes on the probable slip surface. The main reason for using
non-linear programming method in this research is its quick
convergence to the desired responses. The final results show a good
compatibility with the previously used classical and 2D methods and
also show a reasonable convergence speed.